| Age | Commit message (Collapse) | Author |
|---|
|
Add function to configre LFPS sending for Panel Replay according to link
training sequence in HAS document.
This assumes we are using AUX Less always if it's supported by the sink and
the source.
v2:
- drop HAS reference
- replay kerneldoc comment with a generic comment
- check display version in intel_lnl_mac_transmit_lfps
Bspec: 68849
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://lore.kernel.org/r/20250526120512.1702815-11-jouni.hogander@intel.com
|
|
The dedicated display PHYs reset to a power state that blocks S0ix,
increasing idle system power. After a system reset (cold boot,
S3/4/5, warm reset) if a dedicated PHY is not being brought up
shortly, use these steps to move the PHY to the lowest power state
to save power.
1. Follow the PLL Enable Sequence, using any valid frequency such
as DP 1.62 GHz. This brings lanes out of reset and enables the
PLL to allow powerdown to be moved to the Disable state.
2. Follow PLL Disable Sequence. This moves powerdown to the Disable
state and disables the PLL.
v2: Rename WA function to more descriptive (Jani)
For PTL, only port A needs this wa
Add helpers to check presence of C10 phy and pll enabling (Imre)
v3: Rename wa function (Imre)
Check return value of C10 pll tables readout (Imre)
Use PLL request to check pll enabling (Imre)
v4: Move intel_cx0_pll_is_enabled() right after
intel_cx0_pll_disable() (Imre)
Add drm_WARN_ON() if C10 state cannot be calculated from
the tables (Imre)
v5: Add debug message on PLL enabling (Imre)
Add check for intel_encoder_is_dig_port() (Imre)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250218100019.740556-3-mika.kahola@intel.com
|
|
Try HDMI PLL alogorithm for C10 PHY, if there are no pre-computed tables.
Also get rid of the helpers to get rate for HDMI for C10/20 PHY, as we no
longer depend only on pre-computed tables.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250120042122.1029481-6-ankit.k.nautiyal@intel.com
|
|
struct intel_display will replace struct drm_i915_private as the main
device pointer for display code. Switch Cx0 PHY code over to it.
v2: Rebase, split out the include cleanups (Rodrigo)
v3: Rebase
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241029160822.800097-1-jani.nikula@intel.com
|
|
There's nothing in the header that requires the bit or bitfield
headers. Remove.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3e12f1d5ab17e501e4700044072fbb6dd9b2f459.1730146000.git.jani.nikula@intel.com
|
|
Currently, we may bump into pll mismatch errors during the
state verification stage. This happens when we try to use
fastset instead of full modeset. Hence, we would need to add
a check for pipe configuration to ensure that the sw and the
hw configuration will match. In case of hw and sw mismatch,
we would need to disable fastset and use full modeset instead.
v2: Fix C10 error on PLL comparison (BAT)
Use memcmp instead of fixed loops for pll config
comparison (Jani)
Clean up and use intel_cx0pll_dump_hw_state() to dump
pll information (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240523134649.31452-3-mika.kahola@intel.com
|
|
The intel_is_c10phy() is now unused. Remove.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/486ad2832c567ae491726c6c0cd7144e14469a2f.1710949619.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Add a number of encoder based functions to check if the port/phy of the
encoder is of a certain type, or to convert to phy or tc_port. Initially
these are just wrappers around the existing functions, but they can be
improved to use VBT data or use some cached info in the future.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7b2d350ee42883f2784030c649d16f983bd407bd.1710949619.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Add state verification for C20 as we have one
for C10.
V2: Use abstractation of HW readout (Gustavo)
Drop MPLLA/B from message for TX and CMN
parameters (Gustavo)
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com> (v1,v2)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231109112148.309669-1-mika.kahola@intel.com
|
|
As done with the hw readout, properly abstract the C10/C20 phy details
inside intel_cx0_phy.c.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231018222831.4132968-3-lucas.demarchi@intel.com
|
|
intel_cx0_phy.[ch] should contain the details about C10/C20, not leaking
it to the rest of the driver. Start abstracting this by exporting a
single PLL hw readout that handles the differences between C20 and C10
internally to that compilation unit.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231018222831.4132968-2-lucas.demarchi@intel.com
|
|
Passing in the atomic state + crtc state is a bit weird. The latter
can be just the crtc (which is the normal calling convention used
in a lot of other places).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231004155607.7719-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
State checkers should never modify the crtc states, so make
them const.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231004155607.7719-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Avoid including the world from headers when forward declarations
suffice.
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921155325.3851197-1-jani.nikula@intel.com
|
|
That function is not defined anywhere.
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Ravi Kumar Vodapalli <ravi.kumar.vodapalli@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230613214658.1099759-1-gustavo.sousa@intel.com
|
|
Add register writes to enable powering up Type-C subsystem i.e. TCSS.
For MeteorLake we need to request TCSS to power up and check the TCSS
power state after 500 us.
In addition, for PICA we need to set/clear the Type-C PHY ownnership
bit when Type-C device is connected/disconnected.
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-11-mika.kahola@intel.com
|
|
Readout hw state for Thunderbolt.
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-9-mika.kahola@intel.com
|
|
Enabling and disabling sequence for Thunderbolt PLL.
Bspec: 64568
v2: Use intel_de_wait_for_register() (RK)
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-8-mika.kahola@intel.com
|
|
Calculate port clock with C20 phy.
BSpec: 64568
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-5-mika.kahola@intel.com
|
|
As we already do with C10 chip, let's dump the pll
hw state for C20 as well.
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-4-mika.kahola@intel.com
|
|
Create a table for C20 DP1.4, DP2.0 and HDMI2.1 rates.
The PLL settings are based on table, not for algorithmic alternative.
For DP 1.4 only MPLLB is in use.
Once register settings are done, we read back C20 HW state.
BSpec: 64568
v2: Updated pll tables (RK)
MPLLB selection fix (RK)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-3-mika.kahola@intel.com
|
|
Like DG2, we still don't have a proper algorithm that can be used
for calculating PHY settings, but we do have tables of register
values for a handful of the more common link rates. Some support is
better than none, so let's go ahead and add/use these tables when we
can, and also add some logic to hdmi_port_clock_valid() to filter the
modelist to just the modes we can actually support with these link
rates.
Hopefully we'll have a proper / non-encumbered algorithm to calculate
these registers by the time we upstream and we'll be able to replace
this patch with something more general purpose.
Bspec: 64568
v2: Rebasing with Clint's HDMI C10 PLL tables (Mika)
v3: Remove the extra hdmi clock check pruning.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-8-radhakrishna.sripada@intel.com
|
|
C10 phys uses direct mapping internally for voltage and pre-emphasis levels.
Program the levels directly to the fields in the VDR Registers.
Bspec: 65449
v2: From table "C10: Tx EQ settings for DP 1.4x" it shows level 1
and preemphasis 1 instead of two times of level 1 preemphasis 0.
Fix this in the driver code as well.
v3: VSwing update (Clint)
v4: Add vboost termination ctl programming(Imre)
Fix tx llogic and other nits
Restrict C10 vdr ctl register access for C10 phy(RK)
v5: Program vboots, termination ctl for both lanes(Imre)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>(v3)
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-5-radhakrishna.sripada@intel.com
|
|
XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy
has a dedicated PIPE 5.2 Message bus for configuration. This message
bus is used to configure the phy internal registers.
XELPDP has C10 phys to drive output to the EDP and the native output
from the display engine. Add structures, programming hardware state
readout logic. Port clock calculations are similar to DG2. Use the DG2
formulae to calculate the port clock but use the relevant pll signals.
Note: PHY lane 0 is always used for PLL programming.
Add sequences for C10 phy enable/disable phy lane reset,
powerdown change sequence and phy lane programming.
Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636
v2: Squash patches related to C10 phy message bus and pll
programming support (Jani)
Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani)
Move macro definitions (Jani)
DP rates as separate patch (Jani)
Spin out xelpdp register definitions into a separate file (Jani)
Replace macro to select registers based on phy lane with
function calls (Jani)
Fix styling issues (Jani)
Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas)
v3: Move clear request flag into try-loop
v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani)
use __intel_de_wait_for_register() instead of __intel_wait_for_register
and uncomment intel_uncore.h (Jani)
Add DP-alt support for PHY lane programming (Khaled)
v4: Add tx and cmn on c10mpllb_state (Imre)
Add missing waits for pending transactions between two message bus
writes (Imre)
General cleanups and simplifications (Imre)
v5: Few nit cleanups from rev4 (imre)
s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK)
Rebase
v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function
Fix typo in comment for REG_FIELD_PREP8 definition(Imre)
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v4)
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
|
