| Age | Commit message (Collapse) | Author |
|---|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Miri Korenblit says:
====================
iwlwifi feature, notably
- disable features in fips
- remove RX OMI feature code
- A few fixes and cleanups
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In missed beacon handling, we compare the FW link id to the
bss_param_ch_cnt_link_id, which is a spec link id. Fix it.
Reviewed-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250723094230.2104f8cac836.I25ed77c2b87bde82a9153e2aa26e09b8a42f6ee3@changeid
|
|
Only the EOF bit handling for single frames was ported to the MLD
driver. The code to handle AMPDUs correctly was forgotten. Add it back
so that the bit is reported in the radiotap headers again.
Fixes: d1e879ec600f ("wifi: iwlwifi: add iwlmld sub-driver")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250723094230.195be86372d5.I4db4abf348f7b6dfc75f869770dd77655a204bc7@changeid
|
|
This feature turns out to have an issue: it can take up to 8 seconds to
detect high throughput scenarios and to leave RX OMI bandwidth
reduction. This leads to throughput degradation.
Until the issues are fixed, remove the RX OMI implementation.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250723094230.a9ccfe210516.Ic87bc7709a6761f593e88f1488a41442c68c1686@changeid
|
|
This version doesn't provide the sta id, so we need to look it up -
assuming that no other sta exists, since one of the conditions of
entering OMI is not having P2P/TDLS.
But when we leave OMI, because of the P2P/TDLS activation, the P2P/TDLS
sta can already exist while we receive the notification from the FW.
This causes an error log which is incorrect.
Since OMI is only supported in SC, which is not shipped yet, no one will
use a FW with the old version.
Remove support for it.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250723094230.b716b9cebaa7.I2a1cc4be441dbbb5566a9a3d2d330d956ff3ed38@changeid
|
|
If no frames are received on a queue for a while, the reorder buffer
head_sn may be an old one. When the next frame that is received on
that queue and buffered is a subframe of an AMSDU but not the last
subframe, it will not update the buffer's head_sn. When the frame
release notification arrives, it will not release the buffered frame
because it will look like the notification's NSSN is lower than the
buffer's head_sn (because of a wraparound).
Fix it by updating the head_sn when the first frame is buffered.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250723094230.e1f62a9a603c.I7b57a481122074b1f40d39cd31db2e5262668eb2@changeid
|
|
When fips_enabled is set, keys will not be given to the
hardware by mac80211 since the hardware isn't certified.
In this case, various features cannot work correctly as
the firmware needs to handle frames, but it then cannot
since no keys are available.
Disable features:
- WoWLAN since no keys etc.
- MFP since some frames need to be handled in firmware
- EHT/6GHz since MFP is required
Also restrict A-MSDU size since A-MSDUs cannot be split
up by hardware and thus need to fit into the RX buffers
in one piece.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250723094230.329fade58a27.I0be27dd329643cc5fdf79a8c8b8f6d2e6fb5c175@changeid
|
|
The firmware is able to collect channel statistics when doing passive
scans. Enable the flag when doing a passive scan on an AP interface and
collect the survey information.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250723094230.a659ef1b1fd8.I24a9a0383327c231f36be170968bc7bac801f9f2@changeid
|
|
The user can request to disable RX aggregations via the module parameter
enable_11n.
Honor this request and reject addba.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250723094230.40746586ade7.Ibf5877df76ea2f1eee614166b3194843fd9898cd@changeid
|
|
ieee80211_add_gtk_rekey receives a keyconf as an argument, and the
cipher and keylen are taken from there to the new allocated key.
But in rekey, both the cipher and the keylen should be the same as of
the old key, so let ieee80211_add_gtk_rekey find those, so drivers won't
have to fill it in.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250721214922.3c5c023bfae9.Ie6594ae2b4b6d5b3d536e642b349046ebfce7a5d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
iwlmld was planned to be used for HR/GF, which has versions 5/6,
but it was decided at the end to use iwlmvm for HR/GF, so iwlmld only
needs to support version 8.
Remove versions 5 and 6 support.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250711183056.9c64bfbb16cb.I109bee4d4bf455cbffbb8d2340023338bcab886d@changeid
|
|
when BT is ON"
Due to a hw bug, this feature won't be enabled. Revert its
implementation.
This reverts commit 37808a3788fd ("wifi: iwlwifi: mld: allow EMLSR with
2.4 GHz when BT is ON")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250711183056.57755ac3f39d.I63ae0ee3e6cdc9b11175ad15927aaad3b8f8f47a@changeid
|
|
with bt on"
Due to a hw bug, this feature won't be enabled. Revert its tests.
This reverts commit f7cc80b871ee ("wifi: iwlwifi: mld: add kunit test
for emlsr with bt on")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250711183056.5fdf77497ad2.I1160f1dcff734cb42baa8fbf8aac121a1a24a4c5@changeid
|
|
The firmware provides the station id, use it since it makes our lives
easier. No need to assume we have a single BSS vif, and look up the
station id to whom the OMI was sent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250711183056.7d2cd878855f.I8625ebb2c4e1fb484aafd16a07549f2eeb506e08@changeid
|
|
iwlmld was planned to be used for HR/GF, which has version 4,
but it was decided at the end to use iwlmvm for HR/GF, so iwlmld only
needs to support version 5.
Remove version 4 support.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250711183056.faeb1e6bac2a.I1a29b16f59b67c103d1f91dedee27e04cd7fdfdd@changeid
|
|
iwlmld was planned to be used for HR, which has version 9,
but it was decided at the end to use iwlmvm for HR, so iwlmld only
needs to support version 10.
Remove version 9 support.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250711183056.aeeb617abfae.I05101972506180644c42be5096c1b2afa36c625a@changeid
|
|
When connected to an AP, the PHY will typically be tuned to
a higher bandwidth than the beacons are transmitted on, as
they are normally only transmitted on 20 MHz. This can mean
that another STA is simultaneously transmitting on another
channel of the higher bandwidth, and apparently this energy
may be taken into account by the PHY, resulting in elevated
energy readings.
To work around this, track the firmware's corrected beacon
energy data and replace the RSSI in beacons by that. The
replacement happens for all beacons received in the context
of the current MAC or link (depending on FW version), in
which case the filters will drop all else. For a scan, which
is only tuning to 20 MHz channels, the MAC/link ID will be
one that isn't found (the AUX ID 4), and no correction will
be done (nor is it needed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250711183056.324bfe7027ff.I160f947e7aab30e0110a7019ed46186e57c3de14@changeid
|
|
Firmware would assert on undefined bits in DSM-originated DWs.
With this change, Firmware introduces a fail-safe mechanism
and removes the assert behavior. This ensures robustness when
handling raw DSM table data.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250710212632.eee871df03c9.I2be2eaa16437e84aa1be0c6c95ec334034ce7e50@changeid
|
|
In the current code, if there was a rekey, we remove all the existing keys
from mac80211, then re-add the ones that the FW sent with
ieee80211_gtk_rekey_add, (newer FW will send also the existing GTKs/BIGTKs)
and then update the sequence number.
Instead of removing and re-adding the existing keys for no good reason,
we can just update the sequence of all keys, also of the ones that are
going to be replaced, and update again after the replace.
This change is required because ieee80211_gtk_rekey_add is going to be
changed to lookup the cipher from the old key instead of receiving it as an
argument, and for this it will need the old key(s), so we can't remove all
keys.
Note that with this change, in case that a key that existed before wowlan
is replaced, mac80211 will now call the driver to remove the old key and
add the new one (as opposed the previous behaviour, in which the key was
removed by the driver itself).
Of course we don't want to run the set_key callbacks in this case, so just
return early.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250710212632.f0b5e19f77f5.I958f4926f168cdad6d4d7720ebde2f5e812b297d@changeid
|
|
Add iwl_trans_is_dead() function to be called by the op modes instead
of directly checking the trans status bits. This hides the trans
internal implementation details from callers.
Signed-off-by: Rotem Kerem <rotem.kerem@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250710212632.cd89d8013261.I214b7ffbabc393593fb57831d61d1a9ffa318a1e@changeid
|
|
Add iwl_trans_suppress_cmd_error_once() function to be called by the op
modes instead of directly checking the trans status bits.
This hides the trans internal implementation details from callers.
Signed-off-by: Rotem Kerem <rotem.kerem@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250710212632.e061ae241fd3.Ie2043c4e237196ebcfe195006d3d76371de48a55@changeid
|
|
Later RFs will always do puncturing, regardless of BIOS
configuration, and earlier RFs aren't supported in MLD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250710212632.6fa9c44964c1.I46a4cd744a769ec2ac3c8f9a04882140449394b8@changeid
|
|
The last version for the range response notification is 10.
Update the expected version accordingly.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250710212632.377d24e29ac6.I44119a4e793bba35b46e1d35e2c378ce6f901bfd@changeid
|
|
When a GO is started, the P2P device mac is updated to indicate
that frames for the P2P device mac should be filtered in while
the GO is active. However, this configuration is done after the GO is
already started so it doesn't take effect. Fix it by updating the
P2P device mac before adding the broadcast station, which actually
starts the GO.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250710212632.463a0ad545f9.I85a25484d787b65f6a27e794285911e319df0b2d@changeid
|
|
The scan request validation function uses bitwise and instead
of logical and. Fix it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250710212632.ec7d665f56a4.I416816b491fafa5d3efdf0a4be78356eedf2bd95@changeid
|
|
These have no real value for normal users, print them as
debug messages instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250709081300.bd2df0705d89.Ic6f042588ef17719653c077ff89a8b9149c22f92@changeid
|
|
Given compatibility issues with external PNVM data that doesn't match
the firmware it was designed with/for, future firmware releases will
include the PNVM data in the firmware files directly, avoiding those
mismatch issues. Make the driver load and use that embedded PNVM data
in preference of external files, falling back to the external file if
it isn't present.
Co-developed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250709081300.c843f77aa2d3.I7200f8dd40ef82aff1f5574fdd3966913cda592c@changeid
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Miri Korenblit says:
====================
iwlwifi-next - iwlwifi features
Mostly cleanups. A few fixes and small features.
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The terminating brace for the switch statement is erroneously
not indented, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250422160017.6d4cff49cbf4.I8e5570a6fe94faa9f17a89352b7ba645fc875e77@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
There is a requirement to exit EMLSR if there wasn't enough throughput
in the secondary link.
This is checked in check_tpt_wk, which runs every 5 seconds in a high
throughput scenario (when the throughput blocker isn't set)
It can happen that this worker is running immediately after we entered
EMLSR, and in that case the secondary link didn't have a chance to have
throughput. In that case we will exit EMLSR for no good reason.
Fix this by tracking the time we entered EMLSR, and in the worker make
sure that 5 seconds passed from when we entered EMLSR. If not, don't
check the secondary link throughput.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.c680f8d7dc37.I8a02d1e8d99df3789da8d5714f19b31a865a61ff@changeid
|
|
No one checks its return value anyway.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.4c38fb4c48f4.Ia62100a54370b6af5e528ba10c8f21e177018096@changeid
|
|
The iwlmld driver is able to handle TTLM changes as long as all TIDs
have the same TID to Link Mapping. Add the corresponding code so that
mac80211 will accept and trigger the TTLM change.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.3b0a4fd2c12b.I1fab7840f1cc222bd1e8cb58ac1a4177474fcd56@changeid
|
|
Temporarily block EMLSR when scanning on a P2P Device interface,
as this is an indication that P2P activity is about to start, e.g.,
P2P client connection to a P2P GO.
Since a P2P scan while a station interface connection is active might
be long, increase the EMLSR blocking timeout to 10 seconds.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.85fb79d537fe.I27523f8d3f00f2b66f5f555f098e323be29465ea@changeid
|
|
For the iwlmld driver the RX command is using struct iwl_rx_mpdu_desc
and not the much older struct iwl_rx_mpdu_res_start. Adjust the value of
rx_mpdu_cmd_hdr_size accordingly so that the trace data is correct.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.688d95d99ff3.Id3055ca6c19cf8c821cbbd80c09ca2a21d9acec7@changeid
|
|
This means nothing to a normal user and really has no value
for most people, print it as a debug message instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.ee6254c03a33.I2cf4e1e2e604b42b6eb9737c0ef3b75fec69edea@changeid
|
|
Doing a scan right after link activation can be less reliable
than at other times, as the firmware is still busy trying to
catch beacons from the just activated link, etc. In case a new
MLO scan request comes in, defer it for a few seconds after a
link activation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.09548e958a9e.I24dbfd425da260f3ae6fa5a48fe25bd4ab6fcf99@changeid
|
|
This should be u64, otherwise it rolls over quickly on 32-bit
systems.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.5381030253cd.I4e3a7bca5b52fc826e26311055286421508c4d1b@changeid
|
|
The (applicable) firmware versions will send an error interrupt as
part of the resume process, so there's no need now to check for it
explicitly. Simplify the code. This also fixes an issue where any
dump taken during the resume isn't able to do the reset handshake
as part of the dump (since interrupts are disabled) and then there
isn't all the correct data and we get more errors later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.9e778f1bae0c.I96483b5236ab23141b45079464c73f93e0164e65@changeid
|
|
Add a debugfs file to be able to control how long, at most,
the device will sleep before waking up the host. This will
be useful to test certain "assert during suspend" scenarios
for the previous change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.9f2a39cae1e1.Ie0003f21286fea50b507d0debe06332b030cd4cb@changeid
|
|
Implement a dump handler in the iwl_mld operation mode to
collect firmware dump upon trigger from trans layer.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250611222325.18ebf46690ce.Ia52941f761a446cb3e43cbe49d2b9a49fc15f4a8@changeid
|
|
This got pretty mangled, fix the spelling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250609211928.afbb67d4dda9.Id1412d9336740e6101e672b38411641c6e206999@changeid
|
|
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The initialization of async_handlers_list
was accidentally removed in a previous change.
Then it was restoted by commit 175e69e33c66 ("wifi: iwlwifi: restore
missing initialization of async_handlers_list").
Somehow, the initialization disappeared again.
Restote it.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Respect this flag and don't scan for another link if it is set.
Signed-off-by: Itamar Shalev <itamar.shalev@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250609211928.9ecb5c5301d4.I88b37e93d9ba66d4381f4976541b4aca2a20e36e@changeid
|
|
Respect this flag before initiating MLO scan.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250609211928.b5c7fbdcb15c.Iaa176c49142b46b0b896728005357faec6a55fa6@changeid
|
|
Those are internal files so they should not be compiled.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250609211928.3bfe5222fe79.I1ebd746b0c513e278d231b5c48f5438ca9b9231f@changeid
|
|
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from CAN, wireless, Bluetooth, and Netfilter.
Current release - regressions:
- Revert "kunit: configs: Enable CONFIG_INIT_STACK_ALL_PATTERN in
all_tests", makes kunit error out if compiler is old
- wifi: iwlwifi: mvm: fix assert on suspend
- rxrpc: fix return from none_validate_challenge()
Current release - new code bugs:
- ovpn: couple of fixes for socket cleanup and UDP-tunnel teardown
- can: kvaser_pciefd: refine error prone echo_skb_max handling logic
- fix net_devmem_bind_dmabuf() stub when DEVMEM not compiled
- eth: airoha: fixes for config / accel in bridge mode
Previous releases - regressions:
- Bluetooth: hci_qca: move the SoC type check to the right place, fix
GPIO integration
- prevent a NULL deref in rtnl_create_link() after locking changes
- fix udp gso skb_segment after pull from frag_list
- hv_netvsc: fix potential deadlock in netvsc_vf_setxdp()
Previous releases - always broken:
- netfilter:
- nf_nat: also check reverse tuple to obtain clashing entry
- nf_set_pipapo_avx2: fix initial map fill (zeroing)
- fix the helper for incremental update of packet checksums after
modifying the IP address, used by ILA and BPF
- eth:
- stmmac: prevent div by 0 when clock rate is misconfigured
- ice: fix Tx scheduler handling of XDP and changing queue count
- eth: fix support for the RGMII interface when delays configured"
* tag 'net-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
calipso: unlock rcu before returning -EAFNOSUPPORT
seg6: Fix validation of nexthop addresses
net: prevent a NULL deref in rtnl_create_link()
net: annotate data-races around cleanup_net_task
selftests: drv-net: tso: make bkg() wait for socat to quit
selftests: drv-net: tso: fix the GRE device name
selftests: drv-net: add configs for the TSO test
wireguard: device: enable threaded NAPI
netlink: specs: rt-link: decode ip6gre
netlink: specs: rt-link: add missing byte-order properties
net: wwan: mhi_wwan_mbim: use correct mux_id for multiplexing
wifi: cfg80211/mac80211: correctly parse S1G beacon optional elements
net: dsa: b53: do not touch DLL_IQQD on bcm53115
net: dsa: b53: allow RGMII for bcm63xx RGMII ports
net: dsa: b53: do not configure bcm63xx's IMP port interface
net: dsa: b53: do not enable RGMII delay on bcm63xx
net: dsa: b53: do not enable EEE on bcm63xx
net: ti: icssg-prueth: Fix swapped TX stats for MII interfaces.
selftests: netfilter: nft_nat.sh: add test for reverse clash with nat
netfilter: nf_nat: also check reverse tuple to obtain clashing entry
...
|
|
The regulatory domain information was initialized every time the
FW was loaded and the device was restarted. This was unnecessary
and useless as at this stage the wiphy channels information was
not setup yet so while the regulatory domain was set to the wiphy,
the channel information was not updated.
In case that a specific MCC was configured during FW initialization
then following updates with this MCC are ignored, and thus the
wiphy channels information is left with information not matching
the regulatory domain.
This commit moves the regulatory domain initialization to after the
operational firmware is started, i.e., after the wiphy channels were
configured and the regulatory information is needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250604061200.f138a7382093.I2fd8b3e99be13c2687da483e2cb1311ffb4fbfce@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
In case of an error during init, in_hw_restart will be set, but it will
never get cleared.
Instead, we will retry to init again, and then we will act like we are in a
restart when we are actually not.
This causes (among others) to a NULL pointer dereference when canceling
rx_omi::finished_work, that was not even initialized, because we thought
that we are in hw_restart.
Set in_hw_restart to true only if the fw is running, then we know that
FW was loaded successfully and we are not going to the retry loop.
Fixes: 7391b2a4f7db ("wifi: iwlwifi: rework firmware error handling")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250604061200.e0040e0a4b09.Iae469a0abe6bfa3c26d8a88c066bad75c2e8f121@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
