| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD changes:
- Apart from a binding conversion to yaml, only minor changes/small
fixes have been merged.
Raw NAND changes:
- Minor fixes for various controller drivers like DMA mapping checks,
better timing derivations or bitflip statistics.
- some Hynix NAND flashes were not supporting read-retries, so don't
even try to do it
SPI NAND changes:
- In order to support high-speed modes, certain chips need extra
configuration like adding more dummy cycles. This is now possible,
especially on Winbond chips.
- Aside from that, Gigadevice gets support for a new chip (GD5F1GM9).
SPI NOR changes:
- A notable changes is the fix for exiting 4-byte addressing on
Infineon SEMPER flashes. These flashes do not support the standard
EX4B opcode (E9h), and use a vendor-specific opcode (B8h) instead.
- There is also a fix for unlocking flashes that are write-protected
at power-on. This was caused by using an uninitialized mtd_info in
spi_nor_try_unlock_all()"
* tag 'mtd/for-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (26 commits)
mtd: spinand: winbond: Add comment about the maximum frequency
mtd: spinand: winbond: Enable high-speed modes on w35n0xjw
mtd: spinand: winbond: Enable high-speed modes on w25n0xjw
mtd: spinand: Add a ->configure_chip() hook
mtd: spinand: Add a frequency field to all READ_FROM_CACHE variants
mtd: spinand: Fix macro alignment
spi: spi-mem: Take into account the actual maximum frequency
spi: spi-mem: Use picoseconds for calculating the op durations
mtd: rawnand: atmel: set pmecc data setup time
mtd: spinand: propagate spinand_wait() errors from spinand_write_page()
mtd: rawnand: fsmc: Add missing check after DMA map
mtd: rawnand: rockchip: Add missing check after DMA map
mtd: rawnand: hynix: don't try read-retry on SLC NANDs
mtd: rawnand: atmel: Fix dma_mapping_error() address
mtd: nand: brcmnand: fix mtd corrected bits stat
mtd: rawnand: renesas: Add missing check after DMA map
mtd: spinand: gigadevice: Add support for GD5F1GM9 chips
mtd: nand: brcmnand: replace manual string choices with standard helpers
mtd: map: Don't use "proxy" headers
mtd: spi-nor: Fix spi_nor_try_unlock_all()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
"UBIFS:
- No longer use write_cache_pages()
UBI:
- Remove an unused function"
* tag 'ubifs-for-linus-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: stop using write_cache_pages
mtd: ubi: Remove unused ubi_flush
|
|
* Raw NAND changes:
Various controller drivers received minor fixes like DMA mapping checks,
better timing derivations or bitflip statistics.
It has also been discovered that some Hynix NAND flashes were not
supporting read-retries, which is not properly supported.
* SPI NAND changes:
In order to support high-speed modes, certain chips need extra
configuration like adding more dummy cycles. This is now possible,
especially on Winbond chips.
Aside from that, Gigadevice gets support for a new chip (GD5F1GM9).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI NOR changes for 6.17
Notable changes:
- Fix exiting 4-byte addressing on Infineon SEMPER flashes. These
flashes do not support the standard EX4B opcode (E9h), and use a
vendor-specific opcode (B8h) instead.
- Fix unlocking of flashes that are write-protected at power-on. This
was caused by using an uninitialized mtd_info in
spi_nor_try_unlock_all().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Pull drm updates from Dave Airlie:
"Highlights:
- Intel xe enable Panthor Lake, started adding WildCat Lake
- amdgpu has a bunch of reset improvments along with the usual IP
updates
- msm got VM_BIND support which is important for vulkan sparse memory
- more drm_panic users
- gpusvm common code to handle a bunch of core SVM work outside
drivers.
Detail summary:
Changes outside drm subdirectory:
- 'shrink_shmem_memory()' for better shmem/hibernate interaction
- Rust support infrastructure:
- make ETIMEDOUT available
- add size constants up to SZ_2G
- add DMA coherent allocation bindings
- mtd driver for Intel GPU non-volatile storage
- i2c designware quirk for Intel xe
core:
- atomic helpers: tune enable/disable sequences
- add task info to wedge API
- refactor EDID quirks
- connector: move HDR sink to drm_display_info
- fourcc: half-float and 32-bit float formats
- mode_config: pass format info to simplify
dma-buf:
- heaps: Give CMA heap a stable name
ci:
- add device tree validation and kunit
displayport:
- change AUX DPCD access probe address
- add quirk for DPCD probe
- add panel replay definitions
- backlight control helpers
fbdev:
- make CONFIG_FIRMWARE_EDID available on all arches
fence:
- fix UAF issues
format-helper:
- improve tests
gpusvm:
- introduce devmem only flag for allocation
- add timeslicing support to GPU SVM
ttm:
- improve eviction
sched:
- tracing improvements
- kunit improvements
- memory leak fixes
- reset handling improvements
color mgmt:
- add hardware gamma LUT handling helpers
bridge:
- add destroy hook
- switch to reference counted drm_bridge allocations
- tc358767: convert to devm_drm_bridge_alloc
- improve CEC handling
panel:
- switch to reference counter drm_panel allocations
- fwnode panel lookup
- Huiling hl055fhv028c support
- Raspberry Pi 7" 720x1280 support
- edp: KDC KD116N3730A05, N160JCE-ELL CMN, N116BCJ-EAK
- simple: AUO P238HAN01
- st7701: Winstar wf40eswaa6mnn0
- visionox: rm69299-shift
- Renesas R61307, Renesas R69328 support
- DJN HX83112B
hdmi:
- add CEC handling
- YUV420 output support
xe:
- WildCat Lake support
- Enable PanthorLake by default
- mark BMG as SRIOV capable
- update firmware recommendations
- Expose media OA units
- aux-bux support for non-volatile memory
- MTD intel-dg driver for non-volatile memory
- Expose fan control and voltage regulator in sysfs
- restructure migration for multi-device
- Restore GuC submit UAF fix
- make GEM shrinker drm managed
- SRIOV VF Post-migration recovery of GGTT nodes
- W/A additions/reworks
- Prefetch support for svm ranges
- Don't allocate managed BO for each policy change
- HWMON fixes for BMG
- Create LRC BO without VM
- PCI ID updates
- make SLPC debugfs files optional
- rework eviction rejection of bound external BOs
- consolidate PAT programming logic for pre/post Xe2
- init changes for flicker-free boot
- Enable GuC Dynamic Inhibit Context switch
i915:
- drm_panic support for i915/xe
- initial flip queue off by default for LNL/PNL
- Wildcat Lake Display support
- Support for DSC fractional link bpp
- Support for simultaneous Panel Replay and Adaptive sync
- Support for PTL+ double buffer LUT
- initial PIPEDMC event handling
- drm_panel_follower support
- DPLL interface renames
- allocate struct intel_display dynamically
- flip queue preperation
- abstract DRAM detection better
- avoid GuC scheduling stalls
- remove DG1 force probe requirement
- fix MEI interrupt handler on RT kernels
- use backlight control helpers for eDP
- more shared display code refactoring
amdgpu:
- add userq slot to INFO ioctl
- SR-IOV hibernation support
- Suspend improvements
- Backlight improvements
- Use scaling for non-native eDP modes
- cleaner shader updates for GC 9.x
- Remove fence slab
- SDMA fw checks for userq support
- RAS updates
- DMCUB updates
- DP tunneling fixes
- Display idle D3 support
- Per queue reset improvements
- initial smartmux support
amdkfd:
- enable KFD on loongarch
- mtype fix for ext coherent system memory
radeon:
- CS validation additional GL extensions
- drop console lock during suspend/resume
- bump driver version
msm:
- VM BIND support
- CI: infrastructure updates
- UBWC single source of truth
- decouple GPU and KMS support
- DP: rework I/O accessors
- DPU: SM8750 support
- DSI: SM8750 support
- GPU: X1-45 support and speedbin support for X1-85
- MDSS: SM8750 support
nova:
- register! macro improvements
- DMA object abstraction
- VBIOS parser + fwsec lookup
- sysmem flush page support
- falcon: generic falcon boot code and HAL
- FWSEC-FRTS: fb setup and load/execute
ivpu:
- Add Wildcat Lake support
- Add turbo flag
ast:
- improve hardware generations implementation
imx:
- IMX8qxq Display Controller support
lima:
- Rockchip RK3528 GPU support
nouveau:
- fence handling cleanup
panfrost:
- MT8370 support
- bo labeling
- 64-bit register access
qaic:
- add RAS support
rockchip:
- convert inno_hdmi to a bridge
rz-du:
- add RZ/V2H(P) support
- MIPI-DSI DCS support
sitronix:
- ST7567 support
sun4i:
- add H616 support
tidss:
- add TI AM62L support
- AM65x OLDI bridge support
bochs:
- drm panic support
vkms:
- YUV and R* format support
- use faux device
vmwgfx:
- fence improvements
hyperv:
- move out of simple
- add drm_panic support"
* tag 'drm-next-2025-07-30' of https://gitlab.freedesktop.org/drm/kernel: (1479 commits)
drm/tidss: oldi: convert to devm_drm_bridge_alloc() API
drm/tidss: encoder: convert to devm_drm_bridge_alloc()
drm/amdgpu: move reset support type checks into the caller
drm/amdgpu/sdma7: re-emit unprocessed state on ring reset
drm/amdgpu/sdma6: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5.2: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5: re-emit unprocessed state on ring reset
drm/amdgpu/gfx12: re-emit unprocessed state on ring reset
drm/amdgpu/gfx11: re-emit unprocessed state on ring reset
drm/amdgpu/gfx10: re-emit unprocessed state on ring reset
drm/amdgpu/gfx9.4.3: re-emit unprocessed state on kcq reset
drm/amdgpu/gfx9: re-emit unprocessed state on kcq reset
drm/amdgpu: Add WARN_ON to the resource clear function
drm/amd/pm: Use cached metrics data on SMUv13.0.6
drm/amd/pm: Use cached data for min/max clocks
gpu: nova-core: fix bounds check in PmuLookupTableEntry::new
drm/amdgpu: Replace HQD terminology with slots naming
drm/amdgpu: Add user queue instance count in HW IP info
drm/amd/amdgpu: Add helper functions for isp buffers
drm/amd/amdgpu: Initialize swnode for ISP MFD device
...
|
|
Clarify that Winbond octal capable chips may be clocked at up to 166MHz,
which is their absolute maximum.
No per-operation maximum value (captured with a "0" in the table)
involves that in these cases the maximum frequency of the chip applies,
ie. the one commonly described in the DT.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
w35n0xjw chips can run at up to 166MHz in octal mode, but this is only
possible after programming various VCR registers.
Implement the new ->configure_chip() hook for this purpose.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
w25n0xjw chips have a high-speed capability hidden in a configuration
register. Once enabled, dual/quad SDR reads may be performed at a much
higher frequency.
Implement the new ->configure_chip() hook for this purpose and configure
the SR4 register accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
There is already a manufacturer hook, which is manufacturer specific but
not chip specific. We no longer have access to the actual NAND identity
at this stage so let's add a per-chip configuration hook to align the
chip configuration (if any) with the core's setting.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
These macros had initially no frequency field. When I added the "maximum
operation frequency" field, I did it initially on very common macros and
I decided to add an optional field for that (with VA_ARGS) in order to
prevent massively unreadable changes. I then added new variants in the
spinand.h header, and requested a frequency field for them by
default. Some times later, I also added maximum frequencies to other
existing variants, but I did it incorrectly, without noticing I was
wrong because the field was optional.
This mix is error prone, so let's do what I should have done since the
very beginning: add a frequency field to all READ_FROM_CACHE variants.
There is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
In order to pick the best variant, the duration of each typical
operation is derived and then compared. These durations are based on the
maximum capabilities of the chips, which are commonly the limiting
factors. However there are other possible limiting pieces, such as the
hardware layout, EMC considerations and in some cases, the SPI controller
itself.
We need to take this into account to further refine our variant choice,
so let's use the actual frequency that will be used for the operation
instead of the theoretical maximum.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
|
|
Setup the pmecc data setup time as 3 clock cycles for 133MHz as recommended
by the datasheet.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Reported-by: Zixun LI <admin@hifiphile.com>
Closes: https://lore.kernel.org/all/c015bb20-6a57-4f63-8102-34b3d83e0f5b@microchip.com
Suggested-by: Ada Couprie Diaz <ada.coupriediaz@arm.com>
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Since commit 3d1f08b032dc ("mtd: spinand: Use the external ECC engine
logic") the spinand_write_page() function ignores the errors returned
by spinand_wait(). Change the code to propagate those up to the stack
as it was done before the offending change.
Cc: stable@vger.kernel.org
Fixes: 3d1f08b032dc ("mtd: spinand: Use the external ECC engine logic")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The DMA map functions can fail and should be tested for errors.
Fixes: 4774fb0a48aa ("mtd: nand/fsmc: Add DMA support")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Rule: add
Link: https://lore.kernel.org/stable/20250702065806.20983-2-fourier.thomas%40gmail.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The DMA map functions can fail and should be tested for errors.
Fixes: 058e0e847d54 ("mtd: rawnand: rockchip: NFC driver for RK3308, RK2928 and others")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Some SLC NANDs like H27U4G8F2D expose a valid JEDEC ID yet they don't
support the read-retry mechanism, and fail.
Since SLC NANDs don't require read-retry, continue only if the bits per
cell is bigger than 1.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
It seems like what was intended is to test if the dma_map of the
previous line failed but the wrong dma address was passed.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Rule: add
Link: https://lore.kernel.org/stable/20250702064515.18145-2-fourier.thomas%40gmail.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Currently we attempt to get the amount of flipped bits from a hardware
location which is reset on every subpage. Instead obtain total flipped
bits stat from hardware accumulator. In addition identify the correct
maximum subpage corrected bits.
Signed-off-by: David Regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The DMA map functions can fail and should be tested for errors.
Fixes: d8701fe890ec ("mtd: rawnand: renesas: Add new NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
- GD5F1GM9UExxG (ID:c89101 3.3V)
- GD5F1GM9RExxG (ID:c88101 1.8V)
Both device feature:
- 1Gb density (1024 blocks)
- 2048-byte page size with 128-byte OOB
- 8-bit ECC requirement per 512 bytes
- Quad I/O Read support (opcode EBH)
- tPROG ≤ 300us typical page program time
Testing environment:
- Platform: Raspberry PI-5 (Linux raspberry 6.15.0-rc6-v8)
- Operations verified:
* Full device read/write/erase cycles on all blocks
* Nandspeed:
~ GD5F1GM9UE: 2.75MB/s read, 1.99MB/s write, 41.26MB/s erase
~ GD5F1GM9RE: 1.84MB/s read, 1.45MB/s write, 41.04MS/s erase
* Nandbiterrs: Both corredted 8-bit errors per 512 bytes
* Stresstest: Both 144k cycles 0 bad block growth
Full test log:
-U: https://gist.github.com/WT-886/b0f41fb50ddac3adc0020222c1f89b61
-R: https://gist.github.com/WT-886/8784e72f4632d519814928ff49225963
Datasheet:
-https://github.com/WT-886/DATASHEET/blob/main/GD5F1GM9-v1.0.pdf
Signed-off-by: Teng Wu <gigadevice2025@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Use kernel provided standard helper function to replace hard-coded
strings
Signed-off-by: Yuesong Li <liyuesong@vivo.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core updates from Danilo Krummrich:
"debugfs:
- Remove unneeded debugfs_file_{get,put}() instances
- Remove last remnants of debugfs_real_fops()
- Allow storing non-const void * in struct debugfs_inode_info::aux
sysfs:
- Switch back to attribute_group::bin_attrs (treewide)
- Switch back to bin_attribute::read()/write() (treewide)
- Constify internal references to 'struct bin_attribute'
Support cache-ids for device-tree systems:
- Add arch hook arch_compact_of_hwid()
- Use arch_compact_of_hwid() to compact MPIDR values on arm64
Rust:
- Device:
- Introduce CoreInternal device context (for bus internal methods)
- Provide generic drvdata accessors for bus devices
- Provide Driver::unbind() callbacks
- Use the infrastructure above for auxiliary, PCI and platform
- Implement Device::as_bound()
- Rename Device::as_ref() to Device::from_raw() (treewide)
- Implement fwnode and device property abstractions
- Implement example usage in the Rust platform sample driver
- Devres:
- Remove the inner reference count (Arc) and use pin-init instead
- Replace Devres::new_foreign_owned() with devres::register()
- Require T to be Send in Devres<T>
- Initialize the data kept inside a Devres last
- Provide an accessor for the Devres associated Device
- Device ID:
- Add support for ACPI device IDs and driver match tables
- Split up generic device ID infrastructure
- Use generic device ID infrastructure in net::phy
- DMA:
- Implement the dma::Device trait
- Add DMA mask accessors to dma::Device
- Implement dma::Device for PCI and platform devices
- Use DMA masks from the DMA sample module
- I/O:
- Implement abstraction for resource regions (struct resource)
- Implement resource-based ioremap() abstractions
- Provide platform device accessors for I/O (remap) requests
- Misc:
- Support fallible PinInit types in Revocable
- Implement Wrapper<T> for Opaque<T>
- Merge pin-init blanket dependencies (for Devres)
Misc:
- Fix OF node leak in auxiliary_device_create()
- Use util macros in device property iterators
- Improve kobject sample code
- Add device_link_test() for testing device link flags
- Fix typo in Documentation/ABI/testing/sysfs-kernel-address_bits
- Hint to prefer container_of_const() over container_of()"
* tag 'driver-core-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core: (84 commits)
rust: io: fix broken intra-doc links to `platform::Device`
rust: io: fix broken intra-doc link to missing `flags` module
rust: io: mem: enable IoRequest doc-tests
rust: platform: add resource accessors
rust: io: mem: add a generic iomem abstraction
rust: io: add resource abstraction
rust: samples: dma: set DMA mask
rust: platform: implement the `dma::Device` trait
rust: pci: implement the `dma::Device` trait
rust: dma: add DMA addressing capabilities
rust: dma: implement `dma::Device` trait
rust: net::phy Change module_phy_driver macro to use module_device_table macro
rust: net::phy represent DeviceId as transparent wrapper over mdio_device_id
rust: device_id: split out index support into a separate trait
device: rust: rename Device::as_ref() to Device::from_raw()
arm64: cacheinfo: Provide helper to compress MPIDR value into u32
cacheinfo: Add arch hook to compress CPU h/w id into 32 bits for cache-id
cacheinfo: Set cache 'id' based on DT data
container_of: Document container_of() is not to be used in new code
driver core: auxiliary bus: fix OF node leak
...
|
|
ubi_flush() was added in 2012 as part of
commit 62f384552b67 ("UBI: modify ubi_wl_flush function to clear work queue
for a lnum")
but has remained unused.
(It's friend ubi_wl_flush() is still used)
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Merge series from Heiko Schocher <hs@denx.de>:
This series introduces the changes needed for trivial spi
based sensors from ABB, currently operated from userspace.
|
|
Commit ff67592cbdfc ("mtd: spi-nor: Introduce spi_nor_set_mtd_info()")
moved all initialization of the mtd fields at the end of spi_nor_scan().
Normally, the mtd info is only needed for the mtd ops on the device,
with one exception: spi_nor_try_unlock_all(), which will also make use
of the mtd->size parameter. With that commit, the size will always be
zero because it is not initialized. Fix that by not using the size of
the mtd_info struct, but use the size from struct spi_nor_flash_parameter.
Fixes: ff67592cbdfc ("mtd: spi-nor: Introduce spi_nor_set_mtd_info()")
Cc: stable@vger.kernel.org
Reported-by: Jean-Marc Ranger <jmranger@hotmail.com>
Closes: https://lore.kernel.org/all/DM6PR06MB561177323DC5207E34AF2A06C547A@DM6PR06MB5611.namprd06.prod.outlook.com/
Tested-by: Jean-Marc Ranger <jmranger@hotmail.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250701140426.2355182-1-mwalle@kernel.org
|
|
Infineon SEMPER flash family does not support E9h opcode as Exit 4-byte
mode (EX4B). Therefore, params->set_4byte_addr_mode is not determined by
BFPT parse. Fixup it up by introducing vendor specific EX4B opcode (B8h)
and function.
Fixes: c87c9b11c53ce ("mtd: spi-nor: spansion: Determine current address mode")
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250612074427.22263-1-Takahiro.Kuwano@infineon.com
|
|
'struct spi_nor_fixups' are not modified in this driver.
Constifying these structures moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
23304 13168 0 36472 8e78 drivers/mtd/spi-nor/micron-st.o
After:
=====
text data bss dec hex filename
23560 12912 0 36472 8e78 drivers/mtd/spi-nor/micron-st.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/aa641732ba707ce3690217825c3ca7373ffde4f9.1748191985.git.christophe.jaillet@wanadoo.fr
|
|
Add defines for the values of the ECC_MODE field of the NAND_DEV0_ECC_CFG
register and change both the 'qcom-nandc' and 'spi-qpic-snand' drivers to
use those instead of magic numbers.
No functional changes. This is in preparation for adding 8 bit ECC strength
support for the 'spi-qpic-snand' driver.
Reviewed-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250702-qpic-snand-8bit-ecc-v2-1-ae2c17a30bb7@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The common QPIC code does not do any boundary checking when it handles
the command elements and scatter gater list arrays of a BAM transaction,
thus it allows to access out of bounds elements in those.
Although it is the responsibility of the given driver to allocate enough
space for all possible BAM transaction variations, however there can be
mistakes in the driver code which can lead to hidden memory corruption
issues which are hard to debug.
This kind of problem has been observed during testing the 'spi-qpic-snand'
driver. Although the driver has been fixed with a preceding patch, but it
still makes sense to reduce the chance of having such errors again later.
In order to prevent such errors, change the qcom_alloc_bam_transaction()
function to store the number of elements of the arrays in the
'bam_transaction' strucutre during allocation. Also, add sanity checks to
the qcom_prep_bam_dma_desc_{cmd,data}() functions to avoid using out of
bounds indices for the arrays.
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com> # on SDX75
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://patch.msgid.link/20250618-qpic-snand-avoid-mem-corruption-v3-2-319c71296cda@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Erase command is slow on discrete graphics storage
and may overshot PCI completion timeout.
BMG introduces the ability to have non-posted erase.
Add driver support for non-posted erase with polling
for erase completion.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Reuven Abliyev <reuven.abliyev@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://lore.kernel.org/r/20250617145159.3803852-9-alexander.usyskin@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
GSC NVM controller HW errors on quad access overlapping 1K border.
Align 64bit read and write to avoid readq/writeq over 1K border.
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://lore.kernel.org/r/20250617145159.3803852-6-alexander.usyskin@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Register the on-die nvm device with the mtd subsystem.
Refcount nvm object on _get and _put mtd callbacks.
For erase operation address and size should be 4K aligned.
For write operation address and size has to be 4bytes aligned.
CC: Rodrigo Vivi <rodrigo.vivi@intel.com>
CC: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Co-developed-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: Tomas Winkler <tomasw@gmail.com>
Co-developed-by: Vitaly Lubart <lubvital@gmail.com>
Signed-off-by: Vitaly Lubart <lubvital@gmail.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://lore.kernel.org/r/20250617145159.3803852-5-alexander.usyskin@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Implement read(), erase() and write() functions.
CC: Lucas De Marchi <lucas.demarchi@intel.com>
CC: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Co-developed-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: Tomas Winkler <tomasw@gmail.com>
Co-developed-by: Vitaly Lubart <lubvital@gmail.com>
Signed-off-by: Vitaly Lubart <lubvital@gmail.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://lore.kernel.org/r/20250617145159.3803852-4-alexander.usyskin@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
In intel-dg, there is no access to the spi controller,
the information is extracted from the descriptor region.
CC: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Co-developed-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://lore.kernel.org/r/20250617145159.3803852-3-alexander.usyskin@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Add auxiliary driver for intel discrete graphics
non-volatile memory device.
CC: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Co-developed-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://lore.kernel.org/r/20250617145159.3803852-2-alexander.usyskin@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
We need the driver-core fixes that are in 6.16-rc3 into here as well
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The expression '1 << EraseUnitSize' is evaluated in int, which causes
a negative result when shifting by 31 - the upper bound of the valid
range [10, 31], enforced by scan_header(). This leads to incorrect
extension when storing the result in 'erase->len' (uint64_t), producing
a large unexpected value.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Ivan Stepchenko <sid@itb.spb.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Memory allocated for the ECC engine conf is not released during spinand
cleanup. Below kmemleak trace is seen for this memory leak:
unreferenced object 0xffffff80064f00e0 (size 8):
comm "swapper/0", pid 1, jiffies 4294937458
hex dump (first 8 bytes):
00 00 00 00 00 00 00 00 ........
backtrace (crc 0):
kmemleak_alloc+0x30/0x40
__kmalloc_cache_noprof+0x208/0x3c0
spinand_ondie_ecc_init_ctx+0x114/0x200
nand_ecc_init_ctx+0x70/0xa8
nanddev_ecc_engine_init+0xec/0x27c
spinand_probe+0xa2c/0x1620
spi_mem_probe+0x130/0x21c
spi_probe+0xf0/0x170
really_probe+0x17c/0x6e8
__driver_probe_device+0x17c/0x21c
driver_probe_device+0x58/0x180
__device_attach_driver+0x15c/0x1f8
bus_for_each_drv+0xec/0x150
__device_attach+0x188/0x24c
device_initial_probe+0x10/0x20
bus_probe_device+0x11c/0x160
Fix the leak by calling nanddev_ecc_engine_cleanup() inside
spinand_cleanup().
Signed-off-by: Pablo Martin-Gomez <pmartin-gomez@freebox.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Dual and quad capable chips natively support dual and quad I/O variants
at up to 104MHz (1-2-2 and 1-4-4 operations). Reaching the maximum speed
of 166MHz is theoretically possible (while still unsupported in the
field) by adding a few more dummy cycles. Let's be accurate and clearly
state this limit.
Setting a maximum frequency implies adding the frequency parameter to
the macro, which is done using a variadic argument to avoid impacting
all the other drivers which already make use of this macro.
Fixes: 1ea808b4d15b ("mtd: spinand: winbond: Update the *JW chip definitions")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The default number of dummy cycles is 16 in octal I/O mode (1S-8S-8S),
and with this default configuration the maximum frequency is higher than
what is being advertised. There are higher and lower frequency
possibilities, which involve making changes in the number of dummy
cycles through the VCR register. At this stage, let's just describe the
default configuration correctly. There should be no functional change.
Fixes: 1ac5ff2f2ad6 ("mtd: spinand: winbond: Add octal support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
There's been a mistake when extracting the geometry of the W35N02 and
W35N04 chips from the datasheet. There is a single plane, however there
are respectively 2 and 4 LUNs. They are actually referred in the
datasheet as dies (equivalent of target), but as there is no die select
operation and the chips only feature a single configuration register for
the entire chip (instead of one per die), we can reasonably assume we
are talking about LUNs and not dies.
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Fixes: 25e08bf66660 ("mtd: spinand: winbond: Add support for W35N02JW and W35N04JW chips")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The idea behind this patch was to always let a "master" mtd device
available to anchor runtime PM. Historically, there was no mtd device
representing the whole storage as soon as partitions were coming into
play. The introduction of CONFIG_MTD_PARTITIONED_MASTER allowed to keep
this "master" device, but was not enabled by default to avoid breaking
existing users (otherwise the mtd device numbering would be totally
messed up with an off by 1, at least).
The approach of adding an mtd_master class on top of partitioned mtd
devices is breaking the mtd core in many creative ways, so better think
again this approach and revert the faulty changes for now.
This reverts commit 0aa7b390fc40a871267a2328bbbefca8b37ad307.
Fixes: 0aa7b390fc40 ("mtd: core: always create master device")
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The code in the ntfl write function is rather complex, and it contains
a 512 byte on-stack buffer. The combination of these two leads to using
more than the per-function stack warning limit in some configurations,
especially with KASAN enabled:
drivers/mtd/nftlcore.c:673:12: error: stack frame size (1328) exceeds limit (1280) in 'nftl_writeblock' [-Werror,-Wframe-larger-than]
Avoid this warning by moving the on-stack buffer into a separate function
that only copies one part of the device to another.
This does not really help with the total maximum stack usage in the
(non-KASAN) normal case, but it does two things:
- no single function has more than the warning limit
- the complexity goes down, so the parent function ends up
spilling few local variables, and the total actually goes
down slightly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The normal bin_attrs field can now handle const pointers.
This makes the _new variant unnecessary.
Switch all users back.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20250530-sysfs-const-bin_attr-final-v3-4-724bfcf05b99@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"A big core MTD change is the introduction of a new class to always
register a master device. This is a problem that has been there
forever: the "master" device was not always present depending on a
number of heuristics such as the presence of fixed partitions and the
absence of a Kconfig symbol to force its presence. This was a problem
for runtime PM operations which might not have the "master" device
available in all situation.
The SPI NAND subsystem has seen the introduction of DTR operations
(the equivalent of DDR transfers), which involved quite a few
preparation patches for clarifying macro names.
In the raw NAND subsystem, the brcmnand driver has been "fixed" for
old legacy SoCs with an update of the ->exec_op() hook, there has been
the introduction of a new controller driver named Loongson-1, and the
Qualcomm driver has received quite a few misc fixes as well as a new
compatible.
Finally, Macornix SPI NOR entries have been cleaned-up and some SFDP
table fixups for Macronix MX25L3255E have been merged.
Aside from this, there is the usual load of misc improvement, fixes,
and yaml conversion"
* tag 'mtd/for-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (42 commits)
mtd: rawnand: brcmnand: legacy exec_op implementation
mtd: rawnand: sunxi: Add randomizer configuration in sunxi_nfc_hw_ecc_write_chunk
mtd: nand: brcmnand: fix NAND timeout when accessing eMMC
mtd: nand: sunxi: Add randomizer configuration before randomizer enable
mtd: spinand: esmt: fix id code for F50D1G41LB
mtd: rawnand: brcmnand: remove unused parameters
mtd: core: always create master device
mtd: rawnand: loongson1: Fix inconsistent refcounting in ls1x_nand_chip_init()
mtd: rawnand: loongson1: Fix error code in ls1x_nand_dma_transfer()
mtd: rawnand: qcom: Fix read len for onfi param page
mtd: rawnand: qcom: Fix last codeword read in qcom_param_page_type_exec()
mtd: rawnand: qcom: Pass 18 bit offset from NANDc base to BAM base
dt-bindings: mtd: qcom,nandc: Document the SDX75 NAND controller
mtd: bcm47xxnflash: Add error handling for bcm47xxnflash_ops_bcm4706_ctl_cmd()
mtd: rawnand: Use non-hybrid PCI devres API
mtd: nand: ecc-mxic: Fix use of uninitialized variable ret
mtd: spinand: winbond: Add support for W35N02JW and W35N04JW chips
mtd: spinand: winbond: Add octal support
mtd: spinand: winbond: Add support for W35N01JW in single mode
mtd: spinand: winbond: Rename DTR variants
...
|
|
The SPI NAND subsystem has seen the introduction of DTR operations (the
equivalent of DDR transfers), which involved quite a few preparation
patches for clarifying macro names.
In the raw NAND subsystem, the brcmnand driver has been "fixed" for old
legacy SoCs with an update of the ->exec_op() hook, there has been the
introduction of a new controller driver named Loongson-1, and the
Qualcomm driver has received quite a few misc fixes as well as a new
compatible.
Aside from this, there is the usual load of misc improvement and fixes.
|
|
SPI NOR changes for 6.16
Notable changes:
- Cleanup some Macronix flash entries.
- Add SFDP table fixups for Macronix MX25L3255E.
|
|
Commit 3c8260ce7663 ("mtd: rawnand: brcmnand: exec_op implementation")
removed legacy interface functions, breaking < v5.0 controllers support.
In order to fix older controllers we need to add an alternative exec_op
implementation which doesn't rely on low level registers.
Fixes: 3c8260ce7663 ("mtd: rawnand: brcmnand: exec_op implementation")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
sunxi_nfc_hw_ecc_write_chunk
The function sunxi_nfc_hw_ecc_write_chunk() calls the
sunxi_nfc_hw_ecc_write_chunk(), but does not call the configuration
function sunxi_nfc_randomizer_config(). Consequently, the randomization
might not conduct correctly, which will affect the lifespan of NAND flash.
A proper implementation can be found in sunxi_nfc_hw_ecc_write_page_dma().
Add the sunxi_nfc_randomizer_config() to config randomizer.
Fixes: 4be4e03efc7f ("mtd: nand: sunxi: add randomizer support")
Cc: stable@vger.kernel.org # v4.6
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
