summaryrefslogtreecommitdiff
path: root/drivers/mtd/nand
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/mtd/nand')
-rw-r--r--drivers/mtd/nand/Kconfig24
-rw-r--r--drivers/mtd/nand/Makefile2
-rw-r--r--drivers/mtd/nand/alauda.c11
-rw-r--r--drivers/mtd/nand/atmel_nand.c5
-rw-r--r--drivers/mtd/nand/bcm_umi_bch.c213
-rw-r--r--drivers/mtd/nand/bcm_umi_nand.c581
-rw-r--r--drivers/mtd/nand/davinci_nand.c4
-rw-r--r--drivers/mtd/nand/excite_nandflash.c248
-rw-r--r--drivers/mtd/nand/fsl_elbc_nand.c86
-rw-r--r--drivers/mtd/nand/fsl_upm.c2
-rw-r--r--drivers/mtd/nand/mxc_nand.c783
-rw-r--r--drivers/mtd/nand/nand_base.c141
-rw-r--r--drivers/mtd/nand/nand_bcm_umi.c149
-rw-r--r--drivers/mtd/nand/nand_bcm_umi.h358
-rw-r--r--drivers/mtd/nand/nand_ecc.c25
-rw-r--r--drivers/mtd/nand/nandsim.c7
-rw-r--r--drivers/mtd/nand/nomadik_nand.c2
-rw-r--r--drivers/mtd/nand/plat_nand.c50
-rw-r--r--drivers/mtd/nand/s3c2410.c2
-rw-r--r--drivers/mtd/nand/txx9ndfmc.c3
20 files changed, 1855 insertions, 841 deletions
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 0e35e1aefd2..677cd53f18c 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -201,6 +201,22 @@ config MTD_NAND_S3C2410_CLKSTOP
when the is NAND chip selected or released, but will save
approximately 5mA of power when there is nothing happening.
+config MTD_NAND_BCM_UMI
+ tristate "NAND Flash support for BCM Reference Boards"
+ depends on ARCH_BCMRING && MTD_NAND
+ help
+ This enables the NAND flash controller on the BCM UMI block.
+
+ No board specfic support is done by this driver, each board
+ must advertise a platform_device for the driver to attach.
+
+config MTD_NAND_BCM_UMI_HWCS
+ bool "BCM UMI NAND Hardware CS"
+ depends on MTD_NAND_BCM_UMI
+ help
+ Enable the use of the BCM UMI block's internal CS using NAND.
+ This should only be used if you know the external NAND CS can toggle.
+
config MTD_NAND_DISKONCHIP
tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation) (EXPERIMENTAL)"
depends on EXPERIMENTAL
@@ -275,14 +291,6 @@ config MTD_NAND_SHARPSL
tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)"
depends on ARCH_PXA
-config MTD_NAND_BASLER_EXCITE
- tristate "Support for NAND Flash on Basler eXcite"
- depends on BASLER_EXCITE
- help
- This enables the driver for the NAND flash device found on the
- Basler eXcite Smart Camera. If built as a module, the driver
- will be named excite_nandflash.
-
config MTD_NAND_CAFE
tristate "NAND support for OLPC CAFÉ chip"
depends on PCI
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 6950d3dabf1..1407bd14401 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -27,7 +27,6 @@ obj-$(CONFIG_MTD_NAND_ATMEL) += atmel_nand.o
obj-$(CONFIG_MTD_NAND_GPIO) += gpio.o
obj-$(CONFIG_MTD_NAND_OMAP2) += omap2.o
obj-$(CONFIG_MTD_NAND_CM_X270) += cmx270_nand.o
-obj-$(CONFIG_MTD_NAND_BASLER_EXCITE) += excite_nandflash.o
obj-$(CONFIG_MTD_NAND_PXA3xx) += pxa3xx_nand.o
obj-$(CONFIG_MTD_NAND_TMIO) += tmio_nand.o
obj-$(CONFIG_MTD_NAND_PLATFORM) += plat_nand.o
@@ -42,5 +41,6 @@ obj-$(CONFIG_MTD_NAND_SOCRATES) += socrates_nand.o
obj-$(CONFIG_MTD_NAND_TXX9NDFMC) += txx9ndfmc.o
obj-$(CONFIG_MTD_NAND_W90P910) += w90p910_nand.o
obj-$(CONFIG_MTD_NAND_NOMADIK) += nomadik_nand.o
+obj-$(CONFIG_MTD_NAND_BCM_UMI) += bcm_umi_nand.o nand_bcm_umi.o
nand-objs := nand_base.o nand_bbt.o
diff --git a/drivers/mtd/nand/alauda.c b/drivers/mtd/nand/alauda.c
index 6d9649159a1..2d6773281fd 100644
--- a/drivers/mtd/nand/alauda.c
+++ b/drivers/mtd/nand/alauda.c
@@ -372,15 +372,6 @@ static int alauda_read_oob(struct mtd_info *mtd, loff_t from, void *oob)
return __alauda_read_page(mtd, from, ignore_buf, oob);
}
-static int popcount8(u8 c)
-{
- int ret = 0;
-
- for ( ; c; c>>=1)
- ret += c & 1;
- return ret;
-}
-
static int alauda_isbad(struct mtd_info *mtd, loff_t ofs)
{
u8 oob[16];
@@ -391,7 +382,7 @@ static int alauda_isbad(struct mtd_info *mtd, loff_t ofs)
return err;
/* A block is marked bad if two or more bits are zero */
- return popcount8(oob[5]) >= 7 ? 0 : 1;
+ return hweight8(oob[5]) >= 7 ? 0 : 1;
}
static int alauda_bounce_read(struct mtd_info *mtd, loff_t from, size_t len,
diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c
index f8e9975c86e..524e6c9e067 100644
--- a/drivers/mtd/nand/atmel_nand.c
+++ b/drivers/mtd/nand/atmel_nand.c
@@ -192,7 +192,6 @@ static int atmel_nand_calculate(struct mtd_info *mtd,
{
struct nand_chip *nand_chip = mtd->priv;
struct atmel_nand_host *host = nand_chip->priv;
- uint32_t *eccpos = nand_chip->ecc.layout->eccpos;
unsigned int ecc_value;
/* get the first 2 ECC bytes */
@@ -464,7 +463,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
if (host->board->det_pin) {
if (gpio_get_value(host->board->det_pin)) {
printk(KERN_INFO "No SmartMedia card inserted.\n");
- res = ENXIO;
+ res = -ENXIO;
goto err_no_card;
}
}
@@ -535,7 +534,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
if ((!partitions) || (num_partitions == 0)) {
printk(KERN_ERR "atmel_nand: No partitions defined, or unsupported device.\n");
- res = ENXIO;
+ res = -ENXIO;
goto err_no_partitions;
}
diff --git a/drivers/mtd/nand/bcm_umi_bch.c b/drivers/mtd/nand/bcm_umi_bch.c
new file mode 100644
index 00000000000..a930666d068
--- /dev/null
+++ b/drivers/mtd/nand/bcm_umi_bch.c
@@ -0,0 +1,213 @@
+/*****************************************************************************
+* Copyright 2004 - 2009 Broadcom Corporation. All rights reserved.
+*
+* Unless you and Broadcom execute a separate written software license
+* agreement governing use of this software, this software is licensed to you
+* under the terms of the GNU General Public License version 2, available at
+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
+*
+* Notwithstanding the above, under no circumstances may you combine this
+* software in any way with any other Broadcom software provided under a
+* license other than the GPL, without Broadcom's express prior written
+* consent.
+*****************************************************************************/
+
+/* ---- Include Files ---------------------------------------------------- */
+#include "nand_bcm_umi.h"
+
+/* ---- External Variable Declarations ----------------------------------- */
+/* ---- External Function Prototypes ------------------------------------- */
+/* ---- Public Variables ------------------------------------------------- */
+/* ---- Private Constants and Types -------------------------------------- */
+
+/* ---- Private Function Prototypes -------------------------------------- */
+static int bcm_umi_bch_read_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, uint8_t *buf, int page);
+static void bcm_umi_bch_write_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, const uint8_t *buf);
+
+/* ---- Private Variables ------------------------------------------------ */
+
+/*
+** nand_hw_eccoob
+** New oob placement block for use with hardware ecc generation.
+*/
+static struct nand_ecclayout nand_hw_eccoob_512 = {
+ /* Reserve 5 for BI indicator */
+ .oobfree = {
+#if (NAND_ECC_NUM_BYTES > 3)
+ {.offset = 0, .length = 2}
+#else
+ {.offset = 0, .length = 5},
+ {.offset = 6, .length = 7}
+#endif
+ }
+};
+
+/*
+** We treat the OOB for a 2K page as if it were 4 512 byte oobs,
+** except the BI is at byte 0.
+*/
+static struct nand_ecclayout nand_hw_eccoob_2048 = {
+ /* Reserve 0 as BI indicator */
+ .oobfree = {
+#if (NAND_ECC_NUM_BYTES > 10)
+ {.offset = 1, .length = 2},
+#elif (NAND_ECC_NUM_BYTES > 7)
+ {.offset = 1, .length = 5},
+ {.offset = 16, .length = 6},
+ {.offset = 32, .length = 6},
+ {.offset = 48, .length = 6}
+#else
+ {.offset = 1, .length = 8},
+ {.offset = 16, .length = 9},
+ {.offset = 32, .length = 9},
+ {.offset = 48, .length = 9}
+#endif
+ }
+};
+
+/* We treat the OOB for a 4K page as if it were 8 512 byte oobs,
+ * except the BI is at byte 0. */
+static struct nand_ecclayout nand_hw_eccoob_4096 = {
+ /* Reserve 0 as BI indicator */
+ .oobfree = {
+#if (NAND_ECC_NUM_BYTES > 10)
+ {.offset = 1, .length = 2},
+ {.offset = 16, .length = 3},
+ {.offset = 32, .length = 3},
+ {.offset = 48, .length = 3},
+ {.offset = 64, .length = 3},
+ {.offset = 80, .length = 3},
+ {.offset = 96, .length = 3},
+ {.offset = 112, .length = 3}
+#else
+ {.offset = 1, .length = 5},
+ {.offset = 16, .length = 6},
+ {.offset = 32, .length = 6},
+ {.offset = 48, .length = 6},
+ {.offset = 64, .length = 6},
+ {.offset = 80, .length = 6},
+ {.offset = 96, .length = 6},
+ {.offset = 112, .length = 6}
+#endif
+ }
+};
+
+/* ---- Private Functions ------------------------------------------------ */
+/* ==== Public Functions ================================================= */
+
+/****************************************************************************
+*
+* bcm_umi_bch_read_page_hwecc - hardware ecc based page read function
+* @mtd: mtd info structure
+* @chip: nand chip info structure
+* @buf: buffer to store read data
+*
+***************************************************************************/
+static int bcm_umi_bch_read_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, uint8_t * buf,
+ int page)
+{
+ int sectorIdx = 0;
+ int eccsize = chip->ecc.size;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *datap = buf;
+ uint8_t eccCalc[NAND_ECC_NUM_BYTES];
+ int sectorOobSize = mtd->oobsize / eccsteps;
+ int stat;
+
+ for (sectorIdx = 0; sectorIdx < eccsteps;
+ sectorIdx++, datap += eccsize) {
+ if (sectorIdx > 0) {
+ /* Seek to page location within sector */
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, sectorIdx * eccsize,
+ -1);
+ }
+
+ /* Enable hardware ECC before reading the buf */
+ nand_bcm_umi_bch_enable_read_hwecc();
+
+ /* Read in data */
+ bcm_umi_nand_read_buf(mtd, datap, eccsize);
+
+ /* Pause hardware ECC after reading the buf */
+ nand_bcm_umi_bch_pause_read_ecc_calc();
+
+ /* Read the OOB ECC */
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT,
+ mtd->writesize + sectorIdx * sectorOobSize, -1);
+ nand_bcm_umi_bch_read_oobEcc(mtd->writesize, eccCalc,
+ NAND_ECC_NUM_BYTES,
+ chip->oob_poi +
+ sectorIdx * sectorOobSize);
+
+ /* Correct any ECC detected errors */
+ stat =
+ nand_bcm_umi_bch_correct_page(datap, eccCalc,
+ NAND_ECC_NUM_BYTES);
+
+ /* Update Stats */
+ if (stat < 0) {
+#if defined(NAND_BCM_UMI_DEBUG)
+ printk(KERN_WARNING "%s uncorr_err sectorIdx=%d\n",
+ __func__, sectorIdx);
+ printk(KERN_WARNING
+ "%s data %02x %02x %02x %02x "
+ "%02x %02x %02x %02x\n",
+ __func__, datap[0], datap[1], datap[2], datap[3],
+ datap[4], datap[5], datap[6], datap[7]);
+ printk(KERN_WARNING
+ "%s ecc %02x %02x %02x %02x "
+ "%02x %02x %02x %02x %02x %02x "
+ "%02x %02x %02x\n",
+ __func__, eccCalc[0], eccCalc[1], eccCalc[2],
+ eccCalc[3], eccCalc[4], eccCalc[5], eccCalc[6],
+ eccCalc[7], eccCalc[8], eccCalc[9], eccCalc[10],
+ eccCalc[11], eccCalc[12]);
+ BUG();
+#endif
+ mtd->ecc_stats.failed++;
+ } else {
+#if defined(NAND_BCM_UMI_DEBUG)
+ if (stat > 0) {
+ printk(KERN_INFO
+ "%s %d correctable_errors detected\n",
+ __func__, stat);
+ }
+#endif
+ mtd->ecc_stats.corrected += stat;
+ }
+ }
+ return 0;
+}
+
+/****************************************************************************
+*
+* bcm_umi_bch_write_page_hwecc - hardware ecc based page write function
+* @mtd: mtd info structure
+* @chip: nand chip info structure
+* @buf: data buffer
+*
+***************************************************************************/
+static void bcm_umi_bch_write_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, const uint8_t *buf)
+{
+ int sectorIdx = 0;
+ int eccsize = chip->ecc.size;
+ int eccsteps = chip->ecc.steps;
+ const uint8_t *datap = buf;
+ uint8_t *oobp = chip->oob_poi;
+ int sectorOobSize = mtd->oobsize / eccsteps;
+
+ for (sectorIdx = 0; sectorIdx < eccsteps;
+ sectorIdx++, datap += eccsize, oobp += sectorOobSize) {
+ /* Enable hardware ECC before writing the buf */
+ nand_bcm_umi_bch_enable_write_hwecc();
+ bcm_umi_nand_write_buf(mtd, datap, eccsize);
+ nand_bcm_umi_bch_write_oobEcc(mtd->writesize, oobp,
+ NAND_ECC_NUM_BYTES);
+ }
+
+ bcm_umi_nand_write_buf(mtd, chip->oob_poi, mtd->oobsize);
+}
diff --git a/drivers/mtd/nand/bcm_umi_nand.c b/drivers/mtd/nand/bcm_umi_nand.c
new file mode 100644
index 00000000000..087bcd745bb
--- /dev/null
+++ b/drivers/mtd/nand/bcm_umi_nand.c
@@ -0,0 +1,581 @@
+/*****************************************************************************
+* Copyright 2004 - 2009 Broadcom Corporation. All rights reserved.
+*
+* Unless you and Broadcom execute a separate written software license
+* agreement governing use of this software, this software is licensed to you
+* under the terms of the GNU General Public License version 2, available at
+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
+*
+* Notwithstanding the above, under no circumstances may you combine this
+* software in any way with any other Broadcom software provided under a
+* license other than the GPL, without Broadcom's express prior written
+* consent.
+*****************************************************************************/
+
+/* ---- Include Files ---------------------------------------------------- */
+#include <linux/version.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/ioport.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/mach-types.h>
+#include <asm/system.h>
+
+#include <mach/reg_nand.h>
+#include <mach/reg_umi.h>
+
+#include "nand_bcm_umi.h"
+
+#include <mach/memory_settings.h>
+
+#define USE_DMA 1
+#include <mach/dma.h>
+#include <linux/dma-mapping.h>
+#include <linux/completion.h>
+
+/* ---- External Variable Declarations ----------------------------------- */
+/* ---- External Function Prototypes ------------------------------------- */
+/* ---- Public Variables ------------------------------------------------- */
+/* ---- Private Constants and Types -------------------------------------- */
+static const __devinitconst char gBanner[] = KERN_INFO \
+ "BCM UMI MTD NAND Driver: 1.00\n";
+
+#ifdef CONFIG_MTD_PARTITIONS
+const char *part_probes[] = { "cmdlinepart", NULL };
+#endif
+
+#if NAND_ECC_BCH
+static uint8_t scan_ff_pattern[] = { 0xff };
+
+static struct nand_bbt_descr largepage_bbt = {
+ .options = 0,
+ .offs = 0,
+ .len = 1,
+ .pattern = scan_ff_pattern
+};
+#endif
+
+/*
+** Preallocate a buffer to avoid having to do this every dma operation.
+** This is the size of the preallocated coherent DMA buffer.
+*/
+#if USE_DMA
+#define DMA_MIN_BUFLEN 512
+#define DMA_MAX_BUFLEN PAGE_SIZE
+#define USE_DIRECT_IO(len) (((len) < DMA_MIN_BUFLEN) || \
+ ((len) > DMA_MAX_BUFLEN))
+
+/*
+ * The current NAND data space goes from 0x80001900 to 0x80001FFF,
+ * which is only 0x700 = 1792 bytes long. This is too small for 2K, 4K page
+ * size NAND flash. Need to break the DMA down to multiple 1Ks.
+ *
+ * Need to make sure REG_NAND_DATA_PADDR + DMA_MAX_LEN < 0x80002000
+ */
+#define DMA_MAX_LEN 1024
+
+#else /* !USE_DMA */
+#define DMA_MIN_BUFLEN 0
+#define DMA_MAX_BUFLEN 0
+#define USE_DIRECT_IO(len) 1
+#endif
+/* ---- Private Function Prototypes -------------------------------------- */
+static void bcm_umi_nand_read_buf(struct mtd_info *mtd, u_char * buf, int len);
+static void bcm_umi_nand_write_buf(struct mtd_info *mtd, const u_char * buf,
+ int len);
+
+/* ---- Private Variables ------------------------------------------------ */
+static struct mtd_info *board_mtd;
+static void __iomem *bcm_umi_io_base;
+static void *virtPtr;
+static dma_addr_t physPtr;
+static struct completion nand_comp;
+
+/* ---- Private Functions ------------------------------------------------ */
+#if NAND_ECC_BCH
+#include "bcm_umi_bch.c"
+#else
+#include "bcm_umi_hamming.c"
+#endif
+
+#if USE_DMA
+
+/* Handler called when the DMA finishes. */
+static void nand_dma_handler(DMA_Device_t dev, int reason, void *userData)
+{
+ complete(&nand_comp);
+}
+
+static int nand_dma_init(void)
+{
+ int rc;
+
+ rc = dma_set_device_handler(DMA_DEVICE_NAND_MEM_TO_MEM,
+ nand_dma_handler, NULL);
+ if (rc != 0) {
+ printk(KERN_ERR "dma_set_device_handler failed: %d\n", rc);
+ return rc;
+ }
+
+ virtPtr =
+ dma_alloc_coherent(NULL, DMA_MAX_BUFLEN, &physPtr, GFP_KERNEL);
+ if (virtPtr == NULL) {
+ printk(KERN_ERR "NAND - Failed to allocate memory for DMA buffer\n");
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+static void nand_dma_term(void)
+{
+ if (virtPtr != NULL)
+ dma_free_coherent(NULL, DMA_MAX_BUFLEN, virtPtr, physPtr);
+}
+
+static void nand_dma_read(void *buf, int len)
+{
+ int offset = 0;
+ int tmp_len = 0;
+ int len_left = len;
+ DMA_Handle_t hndl;
+
+ if (virtPtr == NULL)
+ panic("nand_dma_read: virtPtr == NULL\n");
+
+ if ((void *)physPtr == NULL)
+ panic("nand_dma_read: physPtr == NULL\n");
+
+ hndl = dma_request_channel(DMA_DEVICE_NAND_MEM_TO_MEM);
+ if (hndl < 0) {
+ printk(KERN_ERR
+ "nand_dma_read: unable to allocate dma channel: %d\n",
+ (int)hndl);
+ panic("\n");
+ }
+
+ while (len_left > 0) {
+ if (len_left > DMA_MAX_LEN) {
+ tmp_len = DMA_MAX_LEN;
+ len_left -= DMA_MAX_LEN;
+ } else {
+ tmp_len = len_left;
+ len_left = 0;
+ }
+
+ init_completion(&nand_comp);
+ dma_transfer_mem_to_mem(hndl, REG_NAND_DATA_PADDR,
+ physPtr + offset, tmp_len);
+ wait_for_completion(&nand_comp);
+
+ offset += tmp_len;
+ }
+
+ dma_free_channel(hndl);
+
+ if (buf != NULL)
+ memcpy(buf, virtPtr, len);
+}
+
+static void nand_dma_write(const void *buf, int len)
+{
+ int offset = 0;
+ int tmp_len = 0;
+ int len_left = len;
+ DMA_Handle_t hndl;
+
+ if (buf == NULL)
+ panic("nand_dma_write: buf == NULL\n");
+
+ if (virtPtr == NULL)
+ panic("nand_dma_write: virtPtr == NULL\n");
+
+ if ((void *)physPtr == NULL)
+ panic("nand_dma_write: physPtr == NULL\n");
+
+ memcpy(virtPtr, buf, len);
+
+
+ hndl = dma_request_channel(DMA_DEVICE_NAND_MEM_TO_MEM);
+ if (hndl < 0) {
+ printk(KERN_ERR
+ "nand_dma_write: unable to allocate dma channel: %d\n",
+ (int)hndl);
+ panic("\n");
+ }
+
+ while (len_left > 0) {
+ if (len_left > DMA_MAX_LEN) {
+ tmp_len = DMA_MAX_LEN;
+ len_left -= DMA_MAX_LEN;
+ } else {
+ tmp_len = len_left;
+ len_left = 0;
+ }
+
+ init_completion(&nand_comp);
+ dma_transfer_mem_to_mem(hndl, physPtr + offset,
+ REG_NAND_DATA_PADDR, tmp_len);
+ wait_for_completion(&nand_comp);
+
+ offset += tmp_len;
+ }
+
+ dma_free_channel(hndl);
+}
+
+#endif
+
+static int nand_dev_ready(struct mtd_info *mtd)
+{
+ return nand_bcm_umi_dev_ready();
+}
+
+/****************************************************************************
+*
+* bcm_umi_nand_inithw
+*
+* This routine does the necessary hardware (board-specific)
+* initializations. This includes setting up the timings, etc.
+*
+***************************************************************************/
+int bcm_umi_nand_inithw(void)
+{
+ /* Configure nand timing parameters */
+ REG_UMI_NAND_TCR &= ~0x7ffff;
+ REG_UMI_NAND_TCR |= HW_CFG_NAND_TCR;
+
+#if !defined(CONFIG_MTD_NAND_BCM_UMI_HWCS)
+ /* enable software control of CS */
+ REG_UMI_NAND_TCR |= REG_UMI_NAND_TCR_CS_SWCTRL;
+#endif
+
+ /* keep NAND chip select asserted */
+ REG_UMI_NAND_RCSR |= REG_UMI_NAND_RCSR_CS_ASSERTED;
+
+ REG_UMI_NAND_TCR &= ~REG_UMI_NAND_TCR_WORD16;
+ /* enable writes to flash */
+ REG_UMI_MMD_ICR |= REG_UMI_MMD_ICR_FLASH_WP;
+
+ writel(NAND_CMD_RESET, bcm_umi_io_base + REG_NAND_CMD_OFFSET);
+ nand_bcm_umi_wait_till_ready();
+
+#if NAND_ECC_BCH
+ nand_bcm_umi_bch_config_ecc(NAND_ECC_NUM_BYTES);
+#endif
+
+ return 0;
+}
+
+/* Used to turn latch the proper register for access. */
+static void bcm_umi_nand_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+ /* send command to hardware */
+ struct nand_chip *chip = mtd->priv;
+ if (ctrl & NAND_CTRL_CHANGE) {
+ if (ctrl & NAND_CLE) {
+ chip->IO_ADDR_W = bcm_umi_io_base + REG_NAND_CMD_OFFSET;
+ goto CMD;
+ }
+ if (ctrl & NAND_ALE) {
+ chip->IO_ADDR_W =
+ bcm_umi_io_base + REG_NAND_ADDR_OFFSET;
+ goto CMD;
+ }
+ chip->IO_ADDR_W = bcm_umi_io_base + REG_NAND_DATA8_OFFSET;
+ }
+
+CMD:
+ /* Send command to chip directly */
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, chip->IO_ADDR_W);
+}
+
+static void bcm_umi_nand_write_buf(struct mtd_info *mtd, const u_char * buf,
+ int len)
+{
+ if (USE_DIRECT_IO(len)) {
+ /* Do it the old way if the buffer is small or too large.
+ * Probably quicker than starting and checking dma. */
+ int i;
+ struct nand_chip *this = mtd->priv;
+
+ for (i = 0; i < len; i++)
+ writeb(buf[i], this->IO_ADDR_W);
+ }
+#if USE_DMA
+ else
+ nand_dma_write(buf, len);
+#endif
+}
+
+static void bcm_umi_nand_read_buf(struct mtd_info *mtd, u_char * buf, int len)
+{
+ if (USE_DIRECT_IO(len)) {
+ int i;
+ struct nand_chip *this = mtd->priv;
+
+ for (i = 0; i < len; i++)
+ buf[i] = readb(this->IO_ADDR_R);
+ }
+#if USE_DMA
+ else
+ nand_dma_read(buf, len);
+#endif
+}
+
+static uint8_t readbackbuf[NAND_MAX_PAGESIZE];
+static int bcm_umi_nand_verify_buf(struct mtd_info *mtd, const u_char * buf,
+ int len)
+{
+ /*
+ * Try to readback page with ECC correction. This is necessary
+ * for MLC parts which may have permanently stuck bits.
+ */
+ struct nand_chip *chip = mtd->priv;
+ int ret = chip->ecc.read_page(mtd, chip, readbackbuf, 0);
+ if (ret < 0)
+ return -EFAULT;
+ else {
+ if (memcmp(readbackbuf, buf, len) == 0)
+ return 0;
+
+ return -EFAULT;
+ }
+ return 0;
+}
+
+static int __devinit bcm_umi_nand_probe(struct platform_device *pdev)
+{
+ struct nand_chip *this;
+ struct resource *r;
+ int err = 0;
+
+ printk(gBanner);
+
+ /* Allocate memory for MTD device structure and private data */
+ board_mtd =
+ kmalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip),
+ GFP_KERNEL);
+ if (!board_mtd) {
+ printk(KERN_WARNING
+ "Unable to allocate NAND MTD device structure.\n");
+ return -ENOMEM;
+ }
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ if (!r)
+ return -ENXIO;
+
+ /* map physical adress */
+ bcm_umi_io_base = ioremap(r->start, r->end - r->start + 1);
+
+ if (!bcm_umi_io_base) {
+ printk(KERN_ERR "ioremap to access BCM UMI NAND chip failed\n");
+ kfree(board_mtd);
+ return -EIO;
+ }
+
+ /* Get pointer to private data */
+ this = (struct nand_chip *)(&board_mtd[1]);
+
+ /* Initialize structures */
+ memset((char *)board_mtd, 0, sizeof(struct mtd_info));
+ memset((char *)this, 0, sizeof(struct nand_chip));
+
+ /* Link the private data with the MTD structure */
+ board_mtd->priv = this;
+
+ /* Initialize the NAND hardware. */
+ if (bcm_umi_nand_inithw() < 0) {
+ printk(KERN_ERR "BCM UMI NAND chip could not be initialized\n");
+ iounmap(bcm_umi_io_base);
+ kfree(board_mtd);
+ return -EIO;
+ }
+
+ /* Set address of NAND IO lines */
+ this->IO_ADDR_W = bcm_umi_io_base + REG_NAND_DATA8_OFFSET;
+ this->IO_ADDR_R = bcm_umi_io_base + REG_NAND_DATA8_OFFSET;
+
+ /* Set command delay time, see datasheet for correct value */
+ this->chip_delay = 0;
+ /* Assign the device ready function, if available */
+ this->dev_ready = nand_dev_ready;
+ this->options = 0;
+
+ this->write_buf = bcm_umi_nand_write_buf;
+ this->read_buf = bcm_umi_nand_read_buf;
+ this->verify_buf = bcm_umi_nand_verify_buf;
+
+ this->cmd_ctrl = bcm_umi_nand_hwcontrol;
+ this->ecc.mode = NAND_ECC_HW;
+ this->ecc.size = 512;
+ this->ecc.bytes = NAND_ECC_NUM_BYTES;
+#if NAND_ECC_BCH
+ this->ecc.read_page = bcm_umi_bch_read_page_hwecc;
+ this->ecc.write_page = bcm_umi_bch_write_page_hwecc;
+#else
+ this->ecc.correct = nand_correct_data512;
+ this->ecc.calculate = bcm_umi_hamming_get_hw_ecc;
+ this->ecc.hwctl = bcm_umi_hamming_enable_hwecc;
+#endif
+
+#if USE_DMA
+ err = nand_dma_init();
+ if (err != 0)
+ return err;
+#endif
+
+ /* Figure out the size of the device that we have.
+ * We need to do this to figure out which ECC
+ * layout we'll be using.
+ */
+
+ err = nand_scan_ident(board_mtd, 1);
+ if (err) {
+ printk(KERN_ERR "nand_scan failed: %d\n", err);
+ iounmap(bcm_umi_io_base);
+ kfree(board_mtd);
+ return err;
+ }
+
+ /* Now that we know the nand size, we can setup the ECC layout */
+
+ switch (board_mtd->writesize) { /* writesize is the pagesize */
+ case 4096:
+ this->ecc.layout = &nand_hw_eccoob_4096;
+ break;
+ case 2048:
+ this->ecc.layout = &nand_hw_eccoob_2048;
+ break;
+ case 512:
+ this->ecc.layout = &nand_hw_eccoob_512;
+ break;
+ default:
+ {
+ printk(KERN_ERR "NAND - Unrecognized pagesize: %d\n",
+ board_mtd->writesize);
+ return -EINVAL;
+ }
+ }
+
+#if NAND_ECC_BCH
+ if (board_mtd->writesize > 512) {
+ if (this->options & NAND_USE_FLASH_BBT)
+ largepage_bbt.options = NAND_BBT_SCAN2NDPAGE;
+ this->badblock_pattern = &largepage_bbt;
+ }
+#endif
+
+ /* Now finish off the scan, now that ecc.layout has been initialized. */
+
+ err = nand_scan_tail(board_mtd);
+ if (err) {
+ printk(KERN_ERR "nand_scan failed: %d\n", err);
+ iounmap(bcm_umi_io_base);
+ kfree(board_mtd);
+ return err;
+ }
+
+ /* Register the partitions */
+ {
+ int nr_partitions;
+ struct mtd_partition *partition_info;
+
+ board_mtd->name = "bcm_umi-nand";
+ nr_partitions =
+ parse_mtd_partitions(board_mtd, part_probes,
+ &partition_info, 0);
+
+ if (nr_partitions <= 0) {
+ printk(KERN_ERR "BCM UMI NAND: Too few partitions - %d\n",
+ nr_partitions);
+ iounmap(bcm_umi_io_base);
+ kfree(board_mtd);
+ return -EIO;
+ }
+ add_mtd_partitions(board_mtd, partition_info, nr_partitions);
+ }
+
+ /* Return happy */
+ return 0;
+}
+
+static int bcm_umi_nand_remove(struct platform_device *pdev)
+{
+#if USE_DMA
+ nand_dma_term();
+#endif
+
+ /* Release resources, unregister device */
+ nand_release(board_mtd);
+
+ /* unmap physical adress */
+ iounmap(bcm_umi_io_base);
+
+ /* Free the MTD device structure */
+ kfree(board_mtd);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int bcm_umi_nand_suspend(struct platform_device *pdev,
+ pm_message_t state)
+{
+ printk(KERN_ERR "MTD NAND suspend is being called\n");
+ return 0;
+}
+
+static int bcm_umi_nand_resume(struct platform_device *pdev)
+{
+ printk(KERN_ERR "MTD NAND resume is being called\n");
+ return 0;
+}
+#else
+#define bcm_umi_nand_suspend NULL
+#define bcm_umi_nand_resume NULL
+#endif
+
+static struct platform_driver nand_driver = {
+ .driver = {
+ .name = "bcm-nand",
+ .owner = THIS_MODULE,
+ },
+ .probe = bcm_umi_nand_probe,
+ .remove = bcm_umi_nand_remove,
+ .suspend = bcm_umi_nand_suspend,
+ .resume = bcm_umi_nand_resume,
+};
+
+static int __init nand_init(void)
+{
+ return platform_driver_register(&nand_driver);
+}
+
+static void __exit nand_exit(void)
+{
+ platform_driver_unregister(&nand_driver);
+}
+
+module_init(nand_init);
+module_exit(nand_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Broadcom");
+MODULE_DESCRIPTION("BCM UMI MTD NAND driver");
diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c
index f13f5b9afaf..fe3eba87de4 100644
--- a/drivers/mtd/nand/davinci_nand.c
+++ b/drivers/mtd/nand/davinci_nand.c
@@ -591,6 +591,8 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
/* options such as NAND_USE_FLASH_BBT or 16-bit widths */
info->chip.options = pdata->options;
+ info->chip.bbt_td = pdata->bbt_td;
+ info->chip.bbt_md = pdata->bbt_md;
info->ioaddr = (uint32_t __force) vaddr;
@@ -599,7 +601,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
info->mask_chipsel = pdata->mask_chipsel;
/* use nandboot-capable ALE/CLE masks by default */
- info->mask_ale = pdata->mask_cle ? : MASK_ALE;
+ info->mask_ale = pdata->mask_ale ? : MASK_ALE;
info->mask_cle = pdata->mask_cle ? : MASK_CLE;
/* Set address of hardware control function */
diff --git a/drivers/mtd/nand/excite_nandflash.c b/drivers/mtd/nand/excite_nandflash.c
deleted file mode 100644
index 72446fb48d4..00000000000
--- a/drivers/mtd/nand/excite_nandflash.c
+++ /dev/null
@@ -1,248 +0,0 @@
-/*
-* Copyright (C) 2005 - 2007 by Basler Vision Technologies AG
-* Author: Thomas Koeller <thomas.koeller.qbaslerweb.com>
-* Original code by Thies Moeller <thies.moeller@baslerweb.com>
-*
-* This program is free software; you can redistribute it and/or modify
-* it under the terms of the GNU General Public License as published by
-* the Free Software Foundation; either version 2 of the License, or
-* (at your option) any later version.
-*
-* This program is distributed in the hope that it will be useful,
-* but WITHOUT ANY WARRANTY; without even the implied warranty of
-* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-* GNU General Public License for more details.
-*
-* You should have received a copy of the GNU General Public License
-* along with this program; if not, write to the Free Software
-* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-*/
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/string.h>
-#include <linux/ioport.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/nand_ecc.h>
-#include <linux/mtd/partitions.h>
-
-#include <asm/io.h>
-#include <asm/rm9k-ocd.h>
-
-#include <excite_nandflash.h>
-
-#define EXCITE_NANDFLASH_VERSION "0.1"
-
-/* I/O register offsets */
-#define EXCITE_NANDFLASH_DATA_BYTE 0x00
-#define EXCITE_NANDFLASH_STATUS_BYTE 0x0c
-#define EXCITE_NANDFLASH_ADDR_BYTE 0x10
-#define EXCITE_NANDFLASH_CMD_BYTE 0x14
-
-/* prefix for debug output */
-static const char module_id[] = "excite_nandflash";
-
-/*
- * partition definition
- */
-static const struct mtd_partition partition_info[] = {
- {
- .name = "eXcite RootFS",
- .offset = 0,
- .size = MTDPART_SIZ_FULL
- }
-};
-
-static inline const struct resource *
-excite_nand_get_resource(struct platform_device *d, unsigned long flags,
- const char *basename)
-{
- char buf[80];
-
- if (snprintf(buf, sizeof buf, "%s_%u", basename, d->id) >= sizeof buf)
- return NULL;
- return platform_get_resource_byname(d, flags, buf);
-}
-
-static inline void __iomem *
-excite_nand_map_regs(struct platform_device *d, const char *basename)
-{
- void *result = NULL;
- const struct resource *const r =
- excite_nand_get_resource(d, IORESOURCE_MEM, basename);
-
- if (r)
- result = ioremap_nocache(r->start, r->end + 1 - r->start);
- return result;
-}
-
-/* controller and mtd information */
-struct excite_nand_drvdata {
- struct mtd_info board_mtd;
- struct nand_chip board_chip;
- void __iomem *regs;
- void __iomem *tgt;
-};
-
-/* Control function */
-static void excite_nand_control(struct mtd_info *mtd, int cmd,
- unsigned int ctrl)
-{
- struct excite_nand_drvdata * const d =
- container_of(mtd, struct excite_nand_drvdata, board_mtd);
-
- switch (ctrl) {
- case NAND_CTRL_CHANGE | NAND_CTRL_CLE:
- d->tgt = d->regs + EXCITE_NANDFLASH_CMD_BYTE;
- break;
- case NAND_CTRL_CHANGE | NAND_CTRL_ALE:
- d->tgt = d->regs + EXCITE_NANDFLASH_ADDR_BYTE;
- break;
- case NAND_CTRL_CHANGE | NAND_NCE:
- d->tgt = d->regs + EXCITE_NANDFLASH_DATA_BYTE;
- break;
- }
-
- if (cmd != NAND_CMD_NONE)
- __raw_writeb(cmd, d->tgt);
-}
-
-/* Return 0 if flash is busy, 1 if ready */
-static int excite_nand_devready(struct mtd_info *mtd)
-{
- struct excite_nand_drvdata * const drvdata =
- container_of(mtd, struct excite_nand_drvdata, board_mtd);
-
- return __raw_readb(drvdata->regs + EXCITE_NANDFLASH_STATUS_BYTE);
-}
-
-/*
- * Called by device layer to remove the driver.
- * The binding to the mtd and all allocated
- * resources are released.
- */
-static int __exit excite_nand_remove(struct platform_device *dev)
-{
- struct excite_nand_drvdata * const this = platform_get_drvdata(dev);
-
- platform_set_drvdata(dev, NULL);
-
- if (unlikely(!this)) {
- printk(KERN_ERR "%s: called %s without private data!!",
- module_id, __func__);
- return -EINVAL;
- }
-
- /* first thing we need to do is release our mtd
- * then go through freeing the resource used
- */
- nand_release(&this->board_mtd);
-
- /* free the common resources */
- iounmap(this->regs);
- kfree(this);
-
- DEBUG(MTD_DEBUG_LEVEL1, "%s: removed\n", module_id);
- return 0;
-}
-
-/*
- * Called by device layer when it finds a device matching
- * one our driver can handle. This code checks to see if
- * it can allocate all necessary resources then calls the
- * nand layer to look for devices.
-*/
-static int __init excite_nand_probe(struct platform_device *pdev)
-{
- struct excite_nand_drvdata *drvdata; /* private driver data */
- struct nand_chip *board_chip; /* private flash chip data */
- struct mtd_info *board_mtd; /* mtd info for this board */
- int scan_res;
-
- drvdata = kzalloc(sizeof(*drvdata), GFP_KERNEL);
- if (unlikely(!drvdata)) {
- printk(KERN_ERR "%s: no memory for drvdata\n",
- module_id);
- return -ENOMEM;
- }
-
- /* bind private data into driver */
- platform_set_drvdata(pdev, drvdata);
-
- /* allocate and map the resource */
- drvdata->regs =
- excite_nand_map_regs(pdev, EXCITE_NANDFLASH_RESOURCE_REGS);
-
- if (unlikely(!drvdata->regs)) {
- printk(KERN_ERR "%s: cannot reserve register region\n",
- module_id);
- kfree(drvdata);
- return -ENXIO;
- }
-
- drvdata->tgt = drvdata->regs + EXCITE_NANDFLASH_DATA_BYTE;
-
- /* initialise our chip */
- board_chip = &drvdata->board_chip;
- board_chip->IO_ADDR_R = board_chip->IO_ADDR_W =
- drvdata->regs + EXCITE_NANDFLASH_DATA_BYTE;
- board_chip->cmd_ctrl = excite_nand_control;
- board_chip->dev_ready = excite_nand_devready;
- board_chip->chip_delay = 25;
- board_chip->ecc.mode = NAND_ECC_SOFT;
-
- /* link chip to mtd */
- board_mtd = &drvdata->board_mtd;
- board_mtd->priv = board_chip;
-
- DEBUG(MTD_DEBUG_LEVEL2, "%s: device scan\n", module_id);
- scan_res = nand_scan(&drvdata->board_mtd, 1);
-
- if (likely(!scan_res)) {
- DEBUG(MTD_DEBUG_LEVEL2, "%s: register partitions\n", module_id);
- add_mtd_partitions(&drvdata->board_mtd, partition_info,
- ARRAY_SIZE(partition_info));
- } else {
- iounmap(drvdata->regs);
- kfree(drvdata);
- printk(KERN_ERR "%s: device scan failed\n", module_id);
- return -EIO;
- }
- return 0;
-}
-
-static struct platform_driver excite_nand_driver = {
- .driver = {
- .name = "excite_nand",
- .owner = THIS_MODULE,
- },
- .probe = excite_nand_probe,
- .remove = __devexit_p(excite_nand_remove)
-};
-
-static int __init excite_nand_init(void)
-{
- pr_info("Basler eXcite nand flash driver Version "
- EXCITE_NANDFLASH_VERSION "\n");
- return platform_driver_register(&excite_nand_driver);
-}
-
-static void __exit excite_nand_exit(void)
-{
- platform_driver_unregister(&excite_nand_driver);
-}
-
-module_init(excite_nand_init);
-module_exit(excite_nand_exit);
-
-MODULE_AUTHOR("Thomas Koeller <thomas.koeller@baslerweb.com>");
-MODULE_DESCRIPTION("Basler eXcite NAND-Flash driver");
-MODULE_LICENSE("GPL");
-MODULE_VERSION(EXCITE_NANDFLASH_VERSION)
diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c
index ddd37d2554e..ae30fb6eed9 100644
--- a/drivers/mtd/nand/fsl_elbc_nand.c
+++ b/drivers/mtd/nand/fsl_elbc_nand.c
@@ -237,12 +237,15 @@ static int fsl_elbc_run_command(struct mtd_info *mtd)
ctrl->use_mdr = 0;
- dev_vdbg(ctrl->dev,
- "fsl_elbc_run_command: stat=%08x mdr=%08x fmr=%08x\n",
- ctrl->status, ctrl->mdr, in_be32(&lbc->fmr));
+ if (ctrl->status != LTESR_CC) {
+ dev_info(ctrl->dev,
+ "command failed: fir %x fcr %x status %x mdr %x\n",
+ in_be32(&lbc->fir), in_be32(&lbc->fcr),
+ ctrl->status, ctrl->mdr);
+ return -EIO;
+ }
- /* returns 0 on success otherwise non-zero) */
- return ctrl->status == LTESR_CC ? 0 : -EIO;
+ return 0;
}
static void fsl_elbc_do_read(struct nand_chip *chip, int oob)
@@ -253,17 +256,17 @@ static void fsl_elbc_do_read(struct nand_chip *chip, int oob)
if (priv->page_size) {
out_be32(&lbc->fir,
- (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CM0 << FIR_OP0_SHIFT) |
(FIR_OP_CA << FIR_OP1_SHIFT) |
(FIR_OP_PA << FIR_OP2_SHIFT) |
- (FIR_OP_CW1 << FIR_OP3_SHIFT) |
+ (FIR_OP_CM1 << FIR_OP3_SHIFT) |
(FIR_OP_RBW << FIR_OP4_SHIFT));
out_be32(&lbc->fcr, (NAND_CMD_READ0 << FCR_CMD0_SHIFT) |
(NAND_CMD_READSTART << FCR_CMD1_SHIFT));
} else {
out_be32(&lbc->fir,
- (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CM0 << FIR_OP0_SHIFT) |
(FIR_OP_CA << FIR_OP1_SHIFT) |
(FIR_OP_PA << FIR_OP2_SHIFT) |
(FIR_OP_RBW << FIR_OP3_SHIFT));
@@ -332,7 +335,7 @@ static void fsl_elbc_cmdfunc(struct mtd_info *mtd, unsigned int command,
case NAND_CMD_READID:
dev_vdbg(ctrl->dev, "fsl_elbc_cmdfunc: NAND_CMD_READID.\n");
- out_be32(&lbc->fir, (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ out_be32(&lbc->fir, (FIR_OP_CM0 << FIR_OP0_SHIFT) |
(FIR_OP_UA << FIR_OP1_SHIFT) |
(FIR_OP_RBW << FIR_OP2_SHIFT));
out_be32(&lbc->fcr, NAND_CMD_READID << FCR_CMD0_SHIFT);
@@ -359,16 +362,20 @@ static void fsl_elbc_cmdfunc(struct mtd_info *mtd, unsigned int command,
dev_vdbg(ctrl->dev, "fsl_elbc_cmdfunc: NAND_CMD_ERASE2.\n");
out_be32(&lbc->fir,
- (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CM0 << FIR_OP0_SHIFT) |
(FIR_OP_PA << FIR_OP1_SHIFT) |
- (FIR_OP_CM1 << FIR_OP2_SHIFT));
+ (FIR_OP_CM2 << FIR_OP2_SHIFT) |
+ (FIR_OP_CW1 << FIR_OP3_SHIFT) |
+ (FIR_OP_RS << FIR_OP4_SHIFT));
out_be32(&lbc->fcr,
(NAND_CMD_ERASE1 << FCR_CMD0_SHIFT) |
- (NAND_CMD_ERASE2 << FCR_CMD1_SHIFT));
+ (NAND_CMD_STATUS << FCR_CMD1_SHIFT) |
+ (NAND_CMD_ERASE2 << FCR_CMD2_SHIFT));
out_be32(&lbc->fbcr, 0);
ctrl->read_bytes = 0;
+ ctrl->use_mdr = 1;
fsl_elbc_run_command(mtd);
return;
@@ -383,40 +390,41 @@ static void fsl_elbc_cmdfunc(struct mtd_info *mtd, unsigned int command,
ctrl->column = column;
ctrl->oob = 0;
+ ctrl->use_mdr = 1;
- if (priv->page_size) {
- fcr = (NAND_CMD_SEQIN << FCR_CMD0_SHIFT) |
- (NAND_CMD_PAGEPROG << FCR_CMD1_SHIFT);
+ fcr = (NAND_CMD_STATUS << FCR_CMD1_SHIFT) |
+ (NAND_CMD_SEQIN << FCR_CMD2_SHIFT) |
+ (NAND_CMD_PAGEPROG << FCR_CMD3_SHIFT);
+ if (priv->page_size) {
out_be32(&lbc->fir,
- (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CM2 << FIR_OP0_SHIFT) |
(FIR_OP_CA << FIR_OP1_SHIFT) |
(FIR_OP_PA << FIR_OP2_SHIFT) |
(FIR_OP_WB << FIR_OP3_SHIFT) |
- (FIR_OP_CW1 << FIR_OP4_SHIFT));
+ (FIR_OP_CM3 << FIR_OP4_SHIFT) |
+ (FIR_OP_CW1 << FIR_OP5_SHIFT) |
+ (FIR_OP_RS << FIR_OP6_SHIFT));
} else {
- fcr = (NAND_CMD_PAGEPROG << FCR_CMD1_SHIFT) |
- (NAND_CMD_SEQIN << FCR_CMD2_SHIFT);
-
out_be32(&lbc->fir,
- (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CM0 << FIR_OP0_SHIFT) |
(FIR_OP_CM2 << FIR_OP1_SHIFT) |
(FIR_OP_CA << FIR_OP2_SHIFT) |
(FIR_OP_PA << FIR_OP3_SHIFT) |
(FIR_OP_WB << FIR_OP4_SHIFT) |
- (FIR_OP_CW1 << FIR_OP5_SHIFT));
+ (FIR_OP_CM3 << FIR_OP5_SHIFT) |
+ (FIR_OP_CW1 << FIR_OP6_SHIFT) |
+ (FIR_OP_RS << FIR_OP7_SHIFT));
if (column >= mtd->writesize) {
/* OOB area --> READOOB */
column -= mtd->writesize;
fcr |= NAND_CMD_READOOB << FCR_CMD0_SHIFT;
ctrl->oob = 1;
- } else if (column < 256) {
+ } else {
+ WARN_ON(column != 0);
/* First 256 bytes --> READ0 */
fcr |= NAND_CMD_READ0 << FCR_CMD0_SHIFT;
- } else {
- /* Second 256 bytes --> READ1 */
- fcr |= NAND_CMD_READ1 << FCR_CMD0_SHIFT;
}
}
@@ -628,22 +636,6 @@ static int fsl_elbc_wait(struct mtd_info *mtd, struct nand_chip *chip)
{
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
-
- if (ctrl->status != LTESR_CC)
- return NAND_STATUS_FAIL;
-
- /* Use READ_STATUS command, but wait for the device to be ready */
- ctrl->use_mdr = 0;
- out_be32(&lbc->fir,
- (FIR_OP_CW0 << FIR_OP0_SHIFT) |
- (FIR_OP_RBW << FIR_OP1_SHIFT));
- out_be32(&lbc->fcr, NAND_CMD_STATUS << FCR_CMD0_SHIFT);
- out_be32(&lbc->fbcr, 1);
- set_addr(mtd, 0, 0, 0);
- ctrl->read_bytes = 1;
-
- fsl_elbc_run_command(mtd);
if (ctrl->status != LTESR_CC)
return NAND_STATUS_FAIL;
@@ -651,8 +643,7 @@ static int fsl_elbc_wait(struct mtd_info *mtd, struct nand_chip *chip)
/* The chip always seems to report that it is
* write-protected, even when it is not.
*/
- setbits8(ctrl->addr, NAND_STATUS_WP);
- return fsl_elbc_read_byte(mtd);
+ return (ctrl->mdr & 0xff) | NAND_STATUS_WP;
}
static int fsl_elbc_chip_init_tail(struct mtd_info *mtd)
@@ -946,6 +937,13 @@ static int __devinit fsl_elbc_ctrl_init(struct fsl_elbc_ctrl *ctrl)
{
struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
+ /*
+ * NAND transactions can tie up the bus for a long time, so set the
+ * bus timeout to max by clearing LBCR[BMT] (highest base counter
+ * value) and setting LBCR[BMTPS] to the highest prescaler value.
+ */
+ clrsetbits_be32(&lbc->lbcr, LBCR_BMT, 15);
+
/* clear event registers */
setbits32(&lbc->ltesr, LTESR_NAND_MASK);
out_be32(&lbc->lteatr, 0);
diff --git a/drivers/mtd/nand/fsl_upm.c b/drivers/mtd/nand/fsl_upm.c
index d120cd8d726..071a60cb420 100644
--- a/drivers/mtd/nand/fsl_upm.c
+++ b/drivers/mtd/nand/fsl_upm.c
@@ -112,7 +112,7 @@ static void fun_select_chip(struct mtd_info *mtd, int mchip_nr)
if (mchip_nr == -1) {
chip->cmd_ctrl(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE);
- } else if (mchip_nr >= 0) {
+ } else if (mchip_nr >= 0 && mchip_nr < NAND_MAX_CHIPS) {
fun->mchip_number = mchip_nr;
chip->IO_ADDR_R = fun->io_base + fun->mchip_offsets[mchip_nr];
chip->IO_ADDR_W = chip->IO_ADDR_R;
diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/mxc_nand.c
index 65b26d5a5c0..45dec5770da 100644
--- a/drivers/mtd/nand/mxc_nand.c
+++ b/drivers/mtd/nand/mxc_nand.c
@@ -33,9 +33,13 @@
#include <asm/mach/flash.h>
#include <mach/mxc_nand.h>
+#include <mach/hardware.h>
#define DRIVER_NAME "mxc_nand"
+#define nfc_is_v21() (cpu_is_mx25() || cpu_is_mx35())
+#define nfc_is_v1() (cpu_is_mx31() || cpu_is_mx27())
+
/* Addresses for NFC registers */
#define NFC_BUF_SIZE 0xE00
#define NFC_BUF_ADDR 0xE04
@@ -46,24 +50,14 @@
#define NFC_RSLTMAIN_AREA 0xE0E
#define NFC_RSLTSPARE_AREA 0xE10
#define NFC_WRPROT 0xE12
-#define NFC_UNLOCKSTART_BLKADDR 0xE14
-#define NFC_UNLOCKEND_BLKADDR 0xE16
+#define NFC_V1_UNLOCKSTART_BLKADDR 0xe14
+#define NFC_V1_UNLOCKEND_BLKADDR 0xe16
+#define NFC_V21_UNLOCKSTART_BLKADDR 0xe20
+#define NFC_V21_UNLOCKEND_BLKADDR 0xe22
#define NFC_NF_WRPRST 0xE18
#define NFC_CONFIG1 0xE1A
#define NFC_CONFIG2 0xE1C
-/* Addresses for NFC RAM BUFFER Main area 0 */
-#define MAIN_AREA0 0x000
-#define MAIN_AREA1 0x200
-#define MAIN_AREA2 0x400
-#define MAIN_AREA3 0x600
-
-/* Addresses for NFC SPARE BUFFER Spare area 0 */
-#define SPARE_AREA0 0x800
-#define SPARE_AREA1 0x810
-#define SPARE_AREA2 0x820
-#define SPARE_AREA3 0x830
-
/* Set INT to 0, FCMD to 1, rest to 0 in NFC_CONFIG2 Register
* for Command operation */
#define NFC_CMD 0x1
@@ -106,48 +100,66 @@ struct mxc_nand_host {
struct mtd_partition *parts;
struct device *dev;
+ void *spare0;
+ void *main_area0;
+ void *main_area1;
+
+ void __iomem *base;
void __iomem *regs;
- int spare_only;
int status_request;
- int pagesize_2k;
- uint16_t col_addr;
struct clk *clk;
int clk_act;
int irq;
wait_queue_head_t irq_waitq;
-};
-
-/* Define delays in microsec for NAND device operations */
-#define TROP_US_DELAY 2000
-/* Macros to get byte and bit positions of ECC */
-#define COLPOS(x) ((x) >> 3)
-#define BITPOS(x) ((x) & 0xf)
-/* Define single bit Error positions in Main & Spare area */
-#define MAIN_SINGLEBIT_ERROR 0x4
-#define SPARE_SINGLEBIT_ERROR 0x1
-
-/* OOB placement block for use with hardware ecc generation */
-static struct nand_ecclayout nand_hw_eccoob_8 = {
- .eccbytes = 5,
- .eccpos = {6, 7, 8, 9, 10},
- .oobfree = {{0, 5}, {11, 5}, }
+ uint8_t *data_buf;
+ unsigned int buf_start;
+ int spare_len;
};
-static struct nand_ecclayout nand_hw_eccoob_16 = {
+/* OOB placement block for use with hardware ecc generation */
+static struct nand_ecclayout nandv1_hw_eccoob_smallpage = {
.eccbytes = 5,
.eccpos = {6, 7, 8, 9, 10},
- .oobfree = {{0, 5}, {11, 5}, }
+ .oobfree = {{0, 5}, {12, 4}, }
};
-static struct nand_ecclayout nand_hw_eccoob_64 = {
+static struct nand_ecclayout nandv1_hw_eccoob_largepage = {
.eccbytes = 20,
.eccpos = {6, 7, 8, 9, 10, 22, 23, 24, 25, 26,
38, 39, 40, 41, 42, 54, 55, 56, 57, 58},
.oobfree = {{2, 4}, {11, 10}, {27, 10}, {43, 10}, {59, 5}, }
};
+/* OOB description for 512 byte pages with 16 byte OOB */
+static struct nand_ecclayout nandv2_hw_eccoob_smallpage = {
+ .eccbytes = 1 * 9,
+ .eccpos = {
+ 7, 8, 9, 10, 11, 12, 13, 14, 15
+ },
+ .oobfree = {
+ {.offset = 0, .length = 5}
+ }
+};
+
+/* OOB description for 2048 byte pages with 64 byte OOB */
+static struct nand_ecclayout nandv2_hw_eccoob_largepage = {
+ .eccbytes = 4 * 9,
+ .eccpos = {
+ 7, 8, 9, 10, 11, 12, 13, 14, 15,
+ 23, 24, 25, 26, 27, 28, 29, 30, 31,
+ 39, 40, 41, 42, 43, 44, 45, 46, 47,
+ 55, 56, 57, 58, 59, 60, 61, 62, 63
+ },
+ .oobfree = {
+ {.offset = 2, .length = 4},
+ {.offset = 16, .length = 7},
+ {.offset = 32, .length = 7},
+ {.offset = 48, .length = 7}
+ }
+};
+
#ifdef CONFIG_MTD_PARTITIONS
static const char *part_probes[] = { "RedBoot", "cmdlinepart", NULL };
#endif
@@ -170,10 +182,10 @@ static irqreturn_t mxc_nfc_irq(int irq, void *dev_id)
/* This function polls the NANDFC to wait for the basic operation to
* complete by checking the INT bit of config2 register.
*/
-static void wait_op_done(struct mxc_nand_host *host, int max_retries,
- uint16_t param, int useirq)
+static void wait_op_done(struct mxc_nand_host *host, int useirq)
{
uint32_t tmp;
+ int max_retries = 2000;
if (useirq) {
if ((readw(host->regs + NFC_CONFIG2) & NFC_INT) == 0) {
@@ -200,8 +212,8 @@ static void wait_op_done(struct mxc_nand_host *host, int max_retries,
udelay(1);
}
if (max_retries < 0)
- DEBUG(MTD_DEBUG_LEVEL0, "%s(%d): INT not set\n",
- __func__, param);
+ DEBUG(MTD_DEBUG_LEVEL0, "%s: INT not set\n",
+ __func__);
}
}
@@ -215,7 +227,7 @@ static void send_cmd(struct mxc_nand_host *host, uint16_t cmd, int useirq)
writew(NFC_CMD, host->regs + NFC_CONFIG2);
/* Wait for operation to complete */
- wait_op_done(host, TROP_US_DELAY, cmd, useirq);
+ wait_op_done(host, useirq);
}
/* This function sends an address (or partial address) to the
@@ -229,82 +241,47 @@ static void send_addr(struct mxc_nand_host *host, uint16_t addr, int islast)
writew(NFC_ADDR, host->regs + NFC_CONFIG2);
/* Wait for operation to complete */
- wait_op_done(host, TROP_US_DELAY, addr, islast);
+ wait_op_done(host, islast);
}
-/* This function requests the NANDFC to initate the transfer
- * of data currently in the NANDFC RAM buffer to the NAND device. */
-static void send_prog_page(struct mxc_nand_host *host, uint8_t buf_id,
- int spare_only)
+static void send_page(struct mtd_info *mtd, unsigned int ops)
{
- DEBUG(MTD_DEBUG_LEVEL3, "send_prog_page (%d)\n", spare_only);
-
- /* NANDFC buffer 0 is used for page read/write */
- writew(buf_id, host->regs + NFC_BUF_ADDR);
-
- /* Configure spare or page+spare access */
- if (!host->pagesize_2k) {
- uint16_t config1 = readw(host->regs + NFC_CONFIG1);
- if (spare_only)
- config1 |= NFC_SP_EN;
- else
- config1 &= ~(NFC_SP_EN);
- writew(config1, host->regs + NFC_CONFIG1);
- }
+ struct nand_chip *nand_chip = mtd->priv;
+ struct mxc_nand_host *host = nand_chip->priv;
+ int bufs, i;
- writew(NFC_INPUT, host->regs + NFC_CONFIG2);
+ if (nfc_is_v1() && mtd->writesize > 512)
+ bufs = 4;
+ else
+ bufs = 1;
- /* Wait for operation to complete */
- wait_op_done(host, TROP_US_DELAY, spare_only, true);
-}
+ for (i = 0; i < bufs; i++) {
-/* Requests NANDFC to initated the transfer of data from the
- * NAND device into in the NANDFC ram buffer. */
-static void send_read_page(struct mxc_nand_host *host, uint8_t buf_id,
- int spare_only)
-{
- DEBUG(MTD_DEBUG_LEVEL3, "send_read_page (%d)\n", spare_only);
+ /* NANDFC buffer 0 is used for page read/write */
+ writew(i, host->regs + NFC_BUF_ADDR);
- /* NANDFC buffer 0 is used for page read/write */
- writew(buf_id, host->regs + NFC_BUF_ADDR);
+ writew(ops, host->regs + NFC_CONFIG2);
- /* Configure spare or page+spare access */
- if (!host->pagesize_2k) {
- uint32_t config1 = readw(host->regs + NFC_CONFIG1);
- if (spare_only)
- config1 |= NFC_SP_EN;
- else
- config1 &= ~NFC_SP_EN;
- writew(config1, host->regs + NFC_CONFIG1);
+ /* Wait for operation to complete */
+ wait_op_done(host, true);
}
-
- writew(NFC_OUTPUT, host->regs + NFC_CONFIG2);
-
- /* Wait for operation to complete */
- wait_op_done(host, TROP_US_DELAY, spare_only, true);
}
/* Request the NANDFC to perform a read of the NAND device ID. */
static void send_read_id(struct mxc_nand_host *host)
{
struct nand_chip *this = &host->nand;
- uint16_t tmp;
/* NANDFC buffer 0 is used for device ID output */
writew(0x0, host->regs + NFC_BUF_ADDR);
- /* Read ID into main buffer */
- tmp = readw(host->regs + NFC_CONFIG1);
- tmp &= ~NFC_SP_EN;
- writew(tmp, host->regs + NFC_CONFIG1);
-
writew(NFC_ID, host->regs + NFC_CONFIG2);
/* Wait for operation to complete */
- wait_op_done(host, TROP_US_DELAY, 0, true);
+ wait_op_done(host, true);
if (this->options & NAND_BUSWIDTH_16) {
- void __iomem *main_buf = host->regs + MAIN_AREA0;
+ void __iomem *main_buf = host->main_area0;
/* compress the ID info */
writeb(readb(main_buf + 2), main_buf + 1);
writeb(readb(main_buf + 4), main_buf + 2);
@@ -312,15 +289,16 @@ static void send_read_id(struct mxc_nand_host *host)
writeb(readb(main_buf + 8), main_buf + 4);
writeb(readb(main_buf + 10), main_buf + 5);
}
+ memcpy(host->data_buf, host->main_area0, 16);
}
/* This function requests the NANDFC to perform a read of the
* NAND device status and returns the current status. */
static uint16_t get_dev_status(struct mxc_nand_host *host)
{
- void __iomem *main_buf = host->regs + MAIN_AREA1;
+ void __iomem *main_buf = host->main_area1;
uint32_t store;
- uint16_t ret, tmp;
+ uint16_t ret;
/* Issue status request to NAND device */
/* store the main area1 first word, later do recovery */
@@ -329,15 +307,10 @@ static uint16_t get_dev_status(struct mxc_nand_host *host)
* corruption of read/write buffer on status requests. */
writew(1, host->regs + NFC_BUF_ADDR);
- /* Read status into main buffer */
- tmp = readw(host->regs + NFC_CONFIG1);
- tmp &= ~NFC_SP_EN;
- writew(tmp, host->regs + NFC_CONFIG1);
-
writew(NFC_STATUS, host->regs + NFC_CONFIG2);
/* Wait for operation to complete */
- wait_op_done(host, TROP_US_DELAY, 0, true);
+ wait_op_done(host, true);
/* Status is placed in first word of main buffer */
/* get status, then recovery area 1 data */
@@ -397,32 +370,14 @@ static u_char mxc_nand_read_byte(struct mtd_info *mtd)
{
struct nand_chip *nand_chip = mtd->priv;
struct mxc_nand_host *host = nand_chip->priv;
- uint8_t ret = 0;
- uint16_t col, rd_word;
- uint16_t __iomem *main_buf = host->regs + MAIN_AREA0;
- uint16_t __iomem *spare_buf = host->regs + SPARE_AREA0;
+ uint8_t ret;
/* Check for status request */
if (host->status_request)
return get_dev_status(host) & 0xFF;
- /* Get column for 16-bit access */
- col = host->col_addr >> 1;
-
- /* If we are accessing the spare region */
- if (host->spare_only)
- rd_word = readw(&spare_buf[col]);
- else
- rd_word = readw(&main_buf[col]);
-
- /* Pick upper/lower byte of word from RAM buffer */
- if (host->col_addr & 0x1)
- ret = (rd_word >> 8) & 0xFF;
- else
- ret = rd_word & 0xFF;
-
- /* Update saved column address */
- host->col_addr++;
+ ret = *(uint8_t *)(host->data_buf + host->buf_start);
+ host->buf_start++;
return ret;
}
@@ -431,33 +386,10 @@ static uint16_t mxc_nand_read_word(struct mtd_info *mtd)
{
struct nand_chip *nand_chip = mtd->priv;
struct mxc_nand_host *host = nand_chip->priv;
- uint16_t col, rd_word, ret;
- uint16_t __iomem *p;
-
- DEBUG(MTD_DEBUG_LEVEL3,
- "mxc_nand_read_word(col = %d)\n", host->col_addr);
-
- col = host->col_addr;
- /* Adjust saved column address */
- if (col < mtd->writesize && host->spare_only)
- col += mtd->writesize;
+ uint16_t ret;
- if (col < mtd->writesize)
- p = (host->regs + MAIN_AREA0) + (col >> 1);
- else
- p = (host->regs + SPARE_AREA0) + ((col - mtd->writesize) >> 1);
-
- if (col & 1) {
- rd_word = readw(p);
- ret = (rd_word >> 8) & 0xff;
- rd_word = readw(&p[1]);
- ret |= (rd_word << 8) & 0xff00;
-
- } else
- ret = readw(p);
-
- /* Update saved column address */
- host->col_addr = col + 2;
+ ret = *(uint16_t *)(host->data_buf + host->buf_start);
+ host->buf_start += 2;
return ret;
}
@@ -470,94 +402,14 @@ static void mxc_nand_write_buf(struct mtd_info *mtd,
{
struct nand_chip *nand_chip = mtd->priv;
struct mxc_nand_host *host = nand_chip->priv;
- int n, col, i = 0;
-
- DEBUG(MTD_DEBUG_LEVEL3,
- "mxc_nand_write_buf(col = %d, len = %d)\n", host->col_addr,
- len);
-
- col = host->col_addr;
+ u16 col = host->buf_start;
+ int n = mtd->oobsize + mtd->writesize - col;
- /* Adjust saved column address */
- if (col < mtd->writesize && host->spare_only)
- col += mtd->writesize;
+ n = min(n, len);
- n = mtd->writesize + mtd->oobsize - col;
- n = min(len, n);
-
- DEBUG(MTD_DEBUG_LEVEL3,
- "%s:%d: col = %d, n = %d\n", __func__, __LINE__, col, n);
-
- while (n) {
- void __iomem *p;
-
- if (col < mtd->writesize)
- p = host->regs + MAIN_AREA0 + (col & ~3);
- else
- p = host->regs + SPARE_AREA0 -
- mtd->writesize + (col & ~3);
-
- DEBUG(MTD_DEBUG_LEVEL3, "%s:%d: p = %p\n", __func__,
- __LINE__, p);
-
- if (((col | (int)&buf[i]) & 3) || n < 16) {
- uint32_t data = 0;
-
- if (col & 3 || n < 4)
- data = readl(p);
-
- switch (col & 3) {
- case 0:
- if (n) {
- data = (data & 0xffffff00) |
- (buf[i++] << 0);
- n--;
- col++;
- }
- case 1:
- if (n) {
- data = (data & 0xffff00ff) |
- (buf[i++] << 8);
- n--;
- col++;
- }
- case 2:
- if (n) {
- data = (data & 0xff00ffff) |
- (buf[i++] << 16);
- n--;
- col++;
- }
- case 3:
- if (n) {
- data = (data & 0x00ffffff) |
- (buf[i++] << 24);
- n--;
- col++;
- }
- }
-
- writel(data, p);
- } else {
- int m = mtd->writesize - col;
+ memcpy(host->data_buf + col, buf, n);
- if (col >= mtd->writesize)
- m += mtd->oobsize;
-
- m = min(n, m) & ~3;
-
- DEBUG(MTD_DEBUG_LEVEL3,
- "%s:%d: n = %d, m = %d, i = %d, col = %d\n",
- __func__, __LINE__, n, m, i, col);
-
- memcpy(p, &buf[i], m);
- col += m;
- i += m;
- n -= m;
- }
- }
- /* Update saved column address */
- host->col_addr = col;
+ host->buf_start += n;
}
/* Read the data buffer from the NAND Flash. To read the data from NAND
@@ -568,75 +420,14 @@ static void mxc_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len)
{
struct nand_chip *nand_chip = mtd->priv;
struct mxc_nand_host *host = nand_chip->priv;
- int n, col, i = 0;
-
- DEBUG(MTD_DEBUG_LEVEL3,
- "mxc_nand_read_buf(col = %d, len = %d)\n", host->col_addr, len);
-
- col = host->col_addr;
+ u16 col = host->buf_start;
+ int n = mtd->oobsize + mtd->writesize - col;
- /* Adjust saved column address */
- if (col < mtd->writesize && host->spare_only)
- col += mtd->writesize;
+ n = min(n, len);
- n = mtd->writesize + mtd->oobsize - col;
- n = min(len, n);
-
- while (n) {
- void __iomem *p;
-
- if (col < mtd->writesize)
- p = host->regs + MAIN_AREA0 + (col & ~3);
- else
- p = host->regs + SPARE_AREA0 -
- mtd->writesize + (col & ~3);
-
- if (((col | (int)&buf[i]) & 3) || n < 16) {
- uint32_t data;
-
- data = readl(p);
- switch (col & 3) {
- case 0:
- if (n) {
- buf[i++] = (uint8_t) (data);
- n--;
- col++;
- }
- case 1:
- if (n) {
- buf[i++] = (uint8_t) (data >> 8);
- n--;
- col++;
- }
- case 2:
- if (n) {
- buf[i++] = (uint8_t) (data >> 16);
- n--;
- col++;
- }
- case 3:
- if (n) {
- buf[i++] = (uint8_t) (data >> 24);
- n--;
- col++;
- }
- }
- } else {
- int m = mtd->writesize - col;
-
- if (col >= mtd->writesize)
- m += mtd->oobsize;
-
- m = min(n, m) & ~3;
- memcpy(&buf[i], p, m);
- col += m;
- i += m;
- n -= m;
- }
- }
- /* Update saved column address */
- host->col_addr = col;
+ memcpy(buf, host->data_buf + col, len);
+ host->buf_start += len;
}
/* Used by the upper layer to verify the data in NAND Flash
@@ -654,23 +445,6 @@ static void mxc_nand_select_chip(struct mtd_info *mtd, int chip)
struct nand_chip *nand_chip = mtd->priv;
struct mxc_nand_host *host = nand_chip->priv;
-#ifdef CONFIG_MTD_NAND_MXC_FORCE_CE
- if (chip > 0) {
- DEBUG(MTD_DEBUG_LEVEL0,
- "ERROR: Illegal chip select (chip = %d)\n", chip);
- return;
- }
-
- if (chip == -1) {
- writew(readw(host->regs + NFC_CONFIG1) & ~NFC_CE,
- host->regs + NFC_CONFIG1);
- return;
- }
-
- writew(readw(host->regs + NFC_CONFIG1) | NFC_CE,
- host->regs + NFC_CONFIG1);
-#endif
-
switch (chip) {
case -1:
/* Disable the NFC clock */
@@ -692,94 +466,40 @@ static void mxc_nand_select_chip(struct mtd_info *mtd, int chip)
}
}
-/* Used by the upper layer to write command to NAND Flash for
- * different operations to be carried out on NAND Flash */
-static void mxc_nand_command(struct mtd_info *mtd, unsigned command,
- int column, int page_addr)
+/*
+ * Function to transfer data to/from spare area.
+ */
+static void copy_spare(struct mtd_info *mtd, bool bfrom)
{
- struct nand_chip *nand_chip = mtd->priv;
- struct mxc_nand_host *host = nand_chip->priv;
- int useirq = true;
-
- DEBUG(MTD_DEBUG_LEVEL3,
- "mxc_nand_command (cmd = 0x%x, col = 0x%x, page = 0x%x)\n",
- command, column, page_addr);
-
- /* Reset command state information */
- host->status_request = false;
-
- /* Command pre-processing step */
- switch (command) {
-
- case NAND_CMD_STATUS:
- host->col_addr = 0;
- host->status_request = true;
- break;
-
- case NAND_CMD_READ0:
- host->col_addr = column;
- host->spare_only = false;
- useirq = false;
- break;
-
- case NAND_CMD_READOOB:
- host->col_addr = column;
- host->spare_only = true;
- useirq = false;
- if (host->pagesize_2k)
- command = NAND_CMD_READ0; /* only READ0 is valid */
- break;
-
- case NAND_CMD_SEQIN:
- if (column >= mtd->writesize) {
- /*
- * FIXME: before send SEQIN command for write OOB,
- * We must read one page out.
- * For K9F1GXX has no READ1 command to set current HW
- * pointer to spare area, we must write the whole page
- * including OOB together.
- */
- if (host->pagesize_2k)
- /* call ourself to read a page */
- mxc_nand_command(mtd, NAND_CMD_READ0, 0,
- page_addr);
-
- host->col_addr = column - mtd->writesize;
- host->spare_only = true;
-
- /* Set program pointer to spare region */
- if (!host->pagesize_2k)
- send_cmd(host, NAND_CMD_READOOB, false);
- } else {
- host->spare_only = false;
- host->col_addr = column;
-
- /* Set program pointer to page start */
- if (!host->pagesize_2k)
- send_cmd(host, NAND_CMD_READ0, false);
- }
- useirq = false;
- break;
-
- case NAND_CMD_PAGEPROG:
- send_prog_page(host, 0, host->spare_only);
-
- if (host->pagesize_2k) {
- /* data in 4 areas datas */
- send_prog_page(host, 1, host->spare_only);
- send_prog_page(host, 2, host->spare_only);
- send_prog_page(host, 3, host->spare_only);
- }
-
- break;
+ struct nand_chip *this = mtd->priv;
+ struct mxc_nand_host *host = this->priv;
+ u16 i, j;
+ u16 n = mtd->writesize >> 9;
+ u8 *d = host->data_buf + mtd->writesize;
+ u8 *s = host->spare0;
+ u16 t = host->spare_len;
+
+ j = (mtd->oobsize / n >> 1) << 1;
+
+ if (bfrom) {
+ for (i = 0; i < n - 1; i++)
+ memcpy(d + i * j, s + i * t, j);
+
+ /* the last section */
+ memcpy(d + i * j, s + i * t, mtd->oobsize - i * j);
+ } else {
+ for (i = 0; i < n - 1; i++)
+ memcpy(&s[i * t], &d[i * j], j);
- case NAND_CMD_ERASE1:
- useirq = false;
- break;
+ /* the last section */
+ memcpy(&s[i * t], &d[i * j], mtd->oobsize - i * j);
}
+}
- /* Write out the command to the device. */
- send_cmd(host, command, useirq);
+static void mxc_do_addr_cycle(struct mtd_info *mtd, int column, int page_addr)
+{
+ struct nand_chip *nand_chip = mtd->priv;
+ struct mxc_nand_host *host = nand_chip->priv;
/* Write out column address, if necessary */
if (column != -1) {
@@ -791,7 +511,7 @@ static void mxc_nand_command(struct mtd_info *mtd, unsigned command,
* the full page.
*/
send_addr(host, 0, page_addr == -1);
- if (host->pagesize_2k)
+ if (mtd->writesize > 512)
/* another col addr cycle for 2k page */
send_addr(host, 0, false);
}
@@ -801,7 +521,7 @@ static void mxc_nand_command(struct mtd_info *mtd, unsigned command,
/* paddr_0 - p_addr_7 */
send_addr(host, (page_addr & 0xff), false);
- if (host->pagesize_2k) {
+ if (mtd->writesize > 512) {
if (mtd->size >= 0x10000000) {
/* paddr_8 - paddr_15 */
send_addr(host, (page_addr >> 8) & 0xff, false);
@@ -820,52 +540,136 @@ static void mxc_nand_command(struct mtd_info *mtd, unsigned command,
send_addr(host, (page_addr >> 8) & 0xff, true);
}
}
+}
+
+/* Used by the upper layer to write command to NAND Flash for
+ * different operations to be carried out on NAND Flash */
+static void mxc_nand_command(struct mtd_info *mtd, unsigned command,
+ int column, int page_addr)
+{
+ struct nand_chip *nand_chip = mtd->priv;
+ struct mxc_nand_host *host = nand_chip->priv;
+
+ DEBUG(MTD_DEBUG_LEVEL3,
+ "mxc_nand_command (cmd = 0x%x, col = 0x%x, page = 0x%x)\n",
+ command, column, page_addr);
+
+ /* Reset command state information */
+ host->status_request = false;
- /* Command post-processing step */
+ /* Command pre-processing step */
switch (command) {
- case NAND_CMD_RESET:
+ case NAND_CMD_STATUS:
+ host->buf_start = 0;
+ host->status_request = true;
+
+ send_cmd(host, command, true);
+ mxc_do_addr_cycle(mtd, column, page_addr);
break;
- case NAND_CMD_READOOB:
case NAND_CMD_READ0:
- if (host->pagesize_2k) {
- /* send read confirm command */
+ case NAND_CMD_READOOB:
+ if (command == NAND_CMD_READ0)
+ host->buf_start = column;
+ else
+ host->buf_start = column + mtd->writesize;
+
+ if (mtd->writesize > 512)
+ command = NAND_CMD_READ0; /* only READ0 is valid */
+
+ send_cmd(host, command, false);
+ mxc_do_addr_cycle(mtd, column, page_addr);
+
+ if (mtd->writesize > 512)
send_cmd(host, NAND_CMD_READSTART, true);
- /* read for each AREA */
- send_read_page(host, 0, host->spare_only);
- send_read_page(host, 1, host->spare_only);
- send_read_page(host, 2, host->spare_only);
- send_read_page(host, 3, host->spare_only);
- } else
- send_read_page(host, 0, host->spare_only);
+
+ send_page(mtd, NFC_OUTPUT);
+
+ memcpy(host->data_buf, host->main_area0, mtd->writesize);
+ copy_spare(mtd, true);
break;
- case NAND_CMD_READID:
- host->col_addr = 0;
- send_read_id(host);
+ case NAND_CMD_SEQIN:
+ if (column >= mtd->writesize) {
+ /*
+ * FIXME: before send SEQIN command for write OOB,
+ * We must read one page out.
+ * For K9F1GXX has no READ1 command to set current HW
+ * pointer to spare area, we must write the whole page
+ * including OOB together.
+ */
+ if (mtd->writesize > 512)
+ /* call ourself to read a page */
+ mxc_nand_command(mtd, NAND_CMD_READ0, 0,
+ page_addr);
+
+ host->buf_start = column;
+
+ /* Set program pointer to spare region */
+ if (mtd->writesize == 512)
+ send_cmd(host, NAND_CMD_READOOB, false);
+ } else {
+ host->buf_start = column;
+
+ /* Set program pointer to page start */
+ if (mtd->writesize == 512)
+ send_cmd(host, NAND_CMD_READ0, false);
+ }
+
+ send_cmd(host, command, false);
+ mxc_do_addr_cycle(mtd, column, page_addr);
break;
case NAND_CMD_PAGEPROG:
+ memcpy(host->main_area0, host->data_buf, mtd->writesize);
+ copy_spare(mtd, false);
+ send_page(mtd, NFC_INPUT);
+ send_cmd(host, command, true);
+ mxc_do_addr_cycle(mtd, column, page_addr);
break;
- case NAND_CMD_STATUS:
+ case NAND_CMD_READID:
+ send_cmd(host, command, true);
+ mxc_do_addr_cycle(mtd, column, page_addr);
+ send_read_id(host);
+ host->buf_start = column;
break;
+ case NAND_CMD_ERASE1:
case NAND_CMD_ERASE2:
+ send_cmd(host, command, false);
+ mxc_do_addr_cycle(mtd, column, page_addr);
+
break;
}
}
-/* Define some generic bad / good block scan pattern which are used
- * while scanning a device for factory marked good / bad blocks. */
-static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
+/*
+ * The generic flash bbt decriptors overlap with our ecc
+ * hardware, so define some i.MX specific ones.
+ */
+static uint8_t bbt_pattern[] = { 'B', 'b', 't', '0' };
+static uint8_t mirror_pattern[] = { '1', 't', 'b', 'B' };
+
+static struct nand_bbt_descr bbt_main_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+ | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+ .offs = 0,
+ .len = 4,
+ .veroffs = 4,
+ .maxblocks = 4,
+ .pattern = bbt_pattern,
+};
-static struct nand_bbt_descr smallpage_memorybased = {
- .options = NAND_BBT_SCAN2NDPAGE,
- .offs = 5,
- .len = 1,
- .pattern = scan_ff_pattern
+static struct nand_bbt_descr bbt_mirror_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+ | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+ .offs = 0,
+ .len = 4,
+ .veroffs = 4,
+ .maxblocks = 4,
+ .pattern = mirror_pattern,
};
static int __init mxcnd_probe(struct platform_device *pdev)
@@ -877,12 +681,16 @@ static int __init mxcnd_probe(struct platform_device *pdev)
struct resource *res;
uint16_t tmp;
int err = 0, nr_parts = 0;
+ struct nand_ecclayout *oob_smallpage, *oob_largepage;
/* Allocate memory for MTD device structure and private data */
- host = kzalloc(sizeof(struct mxc_nand_host), GFP_KERNEL);
+ host = kzalloc(sizeof(struct mxc_nand_host) + NAND_MAX_PAGESIZE +
+ NAND_MAX_OOBSIZE, GFP_KERNEL);
if (!host)
return -ENOMEM;
+ host->data_buf = (uint8_t *)(host + 1);
+
host->dev = &pdev->dev;
/* structures must be linked */
this = &host->nand;
@@ -890,7 +698,7 @@ static int __init mxcnd_probe(struct platform_device *pdev)
mtd->priv = this;
mtd->owner = THIS_MODULE;
mtd->dev.parent = &pdev->dev;
- mtd->name = "mxc_nand";
+ mtd->name = DRIVER_NAME;
/* 50 us command delay time */
this->chip_delay = 5;
@@ -920,62 +728,93 @@ static int __init mxcnd_probe(struct platform_device *pdev)
goto eres;
}
- host->regs = ioremap(res->start, res->end - res->start + 1);
- if (!host->regs) {
+ host->base = ioremap(res->start, resource_size(res));
+ if (!host->base) {
err = -ENOMEM;
goto eres;
}
+ host->main_area0 = host->base;
+ host->main_area1 = host->base + 0x200;
+
+ if (nfc_is_v21()) {
+ host->regs = host->base + 0x1000;
+ host->spare0 = host->base + 0x1000;
+ host->spare_len = 64;
+ oob_smallpage = &nandv2_hw_eccoob_smallpage;
+ oob_largepage = &nandv2_hw_eccoob_largepage;
+ } else if (nfc_is_v1()) {
+ host->regs = host->base;
+ host->spare0 = host->base + 0x800;
+ host->spare_len = 16;
+ oob_smallpage = &nandv1_hw_eccoob_smallpage;
+ oob_largepage = &nandv1_hw_eccoob_largepage;
+ } else
+ BUG();
+
+ /* disable interrupt and spare enable */
tmp = readw(host->regs + NFC_CONFIG1);
tmp |= NFC_INT_MSK;
+ tmp &= ~NFC_SP_EN;
writew(tmp, host->regs + NFC_CONFIG1);
init_waitqueue_head(&host->irq_waitq);
host->irq = platform_get_irq(pdev, 0);
- err = request_irq(host->irq, mxc_nfc_irq, 0, "mxc_nd", host);
+ err = request_irq(host->irq, mxc_nfc_irq, 0, DRIVER_NAME, host);
if (err)
goto eirq;
+ /* Reset NAND */
+ this->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+
+ /* preset operation */
+ /* Unlock the internal RAM Buffer */
+ writew(0x2, host->regs + NFC_CONFIG);
+
+ /* Blocks to be unlocked */
+ if (nfc_is_v21()) {
+ writew(0x0, host->regs + NFC_V21_UNLOCKSTART_BLKADDR);
+ writew(0xffff, host->regs + NFC_V21_UNLOCKEND_BLKADDR);
+ this->ecc.bytes = 9;
+ } else if (nfc_is_v1()) {
+ writew(0x0, host->regs + NFC_V1_UNLOCKSTART_BLKADDR);
+ writew(0x4000, host->regs + NFC_V1_UNLOCKEND_BLKADDR);
+ this->ecc.bytes = 3;
+ } else
+ BUG();
+
+ /* Unlock Block Command for given address range */
+ writew(0x4, host->regs + NFC_WRPROT);
+
+ this->ecc.size = 512;
+ this->ecc.layout = oob_smallpage;
+
if (pdata->hw_ecc) {
this->ecc.calculate = mxc_nand_calculate_ecc;
this->ecc.hwctl = mxc_nand_enable_hwecc;
this->ecc.correct = mxc_nand_correct_data;
this->ecc.mode = NAND_ECC_HW;
- this->ecc.size = 512;
- this->ecc.bytes = 3;
tmp = readw(host->regs + NFC_CONFIG1);
tmp |= NFC_ECC_EN;
writew(tmp, host->regs + NFC_CONFIG1);
} else {
- this->ecc.size = 512;
- this->ecc.bytes = 3;
- this->ecc.layout = &nand_hw_eccoob_8;
this->ecc.mode = NAND_ECC_SOFT;
tmp = readw(host->regs + NFC_CONFIG1);
tmp &= ~NFC_ECC_EN;
writew(tmp, host->regs + NFC_CONFIG1);
}
- /* Reset NAND */
- this->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
-
- /* preset operation */
- /* Unlock the internal RAM Buffer */
- writew(0x2, host->regs + NFC_CONFIG);
-
- /* Blocks to be unlocked */
- writew(0x0, host->regs + NFC_UNLOCKSTART_BLKADDR);
- writew(0x4000, host->regs + NFC_UNLOCKEND_BLKADDR);
-
- /* Unlock Block Command for given address range */
- writew(0x4, host->regs + NFC_WRPROT);
-
/* NAND bus width determines access funtions used by upper layer */
- if (pdata->width == 2) {
+ if (pdata->width == 2)
this->options |= NAND_BUSWIDTH_16;
- this->ecc.layout = &nand_hw_eccoob_16;
+
+ if (pdata->flash_bbt) {
+ this->bbt_td = &bbt_main_descr;
+ this->bbt_md = &bbt_mirror_descr;
+ /* update flash based bbt */
+ this->options |= NAND_USE_FLASH_BBT;
}
/* first scan to find the device and get the page size */
@@ -984,38 +823,8 @@ static int __init mxcnd_probe(struct platform_device *pdev)
goto escan;
}
- if (mtd->writesize == 2048) {
- host->pagesize_2k = 1;
- this->badblock_pattern = &smallpage_memorybased;
- }
-
- if (this->ecc.mode == NAND_ECC_HW) {
- switch (mtd->oobsize) {
- case 8:
- this->ecc.layout = &nand_hw_eccoob_8;
- break;
- case 16:
- this->ecc.layout = &nand_hw_eccoob_16;
- break;
- case 64:
- this->ecc.layout = &nand_hw_eccoob_64;
- break;
- default:
- /* page size not handled by HW ECC */
- /* switching back to soft ECC */
- this->ecc.size = 512;
- this->ecc.bytes = 3;
- this->ecc.layout = &nand_hw_eccoob_8;
- this->ecc.mode = NAND_ECC_SOFT;
- this->ecc.calculate = NULL;
- this->ecc.correct = NULL;
- this->ecc.hwctl = NULL;
- tmp = readw(host->regs + NFC_CONFIG1);
- tmp &= ~NFC_ECC_EN;
- writew(tmp, host->regs + NFC_CONFIG1);
- break;
- }
- }
+ if (mtd->writesize == 2048)
+ this->ecc.layout = oob_largepage;
/* second phase scan */
if (nand_scan_tail(mtd)) {
@@ -1043,7 +852,7 @@ static int __init mxcnd_probe(struct platform_device *pdev)
escan:
free_irq(host->irq, host);
eirq:
- iounmap(host->regs);
+ iounmap(host->base);
eres:
clk_put(host->clk);
eclk:
@@ -1062,7 +871,7 @@ static int __devexit mxcnd_remove(struct platform_device *pdev)
nand_release(&host->mtd);
free_irq(host->irq, host);
- iounmap(host->regs);
+ iounmap(host->base);
kfree(host);
return 0;
@@ -1113,7 +922,7 @@ static struct platform_driver mxcnd_driver = {
.driver = {
.name = DRIVER_NAME,
},
- .remove = __exit_p(mxcnd_remove),
+ .remove = __devexit_p(mxcnd_remove),
.suspend = mxcnd_suspend,
.resume = mxcnd_resume,
};
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 2957cc70da3..8f2958fe214 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -428,6 +428,28 @@ static int nand_block_checkbad(struct mtd_info *mtd, loff_t ofs, int getchip,
return nand_isbad_bbt(mtd, ofs, allowbbt);
}
+/**
+ * panic_nand_wait_ready - [GENERIC] Wait for the ready pin after commands.
+ * @mtd: MTD device structure
+ * @timeo: Timeout
+ *
+ * Helper function for nand_wait_ready used when needing to wait in interrupt
+ * context.
+ */
+static void panic_nand_wait_ready(struct mtd_info *mtd, unsigned long timeo)
+{
+ struct nand_chip *chip = mtd->priv;
+ int i;
+
+ /* Wait for the device to get ready */
+ for (i = 0; i < timeo; i++) {
+ if (chip->dev_ready(mtd))
+ break;
+ touch_softlockup_watchdog();
+ mdelay(1);
+ }
+}
+
/*
* Wait for the ready pin, after a command
* The timeout is catched later.
@@ -437,6 +459,10 @@ void nand_wait_ready(struct mtd_info *mtd)
struct nand_chip *chip = mtd->priv;
unsigned long timeo = jiffies + 2;
+ /* 400ms timeout */
+ if (in_interrupt() || oops_in_progress)
+ return panic_nand_wait_ready(mtd, 400);
+
led_trigger_event(nand_led_trigger, LED_FULL);
/* wait until command is processed or timeout occures */
do {
@@ -672,6 +698,22 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
}
/**
+ * panic_nand_get_device - [GENERIC] Get chip for selected access
+ * @chip: the nand chip descriptor
+ * @mtd: MTD device structure
+ * @new_state: the state which is requested
+ *
+ * Used when in panic, no locks are taken.
+ */
+static void panic_nand_get_device(struct nand_chip *chip,
+ struct mtd_info *mtd, int new_state)
+{
+ /* Hardware controller shared among independend devices */
+ chip->controller->active = chip;
+ chip->state = new_state;
+}
+
+/**
* nand_get_device - [GENERIC] Get chip for selected access
* @chip: the nand chip descriptor
* @mtd: MTD device structure
@@ -698,8 +740,14 @@ nand_get_device(struct nand_chip *chip, struct mtd_info *mtd, int new_state)
return 0;
}
if (new_state == FL_PM_SUSPENDED) {
- spin_unlock(lock);
- return (chip->state == FL_PM_SUSPENDED) ? 0 : -EAGAIN;
+ if (chip->controller->active->state == FL_PM_SUSPENDED) {
+ chip->state = FL_PM_SUSPENDED;
+ spin_unlock(lock);
+ return 0;
+ } else {
+ spin_unlock(lock);
+ return -EAGAIN;
+ }
}
set_current_state(TASK_UNINTERRUPTIBLE);
add_wait_queue(wq, &wait);
@@ -710,6 +758,32 @@ nand_get_device(struct nand_chip *chip, struct mtd_info *mtd, int new_state)
}
/**
+ * panic_nand_wait - [GENERIC] wait until the command is done
+ * @mtd: MTD device structure
+ * @chip: NAND chip structure
+ * @timeo: Timeout
+ *
+ * Wait for command done. This is a helper function for nand_wait used when
+ * we are in interrupt context. May happen when in panic and trying to write
+ * an oops trough mtdoops.
+ */
+static void panic_nand_wait(struct mtd_info *mtd, struct nand_chip *chip,
+ unsigned long timeo)
+{
+ int i;
+ for (i = 0; i < timeo; i++) {
+ if (chip->dev_ready) {
+ if (chip->dev_ready(mtd))
+ break;
+ } else {
+ if (chip->read_byte(mtd) & NAND_STATUS_READY)
+ break;
+ }
+ mdelay(1);
+ }
+}
+
+/**
* nand_wait - [DEFAULT] wait until the command is done
* @mtd: MTD device structure
* @chip: NAND chip structure
@@ -740,15 +814,19 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip)
else
chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
- while (time_before(jiffies, timeo)) {
- if (chip->dev_ready) {
- if (chip->dev_ready(mtd))
- break;
- } else {
- if (chip->read_byte(mtd) & NAND_STATUS_READY)
- break;
+ if (in_interrupt() || oops_in_progress)
+ panic_nand_wait(mtd, chip, timeo);
+ else {
+ while (time_before(jiffies, timeo)) {
+ if (chip->dev_ready) {
+ if (chip->dev_ready(mtd))
+ break;
+ } else {
+ if (chip->read_byte(mtd) & NAND_STATUS_READY)
+ break;
+ }
+ cond_resched();
}
- cond_resched();
}
led_trigger_event(nand_led_trigger, LED_OFF);
@@ -1949,6 +2027,45 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
}
/**
+ * panic_nand_write - [MTD Interface] NAND write with ECC
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @len: number of bytes to write
+ * @retlen: pointer to variable to store the number of written bytes
+ * @buf: the data to write
+ *
+ * NAND write with ECC. Used when performing writes in interrupt context, this
+ * may for example be called by mtdoops when writing an oops while in panic.
+ */
+static int panic_nand_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const uint8_t *buf)
+{
+ struct nand_chip *chip = mtd->priv;
+ int ret;
+
+ /* Do not allow reads past end of device */
+ if ((to + len) > mtd->size)
+ return -EINVAL;
+ if (!len)
+ return 0;
+
+ /* Wait for the device to get ready. */
+ panic_nand_wait(mtd, chip, 400);
+
+ /* Grab the device. */
+ panic_nand_get_device(chip, mtd, FL_WRITING);
+
+ chip->ops.len = len;
+ chip->ops.datbuf = (uint8_t *)buf;
+ chip->ops.oobbuf = NULL;
+
+ ret = nand_do_write_ops(mtd, to, &chip->ops);
+
+ *retlen = chip->ops.retlen;
+ return ret;
+}
+
+/**
* nand_write - [MTD Interface] NAND write with ECC
* @mtd: MTD device structure
* @to: offset to write to
@@ -2645,7 +2762,8 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips)
type = nand_get_flash_type(mtd, chip, busw, &nand_maf_id);
if (IS_ERR(type)) {
- printk(KERN_WARNING "No NAND device found!!!\n");
+ if (!(chip->options & NAND_SCAN_SILENT_NODEV))
+ printk(KERN_WARNING "No NAND device found.\n");
chip->select_chip(mtd, -1);
return PTR_ERR(type);
}
@@ -2877,6 +2995,7 @@ int nand_scan_tail(struct mtd_info *mtd)
mtd->unpoint = NULL;
mtd->read = nand_read;
mtd->write = nand_write;
+ mtd->panic_write = panic_nand_write;
mtd->read_oob = nand_read_oob;
mtd->write_oob = nand_write_oob;
mtd->sync = nand_sync;
diff --git a/drivers/mtd/nand/nand_bcm_umi.c b/drivers/mtd/nand/nand_bcm_umi.c
new file mode 100644
index 00000000000..46a6bc9c4b7
--- /dev/null
+++ b/drivers/mtd/nand/nand_bcm_umi.c
@@ -0,0 +1,149 @@
+/*****************************************************************************
+* Copyright 2004 - 2009 Broadcom Corporation. All rights reserved.
+*
+* Unless you and Broadcom execute a separate written software license
+* agreement governing use of this software, this software is licensed to you
+* under the terms of the GNU General Public License version 2, available at
+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
+*
+* Notwithstanding the above, under no circumstances may you combine this
+* software in any way with any other Broadcom software provided under a
+* license other than the GPL, without Broadcom's express prior written
+* consent.
+*****************************************************************************/
+
+/* ---- Include Files ---------------------------------------------------- */
+#include <mach/reg_umi.h>
+#include "nand_bcm_umi.h"
+#ifdef BOOT0_BUILD
+#include <uart.h>
+#endif
+
+/* ---- External Variable Declarations ----------------------------------- */
+/* ---- External Function Prototypes ------------------------------------- */
+/* ---- Public Variables ------------------------------------------------- */
+/* ---- Private Constants and Types -------------------------------------- */
+/* ---- Private Function Prototypes -------------------------------------- */
+/* ---- Private Variables ------------------------------------------------ */
+/* ---- Private Functions ------------------------------------------------ */
+
+#if NAND_ECC_BCH
+/****************************************************************************
+* nand_bch_ecc_flip_bit - Routine to flip an errored bit
+*
+* PURPOSE:
+* This is a helper routine that flips the bit (0 -> 1 or 1 -> 0) of the
+* errored bit specified
+*
+* PARAMETERS:
+* datap - Container that holds the 512 byte data
+* errorLocation - Location of the bit that needs to be flipped
+*
+* RETURNS:
+* None
+****************************************************************************/
+static void nand_bcm_umi_bch_ecc_flip_bit(uint8_t *datap, int errorLocation)
+{
+ int locWithinAByte = (errorLocation & REG_UMI_BCH_ERR_LOC_BYTE) >> 0;
+ int locWithinAWord = (errorLocation & REG_UMI_BCH_ERR_LOC_WORD) >> 3;
+ int locWithinAPage = (errorLocation & REG_UMI_BCH_ERR_LOC_PAGE) >> 5;
+
+ uint8_t errorByte = 0;
+ uint8_t byteMask = 1 << locWithinAByte;
+
+ /* BCH uses big endian, need to change the location
+ * bits to little endian */
+ locWithinAWord = 3 - locWithinAWord;
+
+ errorByte = datap[locWithinAPage * sizeof(uint32_t) + locWithinAWord];
+
+#ifdef BOOT0_BUILD
+ puthexs("\nECC Correct Offset: ",
+ locWithinAPage * sizeof(uint32_t) + locWithinAWord);
+ puthexs(" errorByte:", errorByte);
+ puthex8(" Bit: ", locWithinAByte);
+#endif
+
+ if (errorByte & byteMask) {
+ /* bit needs to be cleared */
+ errorByte &= ~byteMask;
+ } else {
+ /* bit needs to be set */
+ errorByte |= byteMask;
+ }
+
+ /* write back the value with the fixed bit */
+ datap[locWithinAPage * sizeof(uint32_t) + locWithinAWord] = errorByte;
+}
+
+/****************************************************************************
+* nand_correct_page_bch - Routine to correct bit errors when reading NAND
+*
+* PURPOSE:
+* This routine reads the BCH registers to determine if there are any bit
+* errors during the read of the last 512 bytes of data + ECC bytes. If
+* errors exists, the routine fixes it.
+*
+* PARAMETERS:
+* datap - Container that holds the 512 byte data
+*
+* RETURNS:
+* 0 or greater = Number of errors corrected
+* (No errors are found or errors have been fixed)
+* -1 = Error(s) cannot be fixed
+****************************************************************************/
+int nand_bcm_umi_bch_correct_page(uint8_t *datap, uint8_t *readEccData,
+ int numEccBytes)
+{
+ int numErrors;
+ int errorLocation;
+ int idx;
+ uint32_t regValue;
+
+ /* wait for read ECC to be valid */
+ regValue = nand_bcm_umi_bch_poll_read_ecc_calc();
+
+ /*
+ * read the control status register to determine if there
+ * are error'ed bits
+ * see if errors are correctible
+ */
+ if ((regValue & REG_UMI_BCH_CTRL_STATUS_UNCORR_ERR) > 0) {
+ int i;
+
+ for (i = 0; i < numEccBytes; i++) {
+ if (readEccData[i] != 0xff) {
+ /* errors cannot be fixed, return -1 */
+ return -1;
+ }
+ }
+ /* If ECC is unprogrammed then we can't correct,
+ * assume everything OK */
+ return 0;
+ }
+
+ if ((regValue & REG_UMI_BCH_CTRL_STATUS_CORR_ERR) == 0) {
+ /* no errors */
+ return 0;
+ }
+
+ /*
+ * Fix errored bits by doing the following:
+ * 1. Read the number of errors in the control and status register
+ * 2. Read the error location registers that corresponds to the number
+ * of errors reported
+ * 3. Invert the bit in the data
+ */
+ numErrors = (regValue & REG_UMI_BCH_CTRL_STATUS_NB_CORR_ERROR) >> 20;
+
+ for (idx = 0; idx < numErrors; idx++) {
+ errorLocation =
+ REG_UMI_BCH_ERR_LOC_ADDR(idx) & REG_UMI_BCH_ERR_LOC_MASK;
+
+ /* Flip bit */
+ nand_bcm_umi_bch_ecc_flip_bit(datap, errorLocation);
+ }
+ /* Errors corrected */
+ return numErrors;
+}
+#endif
diff --git a/drivers/mtd/nand/nand_bcm_umi.h b/drivers/mtd/nand/nand_bcm_umi.h
new file mode 100644
index 00000000000..7cec2cd9785
--- /dev/null
+++ b/drivers/mtd/nand/nand_bcm_umi.h
@@ -0,0 +1,358 @@
+/*****************************************************************************
+* Copyright 2003 - 2009 Broadcom Corporation. All rights reserved.
+*
+* Unless you and Broadcom execute a separate written software license
+* agreement governing use of this software, this software is licensed to you
+* under the terms of the GNU General Public License version 2, available at
+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
+*
+* Notwithstanding the above, under no circumstances may you combine this
+* software in any way with any other Broadcom software provided under a
+* license other than the GPL, without Broadcom's express prior written
+* consent.
+*****************************************************************************/
+#ifndef NAND_BCM_UMI_H
+#define NAND_BCM_UMI_H
+
+/* ---- Include Files ---------------------------------------------------- */
+#include <mach/reg_umi.h>
+#include <mach/reg_nand.h>
+#include <cfg_global.h>
+
+/* ---- Constants and Types ---------------------------------------------- */
+#if (CFG_GLOBAL_CHIP_FAMILY == CFG_GLOBAL_CHIP_FAMILY_BCMRING)
+#define NAND_ECC_BCH (CFG_GLOBAL_CHIP_REV > 0xA0)
+#else
+#define NAND_ECC_BCH 0
+#endif
+
+#define CFG_GLOBAL_NAND_ECC_BCH_NUM_BYTES 13
+
+#if NAND_ECC_BCH
+#ifdef BOOT0_BUILD
+#define NAND_ECC_NUM_BYTES 13
+#else
+#define NAND_ECC_NUM_BYTES CFG_GLOBAL_NAND_ECC_BCH_NUM_BYTES
+#endif
+#else
+#define NAND_ECC_NUM_BYTES 3
+#endif
+
+#define NAND_DATA_ACCESS_SIZE 512
+
+/* ---- Variable Externs ------------------------------------------ */
+/* ---- Function Prototypes --------------------------------------- */
+int nand_bcm_umi_bch_correct_page(uint8_t *datap, uint8_t *readEccData,
+ int numEccBytes);
+
+/* Check in device is ready */
+static inline int nand_bcm_umi_dev_ready(void)
+{
+ return REG_UMI_NAND_RCSR & REG_UMI_NAND_RCSR_RDY;
+}
+
+/* Wait until device is ready */
+static inline void nand_bcm_umi_wait_till_ready(void)
+{
+ while (nand_bcm_umi_dev_ready() == 0)
+ ;
+}
+
+/* Enable Hamming ECC */
+static inline void nand_bcm_umi_hamming_enable_hwecc(void)
+{
+ /* disable and reset ECC, 512 byte page */
+ REG_UMI_NAND_ECC_CSR &= ~(REG_UMI_NAND_ECC_CSR_ECC_ENABLE |
+ REG_UMI_NAND_ECC_CSR_256BYTE);
+ /* enable ECC */
+ REG_UMI_NAND_ECC_CSR |= REG_UMI_NAND_ECC_CSR_ECC_ENABLE;
+}
+
+#if NAND_ECC_BCH
+/* BCH ECC specifics */
+#define ECC_BITS_PER_CORRECTABLE_BIT 13
+
+/* Enable BCH Read ECC */
+static inline void nand_bcm_umi_bch_enable_read_hwecc(void)
+{
+ /* disable and reset ECC */
+ REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_RD_ECC_VALID;
+ /* Turn on ECC */
+ REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_ECC_RD_EN;
+}
+
+/* Enable BCH Write ECC */
+static inline void nand_bcm_umi_bch_enable_write_hwecc(void)
+{
+ /* disable and reset ECC */
+ REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_WR_ECC_VALID;
+ /* Turn on ECC */
+ REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_ECC_WR_EN;
+}
+
+/* Config number of BCH ECC bytes */
+static inline void nand_bcm_umi_bch_config_ecc(uint8_t numEccBytes)
+{
+ uint32_t nValue;
+ uint32_t tValue;
+ uint32_t kValue;
+ uint32_t numBits = numEccBytes * 8;
+
+ /* disable and reset ECC */
+ REG_UMI_BCH_CTRL_STATUS =
+ REG_UMI_BCH_CTRL_STATUS_WR_ECC_VALID |
+ REG_UMI_BCH_CTRL_STATUS_RD_ECC_VALID;
+
+ /* Every correctible bit requires 13 ECC bits */
+ tValue = (uint32_t) (numBits / ECC_BITS_PER_CORRECTABLE_BIT);
+
+ /* Total data in number of bits for generating and computing BCH ECC */
+ nValue = (NAND_DATA_ACCESS_SIZE + numEccBytes) * 8;
+
+ /* K parameter is used internally. K = N - (T * 13) */
+ kValue = nValue - (tValue * ECC_BITS_PER_CORRECTABLE_BIT);
+
+ /* Write the settings */
+ REG_UMI_BCH_N = nValue;
+ REG_UMI_BCH_T = tValue;
+ REG_UMI_BCH_K = kValue;
+}
+
+/* Pause during ECC read calculation to skip bytes in OOB */
+static inline void nand_bcm_umi_bch_pause_read_ecc_calc(void)
+{
+ REG_UMI_BCH_CTRL_STATUS =
+ REG_UMI_BCH_CTRL_STATUS_ECC_RD_EN |
+ REG_UMI_BCH_CTRL_STATUS_PAUSE_ECC_DEC;
+}
+
+/* Resume during ECC read calculation after skipping bytes in OOB */
+static inline void nand_bcm_umi_bch_resume_read_ecc_calc(void)
+{
+ REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_ECC_RD_EN;
+}
+
+/* Poll read ECC calc to check when hardware completes */
+static inline uint32_t nand_bcm_umi_bch_poll_read_ecc_calc(void)
+{
+ uint32_t regVal;
+
+ do {
+ /* wait for ECC to be valid */
+ regVal = REG_UMI_BCH_CTRL_STATUS;
+ } while ((regVal & REG_UMI_BCH_CTRL_STATUS_RD_ECC_VALID) == 0);
+
+ return regVal;
+}
+
+/* Poll write ECC calc to check when hardware completes */
+static inline void nand_bcm_umi_bch_poll_write_ecc_calc(void)
+{
+ /* wait for ECC to be valid */
+ while ((REG_UMI_BCH_CTRL_STATUS & REG_UMI_BCH_CTRL_STATUS_WR_ECC_VALID)
+ == 0)
+ ;
+}
+
+/* Read the OOB and ECC, for kernel write OOB to a buffer */
+#if defined(__KERNEL__) && !defined(STANDALONE)
+static inline void nand_bcm_umi_bch_read_oobEcc(uint32_t pageSize,
+ uint8_t *eccCalc, int numEccBytes, uint8_t *oobp)
+#else
+static inline void nand_bcm_umi_bch_read_oobEcc(uint32_t pageSize,
+ uint8_t *eccCalc, int numEccBytes)
+#endif
+{
+ int eccPos = 0;
+ int numToRead = 16; /* There are 16 bytes per sector in the OOB */
+
+ /* ECC is already paused when this function is called */
+
+ if (pageSize == NAND_DATA_ACCESS_SIZE) {
+ while (numToRead > numEccBytes) {
+ /* skip free oob region */
+#if defined(__KERNEL__) && !defined(STANDALONE)
+ *oobp++ = REG_NAND_DATA8;
+#else
+ REG_NAND_DATA8;
+#endif
+ numToRead--;
+ }
+
+ /* read ECC bytes before BI */
+ nand_bcm_umi_bch_resume_read_ecc_calc();
+
+ while (numToRead > 11) {
+#if defined(__KERNEL__) && !defined(STANDALONE)
+ *oobp = REG_NAND_DATA8;
+ eccCalc[eccPos++] = *oobp;
+ oobp++;
+#else
+ eccCalc[eccPos++] = REG_NAND_DATA8;
+#endif
+ }
+
+ nand_bcm_umi_bch_pause_read_ecc_calc();
+
+ if (numToRead == 11) {
+ /* read BI */
+#if defined(__KERNEL__) && !defined(STANDALONE)
+ *oobp++ = REG_NAND_DATA8;
+#else
+ REG_NAND_DATA8;
+#endif
+ numToRead--;
+ }
+
+ /* read ECC bytes */
+ nand_bcm_umi_bch_resume_read_ecc_calc();
+ while (numToRead) {
+#if defined(__KERNEL__) && !defined(STANDALONE)
+ *oobp = REG_NAND_DATA8;
+ eccCalc[eccPos++] = *oobp;
+ oobp++;
+#else
+ eccCalc[eccPos++] = REG_NAND_DATA8;
+#endif
+ numToRead--;
+ }
+ } else {
+ /* skip BI */
+#if defined(__KERNEL__) && !defined(STANDALONE)
+ *oobp++ = REG_NAND_DATA8;
+#else
+ REG_NAND_DATA8;
+#endif
+ numToRead--;
+
+ while (numToRead > numEccBytes) {
+ /* skip free oob region */
+#if defined(__KERNEL__) && !defined(STANDALONE)
+ *oobp++ = REG_NAND_DATA8;
+#else
+ REG_NAND_DATA8;
+#endif
+ numToRead--;
+ }
+
+ /* read ECC bytes */
+ nand_bcm_umi_bch_resume_read_ecc_calc();
+ while (numToRead) {
+#if defined(__KERNEL__) && !defined(STANDALONE)
+ *oobp = REG_NAND_DATA8;
+ eccCalc[eccPos++] = *oobp;
+ oobp++;
+#else
+ eccCalc[eccPos++] = REG_NAND_DATA8;
+#endif
+ numToRead--;
+ }
+ }
+}
+
+/* Helper function to write ECC */
+static inline void NAND_BCM_UMI_ECC_WRITE(int numEccBytes, int eccBytePos,
+ uint8_t *oobp, uint8_t eccVal)
+{
+ if (eccBytePos <= numEccBytes)
+ *oobp = eccVal;
+}
+
+/* Write OOB with ECC */
+static inline void nand_bcm_umi_bch_write_oobEcc(uint32_t pageSize,
+ uint8_t *oobp, int numEccBytes)
+{
+ uint32_t eccVal = 0xffffffff;
+
+ /* wait for write ECC to be valid */
+ nand_bcm_umi_bch_poll_write_ecc_calc();
+
+ /*
+ ** Get the hardware ecc from the 32-bit result registers.
+ ** Read after 512 byte accesses. Format B3B2B1B0
+ ** where B3 = ecc3, etc.
+ */
+
+ if (pageSize == NAND_DATA_ACCESS_SIZE) {
+ /* Now fill in the ECC bytes */
+ if (numEccBytes >= 13)
+ eccVal = REG_UMI_BCH_WR_ECC_3;
+
+ /* Usually we skip CM in oob[0,1] */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 15, &oobp[0],
+ (eccVal >> 16) & 0xff);
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 14, &oobp[1],
+ (eccVal >> 8) & 0xff);
+
+ /* Write ECC in oob[2,3,4] */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 13, &oobp[2],
+ eccVal & 0xff); /* ECC 12 */
+
+ if (numEccBytes >= 9)
+ eccVal = REG_UMI_BCH_WR_ECC_2;
+
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 12, &oobp[3],
+ (eccVal >> 24) & 0xff); /* ECC11 */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 11, &oobp[4],
+ (eccVal >> 16) & 0xff); /* ECC10 */
+
+ /* Always Skip BI in oob[5] */
+ } else {
+ /* Always Skip BI in oob[0] */
+
+ /* Now fill in the ECC bytes */
+ if (numEccBytes >= 13)
+ eccVal = REG_UMI_BCH_WR_ECC_3;
+
+ /* Usually skip CM in oob[1,2] */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 15, &oobp[1],
+ (eccVal >> 16) & 0xff);
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 14, &oobp[2],
+ (eccVal >> 8) & 0xff);
+
+ /* Write ECC in oob[3-15] */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 13, &oobp[3],
+ eccVal & 0xff); /* ECC12 */
+
+ if (numEccBytes >= 9)
+ eccVal = REG_UMI_BCH_WR_ECC_2;
+
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 12, &oobp[4],
+ (eccVal >> 24) & 0xff); /* ECC11 */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 11, &oobp[5],
+ (eccVal >> 16) & 0xff); /* ECC10 */
+ }
+
+ /* Fill in the remainder of ECC locations */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 10, &oobp[6],
+ (eccVal >> 8) & 0xff); /* ECC9 */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 9, &oobp[7],
+ eccVal & 0xff); /* ECC8 */
+
+ if (numEccBytes >= 5)
+ eccVal = REG_UMI_BCH_WR_ECC_1;
+
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 8, &oobp[8],
+ (eccVal >> 24) & 0xff); /* ECC7 */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 7, &oobp[9],
+ (eccVal >> 16) & 0xff); /* ECC6 */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 6, &oobp[10],
+ (eccVal >> 8) & 0xff); /* ECC5 */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 5, &oobp[11],
+ eccVal & 0xff); /* ECC4 */
+
+ if (numEccBytes >= 1)
+ eccVal = REG_UMI_BCH_WR_ECC_0;
+
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 4, &oobp[12],
+ (eccVal >> 24) & 0xff); /* ECC3 */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 3, &oobp[13],
+ (eccVal >> 16) & 0xff); /* ECC2 */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 2, &oobp[14],
+ (eccVal >> 8) & 0xff); /* ECC1 */
+ NAND_BCM_UMI_ECC_WRITE(numEccBytes, 1, &oobp[15],
+ eccVal & 0xff); /* ECC0 */
+}
+#endif
+
+#endif /* NAND_BCM_UMI_H */
diff --git a/drivers/mtd/nand/nand_ecc.c b/drivers/mtd/nand/nand_ecc.c
index 92320a64327..271b8e735e8 100644
--- a/drivers/mtd/nand/nand_ecc.c
+++ b/drivers/mtd/nand/nand_ecc.c
@@ -150,20 +150,19 @@ static const char addressbits[256] = {
};
/**
- * nand_calculate_ecc - [NAND Interface] Calculate 3-byte ECC for 256/512-byte
+ * __nand_calculate_ecc - [NAND Interface] Calculate 3-byte ECC for 256/512-byte
* block
- * @mtd: MTD block structure
* @buf: input buffer with raw data
+ * @eccsize: data bytes per ecc step (256 or 512)
* @code: output buffer with ECC
*/
-int nand_calculate_ecc(struct mtd_info *mtd, const unsigned char *buf,
+void __nand_calculate_ecc(const unsigned char *buf, unsigned int eccsize,
unsigned char *code)
{
int i;
const uint32_t *bp = (uint32_t *)buf;
/* 256 or 512 bytes/ecc */
- const uint32_t eccsize_mult =
- (((struct nand_chip *)mtd->priv)->ecc.size) >> 8;
+ const uint32_t eccsize_mult = eccsize >> 8;
uint32_t cur; /* current value in buffer */
/* rp0..rp15..rp17 are the various accumulated parities (per byte) */
uint32_t rp0, rp1, rp2, rp3, rp4, rp5, rp6, rp7;
@@ -412,6 +411,22 @@ int nand_calculate_ecc(struct mtd_info *mtd, const unsigned char *buf,
(invparity[par & 0x55] << 2) |
(invparity[rp17] << 1) |
(invparity[rp16] << 0);
+}
+EXPORT_SYMBOL(__nand_calculate_ecc);
+
+/**
+ * nand_calculate_ecc - [NAND Interface] Calculate 3-byte ECC for 256/512-byte
+ * block
+ * @mtd: MTD block structure
+ * @buf: input buffer with raw data
+ * @code: output buffer with ECC
+ */
+int nand_calculate_ecc(struct mtd_info *mtd, const unsigned char *buf,
+ unsigned char *code)
+{
+ __nand_calculate_ecc(buf,
+ ((struct nand_chip *)mtd->priv)->ecc.size, code);
+
return 0;
}
EXPORT_SYMBOL(nand_calculate_ecc);
diff --git a/drivers/mtd/nand/nandsim.c b/drivers/mtd/nand/nandsim.c
index cd0711b83ac..7281000fef2 100644
--- a/drivers/mtd/nand/nandsim.c
+++ b/drivers/mtd/nand/nandsim.c
@@ -161,7 +161,7 @@ MODULE_PARM_DESC(overridesize, "Specifies the NAND Flash size overriding the I
MODULE_PARM_DESC(cache_file, "File to use to cache nand pages instead of memory");
/* The largest possible page size */
-#define NS_LARGEST_PAGE_SIZE 2048
+#define NS_LARGEST_PAGE_SIZE 4096
/* The prefix for simulator output */
#define NS_OUTPUT_PREFIX "[nandsim]"
@@ -259,7 +259,8 @@ MODULE_PARM_DESC(cache_file, "File to use to cache nand pages instead of mem
#define OPT_SMARTMEDIA 0x00000010 /* SmartMedia technology chips */
#define OPT_AUTOINCR 0x00000020 /* page number auto inctimentation is possible */
#define OPT_PAGE512_8BIT 0x00000040 /* 512-byte page chips with 8-bit bus width */
-#define OPT_LARGEPAGE (OPT_PAGE2048) /* 2048-byte page chips */
+#define OPT_PAGE4096 0x00000080 /* 4096-byte page chips */
+#define OPT_LARGEPAGE (OPT_PAGE2048 | OPT_PAGE4096) /* 2048 & 4096-byte page chips */
#define OPT_SMALLPAGE (OPT_PAGE256 | OPT_PAGE512) /* 256 and 512-byte page chips */
/* Remove action bits ftom state */
@@ -588,6 +589,8 @@ static int init_nandsim(struct mtd_info *mtd)
ns->options |= OPT_PAGE512_8BIT;
} else if (ns->geom.pgsz == 2048) {
ns->options |= OPT_PAGE2048;
+ } else if (ns->geom.pgsz == 4096) {
+ ns->options |= OPT_PAGE4096;
} else {
NS_ERR("init_nandsim: unknown page size %u\n", ns->geom.pgsz);
return -EIO;
diff --git a/drivers/mtd/nand/nomadik_nand.c b/drivers/mtd/nand/nomadik_nand.c
index 7c302d55910..66123419f65 100644
--- a/drivers/mtd/nand/nomadik_nand.c
+++ b/drivers/mtd/nand/nomadik_nand.c
@@ -216,7 +216,7 @@ static int nomadik_nand_resume(struct device *dev)
return 0;
}
-static struct dev_pm_ops nomadik_nand_pm_ops = {
+static const struct dev_pm_ops nomadik_nand_pm_ops = {
.suspend = nomadik_nand_suspend,
.resume = nomadik_nand_resume,
};
diff --git a/drivers/mtd/nand/plat_nand.c b/drivers/mtd/nand/plat_nand.c
index 4e16c6f5bdd..8d467315f02 100644
--- a/drivers/mtd/nand/plat_nand.c
+++ b/drivers/mtd/nand/plat_nand.c
@@ -34,7 +34,12 @@ static int __devinit plat_nand_probe(struct platform_device *pdev)
{
struct platform_nand_data *pdata = pdev->dev.platform_data;
struct plat_nand_data *data;
- int res = 0;
+ struct resource *res;
+ int err = 0;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res)
+ return -ENXIO;
/* Allocate memory for the device structure (and zero it) */
data = kzalloc(sizeof(struct plat_nand_data), GFP_KERNEL);
@@ -43,12 +48,18 @@ static int __devinit plat_nand_probe(struct platform_device *pdev)
return -ENOMEM;
}
- data->io_base = ioremap(pdev->resource[0].start,
- pdev->resource[0].end - pdev->resource[0].start + 1);
+ if (!request_mem_region(res->start, resource_size(res),
+ dev_name(&pdev->dev))) {
+ dev_err(&pdev->dev, "request_mem_region failed\n");
+ err = -EBUSY;
+ goto out_free;
+ }
+
+ data->io_base = ioremap(res->start, resource_size(res));
if (data->io_base == NULL) {
dev_err(&pdev->dev, "ioremap failed\n");
- kfree(data);
- return -EIO;
+ err = -EIO;
+ goto out_release_io;
}
data->chip.priv = &data;
@@ -74,24 +85,24 @@ static int __devinit plat_nand_probe(struct platform_device *pdev)
/* Handle any platform specific setup */
if (pdata->ctrl.probe) {
- res = pdata->ctrl.probe(pdev);
- if (res)
+ err = pdata->ctrl.probe(pdev);
+ if (err)
goto out;
}
/* Scan to find existance of the device */
if (nand_scan(&data->mtd, 1)) {
- res = -ENXIO;
+ err = -ENXIO;
goto out;
}
#ifdef CONFIG_MTD_PARTITIONS
if (pdata->chip.part_probe_types) {
- res = parse_mtd_partitions(&data->mtd,
+ err = parse_mtd_partitions(&data->mtd,
pdata->chip.part_probe_types,
&data->parts, 0);
- if (res > 0) {
- add_mtd_partitions(&data->mtd, data->parts, res);
+ if (err > 0) {
+ add_mtd_partitions(&data->mtd, data->parts, err);
return 0;
}
}
@@ -99,14 +110,14 @@ static int __devinit plat_nand_probe(struct platform_device *pdev)
pdata->chip.set_parts(data->mtd.size, &pdata->chip);
if (pdata->chip.partitions) {
data->parts = pdata->chip.partitions;
- res = add_mtd_partitions(&data->mtd, data->parts,
+ err = add_mtd_partitions(&data->mtd, data->parts,
pdata->chip.nr_partitions);
} else
#endif
- res = add_mtd_device(&data->mtd);
+ err = add_mtd_device(&data->mtd);
- if (!res)
- return res;
+ if (!err)
+ return err;
nand_release(&data->mtd);
out:
@@ -114,8 +125,11 @@ out:
pdata->ctrl.remove(pdev);
platform_set_drvdata(pdev, NULL);
iounmap(data->io_base);
+out_release_io:
+ release_mem_region(res->start, resource_size(res));
+out_free:
kfree(data);
- return res;
+ return err;
}
/*
@@ -125,6 +139,9 @@ static int __devexit plat_nand_remove(struct platform_device *pdev)
{
struct plat_nand_data *data = platform_get_drvdata(pdev);
struct platform_nand_data *pdata = pdev->dev.platform_data;
+ struct resource *res;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
nand_release(&data->mtd);
#ifdef CONFIG_MTD_PARTITIONS
@@ -134,6 +151,7 @@ static int __devexit plat_nand_remove(struct platform_device *pdev)
if (pdata->ctrl.remove)
pdata->ctrl.remove(pdev);
iounmap(data->io_base);
+ release_mem_region(res->start, resource_size(res));
kfree(data);
return 0;
diff --git a/drivers/mtd/nand/s3c2410.c b/drivers/mtd/nand/s3c2410.c
index 68b5b3a486a..fa6e9c7fe51 100644
--- a/drivers/mtd/nand/s3c2410.c
+++ b/drivers/mtd/nand/s3c2410.c
@@ -774,7 +774,7 @@ static void s3c2410_nand_init_chip(struct s3c2410_nand_info *info,
chip->select_chip = s3c2410_nand_select_chip;
chip->chip_delay = 50;
chip->priv = nmtd;
- chip->options = 0;
+ chip->options = set->options;
chip->controller = &info->controller;
switch (info->cpu_type) {
diff --git a/drivers/mtd/nand/txx9ndfmc.c b/drivers/mtd/nand/txx9ndfmc.c
index 73af8324d0d..863513c3b69 100644
--- a/drivers/mtd/nand/txx9ndfmc.c
+++ b/drivers/mtd/nand/txx9ndfmc.c
@@ -429,11 +429,10 @@ static int __exit txx9ndfmc_remove(struct platform_device *dev)
chip = mtd->priv;
txx9_priv = chip->priv;
+ nand_release(mtd);
#ifdef CONFIG_MTD_PARTITIONS
- del_mtd_partitions(mtd);
kfree(drvdata->parts[i]);
#endif
- del_mtd_device(mtd);
kfree(txx9_priv->mtdname);
kfree(txx9_priv);
}
generated by cgit v1.2.3 (git 2.39.1) at 2024-06-01 23:53:18 +0000