summaryrefslogtreecommitdiff
path: root/drivers/net/ixgbe/ixgbe_phy.c
AgeCommit message (Collapse)Author
2011-08-10intel: Move the Intel wired LAN driversJeff Kirsher
Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and the necessary Kconfig and Makefile changes. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-08-04intel drivers: repair missing flush operationsJesse Brandeburg
after review of all intel drivers, found several instances where drivers had the incorrect pattern of: memory mapped write(); delay(); which should always be: memory mapped write(); write flush(); /* aka memory mapped read */ delay(); explanation: The reason for including the flush is that writes can be held (posted) in PCI/PCIe bridges, but the read always has to complete synchronously and therefore has to flush all pending writes to a device. If a write is held and followed by a delay, the delay means nothing because the write may not have reached hardware (maybe even not until the next read) Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-05-04ixgbe: Use function pointer for ixgbe_acquire/release_swfw_sync()Emil Tantilov
Change remaining direct calls to function pointers. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Evan Swanson <evan.swanson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-04-27ixgbe: explicitly disable 100H for x540Emil Tantilov
100H is not supported on this HW, but the bit is set on the PHY. This can result in link at 100F when advertising only 1000F. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Evan Swanson <evan.swanson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-04-13ixgbe: explicitly disable 100H for x540Emil Tantilov
100H is not supported on this HW, but the bit is set on the PHY. This can result in link at 100F when advertising only 1000F. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Evan Swanson <evan.swanson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-04-13ixgbe: cleanup short msleep's (<20ms) to use usleep_rangeDon Skidmore
Since msleep might not sleep for the desired amount when less than 20ms use usleep_range. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-31Fix common misspellingsLucas De Marchi
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-12ixgbe: update PHY code to support 100Mbps as well as 1G/10GEmil Tantilov
This change updates the PHY setup code to support 100Mbps capable PHYs as well as 10G and 1Gbps. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07ixgbe: cleanup PHY initEmil Tantilov
This change cleans up several situations in which we were either stepping over possible errors, or calling initialization routines multiple times. Also includes whitespace fixes where applicable. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-03ixgbe: cleanup copyright string for 2011Don Skidmore
Updating the copyrights for 2011 as well as make the ixgbe_copyright string a constant. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-03ixgbe: add function pointer for semaphore functionDon Skidmore
The X540 devices grabs semaphores differently than 82599 and 82598 devices do. They do however also grab them in allot of the same functions. So I'm adding a new MAC operation function pointer to allow us to use the correct function based on our MAC type. I'm also changing all the semaphore calls to use this new function pointer. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-03ixgbe: cleanup handling of I2C interface to PHYEmil Tantilov
The I2C interface was not being correctly locked down per port. As such this can lead to race conditions that can cause issues. This patch cleans up the handling to make certain we are not experiencing racy I2C access. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-03ixgbe: add polling test to end of PHY resetEmil Tantilov
Some PHYs require that we poll the reset bit and wait for it to clear before continuing initialization. As such we should add this check to the end of the ixgbe_reset_phy_generic routine. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-03ixgbe: cleanup code in ixgbe_identify_sfp_module_genericEmil Tantilov
This change cleans up several issues in ixgbe_identify_sfp_module_generic including whitespace, redundant code, I2C EEPROM reads without exception handling, and an if/elseif/else without braces. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10ixgbe: fix X540 phy id to correct valueDon Skidmore
The existing PHY ID for X540 was from early production hardware and is no longer correct. This patch corrects that. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-11-16ixgbe: add MAC and PHY support for x540Don Skidmore
Adds the new x540.c file and Aquantia 1202 PHY for X540 support. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-11-16ixgbe: make silicon specific functions genericDon Skidmore
The new MAC type X540 shares much of the same functionality of some silicon specific functions. To reduce duplicate code, made these functions generic. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-06-30ixgbe: add 1g PHY support for 82599Don Skidmore
Add support for 1G SFP+ PHY's to 82599. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-16ixgbe: add comment on SFP+ ID for Active DADon Skidmore
These comments were forgotten in the initial patch to add this functionality. This patch corrects that. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-20ixgbe:add support for a new 82599 10G Base-T deviceMallikarjuna R Chilakala
This adds support for a new copper device for 82599, device id 0x151c. This 82599 10GBase-T device uses the PHY's internal temperature sensor to guard against over-temp conditions. In this scenario the PHY will be put in a low power mode and link will no longer be able to transmit or receive any data. When this occurs, the over-temp interrupt is latched and driver logs this error message. A HW reset or power cycle is required to clear this status. Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18ixgbe: add support for active DA cablesDon Skidmore
This patch adds support of active DA cables. This is renaming and adding some PHY type enumerations. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-24net/intel: remove trailing space in messagesFrans Pop
Includes one minor indentation fix to placate checkpatch. Signed-off-by: Frans Pop <elendil@planet.nl> Cc: e1000-devel@lists.sourceforge.net Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-13ixgbe: update copyright datesShannon Nelson
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03ixgbe: fix issues with failing to detect insert of unsupported moduleDon Skidmore
Several small fixes around negative test case of the insertion of a IXGBE_ERR_NOT_SUPPORTED module. - mdio45_probe call was always failing due to mdio.prtad not being set. The function set to mdio.mdio_read was still working as we just happen to always be at prtad == 0. This will allow us to set the phy_id and phy.type correctly now. - There was timing issue with i2c calls when initiated from a tasklet. A small delay was added to allow the electrical oscillation to calm down. - Logic change in ixgbe_sfp_task that allows NOT_SUPPORTED condition to be recognized. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07ixgbe: Harden the 82599 multispeed fiber autotry mechanismPeter P Waskiewicz Jr
82599 supports multispeed fiber optical modules (10Gbps/1Gbps). Some scenarios can cause the autotry mechanism to not negotiate link properly. What needs to happen is the driver must flap the Tx laser to induce an Rx Loss of Signal on the link partner. This will restart the autotry mechanism to get link into a known state. The software definable pin (SDP) 3 on the 0x10fb NIC is wired to cause a Tx LOS event, which triggers the Rx LOS we require. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-26ixgbe: fix 82598 SFP initialization after driver load.Don Skidmore
If we loaded the driver with out a SFP module plugged in it would leave it in a state that make it later unable to link when a module was plugged in. This patch corrects that by: ixgbe_probe() - moving the check for IXGBE_ERR_SFP_NOT_PRESENT from after get_invariants() to after reset_hw() as now reset_hw() is where this condition will be indentified. ixgbe_reset_hw_82598() - Enable this function to now return IXGBE_ERR_SFP_NOT_PRESENT. ixgbe_identify_sfp_module_generic() - This where the lack of SFP module is detected. Modifications are added to allow a different return value for modules that just haven't been plugged in yet. Other functions were updated to allow correct logging. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-19ixgbe: Change Direct Attach Twinax cable detection for SFP+ NICsPeter P Waskiewicz Jr
The SFF specification for Direct Attach cable detection has now been ratified. Previously, DA cable detect was looking at the Twinaxial bit in byte 9 of the SFP+ EEPROM. The spec now defines active and passive DA cables in byte 8 of the SFP+ EEPROM. This patch changes the cable detection for both 82598 and 82599 SFP+ adapters to conform to the new spec. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-29ixgbe: Use generic MDIO definitions and functionsBen Hutchings
Compile-tested only. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-27ixgbe: Disallow SFP 1G modules in the SFP+ cages for 82598 and 82599Waskiewicz Jr, Peter P
82598 and 82599 do not support SFP 1G modules. Instead of allowing the driver to load, but never get link, rejecting the module and displaying a useful message is more preferrable. The framework for displaying the failure message already exists, now we just need to detect and reject the SFP modules. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11ixgbe: Update get_physical_layer() calls, plus a version bumpPeter P Waskiewicz Jr
Not all physical connection types are being correctly identified. This fixes that issue, and cleans up the logic to make it more maintainable. Also clean up the code for device capabilities from the EEPROM to support multiple SKUs of the same hardware. Bump the version to reflect all the updates since the 82599 merge. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11ixgbe: Remove unnecessary PHY reset, properly identify multispeed fiber modulesPJ Waskiewicz
This patch does two things: 1) On 82599, the PHY is emedded in the MAC. On 82598, the SFP+ NIC has an external PHY. The reset in the SFP+ setup patch for 82598 is unnecessary on 82599, and adds extra dead time to device initialization. This removes that PHY reset for 82599 only. 2) On 82599, the SFP+ modules are multispeed fiber modules (10G/1G). We need to make sure to identify them properly for the remaining init sections to properly set them up. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-01ixgbe: Add hardware specific initialization code for 82599 devicesPJ Waskiewicz
This patch adds the hardware initialization code specific to 82599. This is similar to the 82598 hardware initialization code. It also includes all changes to the existing hardware init code to support 82599. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-01ixgbe: Update copyright dates, bump the driver version numberPeter P Waskiewicz Jr
New year, new copyright date ranges. Also bump the driver version number to reflect many of the recent changes. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20ixgbe: add SFP+ driver supportDonald Skidmore
This patch adds support for SFP+ PHY in the following device ID's (10DB, 10F1, 10E1). These SFP+ PHY's are accessed via an I2C interface so the patch also includes functions to support this. Another feature of note is that the PHY is pluggable and some rearchitecting was needed to support this. Signed-off-by: Donald Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-02ixgbe: add device support for 82598AT (copper 10GbE) adaptersJesse Brandeburg
Intel is currently shipping support for adapters with a phy that does 10GBase-T (copper), which is 10 Gigabit ethernet over standard Category 6 cabling. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24ixgbe: Whitespace, copyright update and version number change patchPeter P Waskiewicz
This patch cleans up a bit of whitespace issues with the driver, updates the copyright information, and bumps the version number up. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24ixgbe: update to latest common code moduleJesse Brandeburg
This is a massive update that includes infrastructure for further patches where we will add support for more phy types and eeprom types. This code is shared as much as possible with other drivers, so the code may seem a little obtuse at times but wherever possible we keep to the linux style and methods. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-10ixgbe: driver for Intel(R) 82598 PCI-Express 10GbE adapters (v4)Auke Kok
This patch adds support for the Intel 82598 PCI-Express 10GbE chipset. Devices will be available on the market soon. This version of the driver is largely the same as the last release: * Driver uses a single RX and single TX queue, each using 1 MSI-X irq vector. * Driver runs in NAPI mode only * Driver is largely multiqueue-ready (TM) Changes since 20070803: * removed wrappers for hardware functions * incorporated e1000e-style HW api reorganization code * sparse/checkpatch cleanups, namespace cleanups * driver prints out extra debugging information at load time identifying adapter board number, mac, phy types * removed ixgbe_api.c, ixgbe_api.h, ixgbe_osdep.h * driver update to 1.1.18 * removed ixgbe.txt which contained no useful info anymore [ Integrated napi_struct changes from Auke as well... -DaveM ] Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-05-19 02:25:18 +0000