| Age | Commit message (Collapse) | Author |
|---|
|
Add support for the OOB layout used by the ROM bootloader.
The same layout is used by both Keystone [1] and OMAPL138/DA850 [2]
which currently is the only users of davinci-nand.
Only select this layout if the `nand-is-boot-medium` property is set.
This to avoid breaking any existing devices out there.
[1] https://www.ti.com/lit/ug/spruhj3/spruhj3.pdf
[2] https://www.ti.com/lit/an/sprab41f/sprab41f.pdf
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
For each NAND_OP_WAITRDY_INSTR operation, the NANDFSR register is
polled only once every 100 us to check for the EMA_WAIT pin. This
isn't frequent enough and causes delays in NAND accesses.
Set the polling interval to 5 us. It increases the page read speed
reported by flash_speed by ~30% (~10% on page writes).
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The setup_interface() operation isn't implemented. It forces the driver
to use the ONFI mode 0, though it could use more optimal modes.
Implement the setup_interface() operation. It uses the
aemif_set_cs_timings() function from the AEMIF driver to update the
chip select timings. The calculation of the register's contents is
directly extracted from §20.3.2.3 of the DaVinci TRM [1]
MAX_TH_PS and MAX_TSU_PS are the worst case timings based on the
Keystone2 and DaVinci datasheets.
[1] : https://www.ti.com/lit/ug/spruh77c/spruh77c.pdf
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
NAND controller has a reference clock inherited from the AEMIF
(cf. Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt)
This clock isn't used yet by the driver.
Add a struct clock in the struct davinci_nand_info so it can be used
to compute timings.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Some chips, e.g. Micron MT29F1G08ABBFAH4, has a mandatory on-die ECC.
Add "on-die" as ECC engine type in order to be compatible with those.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI-NAND changes:
A load of fixes to Winbond manufacturer driver have been done, plus a
structure constification.
Raw NAND changes:
The GPMI driver has been improved on the power management side.
The Davinci driver has been cleaned up.
A leak in the Atmel driver plus some typos in the core have been fixed.
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/mtd to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007205803.444994-10-u.kleine-koenig@baylibre.com
|
|
There's no reason for this driver to be using OF-specific property
accessors. Switch to using generic device property interfaces and
replace the of.h include with property.h. This allows us to no longer
check the existence of the associated of_node.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007122350.75285-3-brgl@bgdev.pl
|
|
The line in nand_davinci_get_pdata() prototype is broken in a weird and
unreadable way. Make it consistent with the rest of the code.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007122350.75285-2-brgl@bgdev.pl
|
|
For better readability, put all includes in alphabetical order.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007122350.75285-1-brgl@bgdev.pl
|
|
There are no longer any users of the platform data for davinci rawnand
in board files. We can remove the public pdata headers and move the
structures that are still used into the driver compilation unit while
removing the rest.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240814122120.13975-1-brgl@bgdev.pl
|
|
Sometimes, writes fail because the tWB_max is not correctly observed
after sending PAGEPROG. It leads to the R/B pin to be read as in
the "ready" state right after sending the command, thus preventing the
normal tPROG delay to be actually observed. This happens because the
ndelay() that waits for tWB_max starts before the command reaches the
NAND chip.
Add a dummy read when a delay is requested at the end of the executed
instruction to make sure that the sent command is received by the NAND
before starting the short ndelay() (<1us but rounded up to 1us in
practice). This read is done on the control register area because
doing it on the Async Data area would change the NAND's RE pin state.
This is not perfect as the two areas are behind two different
devm_ioremap_resource() and could possibly be located on different
interconnects (I did not find more details). This means either the
additional latency due to the load operation is enough impacting, or it
has the expected behavior of ensuring the write has been received.
This has been tested on two platforms designed off of the
DAVINCI/OMAP-L138. The first uses a Toshiba NAND Flash (TC58NYG2S3EBAI5),
the other a Macronix one (MX30UF4G18AC).
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240308074609.9056-1-bastien.curutchet@bootlin.com
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230714174751.4060439-1-robh@kernel.org
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # atmel
Reviewed-by: Paul Cercueil <paul@crapouillou.net> # ingenic
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> # ingenic
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # intel
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # meson
Acked-by: Roger Quadros <rogerq@kernel.org> # omap_elm
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> # renesas
Reviewed-by: Heiko Stuebner <heiko@sntech.de> # rockchip
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> # sunxi
Acked-by: Thierry Reding <treding@nvidia.com> # tegra
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230411113816.3472237-1-u.kleine-koenig@pengutronix.de
|
|
Since core_chipsel is uint32_t, comparison to zero is redundant
Signed-off-by: Wang Weiyang <wangweiyang2@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220317113907.96006-1-wangweiyang2@huawei.com
|
|
Move the function nand_read_page_hwecc_oob_first() (previously
nand_davinci_read_page_hwecc_oob_first()) to nand_base.c, and export it
as a GPL symbol, so that it can be used by more modules.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-4-paul@crapouillou.net
|
|
The original comment that describes the function
nand_davinci_read_page_hwecc_oob_first() is very obscure and it is hard
to understand what it is for.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-3-paul@crapouillou.net
|
|
The function nand_davinci_read_page_hwecc_oob_first() first reads the
OOB data, extracts the ECC information, programs the ECC hardware before
reading the actual data in a loop.
Right after the OOB data was read, it called nand_read_page_op() to
reset the read cursor to the beginning of the page. This caused the
first page to be read twice: in that call, and later in the loop.
Address that issue by changing the call to nand_read_page_op() to
nand_change_read_column_op(), which will only reset the read cursor.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-2-paul@crapouillou.net
|
|
The function nand_davinci_read_page_hwecc_oob_first() does read the ECC
data from the OOB area. Therefore it does not need to calculate the ECC
as it is already available.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-1-paul@crapouillou.net
|
|
When the nand_chip structure is already available, there is no need to
dereference it through the info pointer. Use the chip pointer directly
in this case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113124045.32743-1-miquel.raynal@bootlin.com
|
|
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a5b ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-7-miquel.raynal@bootlin.com
|
|
No need to have our own in the raw NAND core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-18-miquel.raynal@bootlin.com
|
|
Mechanical switch from the legacy "mode" enumeration to the new
"engine type" enumeration in drivers and board files.
The device tree parsing is also updated to return the new enumeration
from the old strings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-11-miquel.raynal@bootlin.com
|
|
The use of "syndrome" placement should not be encoded in the ECC
engine mode/type.
Create a "placement" field in NAND chip and change all occurrences of
the NAND_ECC_HW_SYNDROME enumeration to be just NAND_ECC_HW and
possibly a placement entry like NAND_ECC_PLACEMENT_INTERLEAVED.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-10-miquel.raynal@bootlin.com
|
|
NAND_ECC_ is not a meaningful prefix, use NAND_ECC_ALGO_ instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-3-miquel.raynal@bootlin.com
|
|
This scheme has been introduced for the Davinci controller and means
that the OOB area must be read *before* the rest of the data. This has
nothing to do with the ECC in OOB placement as it could be understood
and most importantly, there is no point in having this function out of
the Davinci NAND controller driver. A DT property for this scheme has
been added but never used, even by the Davinci driver which only uses
this scheme to change the default nand_read_page().
Move the main read_page() helper into the Davinci driver and remove
the remaining boilerplate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200526195633.11543-4-miquel.raynal@bootlin.com
|
|
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-10-miquel.raynal@bootlin.com
|
|
Now that exec_op() is implemented we can get rid of the legacy interface
implementation.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200513172248.141402-4-boris.brezillon@collabora.com
|
|
Implement exec_op() so we can later get rid of the legacy interface
implementation.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200513172248.141402-3-boris.brezillon@collabora.com
|
|
We can use info->current_cs directly instead of doing this weird
IO_ADDR_{R,W} re-assignment dance.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200513172248.141402-2-boris.brezillon@collabora.com
|
|
Let's not rely on the dummy_controller embedded in nand_chip.legacy
and explicitly inherit from nand_controller instead.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200513172248.141402-1-boris.brezillon@collabora.com
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We try to force NAND controller drivers to properly separate the NAND
controller object from the NAND chip one, so let's deprecate the dummy
controller object embedded in nand_chip to encourage them to create
their own instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Now that the CS line to be selected is passed to ->exec_op() and
stored in chip->cur_cs and after patching all drivers implementing
->exec_op() to stop implementing this method, we can deprecate it by
moving it to the nand_legacy structure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The wait timeouts and delays are directly extracted from the NAND
timings and ->chip_delay is only used in legacy path, so let's move it
to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
All those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
We regularly have new NAND controller drivers that are making use of
fields/hooks that we want to get rid of but can't because of all the
legacy drivers that we might break if we do.
So, instead of removing those fields/hooks, let's move them to a
sub-struct which is clearly documented as deprecated.
We start with the ->IO_ADDR_{R,W] fields.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->dev_ready() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->cmd_ctrl() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->select_chip() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->write_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->read_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one.
Now is ecc->correct()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one.
Now is ecc->calculate()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one.
Now is ecc->hwctl()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers to
take a nand_chip object instead of an mtd_info one.
Now is nand_release()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers to take
a nand_chip object instead of an mtd_info one.
We start with nand_scan().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Also change the unused "struct device *dev" parameter of the driver
structure into a platform device to reuse it in the ->attach_chip()
hook.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
