summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2005-08-01[PATCH] v4l: bug fix to correct tea5767 autodetectionMauro Carvalho Chehab
This patch does correct radio chip autodetection to avoid misdetecting mt20xx microtune as tea5767 chip. Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-01[PATCH] aacraid: Fix for controller load based timeoutsMark Haverkamp
Martin Drab found that he could get aacraid timeouts with high load on his controller / disk drive combinations. After some experimentation Mark Salyzyn has come up with a patch to reduce the default max_sectors to something that will keep the controller from being overloaded and will eliminate the timeout issues. Signed-off-by: Mark Haverkamp <markh@osdl.org> Cc: James Bottomley <James.Bottomley@steeleye.com> Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-01[PATCH] silence cs89x0Denis Vlasenko
cs89x0 talks a lot at boot. Seems like debug leftover. This patch downgrades printks to KERN_DEBUG. While we're at it, make these messages a bit less obscure. Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-01[PATCH] md: make sure raid5/raid6 resync uses correct 'max_sectors'NeilBrown
The default resync_max_sector is set to "mddev->size << 1". If the raid-personality-module updates mddev->size, it must update resync_max_sectors too. Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-01[PATCH] v4l: cx88 card support and documentation finishing touchesMichael Krufky
Peter Missel: - Add support for the SVideo input on the GDI Black Gold. Mauro Carvalho Chehab: - Linux/version.h removed. Replaced by linux/utsname.h Michael Krufky: - Added analog support for DViCO FusionHDTV5 Gold. CC: Peter Missel <peter.missel@onlinehome.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br> Signed-off-by: Michael Krufky <mkrufky@m1k.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-01[PATCH] V4L: Miscellaneous fixesMauro Carvalho Chehab
- Fixed some bttv card numbers. - BTTV and SAA7134 version numbers incremented to reflect changes. - pci_dma_supported() is called after pci_set_dma_mask() which already did check that for us. This patch removes the unneeded call to pci_dma_supported() at bttv-driver.c - Ensure a sufficient I2C bus idle time between 2 messages for saa7134-i2c.c - It is important to write at first to MO_GP3_IO for cx88-tvaudio.c - Use try_to_freeze() instead of refrigerator at msp3400.c - Recognizing the MFPE05-2 Tuner at tveeprom.c - Add new parameter to help identify radio chipsets at tuner module: show_i2c=1 will show 16 reading bytes from detected tuners. - BTTV does generate some Unimplemented IOCTL log at tuner module: 0x40046d11(dir=1,tp=0x6d,nr=17,sz=4) means that it is sending MSP3400 calls to non-msp3400 tuners. Warning eliminated. VIDIOSAUDIO is also called, so debug messages updated. It is still requiring IOCTL implementation. - Added two more tuners. - Add support for the SVideo input on the GDI Black Gold. Signed-off-by: Peter Missel <peter.missel@onlinehome.de> Signed-off-by: Graham Bevan <graham.bevan@ntlworld.com> Signed-off-by: Torsten Seeboth <Torsten.Seeboth@t-online.de> Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t.online.de> Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch> Signed-off-by: Michael Krufky <mkrufky@m1k.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-01[PATCH] skge build fixAndrew Morton
Make it compile with CONFIG_PM=n Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-01[PATCH] i2c-mpc.c: revert duplicate patchAndrew Morton
Seems that both Greg and I submitted the same patch and it just kept on applying... Cc: Greg KH <greg@kroah.com> Cc: Kumar Gala <galak@freescale.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-01Revert ACPI interrupt resume changesLinus Torvalds
If there are devices that use interrupts over a suspend event, ACPI must restore the PCI interrupt links on resume. Anything else breaks any device that hasn't been converted to the new (dubious) PM rules. Drivers that need the irq free/re-aquire sequence can be done one by one independently of this one.
2005-08-01[PATCH] tridentfb: Fix scrolling artifacts during disk IOAntonino A. Daplas
Reported by: Jochen Hein (Bugzilla Bug 4312) When there is disk I/O happening, the framebuffer has a little snow on the screen. Once I/O has finished, no garbage remains on screen. This bug was explained by: Knut Petersen Most important is CRTC register 2f, signal quality is also improved for higher vclk values by changing set_vclk() according to the X drivers and cyblafb.c The fix is to set the performance register (0x2f) with a more stable value. Signed-off-by: Antonino Daplas <adaplas@pol.net> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-01[PATCH] tridentfb: Fix scrolling artifacts if acceleration is enabledAntonino A. Daplas
Reported by: Jochen Hein (Bugzilla Bug 4386) booting leaves the end of long lines in the last line on screen when scrolling. When X is running, scrolling puts garbage on the screen (looks like X data) Console switch fixes the screen. Behaviour seems to be identical with noaccel and without on the video=tridentfb parameter in lilo.conf. This bug was explained by: Knut_Petersen Acceleration is broken for all BLADE 3D chips for all versions of kernel 2.6 except for 32bit modes. Most important reason is that the u32 col parameter of the graphics engine needs the color value replicated to all u8 of the u32 (8bit modes) and to both u16 of the u32. Fix color value passed to graphics engine, verified by the reporter. Signed-off-by: Antonino Daplas <adaplas@pol.net> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-01[PATCH] pcmcia: fix multiple insertion of multifunction cardsDominik Brodowski
The ordering of setting and clearing device_add_pending went wrong on some occasions, causing multifunction cards only to be handled correctly on the first insertion, not on subsequent ones. Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-01[PATCH] pcmcia: defer ide-cs initialization after other IDE drivers started upDominik Brodowski
Avoid registering PCMCIA CF cards before other IDE stuff. This means the risk of /dev/hd* being re-ordered is lessened. The _sane_ thing to assert any ordering is to use udev, nameif and so on, of course. Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-31Merge head 'upstream-fixes' of ↵Linus Torvalds
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
2005-07-31Merge head 'upstream-fixes' of ↵Linus Torvalds
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
2005-07-31[PATCH] Display name of fbdev deviceJames Simmons
This patch displays the name of the fbdev driver in sysfs. Down the road this will replace the current proc handle we have. Signed-off-by: James Simmons <jsimmons@infradead.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-31[PATCH] SMP fix for 6pack driverRalf Baechle
Drivers really only work well in SMP if they actually can be selected. This is a leftover from the time when the 6pack drive only used to be a bitrotten variant of the slip driver. Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org> Kconfig | 2 +- 1 files changed, 1 insertion(+), 1 deletion(-) Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-31[PATCH] Fix OMAP specific typo in smc91x.hTony Lindgren
--ReaqsoxgOBHFXBhH Content-Type: text/plain; charset=us-ascii Content-Disposition: inline Hi Jeff, Here's a little patch fixing a typo in smc91x.h. Regards, Tony --ReaqsoxgOBHFXBhH Content-Type: text/x-chdr; charset=us-ascii Content-Disposition: inline; filename="patch-fix-typo-smc91x.h" Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-31[PATCH] sk98lin: fix workaround for yukon-lite chipset (> rev 7)Stephen Hemminger
Yukon-Lite chipset needs workaround for revision 7 (or later). Without this patch, chip gets stuck in low power mode and never boots. Newer SysKonnect vendor code already had same patch. Related bug in skge is http://bugs.gentoo.org/87822 Chris, please add for 2.6.12.2 Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-31[PATCH] SCSI_SATA has to be a tristateAdrian Bunk
SCSI=m must disallow static drivers. The problem is that all the SATA drivers depend on SCSI_SATA. With SCSI=m and SCSI_SATA=y this allows the static enabling of the SATA drivers with unwanted effects, e.g.: - SCSI=m, SCSI_SATA=y, SCSI_ATA_ADMA=y -> SCSI_ATA_ADMA is built statically but scsi/built-in.o is not linked into the kernel - SCSI=m, SCSI_SATA=y, SCSI_ATA_ADMA=y, SCSI_SATA_AHCI=m -> SCSI_ATA_ADMA and libata are built statically but scsi/built-in.o is not linked into the kernel, SCSI_SATA_AHCI is built modular (unresolved symbols due to missing libata) Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-31[PATCH] skge: version 0.8Stephen Hemminger
Increase driver version to 0.8 Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-31[PATCH] skge: led toggle cleanupStephen Hemminger
Cleanup code that is used to toggle LED's. Since we get called from ethtool, can use that thread rather than setting up a timer. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-31[PATCH] skge: ignore phy interrupts during negotiationStephen Hemminger
During autonegotiation set PHY interrupt mask to ignore bogus speed change interrupts. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-31[PATCH] skge: fifo control register access fixStephen Hemminger
The code to clear fifo errors was incorrect and sending garbage to the external phy. Removed the no longer used inline's funcs. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-31[PATCH] skge: whitespace fixesStephen Hemminger
Minor whitespace cleanups. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-31[PATCH] skge: support yukon lite rev 4Stephen Hemminger
The check for Yukon lite changes was restricting itself to rev A3. It turns out that these changes are also true on A4 and later. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-31[PATCH] skge: phy lock deadlockStephen Hemminger
Cleanup the phy_lock deadlock because of relocking in the nway_reset path. Reported by Francois Romieu. Also, don't need to do irqsave/restore for blink, just excluding bh is good enough. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-31[PATCH] skge: disable tranmitter on shutdownStephen Hemminger
Here is a fix for a typo, thanks Eliot Dresselhaus. Since transmitter not active when device is down, it wasn't really noticed. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-31[PATCH] skge: remove SK-9EE supportStephen Hemminger
The SK-9E boards use the Marvell Yukon2 chipset which is not supported by the skge driver. Thanks to Ralph Roesler for noticing. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-31[PATCH] skge: silence mac data parity messagesStephen Hemminger
Using Genesis board, I get harmless error reports. Rather than console error, turn it into a error counter. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-30Revert "yenta free_irq on suspend"Linus Torvalds
ACPI is wrong. Devices should not release their IRQ's on suspend and re-aquire them on resume. ACPI should just re-init the IRQ controller instead of breaking most drivers very subtly. Breakage reported by Hugh Dickins <hugh@veritas.com> Undo: d8c4b4195c7d664baf296818bf756775149232d3 Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-30[PATCH] sk98lin: basic suspend/resume support fixesRafael J. Wysocki
An early version of the sk98lin patch was merged via Len's tree. But there were subsequent updates as a result of review from Jeff. THis fixes things up. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Jeff Garzik <jgarzik@pobox.com> Cc: "Brown, Len" <len.brown@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-30merge 2.6.13-rc4 with ACPI's to-linus treeLen Brown
2005-07-29/home/lenb/src/to-linus branch 'acpi-2.6.12'Len Brown
2005-07-29[ACPI] suspend/resume ACPI PCI Interrupt LinksDavid Shaohua Li
Add reference count and disable ACPI PCI Interrupt Link when no device still uses it. Warn when drivers have not released Link at suspend time. http://bugzilla.kernel.org/show_bug.cgi?id=3469 Signed-off-by: David Shaohua Li <shaohua.li@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2005-07-29[ACPI] delete boot-time printk()s from processor_idle.cVenkatesh Pallipadi
http://bugzilla.kernel.org/show_bug.cgi?id=4401 Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2005-07-29[ACPI] fix resume issues on Asus L5DRafael J. Wysocki
http://bugzilla.kernel.org/show_bug.cgi?id=4416 Signed-off-by: Rafael J. Wysocki <rjwysocki@sisk.pl> Signed-off-by: Len Brown <len.brown@intel.com>
2005-07-29[ACPI] Add "ec_polling" boot optionLuming Yu
EC burst mode benefits many machines, some of them significantly. However, our current implementation fails on some machines such as Rafael's Asus L5D. This patch restores the alternative EC polling code, which can be enabled at boot time via "ec_polling" http://bugzilla.kernel.org/show_bug.cgi?id=4665 Signed-off-by: Luming Yu <luming.yu@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2005-07-29[ACPI] address boot-freeze with updated DMI blacklist for c-statesDavid Shaohua Li
http://bugzilla.kernel.org/show_bug.cgi?id=4763 Signed-off-by: David Shaohua Li <shaohua.li@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2005-07-29[PATCH] agp: restore APBASE after setting APSIZEMatthew Garrett
When leaving S3 state, the AGP bridge may not have all PCI configuration registers set in the same way as they were at boot. This should be fixed by pci_restore_state - however, the APBASE register cannot be set to conflict with the APSIZE register. If APSIZE is larger than it was before suspend, pci_restore_state will not restore APBASE correctly. The attached patch adds an extra item to the agp_bridge_data structure and uses it to store the value of APBASE. On resume, this is then written after APSIZE has been set. This patch only touches the path used for Intel chipsets without integrated graphics, and may need to be extended to work with the others. Without this patch, I get the symptoms described in bug 4921 - APBASE ends up overlapping various PCI devices, and as a result they fail to work after resume. Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org> Acked-by: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-29[PATCH] s390: device recognitionCornelia Huck
Close a small window where a device may be not operational again after senseid finished and the "same device" check fails due to dev=0000 by checking for dnv after stsch() by then setting the device to not operational. (No need to check for dnv in ccw_device_handle_oper() again since we don't do stsch() into the subchannel's schib in the meantime and will get a crw anyway if the device becomes not oper again). Signed-off-by: Cornelia Huck <cohuck@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-29[PATCH] fbdev: Replace memcpy with for-loop when preparing bitmapAntonino A. Daplas
Do not use memcpy in fb_pad_aligned_buffer. It is suboptimal because only a few bytes are moved at a time. Replace with a for-loop. Signed-off-by: Antonino Daplas <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-29[PATCH] vesafb: Fix mtrr bugsAntonino A. Daplas
>> vesafb: mode is 800x600x16, linelength=1600, pages=16 >> vesafb: scrolling: redraw >> vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 >> mtrr: type mismatch for fc000000,1000000 old: write-back new: write- >> combining Range is already set to write-back, vesafb attempts to add a write-combining mtrr (default for vesafb). >> mtrr: size and base must be multiples of 4 kiB This is a bug, vesafb attempts to add a size < PAGE_SIZE triggering the messages below. To eliminate the warning messages, you can add the option mtrr:2 to add a write-back mtrr for vesafb. Or just use nomtrr option. 1. Fix algorithm for finding the best power of 2 size with mtrr_add(). 2. Add option to choose the mtrr type by extending the mtrr boot option: mtrr:n where n 0 = no mtrr (equivalent to using the nomtrr option) 1 = uncachable 2 = write back 3 = write combining (default) 4 = write through Signed-off-by: Antonino Daplas <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-29[PATCH] serial: add MMIO support to 8250_pnpBjorn Helgaas
Add support for UARTs in MMIO space and clean up a little whitespace. HP legacy-free ia64 machines need this. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-29[PATCH] USB: hidinput_hid_event() oops fixPete Zaitcev
It seems that I see a bug in hidinput_hid_event. The check for NULL can never work, becaue &hidinput->input is nonzero at all times. Cc: <vojtech@suse.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-29[PATCH] USB: fix in usb_calc_bus_timeDan Streetman
This patch does the same swap, i.e. use the ISO macro if (isoc). Additionally, it fixes the return value - the usb_calc_bus_time function returns the time in nanoseconds (I didn't notice that before) while the HS_USECS and HS_USECS_ISO are microseconds. This fixes the function to return nanoseconds always, and adjusts ehci-q.c (the only high-speed caller of the function) to wrap the call in NS_TO_US(). Signed-off-by: Dan Streetman <ddstreet@ieee.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-29[PATCH] USB: fix Bug in usb-skeleton.cConger, Chris A
Compare endpoint address to USB_ENDPOINT_DIR_MASK to determine endpoint direction... From: "Conger, Chris A." <CHRIS.A.CONGER@saic.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-29[PATCH] USB: add S3C24XX USB Host driver supportBen Dooks
USB (OHCI) Host driver for S3C2410/S3C2440 based systems Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-29[PATCH] USB: drivers/net/usb/zd1201.c: Gigabyte GN-WLBZ201 dongle usbidMathieu
Gigabyte GN-WLBZ201 wifi usb dongle works very well, using the zd1201 driver. the only missing part is that the corresponding usbid is not declared. The following patch should fix this. From: "Mathieu" <matt@minas-morgul.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-29[PATCH] USB: Patch for KYOCERA AH-K3001V supportMasahito Omote
This patch enables a support of KYOCERA AH-K3001V, one of the most popular cell phone in Japan. This device has vendor specific ID but works with acm driver by adding USB ID. This device already works on FreeBSD and OS X by native USB ACM driver with USB ID added. This device is probed as NO_UNION_NORMAL not to hang up when probing. Signed-off-by: Masahito Omote <omote@utyuuzin.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-05-29 09:54:38 +0000