move frv docs one level up

My first guess for "fujitsu" was it might be related to the
fujitsu-laptop.c driver...

Move the frv directory one level up since frv is the name of the
architecture in the Linux kernel.

Signed-off-by: Adrian Bunk <bunk@kernel.org>

1 files changed, 0 insertions, 181 deletions

diff --git a/Documentation/fujitsu/frv/booting.txt b/Documentation/fujitsu/frv/booting.txt
deleted file mode 100644
index 4e229056ef2..00000000000
--- a/Documentation/fujitsu/frv/booting.txt
+++ /dev/null
@@ -1,181 +0,0 @@
-			  =========================
-			  BOOTING FR-V LINUX KERNEL
-			  =========================
-
-======================
-PROVIDING A FILESYSTEM
-======================
-
-First of all, a root filesystem must be made available. This can be done in
-one of two ways:
-
-  (1) NFS Export
-
-      A filesystem should be constructed in a directory on an NFS server that
-      the target board can reach. This directory should then be NFS exported
-      such that the target board can read and write into it as root.
-
-  (2) Flash Filesystem (JFFS2 Recommended)
-
-      In this case, the image must be stored or built up on flash before it
-      can be used. A complete image can be built using the mkfs.jffs2 or
-      similar program and then downloaded and stored into flash by RedBoot.
-
-
-========================
-LOADING THE KERNEL IMAGE
-========================
-
-The kernel will need to be loaded into RAM by RedBoot (or by some alternative
-boot loader) before it can be run. The kernel image (arch/frv/boot/Image) may
-be loaded in one of three ways:
-
-  (1) Load from Flash
-
-      This is the simplest. RedBoot can store an image in the flash (see the
-      RedBoot documentation) and then load it back into RAM. RedBoot keeps
-      track of the load address, entry point and size, so the command to do
-      this is simply:
-
-	fis load linux
-
-      The image is then ready to be executed.
-
-  (2) Load by TFTP
-
-      The following command will download a raw binary kernel image from the
-      default server (as negotiated by BOOTP) and store it into RAM:
-
-	load -b 0x00100000 -r /tftpboot/image.bin
-
-      The image is then ready to be executed.
-
-  (3) Load by Y-Modem
-
-      The following command will download a raw binary kernel image across the
-      serial port that RedBoot is currently using:
-
-	load -m ymodem -b 0x00100000 -r zImage
-
-      The serial client (such as minicom) must then be told to transmit the
-      program by Y-Modem.
-
-      When finished, the image will then be ready to be executed.
-
-
-==================
-BOOTING THE KERNEL
-==================
-
-Boot the image with the following RedBoot command:
-
-	exec -c "<CMDLINE>" 0x00100000
-
-For example:
-
-	exec -c "console=ttySM0,115200 ip=:::::dhcp root=/dev/mtdblock2 rw"
-
-This will start the kernel running. Note that if the GDB-stub is compiled in,
-then the kernel will immediately wait for GDB to connect over serial before
-doing anything else. See the section on kernel debugging with GDB.
-
-The kernel command line <CMDLINE> tells the kernel where its console is and
-how to find its root filesystem. This is made up of the following components,
-separated by spaces:
-
-  (*) console=ttyS<x>[,<baud>[<parity>[<bits>[<flow>]]]]
-
-      This specifies that the system console should output through on-chip
-      serial port <x> (which can be "0" or "1").
-
-      <baud> is a standard baud rate between 1200 and 115200 (default 9600).
-
-      <parity> is a parity setting of "N", "O", "E", "M" or "S" for None, Odd,
-      Even, Mark or Space. "None" is the default.
-
-      <stop> is "7" or "8" for the number of bits per character. "8" is the
-      default.
-
-      <flow> is "r" to use flow control (XCTS on serial port 2 only). The
-      default is to not use flow control.
-
-      For example:
-
-	console=ttyS0,115200
-
-      To use the first on-chip serial port at baud rate 115200, no parity, 8
-      bits, and no flow control.
-
-  (*) root=/dev/<xxxx>
-
-      This specifies the device upon which the root filesystem resides. For
-      example:
-
-	/dev/nfs	NFS root filesystem
-	/dev/mtdblock3	Fourth RedBoot partition on the System Flash
-
-  (*) rw
-
-      Start with the root filesystem mounted Read/Write.
-
-  The remaining components are all optional:
-
-  (*) ip=<ip>::::<host>:<iface>:<cfg>
-
-      Configure the network interface. If <cfg> is "off" then <ip> should
-      specify the IP address for the network device <iface>. <host> provide
-      the hostname for the device.
-
-      If <cfg> is "bootp" or "dhcp", then all of these parameters will be
-      discovered by consulting a BOOTP or DHCP server.
-
-      For example, the following might be used:
-
-	ip=192.168.73.12::::frv:eth0:off
-
-      This sets the IP address on the VDK motherboard RTL8029 ethernet chipset
-      (eth0) to be 192.168.73.12, and sets the board's hostname to be "frv".
-
-  (*) nfsroot=<server>:<dir>[,v<vers>]
-
-      This is mandatory if "root=/dev/nfs" is given as an option. It tells the
-      kernel the IP address of the NFS server providing its root filesystem,
-      and the pathname on that server of the filesystem.
-
-      The NFS version to use can also be specified. v2 and v3 are supported by
-      Linux.
-
-      For example:
-
-	nfsroot=192.168.73.1:/nfsroot-frv
-
-  (*) profile=1
-
-      Turns on the kernel profiler (accessible through /proc/profile).
-
-  (*) console=gdb0
-
-      This can be used as an alternative to the "console=ttyS..." listed
-      above. I tells the kernel to pass the console output to GDB if the
-      gdbstub is compiled in to the kernel.
-
-      If this is used, then the gdbstub passes the text to GDB, which then
-      simply dumps it to its standard output.
-
-  (*) mem=<xxx>M
-
-      Normally the kernel will work out how much SDRAM it has by reading the
-      SDRAM controller registers. That can be overridden with this
-      option. This allows the kernel to be told that it has <xxx> megabytes of
-      memory available.
-
-  (*) init=<prog> [<arg> [<arg> [<arg> ...]]]
-
-      This tells the kernel what program to run initially. By default this is
-      /sbin/init, but /sbin/sash or /bin/sh are common alternatives.
-
-  (*) vdc=...
-
-      This option configures the MB93493 companion chip visual display
-      driver. Please see Documentation/fujitsu/mb93493/vdc.txt for more
-      information.