| Age | Commit message (Collapse) | Author |
|---|
|
DRM_FORMAT_RGB888 is 24 bits per pixel and it would be natural to send it
on the SPI bus using a 24 bits per word transfer. The problem with this
is that not all SPI controllers support 24 bpw.
Since DRM_FORMAT_RGB888 is stored in memory as little endian and the SPI
bus is big endian we use 8 bpw to always get the same pixel format on the
bus: b8g8r8.
The MIPI DCS specification lists the standard commands that can be sent
over the MIPI DBI interface. The set_address_mode (36h) command has one
bit in the parameter that controls RGB/BGR order. This means that the
controller can be configured to receive the pixel as BGR.
RGB888 is rarely supported on these controllers but RGB666 is very common.
All datasheets I have seen do at least support the pixel format option
where each color is sent as one byte and the 6 MSB's are used.
All this put together means that we can send each pixel as b8g8r8 and an
RGB666 capable controller sees this as b6x2g6x2r6x2.
v4:
- s/emulation_format/pixel_format/ (Dmitry)
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240604-panel-mipi-dbi-rgb666-v4-4-d7c2bcb9b78d@tronnes.org
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
|
|
MIPI DCS write/set commands have 8 bit parameters except for the
write_memory commands where it depends on the pixel format.
drm_mipi_dbi does currently only support RGB565 which is 16-bit and it
has to make sure that the pixels enters the SPI bus in big endian format
since the MIPI DBI spec doesn't have support for little endian.
drm_mipi_dbi is optimized for DBI interface option 3 which means that the
16-bit bytes are swapped by the upper layer if the SPI bus does not
support 16 bits per word, signified by the swap_bytes member.
In order to support both 16-bit and 24-bit pixel transfers we need a way
to tell the DBI command layer the format of the buffer. Add a
write_memory_bpw member that the upper layer can use to tell how many
bits per word to use for the SPI transfer.
v4:
- Expand the commit message (Dmitry)
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240604-panel-mipi-dbi-rgb666-v4-3-d7c2bcb9b78d@tronnes.org
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
|
|
Pass an instance of struct drm_format_conv_state to DRM's format
conversion helpers. Update all callers.
Most drivers can use the format-conversion state from their shadow-
plane state. The shadow plane's destroy function releases the
allocated buffer. Drivers will later be able to allocate a buffer
of appropriate size in their plane's atomic_check code.
The gud driver uses a separate thread for committing updates. For
now, the update worker contains its own format-conversion state.
Images in the format-helper tests are small. The tests preallocate
a static page for the temporary buffer. Unloading the module releases
the memory.
v6:
* update patch for ssd132x support
v5:
* avoid using unusupported shadow-plane state in repaper (Noralf)
* fix documentation (Noralf, kernel test robot)
v3:
* store buffer in shadow-plane state (Javier, Maxime)
* replace ARRAY_SIZE() with sizeof() (Jani)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Javier Martinez Canillas <javierm@redhat.com> # ssd130x
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009141018.11291-4-tzimmermann@suse.de
|
|
The MIPI DBI specification defines separate vdd (panel power) and
vddi (I/O voltage) supplies. Displays that require different voltages
for the different supplies do exist, so the supplies cannot be
combined into one as they are now. Add a new io_regulator property to
the mipi_dbi_dev struct which can be set by the panel driver along
with the regulator property.
Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221201160245.2093816-2-otto.pflueger@abscue.de
|
|
Implement MIPI DBI planes with struct drm_shadow_plane_state, so that the
respective drivers can use the vmap'ed GEM-buffer memory. Implement state
helpers, the {begin,end}_fb_access helpers and wire up everything.
With this commit, MIPI DBI drivers can access the GEM object's memory
that is provided by shadow-plane state. The actual changes to drivers
are implemented separately.
v2:
* use shadow-plane state directly (Noralf)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org> # drm/tiny/mi0283qt
Link: https://patchwork.freedesktop.org/patch/msgid/20221202125644.7917-7-tzimmermann@suse.de
|
|
Move the vmap/vunmap blocks from the inner fb_dirty helpers into the
MIPI DBI update helpers. The function calls can result in waiting and/or
processing overhead. Reduce the penalties by executing the functions once
in the outer-most function of the pipe update.
This change also prepares for MIPI DBI for shadow-plane helpers. With
shadow-plane helpers, transfer source buffers are mapped into kernel
address space automatically.
v2:
* keep each driver's existing buffer-mapping patter (Noralf)
* zero-initialize iosys_map arrays (Noralf)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org> # drm/tiny/mi0283qt
Link: https://patchwork.freedesktop.org/patch/msgid/20221202125644.7917-6-tzimmermann@suse.de
|
|
Introduce DRM_MIPI_DBI_SIMPLE_DISPLAY_PIPE_FUNCS to initialize MIPI-DBI
helpers to default values and convert drivers. The prepare_fb function
set by some drivers is called implicitly by simple-kms helpers, so leave
it out.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org> # drm/tiny/mi0283qt
Link: https://patchwork.freedesktop.org/patch/msgid/20221202125644.7917-5-tzimmermann@suse.de
|
|
Add drm_crtc_helper_mode_valid_fixed(), which validates a given mode
against a display hardware's mode. Convert simpledrm and use it in a
few other drivers with static modes.
v4:
* remove empty line after opening brace
v2:
* rename 'static' and 'hw' to 'fixed' everywhere
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905141648.22013-3-tzimmermann@suse.de
|
|
devm_drm_dev_alloc() can't allocate structures that embed a structure
which then again embeds drm_device. Workaround this by adding a
driver_private pointer to struct mipi_dbi_dev which the driver can use for
its additional state.
v3:
- Add documentation
Acked-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-5-noralf@tronnes.org
|
|
Replace the slightly odd "#define <function> NULL" thing with
a standard static inline stub.
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211221193754.12287-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
The macro mipi_dbi_command() does not report errors unless you wrap it
in another macro to do the error reporting.
Report a rate-limited error so we know what is going on.
After this any code wishing to send command arrays can rely on
mipi_dbi_command() providing an appropriate error message if something
goes wrong.
Suggested-by: Noralf Trønnes <noralf@tronnes.org>
Suggested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210702135601.3952726-1-linus.walleij@linaro.org
|
|
The syntax without dots is available since commit 43756e347f21
("scripts/kernel-doc: Add support for named variable macro arguments").
The same HTML output is produced with and without this patch.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210101211818.1023919-1-j.neuschaefer@gmx.net
|
|
The atomic helpers try really hard to not lose track of things,
duplicating enabled tracking in the driver is at best confusing.
Double-enabling or disabling is a bug in atomic helpers.
In the fb_dirty function we can just assume that the fb always exists,
simple display pipe helpers guarantee that the crtc is only enabled
together with the output, so we always have a primary plane around.
Now in the update function we need to be a notch more careful, since
that can also get called when the crtc is off. And we don't want to
upload frames when that's the case, so filter that out too.
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: David Lechner <david@lechnology.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612160056.2082681-7-daniel.vetter@ffwll.ch
|
|
Allows us to drop the drm_driver.release callback from all
drivers, and remove the mipi_dbi_release() function.
This is made possible by a preceeding patch which added a drmm_
cleanup action to drm_mode_config_init(), hence all we need to do to
ensure that drm_mode_config_cleanup() is run on final drm_device
cleanup is check the new error code for _init().
v2: Explain why this cleanup is possible (Laurent).
v3: Use drmm_mode_config_init() for more clarity (Sam, Thomas)
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org> (v2)
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Eric Anholt <eric@anholt.net>
Cc: David Lechner <david@lechnology.com>
Cc: Kamlesh Gurudasani <kamlesh.gurudasani@gmail.com>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200323144950.3018436-49-daniel.vetter@ffwll.ch
|
|
mipi_dbi_command_stackbuf() copies the passed buffer data, so it can be
const.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316164249.6234-1-geert+renesas@glider.be
|
|
As a result of commit 987d65d01356 (drm: debugfs: make
drm_debugfs_create_files() never fail) and changes to various debugfs
functions in drm/core and across various drivers, there is no need for
the drm_driver.debugfs_init() hook to have a return value. Therefore,
declare it as void.
This also includes refactoring all users of the .debugfs_init() hook to
return void across the subsystem.
v2: include changes to the hook and drivers that use it in one patch to
prevent driver breakage and enable individual successful compilation of
this change.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-18-wambui.karugax@gmail.com
|
|
If the resolution of the TFT display is smaller than the maximum
resolution supported by the display controller, the display may be
connected to the driver output arrays with a horizontal and/or vertical
offset, leading to a shifted image.
Add support for specifying these offsets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200115124548.3951-4-geert+renesas@glider.be
|
|
This moves mipi-dbi to be a core helper with the name drm_mipi_dbi.
Fixup include's in drivers.
Move the docs entry and delete tinydrm.rst.
Delete the last tinydrm todo entry.
v2: Make DRM_MIPI_DBI tristate to enable it being built as a module.
Cc: Eric Anholt <eric@anholt.net>
Cc: David Lechner <david@lechnology.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: David Lechner <david@lechnology.com>
Acked-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190722104312.16184-9-noralf@tronnes.org
|
