| Age | Commit message (Collapse) | Author |
|---|
|
WCN7850 uses error dst ring as mon dest ring. Each time hardware
receives a packet, will fill the payload into mon dest ring.
The mon dest ring may store many MSDUs, which belonged to different
MPDUs. Need to retrieve MSDUs based on the PPDU ID, only processing the
MSDUs with same PPDU ID each time.
The PPDU ID is used in cycles, the difference between the PPDU IDs
of the two rings must be checked. If the status PPDU ID minus the
dest PPDU ID is greater than 20000, it is considered a wrap-around
case.
After reaping the mon dest ring, should prepare packet and deliver it to
mac80211 when status PPDU ID is equal to dest PPDU ID. Then start to
process next PPDU if exists.
But if dest PPDU ID > status PPDU ID, should hold on to mon dest ring
processing. If it exceeds 16 consecutive times, status PPDU ID will be
forcibly set to dest PPDU ID to avoid backpressure issue.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-11-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, ath12k_dp_rx_link_desc_return() takes struct
hal_reo_dest_ring as its second input. This struct is converted to
struct hal_wbm_release_ring and passed into
ath12k_hal_rx_msdu_link_desc_set(), where it is converted again.
This double conversion is both strange and inefficient.
In ath12k_hal_rx_msdu_link_desc_set(), only buf_addr_info is actually
used. To simplify the code and improve readability, directly passes
buf_addr_info when calling ath12k_dp_rx_link_desc_return().
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-10-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, in the monitor Rx path, status is filled from the RX TLV header
present in the MSDU data. This logic is inherited from ath11k. However, in
the ath12k 802.11be hardware, the Rx TLV header is not present in the MSDU
data. This information is reported under various TLV tags. Therefore, avoid
the existing status filling by accumulating the needed information in the
PPDU information structure and fill the status.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250324062518.2752822-6-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, the monitor Rx parser handler is inherited from the ath11k.
However, the ath12k 802.11be hardware does not report the Rx TLV header
in the MSDU data. Instead, the hardware reports those TLVs under the
following TLV tags:
1. Buffer address
2. MPDU start
3. MPDU end
4. MSDU end
Therefore, add support for parsing the above TLVs in the Rx monitor path
and use this information for MSDU buffer and status updates.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250324062518.2752822-3-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, peer extended Rx statistics are not supported. Therefore, expose
peer extended Rx statistics support through debugfs, allowing users to
enable or disable the collection of statistics information. After that
the statistics information can be dumped through debugfs. Below are the
debugfs commands exposed.
Enable/Disable:
echo <1/0> > /sys/kernel/debug/ieee80211/phyX/ath12k/ext_rx_stats
Dump:
cat /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/<peer MAC addr>/rx_stats
Sample output:
==============
RX peer stats:
Num of MSDUs: 1087
Num of MSDUs with TCP L4: 0
Num of MSDUs with UDP L4: 13
Num of other MSDUs: 1074
Num of MSDUs part of AMPDU: 363
Num of MSDUs not part of AMPDU: 724
Num of MSDUs using STBC: 0
Num of MSDUs beamformed: 0
Num of MPDUs with FCS ok: 695
Num of MPDUs with FCS error: 0
preamble: 11A 395 11B 0 11N 0 11AC 0 11AX 692 11BE 0
reception type: SU 1087 MU_MIMO 0 MU_OFDMA 0 MU_OFDMA_MIMO 0
TID(0-15) Legacy TID(16):690 1 0 0 1 0 0 0 0 0 0 0 0 0 0 0 395
RX Duration:39537
DCM: 0
RU26: 0
RU52: 0
RU106: 0
RU242: 0
RU484: 0
RU996: 0
RX success packet stats:
EHT stats:
MCS 0: 0 MCS 1: 0 MCS 2: 0 MCS 3: 0 MCS 4: 0 MCS 5: 0 MCS 6: 0 MCS 7: 0
MCS 8: 0 MCS 9: 0 MCS 10: 0 MCS 11: 0 MCS 12: 0 MCS 13: 0 MCS 14: 0 MCS 15: 0
HE stats:
MCS 0: 1 MCS 1: 0 MCS 2: 0 MCS 3: 0 MCS 4: 0 MCS 5: 0
MCS 6: 66 MCS 7: 46 MCS 8: 46 MCS 9: 34 MCS 10: 28 MCS 11: 471
VHT stats:
MCS 0: 0 MCS 1: 0 MCS 2: 0 MCS 3: 0 MCS 4: 0
MCS 5: 0 MCS 6: 0 MCS 7: 0 MCS 8: 0 MCS 9: 0
HT stats:
MCS 0: 0 MCS 1: 0 MCS 2: 0 MCS 3: 0 MCS 4: 0 MCS 5: 0 MCS 6: 0 MCS 7: 0
MCS 8: 0 MCS 9: 0 MCS 10: 0 MCS 11: 0 MCS 12: 0 MCS 13: 0 MCS 14: 0 MCS 15: 0
MCS 16: 0 MCS 17: 0 MCS 18: 0 MCS 19: 0 MCS 20: 0 MCS 21: 0 MCS 22: 0 MCS 23: 0
MCS 24: 0 MCS 25: 0 MCS 26: 0 MCS 27: 0 MCS 28: 0 MCS 29: 0 MCS 30: 0 MCS 31: 0
Legacy stats:
1 Mbps: 0 2 Mbps: 0 5.5 Mbps: 0 6 Mbps: 395
9 Mbps: 0 11 Mbps: 0 12 Mbps: 0 18 Mbps: 0
24 Mbps: 0 36 Mbps: 0 48 Mbps: 0 54 Mbps: 0
NSS stats:
1x1: 1086 2x2: 0 3x3: 0 4x4: 0 5x5: 0 6x6: 0 7x7: 0 8x8: 0
GI: 0.8 us 0 0.4 us 396 1.6 us 691 3.2 us 0
BW: 20 MHz 785 40 MHz 2 80 MHz 300 160 MHz 0 320 MHz 0
20 Mhz gi 1 us 1x1 : 6:5 7:3 8:3 9:4 10:4 11:374 12:391
40 Mhz gi 1 us 1x1 : 12:2
80 Mhz gi 1 us 1x1 : 6:61 7:43 8:43 9:30 10:24 11:97 12:2
RX success byte stats:
EHT stats:
MCS 0: 0 MCS 1: 0 MCS 2: 0 MCS 3: 0 MCS 4: 0 MCS 5: 0 MCS 6: 0 MCS 7: 0
MCS 8: 0 MCS 9: 0 MCS 10: 0 MCS 11: 0 MCS 12: 0 MCS 13: 0 MCS 14: 0 MCS 15: 0
HE stats:
MCS 0: 41 MCS 1: 0 MCS 2: 0 MCS 3: 0 MCS 4: 0 MCS 5: 0
MCS 6: 1435 MCS 7: 943 MCS 8: 697 MCS 9: 533 MCS 10: 492 MCS 11: 8159
VHT stats:
MCS 0: 0 MCS 1: 0 MCS 2: 0 MCS 3: 0 MCS 4: 0
MCS 5: 0 MCS 6: 0 MCS 7: 0 MCS 8: 0 MCS 9: 0
HT stats:
MCS 0: 0 MCS 1: 0 MCS 2: 0 MCS 3: 0 MCS 4: 0 MCS 5: 0 MCS 6: 0 MCS 7: 0
MCS 8: 0 MCS 9: 0 MCS 10: 0 MCS 11: 0 MCS 12: 0 MCS 13: 0 MCS 14: 0 MCS 15: 0
MCS 16: 0 MCS 17: 0 MCS 18: 0 MCS 19: 0 MCS 20: 0 MCS 21: 0 MCS 22: 0 MCS 23: 0
MCS 24: 0 MCS 25: 0 MCS 26: 0 MCS 27: 0 MCS 28: 0 MCS 29: 0 MCS 30: 0 MCS 31: 0
Legacy stats:
1 Mbps: 0 2 Mbps: 0 5.5 Mbps: 0 6 Mbps: 16195
9 Mbps: 0 11 Mbps: 0 12 Mbps: 0 18 Mbps: 0
24 Mbps: 0 36 Mbps: 0 48 Mbps: 0 54 Mbps: 0
NSS stats:
1x1: 28454 2x2: 0 3x3: 0 4x4: 0 5x5: 0 6x6: 0 7x7: 0 8x8: 0
GI: 0.8 us 0 0.4 us 16236 1.6 us 12259 3.2 us 0
BW: 20 MHz 24108 40 MHz 82 80 MHz 4305 160 MHz 0 320 MHz 0
20 Mhz gi 1 us 1x1 : 6:205 7:123 8:123 9:164 10:164 11:7257 12:16031
40 Mhz gi 1 us 1x1 : 12:82
80 Mhz gi 1 us 1x1 : 6:1230 7:820 8:574 9:369 10:328 11:902 12:82
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-10-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, ampdu id is update with peer id mask which is incorrect.
Therefore, update the ampdu id with PPDU id mask value. Also move
the ampdu_id field inside the user stats since it is a user id based
statistics.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-7-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, monitor is not enabled. However, in the future, the monitor
will be enabled. Therefore, add the necessary HAL_PHYRX_OTHER_RECEIVE_INFO
TLV parsing support in the monitor Rx path, which helps to populate the
extended Rx statistics.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-5-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, monitor is not enabled. However, in the future, the monitor
will be enabled. Therefore, add necessary HAL_RX_PPDU_START_USER_INFO TLV
parsing support in monitor Rx path, which help to populate the EHT radiotap
data.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-4-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, monitor is not enabled. However, in the future, the monitor
will be enabled. Therefore, add the necessary HAL_PHYRX_GENERIC_EHT_SIG
TLV parsing support in monitor Rx path, which help to populate the EHT
radiotap data.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-3-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, monitor is not enabled. However, in the future, the monitor
will be enabled. Therefore, add the necessary HAL_PHYRX_GENERIC_U_SIG TLV
parsing support in monitor Rx path, which help to populate the EHT
radiotap data.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-2-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Driver uses monitor destination rings for extended statistics mode and
standalone monitor mode. In extended statistics mode, TLVs are parsed from
the buffer received from the monitor destination ring and assigned to the
ppdu_info structure to update per-packet statistics. In standalone monitor
mode, along with per-packet statistics, the packet data (payload) is
captured, and the driver updates per MSDU to mac80211.
When the AP interface is enabled, only extended statistics mode is
activated. As part of enabling monitor rings for collecting statistics,
the driver subscribes to HAL_RX_MPDU_START TLV in the filter
configuration. This TLV is received from the monitor destination ring, and
kzalloc for the mon_mpdu object occurs, which is not freed, leading to a
memory leak. The kzalloc for the mon_mpdu object is only required while
enabling the standalone monitor interface. This causes a memory leak while
enabling extended statistics mode in the driver.
Fix this memory leak by removing the kzalloc for the mon_mpdu object in
the HAL_RX_MPDU_START TLV handling. Additionally, remove the standalone
monitor mode handlings in the HAL_MON_BUF_ADDR and HAL_RX_MSDU_END TLVs.
These TLV tags will be handled properly when enabling standalone monitor
mode in the future.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-13-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Each PPDU contains numerous TLV tags. HAL_RX_PPDU_START marks the start
of the PPDU, and HAL_RX_PPDU_END_STATUS_DONE marks the end. From the
monitor destination rings, the driver retrieves skb containing these
TLV tags and their corresponding data. Sometimes, one PPDU’s information
spreads across multiple skbs. The current parsing logic uses memset on
struct hal_rx_mon_ppdu_info after parsing each skb, leading to information
loss if a PPDU spans multiple skbs. Fix this by setting the
ppdu_continuation flag when the driver fails to get
HAL_RX_PPDU_END_STATUS_DONE, and do memset on struct
hal_rx_mon_ppdu_info only when the ppdu_continuation flag is not set.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-12-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, the transmit rate of "iw dev xxx station dump" command
always show an invalid value.
To address this issue, ath12k parse the info of transmit complete
report from firmware and indicate the transmit rate to mac80211.
This patch affects the station mode of WCN7850 and QCN9274.
After that, "iw dev xxx station dump" show the correct transmit rate.
Such as:
Station 00:03:7f:12:03:03 (on wlo1)
inactive time: 872 ms
rx bytes: 219111
rx packets: 1133
tx bytes: 53767
tx packets: 462
tx retries: 51
tx failed: 0
beacon loss: 0
beacon rx: 403
rx drop misc: 74
signal: -95 dBm
beacon signal avg: -18 dBm
tx bitrate: 1441.1 MBit/s 80MHz EHT-MCS 13 EHT-NSS 2 EHT-GI 0
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219715
Link: https://patch.msgid.link/20250115063537.35797-2-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, CODING and TXBF are unused masks defined in the HAL Rx monitor
status TLV parsing code path. Therefore, remove the unused masks to
prevent incorrect assumptions for code readers.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-7-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The following TLV structures and bitmask definitions were inherited from
the ath11k but were not updated for the ath12k 802.11be hardware. These
data structure and bitmask will be used to parse the monitor status
TLV data in the Rx path.
1. hal_rx_ppdu_end_user_stats_ext structure
2. hal_rx_ppdu_end_duration structure
3. HAL_RX_HE_SIG_B2_OFDMA_INFO_INFO0_STA_TXBF bitmask
4. HAL_RX_MPDU_START_INFO1_PEERID bitmask
5. HAL_INVALID_PEERID
6. hal_rx_ppdu_end_user_stats bitmask
Currently, there is no issue since the monitor status Rx path is not
enabled. However, in the future, the monitor status Rx path will be
enabled. Therefore, update the above TLV structures and bitmask to align
with the ath12k 802.11be hardware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-3-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Current struct hal_rx_mpdu_start in hal_rx.h is not matched with
hardware descriptor definition. This hardware descriptor definition
is determined by hardware. Host shall follow it.
So update struct hal_rx_mpdu_start and related code.
Both QCN9274 and WCN7850 need this modification.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241022110831.974-6-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
|
|
Current struct hal_rx_phyrx_rssi_legacy_info in hal_rx.h is not matched
with hardware descriptor definition. This hardware descriptor definition
is determined by hardware. Host shall follow it.
So update struct hal_rx_phyrx_rssi_legacy_info and related code.
Both QCN9274 and WCN7850 need this modification.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241022110831.974-5-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
|
|
Current struct hal_rx_ppdu_start in hal_rx.h is not matched with
hardware descriptor definition. This hardware descriptor definition
is determined by hardware. Host shall follow it.
So update struct hal_rx_ppdu_start and related code.
Both QCN9274 and WCN7850 need this modification.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Link: https://patch.msgid.link/20241022110831.974-4-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
|
|
Current struct hal_rx_ppdu_end_user_stats in hal_rx.h is not matched
with hardware descriptor definition. This hardware descriptor definition
is determined by hardware. Host shall follow it.
So update struct hal_rx_ppdu_end_user_stats and related code.
Both QCN9274 and WCN7850 need this modification.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241022110831.974-3-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
|
|
Add 320 MHz bandwidth as a new bandwidth enum for ATH12k driver. This
is extending existing bandwidth related enums to include 320 MHz. This
is a precursor to supporting 320 MHz in the future.
Sanity test performed to confirm that there was no impact in existing
bandwidths.
Additionally update QuIC copyright to include 2023 in hal_rx.h.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00125-QCAHKSWPL_SILICONZ-1
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231116221839.1303170-1-quic_msinada@quicinc.com
|
|
ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first
supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP
and station; WCN7850 supports only station mode. Monitor mode is not
(yet) supported. Only PCI bus devices are supported.
ath12k is forked from an earlier version of ath11k. It was simpler to
have a "clean start" for the new generation and not try to share the
code with ath11k. This makes maintenance easier and avoids major
changes in ath11k, which would have significantly increased the risk
of regressions in existing setups.
ath12k uses le32 and cpu_to_le32() macros to handle endian
conversions, instead of using the firmware byte swap feature utilized
by ath11k. There is only one kernel module, named ath12k.ko.
Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but
work is ongoing to add EHT mode (IEEE 802.11be) support.
The size of the driver is ~41 kLOC and 45 files. To make the review
easier, this initial version of ath12k does not support Device Tree,
debugfs or any other extra features. Those will be added later, after
ath12k is accepted to upstream.
The driver is build tested by Intel's kernel test robot with both GCC
and Clang. Sparse reports no warnings. The driver is mostly free of
checkpatch warnings, albeit few of the warnings are omitted on
purpose, list of them here:
https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52
The driver has had multiple authors who are listed in alphabetical
order below.
Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
|
