diff options
51 files changed, 1534 insertions, 120 deletions
diff --git a/Documentation/hwmon/adt7473 b/Documentation/hwmon/adt7473 new file mode 100644 index 00000000000..22d8b19046a --- /dev/null +++ b/Documentation/hwmon/adt7473 @@ -0,0 +1,79 @@ +Kernel driver adt7473 +====================== + +Supported chips: + * Analog Devices ADT7473 + Prefix: 'adt7473' + Addresses scanned: I2C 0x2C, 0x2D, 0x2E + Datasheet: Publicly available at the Analog Devices website + +Author: Darrick J. Wong + +Description +----------- + +This driver implements support for the Analog Devices ADT7473 chip family. + +The LM85 uses the 2-wire interface compatible with the SMBUS 2.0 +specification. Using an analog to digital converter it measures three (3) +temperatures and two (2) voltages. It has three (3) 16-bit counters for +measuring fan speed. There are three (3) PWM outputs that can be used +to control fan speed. + +A sophisticated control system for the PWM outputs is designed into the +LM85 that allows fan speed to be adjusted automatically based on any of the +three temperature sensors. Each PWM output is individually adjustable and +programmable. Once configured, the ADT7473 will adjust the PWM outputs in +response to the measured temperatures without further host intervention. +This feature can also be disabled for manual control of the PWM's. + +Each of the measured inputs (voltage, temperature, fan speed) has +corresponding high/low limit values. The ADT7473 will signal an ALARM if +any measured value exceeds either limit. + +The ADT7473 samples all inputs continuously. The driver will not read +the registers more often than once every other second. Further, +configuration data is only read once per minute. + +Special Features +---------------- + +The ADT7473 have a 10-bit ADC and can therefore measure temperatures +with 0.25 degC resolution. Temperature readings can be configured either +for twos complement format or "Offset 64" format, wherein 63 is subtracted +from the raw value to get the temperature value. + +The Analog Devices datasheet is very detailed and describes a procedure for +determining an optimal configuration for the automatic PWM control. + +Hardware Configurations +----------------------- + +The ADT7473 chips have an optional SMBALERT output that can be used to +signal the chipset in case a limit is exceeded or the temperature sensors +fail. Individual sensor interrupts can be masked so they won't trigger +SMBALERT. The SMBALERT output if configured replaces the PWM2 function. + +Configuration Notes +------------------- + +Besides standard interfaces driver adds the following: + +* PWM Control + +* pwm#_auto_point1_pwm and pwm#_auto_point1_temp and +* pwm#_auto_point2_pwm and pwm#_auto_point2_temp - + +point1: Set the pwm speed at a lower temperature bound. +point2: Set the pwm speed at a higher temperature bound. + +The ADT7473 will scale the pwm between the lower and higher pwm speed when +the temperature is between the two temperature boundaries. PWM values range +from 0 (off) to 255 (full speed). + +Notes +----- + +The NVIDIA binary driver presents an ADT7473 chip via an on-card i2c bus. +Unfortunately, they fail to set the i2c adapter class, so this driver may +fail to find the chip until the nvidia driver is patched. diff --git a/Documentation/hwmon/coretemp b/Documentation/hwmon/coretemp index 170bf862437..dbbe6c7025b 100644 --- a/Documentation/hwmon/coretemp +++ b/Documentation/hwmon/coretemp @@ -4,9 +4,10 @@ Kernel driver coretemp Supported chips: * All Intel Core family Prefix: 'coretemp' - CPUID: family 0x6, models 0xe, 0xf, 0x16 + CPUID: family 0x6, models 0xe, 0xf, 0x16, 0x17 Datasheet: Intel 64 and IA-32 Architectures Software Developer's Manual Volume 3A: System Programming Guide + http://softwarecommunity.intel.com/Wiki/Mobility/720.htm Author: Rudolf Marek @@ -25,7 +26,8 @@ may be raised, if the temperature grows enough (more than TjMax) to trigger the Out-Of-Spec bit. Following table summarizes the exported sysfs files: temp1_input - Core temperature (in millidegrees Celsius). -temp1_crit - Maximum junction temperature (in millidegrees Celsius). +temp1_max - All cooling devices should be turned on (on Core2). +temp1_crit - Maximum junction temperature (in millidegrees Celsius). temp1_crit_alarm - Set when Out-of-spec bit is set, never clears. Correct CPU operation is no longer guaranteed. temp1_label - Contains string "Core X", where X is processor diff --git a/MAINTAINERS b/MAINTAINERS index fd81e0672c0..962babe226c 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -4261,7 +4261,7 @@ S: Maintained VT8231 HARDWARE MONITOR DRIVER P: Roger Lucas -M: roger@planbit.co.uk +M: vt8231@hiddenengine.co.uk L: lm-sensors@lm-sensors.org S: Maintained diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 410ffe4e9d8..368879ff5d8 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -143,6 +143,16 @@ config SENSORS_ADT7470 This driver can also be built as a module. If so, the module will be called adt7470. +config SENSORS_ADT7473 + tristate "Analog Devices ADT7473" + depends on I2C && EXPERIMENTAL + help + If you say yes here you get support for the Analog Devices + ADT7473 temperature monitoring chips. + + This driver can also be built as a module. If so, the module + will be called adt7473. + config SENSORS_K8TEMP tristate "AMD Athlon64/FX or Opteron temperature sensor" depends on X86 && PCI && EXPERIMENTAL diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 824161337f1..3bdb05a5cbd 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -24,6 +24,7 @@ obj-$(CONFIG_SENSORS_ADM1031) += adm1031.o obj-$(CONFIG_SENSORS_ADM9240) += adm9240.o obj-$(CONFIG_SENSORS_ADS7828) += ads7828.o obj-$(CONFIG_SENSORS_ADT7470) += adt7470.o +obj-$(CONFIG_SENSORS_ADT7473) += adt7473.o obj-$(CONFIG_SENSORS_APPLESMC) += applesmc.o obj-$(CONFIG_SENSORS_AMS) += ams/ obj-$(CONFIG_SENSORS_ATXP1) += atxp1.o diff --git a/drivers/hwmon/ad7418.c b/drivers/hwmon/ad7418.c index fcd7fe78f3f..466b9ee9279 100644 --- a/drivers/hwmon/ad7418.c +++ b/drivers/hwmon/ad7418.c @@ -26,7 +26,7 @@ #define DRV_VERSION "0.3" /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x28, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x28, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_3(ad7416, ad7417, ad7418); diff --git a/drivers/hwmon/adm1021.c b/drivers/hwmon/adm1021.c index b96be772e49..ecbf69484bf 100644 --- a/drivers/hwmon/adm1021.c +++ b/drivers/hwmon/adm1021.c @@ -31,10 +31,8 @@ /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x18, 0x19, 0x1a, - 0x29, 0x2a, 0x2b, - 0x4c, 0x4d, 0x4e, - I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { + 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, 0x4d, 0x4e, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_8(adm1021, adm1023, max1617, max1617a, thmc10, lm84, gl523sm, diff --git a/drivers/hwmon/adm1025.c b/drivers/hwmon/adm1025.c index e96c3725203..1d76de7d75c 100644 --- a/drivers/hwmon/adm1025.c +++ b/drivers/hwmon/adm1025.c @@ -62,7 +62,7 @@ * NE1619 has two possible addresses: 0x2c and 0x2d. */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; /* * Insmod parameters diff --git a/drivers/hwmon/adm1026.c b/drivers/hwmon/adm1026.c index 8002f68240c..904c6ce9d83 100644 --- a/drivers/hwmon/adm1026.c +++ b/drivers/hwmon/adm1026.c @@ -35,7 +35,7 @@ #include <linux/mutex.h> /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(adm1026); @@ -1624,6 +1624,7 @@ static struct attribute *adm1026_attributes_temp3[] = { &dev_attr_temp3_crit_enable.attr, &dev_attr_temp3_auto_point1_pwm.attr, &dev_attr_temp3_auto_point2_pwm.attr, + NULL }; static const struct attribute_group adm1026_group_temp3 = { @@ -1639,6 +1640,7 @@ static struct attribute *adm1026_attributes_in8_9[] = { &sensor_dev_attr_in9_max.dev_attr.attr, &sensor_dev_attr_in9_min.dev_attr.attr, &sensor_dev_attr_in9_alarm.dev_attr.attr, + NULL }; static const struct attribute_group adm1026_group_in8_9 = { diff --git a/drivers/hwmon/adm1029.c b/drivers/hwmon/adm1029.c index 0bc897dffa2..2c6608d453c 100644 --- a/drivers/hwmon/adm1029.c +++ b/drivers/hwmon/adm1029.c @@ -39,10 +39,8 @@ * Addresses to scan */ -static unsigned short normal_i2c[] = { - 0x28, 0x29, 0x2a, - 0x2b, 0x2c, 0x2d, - 0x2e, 0x2f, I2C_CLIENT_END +static const unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d, + 0x2e, 0x2f, I2C_CLIENT_END }; /* diff --git a/drivers/hwmon/adm1031.c b/drivers/hwmon/adm1031.c index 5aaad3636c9..2bffcab7dc9 100644 --- a/drivers/hwmon/adm1031.c +++ b/drivers/hwmon/adm1031.c @@ -61,7 +61,7 @@ #define ADM1031_CONF2_TEMP_ENABLE(chan) (0x10 << (chan)) /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_2(adm1030, adm1031); diff --git a/drivers/hwmon/adm9240.c b/drivers/hwmon/adm9240.c index 7671d2bf780..149ef25252e 100644 --- a/drivers/hwmon/adm9240.c +++ b/drivers/hwmon/adm9240.c @@ -52,7 +52,7 @@ #include <linux/mutex.h> /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END }; /* Insmod parameters */ diff --git a/drivers/hwmon/ads7828.c b/drivers/hwmon/ads7828.c index 6b8a73ef404..ed71a8bc70d 100644 --- a/drivers/hwmon/ads7828.c +++ b/drivers/hwmon/ads7828.c @@ -44,7 +44,7 @@ #define ADS7828_INT_VREF_MV 2500 /* Internal vref is 2.5V, 2500mV */ /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, +static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, I2C_CLIENT_END }; /* Insmod parameters */ diff --git a/drivers/hwmon/adt7470.c b/drivers/hwmon/adt7470.c index 747693ab2ff..6b5325f33a2 100644 --- a/drivers/hwmon/adt7470.c +++ b/drivers/hwmon/adt7470.c @@ -30,7 +30,7 @@ #include <linux/log2.h> /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2C, 0x2E, 0x2F, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2C, 0x2E, 0x2F, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(adt7470); diff --git a/drivers/hwmon/adt7473.c b/drivers/hwmon/adt7473.c new file mode 100644 index 00000000000..9587869bdba --- /dev/null +++ b/drivers/hwmon/adt7473.c @@ -0,0 +1,1157 @@ +/* + * A hwmon driver for the Analog Devices ADT7473 + * Copyright (C) 2007 IBM + * + * Author: Darrick J. Wong <djwong@us.ibm.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/module.h> +#include <linux/jiffies.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/err.h> +#include <linux/mutex.h> +#include <linux/delay.h> +#include <linux/log2.h> + +/* Addresses to scan */ +static const unsigned short normal_i2c[] = { 0x2C, 0x2D, 0x2E, I2C_CLIENT_END }; + +/* Insmod parameters */ +I2C_CLIENT_INSMOD_1(adt7473); + +/* ADT7473 registers */ +#define ADT7473_REG_BASE_ADDR 0x20 + +#define ADT7473_REG_VOLT_BASE_ADDR 0x21 +#define ADT7473_REG_VOLT_MAX_ADDR 0x22 +#define ADT7473_REG_VOLT_MIN_BASE_ADDR 0x46 +#define ADT7473_REG_VOLT_MIN_MAX_ADDR 0x49 + +#define ADT7473_REG_TEMP_BASE_ADDR 0x25 +#define ADT7473_REG_TEMP_MAX_ADDR 0x27 +#define ADT7473_REG_TEMP_LIMITS_BASE_ADDR 0x4E +#define ADT7473_REG_TEMP_LIMITS_MAX_ADDR 0x53 +#define ADT7473_REG_TEMP_TMIN_BASE_ADDR 0x67 +#define ADT7473_REG_TEMP_TMIN_MAX_ADDR 0x69 +#define ADT7473_REG_TEMP_TMAX_BASE_ADDR 0x6A +#define ADT7473_REG_TEMP_TMAX_MAX_ADDR 0x6C + +#define ADT7473_REG_FAN_BASE_ADDR 0x28 +#define ADT7473_REG_FAN_MAX_ADDR 0x2F +#define ADT7473_REG_FAN_MIN_BASE_ADDR 0x54 +#define ADT7473_REG_FAN_MIN_MAX_ADDR 0x5B + +#define ADT7473_REG_PWM_BASE_ADDR 0x30 +#define ADT7473_REG_PWM_MAX_ADDR 0x32 +#define ADT7473_REG_PWM_MIN_BASE_ADDR 0x64 +#define ADT7473_REG_PWM_MIN_MAX_ADDR 0x66 +#define ADT7473_REG_PWM_MAX_BASE_ADDR 0x38 +#define ADT7473_REG_PWM_MAX_MAX_ADDR 0x3A +#define ADT7473_REG_PWM_BHVR_BASE_ADDR 0x5C +#define ADT7473_REG_PWM_BHVR_MAX_ADDR 0x5E +#define ADT7473_PWM_BHVR_MASK 0xE0 +#define ADT7473_PWM_BHVR_SHIFT 5 + +#define ADT7473_REG_CFG1 0x40 +#define ADT7473_CFG1_START 0x01 +#define ADT7473_CFG1_READY 0x04 +#define ADT7473_REG_CFG2 0x73 +#define ADT7473_REG_CFG3 0x78 +#define ADT7473_REG_CFG4 0x7D +#define ADT7473_CFG4_MAX_DUTY_AT_OVT 0x08 +#define ADT7473_REG_CFG5 0x7C +#define ADT7473_CFG5_TEMP_TWOS 0x01 +#define ADT7473_CFG5_TEMP_OFFSET 0x02 + +#define ADT7473_REG_DEVICE 0x3D +#define ADT7473_VENDOR 0x41 +#define ADT7473_REG_VENDOR 0x3E +#define ADT7473_DEVICE 0x73 +#define ADT7473_REG_REVISION 0x3F +#define ADT7473_REV_68 0x68 +#define ADT7473_REV_69 0x69 + +#define ADT7473_REG_ALARM1 0x41 +#define ADT7473_VCCP_ALARM 0x02 +#define ADT7473_VCC_ALARM 0x04 +#define ADT7473_R1T_ALARM 0x10 +#define ADT7473_LT_ALARM 0x20 +#define ADT7473_R2T_ALARM 0x40 +#define ADT7473_OOL 0x80 +#define ADT7473_REG_ALARM2 0x42 +#define ADT7473_OVT_ALARM 0x02 +#define ADT7473_FAN1_ALARM 0x04 +#define ADT7473_FAN2_ALARM 0x08 +#define ADT7473_FAN3_ALARM 0x10 +#define ADT7473_FAN4_ALARM 0x20 +#define ADT7473_R1T_SHORT 0x40 +#define ADT7473_R2T_SHORT 0x80 +#define ADT7473_REG_MAX_ADDR 0x80 + +#define ALARM2(x) ((x) << 8) + +#define ADT7473_VOLT_COUNT 2 +#define ADT7473_REG_VOLT(x) (ADT7473_REG_VOLT_BASE_ADDR + (x)) +#define ADT7473_REG_VOLT_MIN(x) (ADT7473_REG_VOLT_MIN_BASE_ADDR + ((x) * 2)) +#define ADT7473_REG_VOLT_MAX(x) (ADT7473_REG_VOLT_MIN_BASE_ADDR + \ + ((x) * 2) + 1) + +#define ADT7473_TEMP_COUNT 3 +#define ADT7473_REG_TEMP(x) (ADT7473_REG_TEMP_BASE_ADDR + (x)) +#define ADT7473_REG_TEMP_MIN(x) (ADT7473_REG_TEMP_LIMITS_BASE_ADDR + ((x) * 2)) +#define ADT7473_REG_TEMP_MAX(x) (ADT7473_REG_TEMP_LIMITS_BASE_ADDR + \ + ((x) * 2) + 1) +#define ADT7473_REG_TEMP_TMIN(x) (ADT7473_REG_TEMP_TMIN_BASE_ADDR + (x)) +#define ADT7473_REG_TEMP_TMAX(x) (ADT7473_REG_TEMP_TMAX_BASE_ADDR + (x)) + +#define ADT7473_FAN_COUNT 4 +#define ADT7473_REG_FAN(x) (ADT7473_REG_FAN_BASE_ADDR + ((x) * 2)) +#define ADT7473_REG_FAN_MIN(x) (ADT7473_REG_FAN_MIN_BASE_ADDR + ((x) * 2)) + +#define ADT7473_PWM_COUNT 3 +#define ADT7473_REG_PWM(x) (ADT7473_REG_PWM_BASE_ADDR + (x)) +#define ADT7473_REG_PWM_MAX(x) (ADT7473_REG_PWM_MAX_BASE_ADDR + (x)) +#define ADT7473_REG_PWM_MIN(x) (ADT7473_REG_PWM_MIN_BASE_ADDR + (x)) +#define ADT7473_REG_PWM_BHVR(x) (ADT7473_REG_PWM_BHVR_BASE_ADDR + (x)) + +/* How often do we reread sensors values? (In jiffies) */ +#define SENSOR_REFRESH_INTERVAL (2 * HZ) + +/* How often do we reread sensor limit values? (In jiffies) */ +#define LIMIT_REFRESH_INTERVAL (60 * HZ) + +/* datasheet says to divide this number by the fan reading to get fan rpm */ +#define FAN_PERIOD_TO_RPM(x) ((90000 * 60) / (x)) +#define FAN_RPM_TO_PERIOD FAN_PERIOD_TO_RPM +#define FAN_PERIOD_INVALID 65535 +#define FAN_DATA_VALID(x) ((x) && (x) != FAN_PERIOD_INVALID) + +struct adt7473_data { + struct i2c_client client; + struct device *hwmon_dev; + struct attribute_group attrs; + struct mutex lock; + char sensors_valid; + char limits_valid; + unsigned long sensors_last_updated; /* In jiffies */ + unsigned long limits_last_updated; /* In jiffies */ + + u8 volt[ADT7473_VOLT_COUNT]; + s8 volt_min[ADT7473_VOLT_COUNT]; + s8 volt_max[ADT7473_VOLT_COUNT]; + + s8 temp[ADT7473_TEMP_COUNT]; + s8 temp_min[ADT7473_TEMP_COUNT]; + s8 temp_max[ADT7473_TEMP_COUNT]; + s8 temp_tmin[ADT7473_TEMP_COUNT]; + /* This is called the !THERM limit in the datasheet */ + s8 temp_tmax[ADT7473_TEMP_COUNT]; + + u16 fan[ADT7473_FAN_COUNT]; + u16 fan_min[ADT7473_FAN_COUNT]; + + u8 pwm[ADT7473_PWM_COUNT]; + u8 pwm_max[ADT7473_PWM_COUNT]; + u8 pwm_min[ADT7473_PWM_COUNT]; + u8 pwm_behavior[ADT7473_PWM_COUNT]; + + u8 temp_twos_complement; + u8 temp_offset; + + u16 alarm; + u8 max_duty_at_overheat; +}; + +static int adt7473_attach_adapter(struct i2c_adapter *adapter); +static int adt7473_detect(struct i2c_adapter *adapter, int address, int kind); +static int adt7473_detach_client(struct i2c_client *client); + +static struct i2c_driver adt7473_driver = { + .driver = { + .name = "adt7473", + }, + .attach_adapter = adt7473_attach_adapter, + .detach_client = adt7473_detach_client, +}; + +/* + * 16-bit registers on the ADT7473 are low-byte first. The data sheet says + * that the low byte must be read before the high byte. + */ +static inline int adt7473_read_word_data(struct i2c_client *client, u8 reg) +{ + u16 foo; + foo = i2c_smbus_read_byte_data(client, reg); + foo |= ((u16)i2c_smbus_read_byte_data(client, reg + 1) << 8); + return foo; +} + +static inline int adt7473_write_word_data(struct i2c_client *client, u8 reg, + u16 value) +{ + return i2c_smbus_write_byte_data(client, reg, value & 0xFF) + && i2c_smbus_write_byte_data(client, reg + 1, value >> 8); +} + +static void adt7473_init_client(struct i2c_client *client) +{ + int reg = i2c_smbus_read_byte_data(client, ADT7473_REG_CFG1); + + if (!(reg & ADT7473_CFG1_READY)) { + dev_err(&client->dev, "Chip not ready.\n"); + } else { + /* start monitoring */ + i2c_smbus_write_byte_data(client, ADT7473_REG_CFG1, + reg | ADT7473_CFG1_START); + } +} + +static struct adt7473_data *adt7473_update_device(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + unsigned long local_jiffies = jiffies; + u8 cfg; + int i; + + mutex_lock(&data->lock); + if (time_before(local_jiffies, data->sensors_last_updated + + SENSOR_REFRESH_INTERVAL) + && data->sensors_valid) + goto no_sensor_update; + + for (i = 0; i < ADT7473_VOLT_COUNT; i++) + data->volt[i] = i2c_smbus_read_byte_data(client, + ADT7473_REG_VOLT(i)); + + /* Determine temperature encoding */ + cfg = i2c_smbus_read_byte_data(client, ADT7473_REG_CFG5); + data->temp_twos_complement = (cfg & ADT7473_CFG5_TEMP_TWOS); + + /* + * What does this do? it implies a variable temperature sensor + * offset, but the datasheet doesn't say anything about this bit + * and other parts of the datasheet imply that "offset64" mode + * means that you shift temp values by -64 if the above bit was set. + */ + data->temp_offset = (cfg & ADT7473_CFG5_TEMP_OFFSET); + + for (i = 0; i < ADT7473_TEMP_COUNT; i++) + data->temp[i] = i2c_smbus_read_byte_data(client, + ADT7473_REG_TEMP(i)); + + for (i = 0; i < ADT7473_FAN_COUNT; i++) + data->fan[i] = adt7473_read_word_data(client, + ADT7473_REG_FAN(i)); + + for (i = 0; i < ADT7473_PWM_COUNT; i++) + data->pwm[i] = i2c_smbus_read_byte_data(client, + ADT7473_REG_PWM(i)); + + data->alarm = i2c_smbus_read_byte_data(client, ADT7473_REG_ALARM1); + if (data->alarm & ADT7473_OOL) + data->alarm |= ALARM2(i2c_smbus_read_byte_data(client, + ADT7473_REG_ALARM2)); + + data->sensors_last_updated = local_jiffies; + data->sensors_valid = 1; + +no_sensor_update: + if (time_before(local_jiffies, data->limits_last_updated + + LIMIT_REFRESH_INTERVAL) + && data->limits_valid) + goto out; + + for (i = 0; i < ADT7473_VOLT_COUNT; i++) { + data->volt_min[i] = i2c_smbus_read_byte_data(client, + ADT7473_REG_VOLT_MIN(i)); + data->volt_max[i] = i2c_smbus_read_byte_data(client, + ADT7473_REG_VOLT_MAX(i)); + } + + for (i = 0; i < ADT7473_TEMP_COUNT; i++) { + data->temp_min[i] = i2c_smbus_read_byte_data(client, + ADT7473_REG_TEMP_MIN(i)); + data->temp_max[i] = i2c_smbus_read_byte_data(client, + ADT7473_REG_TEMP_MAX(i)); + data->temp_tmin[i] = i2c_smbus_read_byte_data(client, + ADT7473_REG_TEMP_TMIN(i)); + data->temp_tmax[i] = i2c_smbus_read_byte_data(client, + ADT7473_REG_TEMP_TMAX(i)); + } + + for (i = 0; i < ADT7473_FAN_COUNT; i++) + data->fan_min[i] = adt7473_read_word_data(client, + ADT7473_REG_FAN_MIN(i)); + + for (i = 0; i < ADT7473_PWM_COUNT; i++) { + data->pwm_max[i] = i2c_smbus_read_byte_data(client, + ADT7473_REG_PWM_MAX(i)); + data->pwm_min[i] = i2c_smbus_read_byte_data(client, + ADT7473_REG_PWM_MIN(i)); + data->pwm_behavior[i] = i2c_smbus_read_byte_data(client, + ADT7473_REG_PWM_BHVR(i)); + } + + data->limits_last_updated = local_jiffies; + data->limits_valid = 1; + +out: + mutex_unlock(&data->lock); + return data; +} + +/* + * On this chip, voltages are given as a count of steps between a minimum + * and maximum voltage, not a direct voltage. + */ +static const int volt_convert_table[][2] = { + {2997, 3}, + {4395, 4}, +}; + +static int decode_volt(int volt_index, u8 raw) +{ + int cmax = volt_convert_table[volt_index][0]; + int cmin = volt_convert_table[volt_index][1]; + return ((raw * (cmax - cmin)) / 255) + cmin; +} + +static u8 encode_volt(int volt_index, int cooked) +{ + int cmax = volt_convert_table[volt_index][0]; + int cmin = volt_convert_table[volt_index][1]; + u8 x; + + if (cooked > cmax) + cooked = cmax; + else if (cooked < cmin) + cooked = cmin; + + x = ((cooked - cmin) * 255) / (cmax - cmin); + + return x; +} + +static ssize_t show_volt_min(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + return sprintf(buf, "%d\n", + decode_volt(attr->index, data->volt_min[attr->index])); +} + +static ssize_t set_volt_min(struct device *dev, + struct device_attribute *devattr, + const char *buf, + size_t count) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + int volt = encode_volt(attr->index, simple_strtol(buf, NULL, 10)); + + mutex_lock(&data->lock); + data->volt_min[attr->index] = volt; + i2c_smbus_write_byte_data(client, ADT7473_REG_VOLT_MIN(attr->index), + volt); + mutex_unlock(&data->lock); + + return count; +} + +static ssize_t show_volt_max(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + return sprintf(buf, "%d\n", + decode_volt(attr->index, data->volt_max[attr->index])); +} + +static ssize_t set_volt_max(struct device *dev, + struct device_attribute *devattr, + const char *buf, + size_t count) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + int volt = encode_volt(attr->index, simple_strtol(buf, NULL, 10)); + + mutex_lock(&data->lock); + data->volt_max[attr->index] = volt; + i2c_smbus_write_byte_data(client, ADT7473_REG_VOLT_MAX(attr->index), + volt); + mutex_unlock(&data->lock); + + return count; +} + +static ssize_t show_volt(struct device *dev, struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + + return sprintf(buf, "%d\n", + decode_volt(attr->index, data->volt[attr->index])); +} + +/* + * This chip can report temperature data either as a two's complement + * number in the range -128 to 127, or as an unsigned number that must + * be offset by 64. + */ +static int decode_temp(struct adt7473_data *data, u8 raw) +{ + if (data->temp_twos_complement) + return (s8)raw; + return raw - 64; +} + +static u8 encode_temp(struct adt7473_data *data, int cooked) +{ + if (data->temp_twos_complement) + return (cooked & 0xFF); + return cooked + 64; +} + +static ssize_t show_temp_min(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + return sprintf(buf, "%d\n", + 1000 * decode_temp(data, data->temp_min[attr->index])); +} + +static ssize_t set_temp_min(struct device *dev, + struct device_attribute *devattr, + const char *buf, + size_t count) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + int temp = simple_strtol(buf, NULL, 10) / 1000; + temp = encode_temp(data, temp); + + mutex_lock(&data->lock); + data->temp_min[attr->index] = temp; + i2c_smbus_write_byte_data(client, ADT7473_REG_TEMP_MIN(attr->index), + temp); + mutex_unlock(&data->lock); + + return count; +} + +static ssize_t show_temp_max(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + return sprintf(buf, "%d\n", + 1000 * decode_temp(data, data->temp_max[attr->index])); +} + +static ssize_t set_temp_max(struct device *dev, + struct device_attribute *devattr, + const char *buf, + size_t count) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + int temp = simple_strtol(buf, NULL, 10) / 1000; + temp = encode_temp(data, temp); + + mutex_lock(&data->lock); + data->temp_max[attr->index] = temp; + i2c_smbus_write_byte_data(client, ADT7473_REG_TEMP_MAX(attr->index), + temp); + mutex_unlock(&data->lock); + + return count; +} + +static ssize_t show_temp(struct device *dev, struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + return sprintf(buf, "%d\n", + 1000 * decode_temp(data, data->temp[attr->index])); +} + +static ssize_t show_fan_min(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + + if (FAN_DATA_VALID(data->fan_min[attr->index])) + return sprintf(buf, "%d\n", + FAN_PERIOD_TO_RPM(data->fan_min[attr->index])); + else + return sprintf(buf, "0\n"); +} + +static ssize_t set_fan_min(struct device *dev, + struct device_attribute *devattr, + const char *buf, size_t count) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + int temp = simple_strtol(buf, NULL, 10); + + if (!temp) + return -EINVAL; + temp = FAN_RPM_TO_PERIOD(temp); + + mutex_lock(&data->lock); + data->fan_min[attr->index] = temp; + adt7473_write_word_data(client, ADT7473_REG_FAN_MIN(attr->index), temp); + mutex_unlock(&data->lock); + + return count; +} + +static ssize_t show_fan(struct device *dev, struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + + if (FAN_DATA_VALID(data->fan[attr->index])) + return sprintf(buf, "%d\n", + FAN_PERIOD_TO_RPM(data->fan[attr->index])); + else + return sprintf(buf, "0\n"); +} + +static ssize_t show_max_duty_at_crit(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct adt7473_data *data = adt7473_update_device(dev); + return sprintf(buf, "%d\n", data->max_duty_at_overheat); +} + +static ssize_t set_max_duty_at_crit(struct device *dev, + struct device_attribute *devattr, + const char *buf, + size_t count) +{ + u8 reg; + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + int temp = simple_strtol(buf, NULL, 10); + temp = temp && 0xFF; + + mutex_lock(&data->lock); + data->max_duty_at_overheat = temp; + reg = i2c_smbus_read_byte_data(client, ADT7473_REG_CFG4); + if (temp) + reg |= ADT7473_CFG4_MAX_DUTY_AT_OVT; + else + reg &= ~ADT7473_CFG4_MAX_DUTY_AT_OVT; + i2c_smbus_write_byte_data(client, ADT7473_REG_CFG4, reg); + mutex_unlock(&data->lock); + + return count; +} + +static ssize_t show_pwm(struct device *dev, struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + return sprintf(buf, "%d\n", data->pwm[attr->index]); +} + +static ssize_t set_pwm(struct device *dev, struct device_attribute *devattr, + const char *buf, size_t count) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + int temp = simple_strtol(buf, NULL, 10); + + mutex_lock(&data->lock); + data->pwm[attr->index] = temp; + i2c_smbus_write_byte_data(client, ADT7473_REG_PWM(attr->index), temp); + mutex_unlock(&data->lock); + + return count; +} + +static ssize_t show_pwm_max(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + return sprintf(buf, "%d\n", data->pwm_max[attr->index]); +} + +static ssize_t set_pwm_max(struct device *dev, + struct device_attribute *devattr, + const char *buf, + size_t count) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + int temp = simple_strtol(buf, NULL, 10); + + mutex_lock(&data->lock); + data->pwm_max[attr->index] = temp; + i2c_smbus_write_byte_data(client, ADT7473_REG_PWM_MAX(attr->index), + temp); + mutex_unlock(&data->lock); + + return count; +} + +static ssize_t show_pwm_min(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + return sprintf(buf, "%d\n", data->pwm_min[attr->index]); +} + +static ssize_t set_pwm_min(struct device *dev, + struct device_attribute *devattr, + const char *buf, + size_t count) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + int temp = simple_strtol(buf, NULL, 10); + + mutex_lock(&data->lock); + data->pwm_min[attr->index] = temp; + i2c_smbus_write_byte_data(client, ADT7473_REG_PWM_MIN(attr->index), + temp); + mutex_unlock(&data->lock); + + return count; +} + +static ssize_t show_temp_tmax(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + return sprintf(buf, "%d\n", + 1000 * decode_temp(data, data->temp_tmax[attr->index])); +} + +static ssize_t set_temp_tmax(struct device *dev, + struct device_attribute *devattr, + const char *buf, + size_t count) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + int temp = simple_strtol(buf, NULL, 10) / 1000; + temp = encode_temp(data, temp); + + mutex_lock(&data->lock); + data->temp_tmax[attr->index] = temp; + i2c_smbus_write_byte_data(client, ADT7473_REG_TEMP_TMAX(attr->index), + temp); + mutex_unlock(&data->lock); + + return count; +} + +static ssize_t show_temp_tmin(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + return sprintf(buf, "%d\n", + 1000 * decode_temp(data, data->temp_tmin[attr->index])); +} + +static ssize_t set_temp_tmin(struct device *dev, + struct device_attribute *devattr, + const char *buf, + size_t count) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + int temp = simple_strtol(buf, NULL, 10) / 1000; + temp = encode_temp(data, temp); + + mutex_lock(&data->lock); + data->temp_tmin[attr->index] = temp; + i2c_smbus_write_byte_data(client, ADT7473_REG_TEMP_TMIN(attr->index), + temp); + mutex_unlock(&data->lock); + + return count; +} + +static ssize_t show_pwm_enable(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + + switch (data->pwm_behavior[attr->index] >> ADT7473_PWM_BHVR_SHIFT) { + case 3: + return sprintf(buf, "0\n"); + case 7: + return sprintf(buf, "1\n"); + default: + return sprintf(buf, "2\n"); + } +} + +static ssize_t set_pwm_enable(struct device *dev, + struct device_attribute *devattr, + const char *buf, + size_t count) +{ + u8 reg; + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + int temp = simple_strtol(buf, NULL, 10); + + switch (temp) { + case 0: + temp = 3; + break; + case 1: + temp = 7; + break; + case 2: + /* Enter automatic mode with fans off */ + temp = 4; + break; + default: + return -EINVAL; + } + + mutex_lock(&data->lock); + reg = i2c_smbus_read_byte_data(client, + ADT7473_REG_PWM_BHVR(attr->index)); + reg = (temp << ADT7473_PWM_BHVR_SHIFT) | + (reg & ~ADT7473_PWM_BHVR_MASK); + i2c_smbus_write_byte_data(client, ADT7473_REG_PWM_BHVR(attr->index), + reg); + data->pwm_behavior[attr->index] = reg; + mutex_unlock(&data->lock); + + return count; +} + +static ssize_t show_pwm_auto_temp(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + int bhvr = data->pwm_behavior[attr->index] >> ADT7473_PWM_BHVR_SHIFT; + + switch (bhvr) { + case 3: + case 4: + case 7: + return sprintf(buf, "0\n"); + case 0: + case 1: + case 5: + case 6: + return sprintf(buf, "%d\n", bhvr + 1); + case 2: + return sprintf(buf, "4\n"); + } + /* shouldn't ever get here */ + BUG(); +} + +static ssize_t set_pwm_auto_temp(struct device *dev, + struct device_attribute *devattr, + const char *buf, + size_t count) +{ + u8 reg; + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct i2c_client *client = to_i2c_client(dev); + struct adt7473_data *data = i2c_get_clientdata(client); + int temp = simple_strtol(buf, NULL, 10); + + switch (temp) { + case 1: + case 2: + case 6: + case 7: + temp--; + break; + case 0: + temp = 4; + break; + default: + return -EINVAL; + } + + mutex_lock(&data->lock); + reg = i2c_smbus_read_byte_data(client, + ADT7473_REG_PWM_BHVR(attr->index)); + reg = (temp << ADT7473_PWM_BHVR_SHIFT) | + (reg & ~ADT7473_PWM_BHVR_MASK); + i2c_smbus_write_byte_data(client, ADT7473_REG_PWM_BHVR(attr->index), + reg); + data->pwm_behavior[attr->index] = reg; + mutex_unlock(&data->lock); + + return count; +} + +static ssize_t show_alarm(struct device *dev, + struct device_attribute *devattr, + char *buf) +{ + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + struct adt7473_data *data = adt7473_update_device(dev); + + if (data->alarm & attr->index) + return sprintf(buf, "1\n"); + else + return sprintf(buf, "0\n"); +} + + +static SENSOR_DEVICE_ATTR(in1_max, S_IWUSR | S_IRUGO, show_volt_max, + set_volt_max, 0); +static SENSOR_DEVICE_ATTR(in2_max, S_IWUSR | S_IRUGO, show_volt_max, + set_volt_max, 1); + +static SENSOR_DEVICE_ATTR(in1_min, S_IWUSR | S_IRUGO, show_volt_min, + set_volt_min, 0); +static SENSOR_DEVICE_ATTR(in2_min, S_IWUSR | S_IRUGO, show_volt_min, + set_volt_min, 1); + +static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, show_volt, NULL, 0); +static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, show_volt, NULL, 1); + +static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, + ADT7473_VCCP_ALARM); +static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, + ADT7473_VCC_ALARM); + +static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_temp_max, + set_temp_max, 0); +static SENSOR_DEVICE_ATTR(temp2_max, S_IWUSR | S_IRUGO, show_temp_max, + set_temp_max, 1); +static SENSOR_DEVICE_ATTR(temp3_max, S_IWUSR | S_IRUGO, show_temp_max, + set_temp_max, 2); + +static SENSOR_DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO, show_temp_min, + set_temp_min, 0); +static SENSOR_DEVICE_ATTR(temp2_min, S_IWUSR | S_IRUGO, show_temp_min, + set_temp_min, 1); +static SENSOR_DEVICE_ATTR(temp3_min, S_IWUSR | S_IRUGO, show_temp_min, + set_temp_min, 2); + +static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL, 0); +static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_temp, NULL, 1); +static SENSOR_DEVICE_ATTR(temp3_input, S_IRUGO, show_temp, NULL, 2); + +static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, + ADT7473_R1T_ALARM | ALARM2(ADT7473_R1T_SHORT)); +static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, + ADT7473_LT_ALARM); +static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, + ADT7473_R2T_ALARM | ALARM2(ADT7473_R2T_SHORT)); + +static SENSOR_DEVICE_ATTR(fan1_min, S_IWUSR | S_IRUGO, show_fan_min, + set_fan_min, 0); +static SENSOR_DEVICE_ATTR(fan2_min, S_IWUSR | S_IRUGO, show_fan_min, + set_fan_min, 1); +static SENSOR_DEVICE_ATTR(fan3_min, S_IWUSR | S_IRUGO, show_fan_min, + set_fan_min, 2); +static SENSOR_DEVICE_ATTR(fan4_min, S_IWUSR | S_IRUGO, show_fan_min, + set_fan_min, 3); + +static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, show_fan, NULL, 0); +static SENSOR_DEVICE_ATTR(fan2_input, S_IRUGO, show_fan, NULL, 1); +static SENSOR_DEVICE_ATTR(fan3_input, S_IRUGO, show_fan, NULL, 2); +static SENSOR_DEVICE_ATTR(fan4_input, S_IRUGO, show_fan, NULL, 3); + +static SENSOR_DEVICE_ATTR(fan1_alarm, S_IRUGO, show_alarm, NULL, + ALARM2(ADT7473_FAN1_ALARM)); +static SENSOR_DEVICE_ATTR(fan2_alarm, S_IRUGO, show_alarm, NULL, + ALARM2(ADT7473_FAN2_ALARM)); +static SENSOR_DEVICE_ATTR(fan3_alarm, S_IRUGO, show_alarm, NULL, + ALARM2(ADT7473_FAN3_ALARM)); +static SENSOR_DEVICE_ATTR(fan4_alarm, S_IRUGO, show_alarm, NULL, + ALARM2(ADT7473_FAN4_ALARM)); + +static SENSOR_DEVICE_ATTR(pwm_use_point2_pwm_at_crit, S_IWUSR | S_IRUGO, + show_max_duty_at_crit, set_max_duty_at_crit, 0); + +static SENSOR_DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, show_pwm, set_pwm, 0); +static SENSOR_DEVICE_ATTR(pwm2, S_IWUSR | S_IRUGO, show_pwm, set_pwm, 1); +static SENSOR_DEVICE_ATTR(pwm3, S_IWUSR | S_IRUGO, show_pwm, set_pwm, 2); + +static SENSOR_DEVICE_ATTR(pwm1_auto_point1_pwm, S_IWUSR | S_IRUGO, + show_pwm_min, set_pwm_min, 0); +static SENSOR_DEVICE_ATTR(pwm2_auto_point1_pwm, S_IWUSR | S_IRUGO, + show_pwm_min, set_pwm_min, 1); +static SENSOR_DEVICE_ATTR(pwm3_auto_point1_pwm, S_IWUSR | S_IRUGO, + show_pwm_min, set_pwm_min, 2); + +static SENSOR_DEVICE_ATTR(pwm1_auto_point2_pwm, S_IWUSR | S_IRUGO, + show_pwm_max, set_pwm_max, 0); +static SENSOR_DEVICE_ATTR(pwm2_auto_point2_pwm, S_IWUSR | S_IRUGO, + show_pwm_max, set_pwm_max, 1); +static SENSOR_DEVICE_ATTR(pwm3_auto_point2_pwm, S_IWUSR | S_IRUGO, + show_pwm_max, set_pwm_max, 2); + +static SENSOR_DEVICE_ATTR(temp1_auto_point1_temp, S_IWUSR | S_IRUGO, + show_temp_tmin, set_temp_tmin, 0); +static SENSOR_DEVICE_ATTR(temp2_auto_point1_temp, S_IWUSR | S_IRUGO, + show_temp_tmin, set_temp_tmin, 1); +static SENSOR_DEVICE_ATTR(temp3_auto_point1_temp, S_IWUSR | S_IRUGO, + show_temp_tmin, set_temp_tmin, 2); + +static SENSOR_DEVICE_ATTR(temp1_auto_point2_temp, S_IWUSR | S_IRUGO, + show_temp_tmax, set_temp_tmax, 0); +static SENSOR_DEVICE_ATTR(temp2_auto_point2_temp, S_IWUSR | S_IRUGO, + show_temp_tmax, set_temp_tmax, 1); +static SENSOR_DEVICE_ATTR(temp3_auto_point2_temp, S_IWUSR | S_IRUGO, + show_temp_tmax, set_temp_tmax, 2); + +static SENSOR_DEVICE_ATTR(pwm1_enable, S_IWUSR | S_IRUGO, show_pwm_enable, + set_pwm_enable, 0); +static SENSOR_DEVICE_ATTR(pwm2_enable, S_IWUSR | S_IRUGO, show_pwm_enable, + set_pwm_enable, 1); +static SENSOR_DEVICE_ATTR(pwm3_enable, S_IWUSR | S_IRUGO, show_pwm_enable, + set_pwm_enable, 2); + +static SENSOR_DEVICE_ATTR(pwm1_auto_channels_temp, S_IWUSR | S_IRUGO, + show_pwm_auto_temp, set_pwm_auto_temp, 0); +static SENSOR_DEVICE_ATTR(pwm2_auto_channels_temp, S_IWUSR | S_IRUGO, + show_pwm_auto_temp, set_pwm_auto_temp, 1); +static SENSOR_DEVICE_ATTR(pwm3_auto_channels_temp, S_IWUSR | S_IRUGO, + show_pwm_auto_temp, set_pwm_auto_temp, 2); + +static struct attribute *adt7473_attr[] = +{ + &sensor_dev_attr_in1_max.dev_attr.attr, + &sensor_dev_attr_in2_max.dev_attr.attr, + &sensor_dev_attr_in1_min.dev_attr.attr, + &sensor_dev_attr_in2_min.dev_attr.attr, + &sensor_dev_attr_in1_input.dev_attr.attr, + &sensor_dev_attr_in2_input.dev_attr.attr, + &sensor_dev_attr_in1_alarm.dev_attr.attr, + &sensor_dev_attr_in2_alarm.dev_attr.attr, + + &sensor_dev_attr_temp1_max.dev_attr.attr, + &sensor_dev_attr_temp2_max.dev_attr.attr, + &sensor_dev_attr_temp3_max.dev_attr.attr, + &sensor_dev_attr_temp1_min.dev_attr.attr, + &sensor_dev_attr_temp2_min.dev_attr.attr, + &sensor_dev_attr_temp3_min.dev_attr.attr, + &sensor_dev_attr_temp1_input.dev_attr.attr, + &sensor_dev_attr_temp2_input.dev_attr.attr, + &sensor_dev_attr_temp3_input.dev_attr.attr, + &sensor_dev_attr_temp1_alarm.dev_attr.attr, + &sensor_dev_attr_temp2_alarm.dev_attr.attr, + &sensor_dev_attr_temp3_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_auto_point1_temp.dev_attr.attr, + &sensor_dev_attr_temp2_auto_point1_temp.dev_attr.attr, + &sensor_dev_attr_temp3_auto_point1_temp.dev_attr.attr, + &sensor_dev_attr_temp1_auto_point2_temp.dev_attr.attr, + &sensor_dev_attr_temp2_auto_point2_temp.dev_attr.attr, + &sensor_dev_attr_temp3_auto_point2_temp.dev_attr.attr, + + &sensor_dev_attr_fan1_min.dev_attr.attr, + &sensor_dev_attr_fan2_min.dev_attr.attr, + &sensor_dev_attr_fan3_min.dev_attr.attr, + &sensor_dev_attr_fan4_min.dev_attr.attr, + &sensor_dev_attr_fan1_input.dev_attr.attr, + &sensor_dev_attr_fan2_input.dev_attr.attr, + &sensor_dev_attr_fan3_input.dev_attr.attr, + &sensor_dev_attr_fan4_input.dev_attr.attr, + &sensor_dev_attr_fan1_alarm.dev_attr.attr, + &sensor_dev_attr_fan2_alarm.dev_attr.attr, + &sensor_dev_attr_fan3_alarm.dev_attr.attr, + &sensor_dev_attr_fan4_alarm.dev_attr.attr, + + &sensor_dev_attr_pwm_use_point2_pwm_at_crit.dev_attr.attr, + + &sensor_dev_attr_pwm1.dev_attr.attr, + &sensor_dev_attr_pwm2.dev_attr.attr, + &sensor_dev_attr_pwm3.dev_attr.attr, + &sensor_dev_attr_pwm1_auto_point1_pwm.dev_attr.attr, + &sensor_dev_attr_pwm2_auto_point1_pwm.dev_attr.attr, + &sensor_dev_attr_pwm3_auto_point1_pwm.dev_attr.attr, + &sensor_dev_attr_pwm1_auto_point2_pwm.dev_attr.attr, + &sensor_dev_attr_pwm2_auto_point2_pwm.dev_attr.attr, + &sensor_dev_attr_pwm3_auto_point2_pwm.dev_attr.attr, + + &sensor_dev_attr_pwm1_enable.dev_attr.attr, + &sensor_dev_attr_pwm2_enable.dev_attr.attr, + &sensor_dev_attr_pwm3_enable.dev_attr.attr, + &sensor_dev_attr_pwm1_auto_channels_temp.dev_attr.attr, + &sensor_dev_attr_pwm2_auto_channels_temp.dev_attr.attr, + &sensor_dev_attr_pwm3_auto_channels_temp.dev_attr.attr, + + NULL +}; + +static int adt7473_attach_adapter(struct i2c_adapter *adapter) +{ + if (!(adapter->class & I2C_CLASS_HWMON)) + return 0; + return i2c_probe(adapter, &addr_data, adt7473_detect); +} + +static int adt7473_detect(struct i2c_adapter *adapter, int address, int kind) +{ + struct i2c_client *client; + struct adt7473_data *data; + int err = 0; + + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) + goto exit; + + data = kzalloc(sizeof(struct adt7473_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + client = &data->client; + client->addr = address; + client->adapter = adapter; + client->driver = &adt7473_driver; + + i2c_set_clientdata(client, data); + + mutex_init(&data->lock); + + if (kind <= 0) { + int vendor, device, revision; + + vendor = i2c_smbus_read_byte_data(client, ADT7473_REG_VENDOR); + if (vendor != ADT7473_VENDOR) { + err = -ENODEV; + goto exit_free; + } + + device = i2c_smbus_read_byte_data(client, ADT7473_REG_DEVICE); + if (device != ADT7473_DEVICE) { + err = -ENODEV; + goto exit_free; + } + + revision = i2c_smbus_read_byte_data(client, + ADT7473_REG_REVISION); + if (revision != ADT7473_REV_68 && revision != ADT7473_REV_69) { + err = -ENODEV; + goto exit_free; + } + } else + dev_dbg(&adapter->dev, "detection forced\n"); + + strlcpy(client->name, "adt7473", I2C_NAME_SIZE); + + err = i2c_attach_client(client); + if (err) + goto exit_free; + + dev_info(&client->dev, "%s chip found\n", client->name); + + /* Initialize the ADT7473 chip */ + adt7473_init_client(client); + + /* Register sysfs hooks */ + data->attrs.attrs = adt7473_attr; + err = sysfs_create_group(&client->dev.kobj, &data->attrs); + if (err) + goto exit_detach; + + data->hwmon_dev = hwmon_device_register(&client->dev); + if (IS_ERR(data->hwmon_dev)) { + err = PTR_ERR(data->hwmon_dev); + goto exit_remove; + } + + return 0; + +exit_remove: + sysfs_remove_group(&client->dev.kobj, &data->attrs); +exit_detach: + i2c_detach_client(client); +exit_free: + kfree(data); +exit: + return err; +} + +static int adt7473_detach_client(struct i2c_client *client) +{ + struct adt7473_data *data = i2c_get_clientdata(client); + + hwmon_device_unregister(data->hwmon_dev); + sysfs_remove_group(&client->dev.kobj, &data->attrs); + i2c_detach_client(client); + kfree(data); + return 0; +} + +static int __init adt7473_init(void) +{ + return i2c_add_driver(&adt7473_driver); +} + +static void __exit adt7473_exit(void) +{ + i2c_del_driver(&adt7473_driver); +} + +MODULE_AUTHOR("Darrick J. Wong <djwong@us.ibm.com>"); +MODULE_DESCRIPTION("ADT7473 driver"); +MODULE_LICENSE("GPL"); + +module_init(adt7473_init); +module_exit(adt7473_exit); diff --git a/drivers/hwmon/applesmc.c b/drivers/hwmon/applesmc.c index 0c94770b7f8..aacc0c4b809 100644 --- a/drivers/hwmon/applesmc.c +++ b/drivers/hwmon/applesmc.c @@ -84,12 +84,15 @@ static const char* temperature_sensors_sets[][36] = { /* Set 0: Macbook Pro */ { "TA0P", "TB0T", "TC0D", "TC0P", "TG0H", "TG0P", "TG0T", "Th0H", "Th1H", "Tm0P", "Ts0P", "Ts1P", NULL }, -/* Set 1: Macbook set */ +/* Set 1: Macbook2 set */ + { "TB0T", "TC0D", "TC0P", "TM0P", "TN0P", "TN1P", "TTF0", "Th0H", + "Th0S", "Th1H", NULL }, +/* Set 2: Macbook set */ { "TB0T", "TC0D", "TC0P", "TM0P", "TN0P", "TN1P", "Th0H", "Th0S", "Th1H", "Ts0P", NULL }, -/* Set 2: Macmini set */ +/* Set 3: Macmini set */ { "TC0D", "TC0P", NULL }, -/* Set 3: Mac Pro (2 x Quad-Core) */ +/* Set 4: Mac Pro (2 x Quad-Core) */ { "TA0P", "TCAG", "TCAH", "TCBG", "TCBH", "TC0C", "TC0D", "TC0P", "TC1C", "TC1D", "TC2C", "TC2D", "TC3C", "TC3D", "THTG", "TH0P", "TH1P", "TH2P", "TH3P", "TMAP", "TMAS", "TMBS", "TM0P", "TM0S", @@ -1212,12 +1215,14 @@ static void applesmc_release_accelerometer(void) static __initdata struct dmi_match_data applesmc_dmi_data[] = { /* MacBook Pro: accelerometer, backlight and temperature set 0 */ { .accelerometer = 1, .light = 1, .temperature_set = 0 }, -/* MacBook: accelerometer and temperature set 1 */ +/* MacBook2: accelerometer and temperature set 1 */ { .accelerometer = 1, .light = 0, .temperature_set = 1 }, -/* MacMini: temperature set 2 */ - { .accelerometer = 0, .light = 0, .temperature_set = 2 }, -/* MacPro: temperature set 3 */ +/* MacBook: accelerometer and temperature set 2 */ + { .accelerometer = 1, .light = 0, .temperature_set = 2 }, +/* MacMini: temperature set 3 */ { .accelerometer = 0, .light = 0, .temperature_set = 3 }, +/* MacPro: temperature set 4 */ + { .accelerometer = 0, .light = 0, .temperature_set = 4 }, }; /* Note that DMI_MATCH(...,"MacBook") will match "MacBookPro1,1". @@ -1229,16 +1234,20 @@ static __initdata struct dmi_system_id applesmc_whitelist[] = { (void*)&applesmc_dmi_data[0]}, { applesmc_dmi_match, "Apple MacBook", { DMI_MATCH(DMI_BOARD_VENDOR,"Apple"), - DMI_MATCH(DMI_PRODUCT_NAME,"MacBook") }, + DMI_MATCH(DMI_PRODUCT_NAME,"MacBook2") }, (void*)&applesmc_dmi_data[1]}, + { applesmc_dmi_match, "Apple MacBook", { + DMI_MATCH(DMI_BOARD_VENDOR,"Apple"), + DMI_MATCH(DMI_PRODUCT_NAME,"MacBook") }, + (void*)&applesmc_dmi_data[2]}, { applesmc_dmi_match, "Apple Macmini", { DMI_MATCH(DMI_BOARD_VENDOR,"Apple"), DMI_MATCH(DMI_PRODUCT_NAME,"Macmini") }, - (void*)&applesmc_dmi_data[2]}, + (void*)&applesmc_dmi_data[3]}, { applesmc_dmi_match, "Apple MacPro2", { DMI_MATCH(DMI_BOARD_VENDOR,"Apple"), DMI_MATCH(DMI_PRODUCT_NAME,"MacPro2") }, - (void*)&applesmc_dmi_data[3]}, + (void*)&applesmc_dmi_data[4]}, { .ident = NULL } }; diff --git a/drivers/hwmon/asb100.c b/drivers/hwmon/asb100.c index 950cea8d1d6..84712a22ace 100644 --- a/drivers/hwmon/asb100.c +++ b/drivers/hwmon/asb100.c @@ -49,7 +49,7 @@ #include "lm75.h" /* I2C addresses to scan */ -static unsigned short normal_i2c[] = { 0x2d, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2d, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(asb100); diff --git a/drivers/hwmon/atxp1.c b/drivers/hwmon/atxp1.c index cce3350e539..01c17e387f0 100644 --- a/drivers/hwmon/atxp1.c +++ b/drivers/hwmon/atxp1.c @@ -42,7 +42,7 @@ MODULE_AUTHOR("Sebastian Witt <se.witt@gmx.net>"); #define ATXP1_VIDMASK 0x1f #define ATXP1_GPIO1MASK 0x0f -static unsigned short normal_i2c[] = { 0x37, 0x4e, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x37, 0x4e, I2C_CLIENT_END }; I2C_CLIENT_INSMOD_1(atxp1); diff --git a/drivers/hwmon/coretemp.c b/drivers/hwmon/coretemp.c index 3ee60d26e3a..70239acecc8 100644 --- a/drivers/hwmon/coretemp.c +++ b/drivers/hwmon/coretemp.c @@ -38,7 +38,8 @@ #define DRVNAME "coretemp" -typedef enum { SHOW_TEMP, SHOW_TJMAX, SHOW_LABEL, SHOW_NAME } SHOW; +typedef enum { SHOW_TEMP, SHOW_TJMAX, SHOW_TTARGET, SHOW_LABEL, + SHOW_NAME } SHOW; /* * Functions declaration @@ -55,6 +56,7 @@ struct coretemp_data { unsigned long last_updated; /* in jiffies */ int temp; int tjmax; + int ttarget; u8 alarm; }; @@ -93,9 +95,10 @@ static ssize_t show_temp(struct device *dev, if (attr->index == SHOW_TEMP) err = data->valid ? sprintf(buf, "%d\n", data->temp) : -EAGAIN; - else + else if (attr->index == SHOW_TJMAX) err = sprintf(buf, "%d\n", data->tjmax); - + else + err = sprintf(buf, "%d\n", data->ttarget); return err; } @@ -103,6 +106,8 @@ static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL, SHOW_TEMP); static SENSOR_DEVICE_ATTR(temp1_crit, S_IRUGO, show_temp, NULL, SHOW_TJMAX); +static SENSOR_DEVICE_ATTR(temp1_max, S_IRUGO, show_temp, NULL, + SHOW_TTARGET); static DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL); static SENSOR_DEVICE_ATTR(temp1_label, S_IRUGO, show_name, NULL, SHOW_LABEL); static SENSOR_DEVICE_ATTR(name, S_IRUGO, show_name, NULL, SHOW_NAME); @@ -147,6 +152,56 @@ static struct coretemp_data *coretemp_update_device(struct device *dev) return data; } +static int __devinit adjust_tjmax(struct cpuinfo_x86 *c, u32 id, struct device *dev) +{ + /* The 100C is default for both mobile and non mobile CPUs */ + + int tjmax = 100000; + int ismobile = 1; + int err; + u32 eax, edx; + + /* Early chips have no MSR for TjMax */ + + if ((c->x86_model == 0xf) && (c->x86_mask < 4)) { + ismobile = 0; + } + + if ((c->x86_model > 0xe) && (ismobile)) { + + /* Now we can detect the mobile CPU using Intel provided table + http://softwarecommunity.intel.com/Wiki/Mobility/720.htm + For Core2 cores, check MSR 0x17, bit 28 1 = Mobile CPU + */ + + err = rdmsr_safe_on_cpu(id, 0x17, &eax, &edx); + if (err) { + dev_warn(dev, + "Unable to access MSR 0x17, assuming desktop" + " CPU\n"); + ismobile = 0; + } else if (!(eax & 0x10000000)) { + ismobile = 0; + } + } + + if (ismobile) { + + err = rdmsr_safe_on_cpu(id, 0xee, &eax, &edx); + if (err) { + dev_warn(dev, + "Unable to access MSR 0xEE, for Tjmax, left" + " at default"); + } else if (eax & 0x40000000) { + tjmax = 85000; + } + } else { + dev_warn(dev, "Using relative temperature scale!\n"); + } + + return tjmax; +} + static int __devinit coretemp_probe(struct platform_device *pdev) { struct coretemp_data *data; @@ -163,8 +218,6 @@ static int __devinit coretemp_probe(struct platform_device *pdev) data->id = pdev->id; data->name = "coretemp"; mutex_init(&data->update_lock); - /* Tjmax default is 100 degrees C */ - data->tjmax = 100000; /* test if we can access the THERM_STATUS MSR */ err = rdmsr_safe_on_cpu(data->id, MSR_IA32_THERM_STATUS, &eax, &edx); @@ -191,40 +244,29 @@ static int __devinit coretemp_probe(struct platform_device *pdev) } } - /* Some processors have Tjmax 85 following magic should detect it - Intel won't disclose the information without signed NDA, but - individuals cannot sign it. Catch(ed) 22. - */ + data->tjmax = adjust_tjmax(c, data->id, &pdev->dev); + platform_set_drvdata(pdev, data); - if (((c->x86_model == 0xf) && (c->x86_mask > 3)) || - (c->x86_model == 0xe)) { - err = rdmsr_safe_on_cpu(data->id, 0xee, &eax, &edx); + /* read the still undocumented IA32_TEMPERATURE_TARGET it exists + on older CPUs but not in this register */ + + if (c->x86_model > 0xe) { + err = rdmsr_safe_on_cpu(data->id, 0x1a2, &eax, &edx); if (err) { - dev_warn(&pdev->dev, - "Unable to access MSR 0xEE, Tjmax left at %d " - "degrees C\n", data->tjmax/1000); - } else if (eax & 0x40000000) { - data->tjmax = 85000; + dev_warn(&pdev->dev, "Unable to read" + " IA32_TEMPERATURE_TARGET MSR\n"); + } else { + data->ttarget = data->tjmax - + (((eax >> 8) & 0xff) * 1000); + err = device_create_file(&pdev->dev, + &sensor_dev_attr_temp1_max.dev_attr); + if (err) + goto exit_free; } } - /* Intel says that above should not work for desktop Core2 processors, - but it seems to work. There is no other way how get the absolute - readings. Warn the user about this. First check if are desktop, - bit 50 of MSR_IA32_PLATFORM_ID should be 0. - */ - - rdmsr_safe_on_cpu(data->id, MSR_IA32_PLATFORM_ID, &eax, &edx); - - if ((c->x86_model == 0xf) && (!(edx & 0x00040000))) { - dev_warn(&pdev->dev, "Using undocumented features, absolute " - "temperature might be wrong!\n"); - } - - platform_set_drvdata(pdev, data); - if ((err = sysfs_create_group(&pdev->dev.kobj, &coretemp_group))) - goto exit_free; + goto exit_dev; data->hwmon_dev = hwmon_device_register(&pdev->dev); if (IS_ERR(data->hwmon_dev)) { @@ -238,6 +280,8 @@ static int __devinit coretemp_probe(struct platform_device *pdev) exit_class: sysfs_remove_group(&pdev->dev.kobj, &coretemp_group); +exit_dev: + device_remove_file(&pdev->dev, &sensor_dev_attr_temp1_max.dev_attr); exit_free: kfree(data); exit: @@ -250,6 +294,7 @@ static int __devexit coretemp_remove(struct platform_device *pdev) hwmon_device_unregister(data->hwmon_dev); sysfs_remove_group(&pdev->dev.kobj, &coretemp_group); + device_remove_file(&pdev->dev, &sensor_dev_attr_temp1_max.dev_attr); platform_set_drvdata(pdev, NULL); kfree(data); return 0; @@ -330,7 +375,7 @@ static void coretemp_device_remove(unsigned int cpu) mutex_unlock(&pdev_list_mutex); } -static int coretemp_cpu_callback(struct notifier_block *nfb, +static int __cpuinit coretemp_cpu_callback(struct notifier_block *nfb, unsigned long action, void *hcpu) { unsigned int cpu = (unsigned long) hcpu; @@ -347,7 +392,7 @@ static int coretemp_cpu_callback(struct notifier_block *nfb, return NOTIFY_OK; } -static struct notifier_block coretemp_cpu_notifier = { +static struct notifier_block coretemp_cpu_notifier __refdata = { .notifier_call = coretemp_cpu_callback, }; #endif /* !CONFIG_HOTPLUG_CPU */ @@ -368,10 +413,10 @@ static int __init coretemp_init(void) for_each_online_cpu(i) { struct cpuinfo_x86 *c = &cpu_data(i); - /* check if family 6, models e, f, 16 */ + /* check if family 6, models 0xe, 0xf, 0x16, 0x17 */ if ((c->cpuid_level < 0) || (c->x86 != 0x6) || !((c->x86_model == 0xe) || (c->x86_model == 0xf) || - (c->x86_model == 0x16))) { + (c->x86_model == 0x16) || (c->x86_model == 0x17))) { /* supported CPU not found, but report the unknown family 6 CPU */ diff --git a/drivers/hwmon/dme1737.c b/drivers/hwmon/dme1737.c index ddddd9f34c1..7673f65877e 100644 --- a/drivers/hwmon/dme1737.c +++ b/drivers/hwmon/dme1737.c @@ -49,7 +49,7 @@ module_param(force_id, ushort, 0); MODULE_PARM_DESC(force_id, "Override the detected device ID"); /* Addresses to scan */ -static unsigned short normal_i2c[] = {0x2c, 0x2d, 0x2e, I2C_CLIENT_END}; +static const unsigned short normal_i2c[] = {0x2c, 0x2d, 0x2e, I2C_CLIENT_END}; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(dme1737); diff --git a/drivers/hwmon/ds1621.c b/drivers/hwmon/ds1621.c index 3f5163de13c..5f300ffed65 100644 --- a/drivers/hwmon/ds1621.c +++ b/drivers/hwmon/ds1621.c @@ -34,7 +34,7 @@ #include "lm75.h" /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c, +static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c, 0x4d, 0x4e, 0x4f, I2C_CLIENT_END }; /* Insmod parameters */ diff --git a/drivers/hwmon/f75375s.c b/drivers/hwmon/f75375s.c index 6892f76fc18..1464338e4e1 100644 --- a/drivers/hwmon/f75375s.c +++ b/drivers/hwmon/f75375s.c @@ -37,7 +37,7 @@ #include <linux/f75375s.h> /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2d, 0x2e, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2d, 0x2e, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_2(f75373, f75375); diff --git a/drivers/hwmon/fscher.c b/drivers/hwmon/fscher.c index 721c70177b1..ed26b66e083 100644 --- a/drivers/hwmon/fscher.c +++ b/drivers/hwmon/fscher.c @@ -40,7 +40,7 @@ * Addresses to scan */ -static unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END }; /* * Insmod parameters diff --git a/drivers/hwmon/fschmd.c b/drivers/hwmon/fschmd.c index b7c9eef0f92..bd89d270a5e 100644 --- a/drivers/hwmon/fschmd.c +++ b/drivers/hwmon/fschmd.c @@ -44,7 +44,7 @@ #include <linux/dmi.h> /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_5(fscpos, fscher, fscscy, fschrc, fschmd); diff --git a/drivers/hwmon/fscpos.c b/drivers/hwmon/fscpos.c index 2f1075323a1..00f48484e54 100644 --- a/drivers/hwmon/fscpos.c +++ b/drivers/hwmon/fscpos.c @@ -43,7 +43,7 @@ /* * Addresses to scan */ -static unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END }; /* * Insmod parameters diff --git a/drivers/hwmon/gl518sm.c b/drivers/hwmon/gl518sm.c index 3b1ac48fce2..33e9e8a8d1c 100644 --- a/drivers/hwmon/gl518sm.c +++ b/drivers/hwmon/gl518sm.c @@ -44,7 +44,7 @@ #include <linux/sysfs.h> /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_2(gl518sm_r00, gl518sm_r80); diff --git a/drivers/hwmon/gl520sm.c b/drivers/hwmon/gl520sm.c index 03ecdc33476..8984ef14162 100644 --- a/drivers/hwmon/gl520sm.c +++ b/drivers/hwmon/gl520sm.c @@ -39,7 +39,7 @@ module_param(extra_sensor_type, ushort, 0); MODULE_PARM_DESC(extra_sensor_type, "Type of extra sensor (0=autodetect, 1=temperature, 2=voltage)"); /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(gl520sm); diff --git a/drivers/hwmon/lm63.c b/drivers/hwmon/lm63.c index 650b07d5b90..11628700808 100644 --- a/drivers/hwmon/lm63.c +++ b/drivers/hwmon/lm63.c @@ -53,7 +53,7 @@ * Address is fully defined internally and cannot be changed. */ -static unsigned short normal_i2c[] = { 0x4c, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x4c, I2C_CLIENT_END }; /* * Insmod parameters diff --git a/drivers/hwmon/lm75.c b/drivers/hwmon/lm75.c index e5c35a355a5..115f4090b98 100644 --- a/drivers/hwmon/lm75.c +++ b/drivers/hwmon/lm75.c @@ -31,7 +31,7 @@ /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c, +static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c, 0x4d, 0x4e, 0x4f, I2C_CLIENT_END }; /* Insmod parameters */ diff --git a/drivers/hwmon/lm77.c b/drivers/hwmon/lm77.c index 459b70ad6be..36d5a8c3ad8 100644 --- a/drivers/hwmon/lm77.c +++ b/drivers/hwmon/lm77.c @@ -36,7 +36,8 @@ #include <linux/mutex.h> /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, + I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(lm77); diff --git a/drivers/hwmon/lm78.c b/drivers/hwmon/lm78.c index 0a9eb1f6f4e..ed7859f0e16 100644 --- a/drivers/hwmon/lm78.c +++ b/drivers/hwmon/lm78.c @@ -37,8 +37,8 @@ static struct platform_device *pdev; /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d, - 0x2e, 0x2f, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d, + 0x2e, 0x2f, I2C_CLIENT_END }; static unsigned short isa_address = 0x290; /* Insmod parameters */ diff --git a/drivers/hwmon/lm80.c b/drivers/hwmon/lm80.c index a2ca055f392..26c91c9d476 100644 --- a/drivers/hwmon/lm80.c +++ b/drivers/hwmon/lm80.c @@ -32,8 +32,8 @@ #include <linux/mutex.h> /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, - 0x2d, 0x2e, 0x2f, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d, + 0x2e, 0x2f, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(lm80); diff --git a/drivers/hwmon/lm83.c b/drivers/hwmon/lm83.c index 6e8903a6e90..6a8642fa25f 100644 --- a/drivers/hwmon/lm83.c +++ b/drivers/hwmon/lm83.c @@ -48,10 +48,8 @@ * addresses. */ -static unsigned short normal_i2c[] = { 0x18, 0x19, 0x1a, - 0x29, 0x2a, 0x2b, - 0x4c, 0x4d, 0x4e, - I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { + 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, 0x4d, 0x4e, I2C_CLIENT_END }; /* * Insmod parameters diff --git a/drivers/hwmon/lm85.c b/drivers/hwmon/lm85.c index 4bb0f291a6b..182fe6a5605 100644 --- a/drivers/hwmon/lm85.c +++ b/drivers/hwmon/lm85.c @@ -35,7 +35,7 @@ #include <linux/mutex.h> /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_6(lm85b, lm85c, adm1027, adt7463, emc6d100, emc6d102); diff --git a/drivers/hwmon/lm87.c b/drivers/hwmon/lm87.c index 8ee07c5c97a..e1c183f0aae 100644 --- a/drivers/hwmon/lm87.c +++ b/drivers/hwmon/lm87.c @@ -73,7 +73,7 @@ * LM87 has three possible addresses: 0x2c, 0x2d and 0x2e. */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; /* * Insmod parameters diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c index f7ec95bedbf..d1a3da3dd8e 100644 --- a/drivers/hwmon/lm90.c +++ b/drivers/hwmon/lm90.c @@ -101,10 +101,8 @@ * 0x4c, 0x4d or 0x4e. */ -static unsigned short normal_i2c[] = { 0x18, 0x19, 0x1a, - 0x29, 0x2a, 0x2b, - 0x4c, 0x4d, 0x4e, - I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { + 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, 0x4d, 0x4e, I2C_CLIENT_END }; /* * Insmod parameters diff --git a/drivers/hwmon/lm92.c b/drivers/hwmon/lm92.c index af5c77d568f..c31942e0824 100644 --- a/drivers/hwmon/lm92.c +++ b/drivers/hwmon/lm92.c @@ -45,13 +45,14 @@ #include <linux/slab.h> #include <linux/i2c.h> #include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> #include <linux/err.h> #include <linux/mutex.h> /* The LM92 and MAX6635 have 2 two-state pins for address selection, resulting in 4 possible addresses. */ -static unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, - I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, + I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(lm92); @@ -209,6 +210,14 @@ static ssize_t show_alarms(struct device *dev, struct device_attribute *attr, ch return sprintf(buf, "%d\n", ALARMS_FROM_REG(data->temp1_input)); } +static ssize_t show_alarm(struct device *dev, struct device_attribute *attr, + char *buf) +{ + int bitnr = to_sensor_dev_attr(attr)->index; + struct lm92_data *data = lm92_update_device(dev); + return sprintf(buf, "%d\n", (data->temp1_input >> bitnr) & 1); +} + static DEVICE_ATTR(temp1_input, S_IRUGO, show_temp1_input, NULL); static DEVICE_ATTR(temp1_crit, S_IWUSR | S_IRUGO, show_temp1_crit, set_temp1_crit); @@ -221,6 +230,9 @@ static DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_temp1_max, set_temp1_max); static DEVICE_ATTR(temp1_max_hyst, S_IRUGO, show_temp1_max_hyst, NULL); static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL); +static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, 2); +static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL, 0); +static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 1); /* @@ -297,7 +309,9 @@ static struct attribute *lm92_attributes[] = { &dev_attr_temp1_max.attr, &dev_attr_temp1_max_hyst.attr, &dev_attr_alarms.attr, - + &sensor_dev_attr_temp1_crit_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_min_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_max_alarm.dev_attr.attr, NULL }; diff --git a/drivers/hwmon/lm93.c b/drivers/hwmon/lm93.c index ea61946a4bf..5e678f5c883 100644 --- a/drivers/hwmon/lm93.c +++ b/drivers/hwmon/lm93.c @@ -142,7 +142,7 @@ I2C_FUNC_SMBUS_WORD_DATA) /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(lm93); diff --git a/drivers/hwmon/max1619.c b/drivers/hwmon/max1619.c index 38a44c3d6ce..7e7267a0454 100644 --- a/drivers/hwmon/max1619.c +++ b/drivers/hwmon/max1619.c @@ -32,14 +32,13 @@ #include <linux/jiffies.h> #include <linux/i2c.h> #include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> #include <linux/err.h> #include <linux/mutex.h> #include <linux/sysfs.h> -static unsigned short normal_i2c[] = { 0x18, 0x19, 0x1a, - 0x29, 0x2a, 0x2b, - 0x4c, 0x4d, 0x4e, - I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { + 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, 0x4d, 0x4e, I2C_CLIENT_END }; /* * Insmod parameters @@ -161,6 +160,14 @@ static ssize_t show_alarms(struct device *dev, struct device_attribute *attr, ch return sprintf(buf, "%d\n", data->alarms); } +static ssize_t show_alarm(struct device *dev, struct device_attribute *attr, + char *buf) +{ + int bitnr = to_sensor_dev_attr(attr)->index; + struct max1619_data *data = max1619_update_device(dev); + return sprintf(buf, "%d\n", (data->alarms >> bitnr) & 1); +} + static DEVICE_ATTR(temp1_input, S_IRUGO, show_temp_input1, NULL); static DEVICE_ATTR(temp2_input, S_IRUGO, show_temp_input2, NULL); static DEVICE_ATTR(temp2_min, S_IWUSR | S_IRUGO, show_temp_low2, @@ -172,6 +179,10 @@ static DEVICE_ATTR(temp2_crit, S_IWUSR | S_IRUGO, show_temp_crit2, static DEVICE_ATTR(temp2_crit_hyst, S_IWUSR | S_IRUGO, show_temp_hyst2, set_temp_hyst2); static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL); +static SENSOR_DEVICE_ATTR(temp2_crit_alarm, S_IRUGO, show_alarm, NULL, 1); +static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, 2); +static SENSOR_DEVICE_ATTR(temp2_min_alarm, S_IRUGO, show_alarm, NULL, 3); +static SENSOR_DEVICE_ATTR(temp2_max_alarm, S_IRUGO, show_alarm, NULL, 4); static struct attribute *max1619_attributes[] = { &dev_attr_temp1_input.attr, @@ -182,6 +193,10 @@ static struct attribute *max1619_attributes[] = { &dev_attr_temp2_crit_hyst.attr, &dev_attr_alarms.attr, + &sensor_dev_attr_temp2_crit_alarm.dev_attr.attr, + &sensor_dev_attr_temp2_fault.dev_attr.attr, + &sensor_dev_attr_temp2_min_alarm.dev_attr.attr, + &sensor_dev_attr_temp2_max_alarm.dev_attr.attr, NULL }; diff --git a/drivers/hwmon/max6650.c b/drivers/hwmon/max6650.c index 755570c1f4e..52d528b76cc 100644 --- a/drivers/hwmon/max6650.c +++ b/drivers/hwmon/max6650.c @@ -44,7 +44,8 @@ * Addresses to scan. There are four disjoint possibilities, by pin config. */ -static unsigned short normal_i2c[] = {0x1b, 0x1f, 0x48, 0x4b, I2C_CLIENT_END}; +static const unsigned short normal_i2c[] = {0x1b, 0x1f, 0x48, 0x4b, + I2C_CLIENT_END}; /* * Insmod parameters diff --git a/drivers/hwmon/smsc47m1.c b/drivers/hwmon/smsc47m1.c index 0d7f0c4d06b..d1b49854873 100644 --- a/drivers/hwmon/smsc47m1.c +++ b/drivers/hwmon/smsc47m1.c @@ -198,6 +198,14 @@ static ssize_t get_fan_div(struct device *dev, struct device_attribute return sprintf(buf, "%d\n", DIV_FROM_REG(data->fan_div[attr->index])); } +static ssize_t get_fan_alarm(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + int bitnr = to_sensor_dev_attr(devattr)->index; + struct smsc47m1_data *data = smsc47m1_update_device(dev, 0); + return sprintf(buf, "%u\n", (data->alarms >> bitnr) & 1); +} + static ssize_t get_pwm(struct device *dev, struct device_attribute *devattr, char *buf) { @@ -347,6 +355,8 @@ static SENSOR_DEVICE_ATTR(fan##offset##_min, S_IRUGO | S_IWUSR, \ get_fan_min, set_fan_min, offset - 1); \ static SENSOR_DEVICE_ATTR(fan##offset##_div, S_IRUGO | S_IWUSR, \ get_fan_div, set_fan_div, offset - 1); \ +static SENSOR_DEVICE_ATTR(fan##offset##_alarm, S_IRUGO, get_fan_alarm, \ + NULL, offset - 1); \ static SENSOR_DEVICE_ATTR(pwm##offset, S_IRUGO | S_IWUSR, \ get_pwm, set_pwm, offset - 1); \ static SENSOR_DEVICE_ATTR(pwm##offset##_enable, S_IRUGO | S_IWUSR, \ @@ -374,12 +384,15 @@ static struct attribute *smsc47m1_attributes[] = { &sensor_dev_attr_fan1_input.dev_attr.attr, &sensor_dev_attr_fan1_min.dev_attr.attr, &sensor_dev_attr_fan1_div.dev_attr.attr, + &sensor_dev_attr_fan1_alarm.dev_attr.attr, &sensor_dev_attr_fan2_input.dev_attr.attr, &sensor_dev_attr_fan2_min.dev_attr.attr, &sensor_dev_attr_fan2_div.dev_attr.attr, + &sensor_dev_attr_fan2_alarm.dev_attr.attr, &sensor_dev_attr_fan3_input.dev_attr.attr, &sensor_dev_attr_fan3_min.dev_attr.attr, &sensor_dev_attr_fan3_div.dev_attr.attr, + &sensor_dev_attr_fan3_alarm.dev_attr.attr, &sensor_dev_attr_pwm1.dev_attr.attr, &sensor_dev_attr_pwm1_enable.dev_attr.attr, @@ -533,7 +546,9 @@ static int __devinit smsc47m1_probe(struct platform_device *pdev) || (err = device_create_file(dev, &sensor_dev_attr_fan1_min.dev_attr)) || (err = device_create_file(dev, - &sensor_dev_attr_fan1_div.dev_attr))) + &sensor_dev_attr_fan1_div.dev_attr)) + || (err = device_create_file(dev, + &sensor_dev_attr_fan1_alarm.dev_attr))) goto error_remove_files; } else dev_dbg(dev, "Fan 1 not enabled by hardware, skipping\n"); @@ -544,7 +559,9 @@ static int __devinit smsc47m1_probe(struct platform_device *pdev) || (err = device_create_file(dev, &sensor_dev_attr_fan2_min.dev_attr)) || (err = device_create_file(dev, - &sensor_dev_attr_fan2_div.dev_attr))) + &sensor_dev_attr_fan2_div.dev_attr)) + || (err = device_create_file(dev, + &sensor_dev_attr_fan2_alarm.dev_attr))) goto error_remove_files; } else dev_dbg(dev, "Fan 2 not enabled by hardware, skipping\n"); @@ -555,7 +572,9 @@ static int __devinit smsc47m1_probe(struct platform_device *pdev) || (err = device_create_file(dev, &sensor_dev_attr_fan3_min.dev_attr)) || (err = device_create_file(dev, - &sensor_dev_attr_fan3_div.dev_attr))) + &sensor_dev_attr_fan3_div.dev_attr)) + || (err = device_create_file(dev, + &sensor_dev_attr_fan3_alarm.dev_attr))) goto error_remove_files; } else if (data->type == smsc47m2) dev_dbg(dev, "Fan 3 not enabled by hardware, skipping\n"); diff --git a/drivers/hwmon/smsc47m192.c b/drivers/hwmon/smsc47m192.c index 8b0c188e60f..3c9db6598ba 100644 --- a/drivers/hwmon/smsc47m192.c +++ b/drivers/hwmon/smsc47m192.c @@ -34,7 +34,7 @@ #include <linux/mutex.h> /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(smsc47m192); diff --git a/drivers/hwmon/thmc50.c b/drivers/hwmon/thmc50.c index 04dd7699b3a..76a3859c3fb 100644 --- a/drivers/hwmon/thmc50.c +++ b/drivers/hwmon/thmc50.c @@ -32,7 +32,7 @@ MODULE_LICENSE("GPL"); /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_2(thmc50, adm1022); @@ -52,9 +52,9 @@ I2C_CLIENT_MODULE_PARM(adm1022_temp3, "List of adapter,address pairs " */ #define THMC50_REG_INTR 0x41 -const static u8 THMC50_REG_TEMP[] = { 0x27, 0x26, 0x20 }; -const static u8 THMC50_REG_TEMP_MIN[] = { 0x3A, 0x38, 0x2C }; -const static u8 THMC50_REG_TEMP_MAX[] = { 0x39, 0x37, 0x2B }; +static const u8 THMC50_REG_TEMP[] = { 0x27, 0x26, 0x20 }; +static const u8 THMC50_REG_TEMP_MIN[] = { 0x3A, 0x38, 0x2C }; +static const u8 THMC50_REG_TEMP_MAX[] = { 0x39, 0x37, 0x2B }; #define THMC50_REG_CONF_nFANOFF 0x20 diff --git a/drivers/hwmon/via686a.c b/drivers/hwmon/via686a.c index 2635bba1e3f..f1ee5e73196 100644 --- a/drivers/hwmon/via686a.c +++ b/drivers/hwmon/via686a.c @@ -533,6 +533,24 @@ static ssize_t show_alarms(struct device *dev, struct device_attribute *attr, ch } static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL); +static ssize_t show_alarm(struct device *dev, struct device_attribute *attr, + char *buf) +{ + int bitnr = to_sensor_dev_attr(attr)->index; + struct via686a_data *data = via686a_update_device(dev); + return sprintf(buf, "%u\n", (data->alarms >> bitnr) & 1); +} +static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0); +static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 1); +static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 2); +static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 3); +static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 8); +static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 4); +static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 11); +static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 15); +static SENSOR_DEVICE_ATTR(fan1_alarm, S_IRUGO, show_alarm, NULL, 6); +static SENSOR_DEVICE_ATTR(fan2_alarm, S_IRUGO, show_alarm, NULL, 7); + static ssize_t show_name(struct device *dev, struct device_attribute *devattr, char *buf) { @@ -557,6 +575,11 @@ static struct attribute *via686a_attributes[] = { &sensor_dev_attr_in2_max.dev_attr.attr, &sensor_dev_attr_in3_max.dev_attr.attr, &sensor_dev_attr_in4_max.dev_attr.attr, + &sensor_dev_attr_in0_alarm.dev_attr.attr, + &sensor_dev_attr_in1_alarm.dev_attr.attr, + &sensor_dev_attr_in2_alarm.dev_attr.attr, + &sensor_dev_attr_in3_alarm.dev_attr.attr, + &sensor_dev_attr_in4_alarm.dev_attr.attr, &sensor_dev_attr_temp1_input.dev_attr.attr, &sensor_dev_attr_temp2_input.dev_attr.attr, @@ -567,6 +590,9 @@ static struct attribute *via686a_attributes[] = { &sensor_dev_attr_temp1_max_hyst.dev_attr.attr, &sensor_dev_attr_temp2_max_hyst.dev_attr.attr, &sensor_dev_attr_temp3_max_hyst.dev_attr.attr, + &sensor_dev_attr_temp1_alarm.dev_attr.attr, + &sensor_dev_attr_temp2_alarm.dev_attr.attr, + &sensor_dev_attr_temp3_alarm.dev_attr.attr, &sensor_dev_attr_fan1_input.dev_attr.attr, &sensor_dev_attr_fan2_input.dev_attr.attr, @@ -574,6 +600,8 @@ static struct attribute *via686a_attributes[] = { &sensor_dev_attr_fan2_min.dev_attr.attr, &sensor_dev_attr_fan1_div.dev_attr.attr, &sensor_dev_attr_fan2_div.dev_attr.attr, + &sensor_dev_attr_fan1_alarm.dev_attr.attr, + &sensor_dev_attr_fan2_alarm.dev_attr.attr, &dev_attr_alarms.attr, &dev_attr_name.attr, diff --git a/drivers/hwmon/vt8231.c b/drivers/hwmon/vt8231.c index f87661775fe..5bc57275cae 100644 --- a/drivers/hwmon/vt8231.c +++ b/drivers/hwmon/vt8231.c @@ -2,7 +2,7 @@ vt8231.c - Part of lm_sensors, Linux kernel modules for hardware monitoring - Copyright (c) 2005 Roger Lucas <roger@planbit.co.uk> + Copyright (c) 2005 Roger Lucas <vt8231@hiddenengine.co.uk> Copyright (c) 2002 Mark D. Studebaker <mdsxyz123@yahoo.com> Aaron M. Marsh <amarsh@sdf.lonestar.org> @@ -541,6 +541,28 @@ static ssize_t show_alarms(struct device *dev, struct device_attribute *attr, } static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL); +static ssize_t show_alarm(struct device *dev, struct device_attribute *attr, + char *buf) +{ + int bitnr = to_sensor_dev_attr(attr)->index; + struct vt8231_data *data = vt8231_update_device(dev); + return sprintf(buf, "%u\n", (data->alarms >> bitnr) & 1); +} +static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 4); +static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 11); +static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 0); +static SENSOR_DEVICE_ATTR(temp4_alarm, S_IRUGO, show_alarm, NULL, 1); +static SENSOR_DEVICE_ATTR(temp5_alarm, S_IRUGO, show_alarm, NULL, 3); +static SENSOR_DEVICE_ATTR(temp6_alarm, S_IRUGO, show_alarm, NULL, 8); +static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 11); +static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 0); +static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 1); +static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 3); +static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 8); +static SENSOR_DEVICE_ATTR(in5_alarm, S_IRUGO, show_alarm, NULL, 2); +static SENSOR_DEVICE_ATTR(fan1_alarm, S_IRUGO, show_alarm, NULL, 6); +static SENSOR_DEVICE_ATTR(fan2_alarm, S_IRUGO, show_alarm, NULL, 7); + static ssize_t show_name(struct device *dev, struct device_attribute *devattr, char *buf) { @@ -549,36 +571,42 @@ static ssize_t show_name(struct device *dev, struct device_attribute } static DEVICE_ATTR(name, S_IRUGO, show_name, NULL); -static struct attribute *vt8231_attributes_temps[6][4] = { +static struct attribute *vt8231_attributes_temps[6][5] = { { &dev_attr_temp1_input.attr, &dev_attr_temp1_max_hyst.attr, &dev_attr_temp1_max.attr, + &sensor_dev_attr_temp1_alarm.dev_attr.attr, NULL }, { &sensor_dev_attr_temp2_input.dev_attr.attr, &sensor_dev_attr_temp2_max_hyst.dev_attr.attr, &sensor_dev_attr_temp2_max.dev_attr.attr, + &sensor_dev_attr_temp2_alarm.dev_attr.attr, NULL }, { &sensor_dev_attr_temp3_input.dev_attr.attr, &sensor_dev_attr_temp3_max_hyst.dev_attr.attr, &sensor_dev_attr_temp3_max.dev_attr.attr, + &sensor_dev_attr_temp3_alarm.dev_attr.attr, NULL }, { &sensor_dev_attr_temp4_input.dev_attr.attr, &sensor_dev_attr_temp4_max_hyst.dev_attr.attr, &sensor_dev_attr_temp4_max.dev_attr.attr, + &sensor_dev_attr_temp4_alarm.dev_attr.attr, NULL }, { &sensor_dev_attr_temp5_input.dev_attr.attr, &sensor_dev_attr_temp5_max_hyst.dev_attr.attr, &sensor_dev_attr_temp5_max.dev_attr.attr, + &sensor_dev_attr_temp5_alarm.dev_attr.attr, NULL }, { &sensor_dev_attr_temp6_input.dev_attr.attr, &sensor_dev_attr_temp6_max_hyst.dev_attr.attr, &sensor_dev_attr_temp6_max.dev_attr.attr, + &sensor_dev_attr_temp6_alarm.dev_attr.attr, NULL } }; @@ -592,36 +620,42 @@ static const struct attribute_group vt8231_group_temps[6] = { { .attrs = vt8231_attributes_temps[5] }, }; -static struct attribute *vt8231_attributes_volts[6][4] = { +static struct attribute *vt8231_attributes_volts[6][5] = { { &sensor_dev_attr_in0_input.dev_attr.attr, &sensor_dev_attr_in0_min.dev_attr.attr, &sensor_dev_attr_in0_max.dev_attr.attr, + &sensor_dev_attr_in0_alarm.dev_attr.attr, NULL }, { &sensor_dev_attr_in1_input.dev_attr.attr, &sensor_dev_attr_in1_min.dev_attr.attr, &sensor_dev_attr_in1_max.dev_attr.attr, + &sensor_dev_attr_in1_alarm.dev_attr.attr, NULL }, { &sensor_dev_attr_in2_input.dev_attr.attr, &sensor_dev_attr_in2_min.dev_attr.attr, &sensor_dev_attr_in2_max.dev_attr.attr, + &sensor_dev_attr_in2_alarm.dev_attr.attr, NULL }, { &sensor_dev_attr_in3_input.dev_attr.attr, &sensor_dev_attr_in3_min.dev_attr.attr, &sensor_dev_attr_in3_max.dev_attr.attr, + &sensor_dev_attr_in3_alarm.dev_attr.attr, NULL }, { &sensor_dev_attr_in4_input.dev_attr.attr, &sensor_dev_attr_in4_min.dev_attr.attr, &sensor_dev_attr_in4_max.dev_attr.attr, + &sensor_dev_attr_in4_alarm.dev_attr.attr, NULL }, { &dev_attr_in5_input.attr, &dev_attr_in5_min.attr, &dev_attr_in5_max.attr, + &sensor_dev_attr_in5_alarm.dev_attr.attr, NULL } }; @@ -642,6 +676,8 @@ static struct attribute *vt8231_attributes[] = { &sensor_dev_attr_fan2_min.dev_attr.attr, &sensor_dev_attr_fan1_div.dev_attr.attr, &sensor_dev_attr_fan2_div.dev_attr.attr, + &sensor_dev_attr_fan1_alarm.dev_attr.attr, + &sensor_dev_attr_fan2_alarm.dev_attr.attr, &dev_attr_alarms.attr, &dev_attr_name.attr, NULL @@ -963,7 +999,7 @@ static void __exit sm_vt8231_exit(void) } } -MODULE_AUTHOR("Roger Lucas <roger@planbit.co.uk>"); +MODULE_AUTHOR("Roger Lucas <vt8231@hiddenengine.co.uk>"); MODULE_DESCRIPTION("VT8231 sensors"); MODULE_LICENSE("GPL"); diff --git a/drivers/hwmon/w83781d.c b/drivers/hwmon/w83781d.c index 7421f6ea53e..5c85670e2d1 100644 --- a/drivers/hwmon/w83781d.c +++ b/drivers/hwmon/w83781d.c @@ -53,8 +53,8 @@ static struct platform_device *pdev; /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d, - 0x2e, 0x2f, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d, + 0x2e, 0x2f, I2C_CLIENT_END }; static unsigned short isa_address = 0x290; /* Insmod parameters */ diff --git a/drivers/hwmon/w83791d.c b/drivers/hwmon/w83791d.c index 85bd21ee329..85077c4c803 100644 --- a/drivers/hwmon/w83791d.c +++ b/drivers/hwmon/w83791d.c @@ -47,7 +47,8 @@ #define NUMBER_OF_TEMPIN 3 /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, + I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(w83791d); diff --git a/drivers/hwmon/w83792d.c b/drivers/hwmon/w83792d.c index 007449d3e16..299629d47ed 100644 --- a/drivers/hwmon/w83792d.c +++ b/drivers/hwmon/w83792d.c @@ -46,7 +46,8 @@ #include <linux/sysfs.h> /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, + I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(w83792d); diff --git a/drivers/hwmon/w83793.c b/drivers/hwmon/w83793.c index 3ba1d6b3347..ee35af93b57 100644 --- a/drivers/hwmon/w83793.c +++ b/drivers/hwmon/w83793.c @@ -37,7 +37,8 @@ #include <linux/mutex.h> /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, + I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(w83793); diff --git a/drivers/hwmon/w83l785ts.c b/drivers/hwmon/w83l785ts.c index 1d6259d29e7..77f2d482888 100644 --- a/drivers/hwmon/w83l785ts.c +++ b/drivers/hwmon/w83l785ts.c @@ -49,7 +49,7 @@ * Address is fully defined internally and cannot be changed. */ -static unsigned short normal_i2c[] = { 0x2e, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2e, I2C_CLIENT_END }; /* * Insmod parameters diff --git a/drivers/hwmon/w83l786ng.c b/drivers/hwmon/w83l786ng.c index 1dbee4fa23a..41e22ddb568 100644 --- a/drivers/hwmon/w83l786ng.c +++ b/drivers/hwmon/w83l786ng.c @@ -35,7 +35,7 @@ #include <linux/mutex.h> /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x2e, 0x2f, I2C_CLIENT_END }; +static const unsigned short normal_i2c[] = { 0x2e, 0x2f, I2C_CLIENT_END }; /* Insmod parameters */ I2C_CLIENT_INSMOD_1(w83l786ng); |