| Age | Commit message (Collapse) | Author |
|---|
|
The current power direction of an USB-C port also influences the
power_supply's online status, so a power role change should also update
the power_supply.
Fixes an issue on some systems where plugging in a normal USB device in
for the first time after a reboot will cause upower to erroneously
consider the system to be connected to AC power.
Cc: stable <stable@kernel.org>
Fixes: 0e6371fbfba3 ("usb: typec: ucsi: Report power supply changes")
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250721-fix-ucsi-pwr-dir-notify-v1-1-e53d5340cb38@qtmlabs.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ucsi_psy_get_current_max would return 0mA as the maximum current if
UCSI detected a BC or a Default USB Power sporce.
The comment in this function is true that we can't tell the difference
between DCP/CDP or SDP chargers, but we can guarantee that at least 1-unit
of USB 1.1/2.0 power is available, which is 100mA, which is a better
fallback value than 0, which causes some userspaces, including the ChromeOS
power manager, to regard this as a power source that is not providing
any power.
In reality, 100mA is guaranteed from all sources in these classes.
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Jameson Thies <jthies@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250717200805.3710473-1-bleung@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes a race condition communication error, which ends up in
PD hard resets when losing the race. Some systems, like the Radxa ROCK
5B are powered through USB-C without any backup power source and use a
FUSB302 chip to do the PD negotiation. This means it is quite important
to avoid hard resets, since that effectively kills the system's
power-supply.
I've found the following race condition while debugging unplanned power
loss during booting the board every now and then:
1. lots of TCPM/FUSB302/PD initialization stuff
2. TCPM ends up in SNK_WAIT_CAPABILITIES (tcpm_set_pd_rx is enabled here)
3. the remote PD source does not send anything, so TCPM does a SOFT RESET
4. TCPM ends up in SNK_WAIT_CAPABILITIES for the second time
(tcpm_set_pd_rx is enabled again, even though it is still on)
At this point I've seen broken CRC good messages being send by the
FUSB302 with a logic analyzer sniffing the CC lines. Also it looks like
messages are being lost and things generally going haywire with one of
the two sides doing a hard reset once a broken CRC good message was send
to the bus.
I think the system is running into a race condition, that the FIFOs are
being cleared and/or the automatic good CRC message generation flag is
being updated while a message is already arriving.
Let's avoid this by caching the PD RX enabled state, as we have already
processed anything in the FIFOs and are in a good state. As a side
effect that this also optimizes I2C bus usage :)
As far as I can tell the problem theoretically also exists when TCPM
enters SNK_WAIT_CAPABILITIES the first time, but I believe this is less
critical for the following reason:
On devices like the ROCK 5B, which are powered through a TCPM backed
USB-C port, the bootloader must have done some prior PD communication
(initial communication must happen within 5 seconds after plugging the
USB-C plug). This means the first time the kernel TCPM state machine
reaches SNK_WAIT_CAPABILITIES, the remote side is not sending messages
actively. On other devices a hard reset simply adds some extra delay and
things should be good afterwards.
Fixes: c034a43e72dda ("staging: typec: Fairchild FUSB302 Type-c chip driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250704-fusb302-race-condition-fix-v1-1-239012c0e27a@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Selecting DRM_AUX_HPD_BRIDGE is not possible from a built-in driver when
CONFIG_DRM=m:
WARNING: unmet direct dependencies detected for DRM_AUX_HPD_BRIDGE
Depends on [m]: HAS_IOMEM [=y] && DRM [=m] && DRM_BRIDGE [=y] && OF [=y]
Selected by [y]:
- UCSI_LENOVO_YOGA_C630 [=y] && USB_SUPPORT [=y] && TYPEC [=y] && TYPEC_UCSI [=y] && EC_LENOVO_YOGA_C630 [=y] && DRM_BRIDGE [=y] && OF [=y]
arm-linux-gnueabi-ld: drivers/gpu/drm/bridge/aux-hpd-bridge.o: in function `drm_aux_hpd_bridge_notify':
aux-hpd-bridge.c:(.text.drm_aux_hpd_bridge_notify+0x28): undefined reference to `drm_bridge_hpd_notify'
arm-linux-gnueabi-ld: drivers/gpu/drm/bridge/aux-hpd-bridge.o: in function `drm_aux_hpd_bridge_probe':
aux-hpd-bridge.c:(.text.drm_aux_hpd_bridge_probe+0x20): undefined reference to `__devm_drm_bridge_alloc'
Add a dependency to force UCSI_LENOVO_YOGA_C630 to be a loadable module as
well in this configuration.
Fixes: eb90d36bfa06 ("usb: typec: ucsi: yoga-c630: register DRM HPD bridge")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250717133045.991254-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cros_ec_ucsi fails to allocate a UCSI instance in it's probe function
because it does not define all operations checked by ucsi_create.
Update cros_ec_ucsi operations to use the same function for read_cci
and poll_cci.
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20250711202033.2201305-1-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver works fine with asynchronous probe.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250707-max77759-irq-wake-v1-3-d367f633e4bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The general recommendation is to not use of_match_ptr() or CONFIG_OF
ifdef.
Drop them.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250707-max77759-irq-wake-v1-2-d367f633e4bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver calls enable_irq_wake() during probe() unconditionally, and
never issues the required corresponding disable_irq_wake() to disable
hardware interrupt wakeup signals.
Additionally, whether or not a device should wake-up the system is
meant to be a policy decision based on sysfs (.../power/wakeup) in the
first place.
Update the driver to use the standard approach to enable/disable IRQ
wake during the suspend/resume callbacks. This solves both issues
described above.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250707-max77759-irq-wake-v1-1-d367f633e4bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well to build on top of for other
changes that depend on them.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The deadlock can occur due to a recursive lock acquisition of
`cros_typec_altmode_data::mutex`.
The call chain is as follows:
1. cros_typec_altmode_work() acquires the mutex
2. typec_altmode_vdm() -> dp_altmode_vdm() ->
3. typec_altmode_exit() -> cros_typec_altmode_exit()
4. cros_typec_altmode_exit() attempts to acquire the mutex again
To prevent this, defer the `typec_altmode_exit()` call by scheduling
it rather than calling it directly from within the mutex-protected
context.
Cc: stable <stable@kernel.org>
Fixes: b4b38ffb38c9 ("usb: typec: displayport: Receive DP Status Update NAK request exit dp altmode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250624133246.3936737-1-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A poorly implemented DisplayPort Alt Mode port partner can indicate
that its pin assignment capabilities are greater than the maximum
value, DP_PIN_ASSIGN_F. In this case, calls to pin_assignment_show
will cause a BRK exception due to an out of bounds array access.
Prevent for loop in pin_assignment_show from accessing
invalid values in pin_assignments by adding DP_PIN_ASSIGN_MAX
value in typec_dp.h and using i < DP_PIN_ASSIGN_MAX as a loop
condition.
Fixes: 0e3bb7d6894d ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250618224943.3263103-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes Type-C compliance test TD 4.7.6 - Try.SNK DRP Connect
SNKAS.
tVbusON has a limit of 275ms when entering SRC_ATTACHED. Compliance
testers can interpret the TryWait.Src to Attached.Src transition after
Try.Snk as being in Attached.Src the entire time, so ~170ms is lost
to the debounce timer.
Setting the data role can be a costly operation in host mode, and when
completed after 100ms can cause Type-C compliance test check TD 4.7.5.V.4
to fail.
Turn VBUS on before tcpm_set_roles to meet timing requirement.
Fixes: f0690a25a140 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250618230606.3272497-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On Qualcomm platforms DisplayPort driver expects to have a drm bridge in
the final device on the USB-C chain. Register the DRM HPD bridge in
order to fulfill this requirement and to send HPD events to the DRM
driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250621-c630-ucsi-v1-8-a86de5e11361@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Parse USB / HPD messages from EC in order to set the orientation of the
corresponding Type-C port, letting connected USB 3 devices to enjoy
SuperSpeed connection rather than beign limited to HighSpeed only (if
the orientation didn't match).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250621-c630-ucsi-v1-7-a86de5e11361@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On Lenovo Yoga C630 the EC handles GET_CURRENT_CAM command, but it
returns 1 if DisplayPort is active and 0 otherwise. However in order to
let UCSI drivers handle AltModes correctly, it should return 0 / 0xff.
Correct returned value.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250621-c630-ucsi-v1-6-a86de5e11361@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
EC firmware provides information about partner AltModes and handles the
DisplayPort AltMode internally, however it doesn't report AltModes of
the port to the host. Fake the DP AltMode for port0 in order to let
Linux bind displayport AltMode driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250621-c630-ucsi-v1-5-a86de5e11361@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On Lenovo Yoga C630 the EC firmware is buggy and it cat return altmodes
for a device pushed into the port 0 (right) when the driver asks for
altmodes for port 1 (left). Since the left Type-C port doesn't support
DP anyway, ignore all UCSI_GET_ALTERNATE_MODES commands destined to the
port 1.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250621-c630-ucsi-v1-4-a86de5e11361@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On Lenovo Yoga C630 the EC firmware is buggy and it returns duplicate
AltModes over and over again instead of returning an empty one, as
demanded by the spec. Ignore extra altmodes by zeroing them in the
update_altmodes() callback. It is not possible to shortcut that in the
sync_control() callback since we need to know if the AltMode matches the
first reported AltMode or not.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250621-c630-ucsi-v1-3-a86de5e11361@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The update_altmodes() is executed only for connetor's AltModes, because
that's what required on the CCG platforms. Other platforms (like Lenovo
Yoga C630) requires similar fix for partner's AltModes. Extend
update_altmodes() callback to accept the recipient as an argument and
move corresponding check to the CCG UCSI driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250621-c630-ucsi-v1-2-a86de5e11361@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix memory leak and call ucsi_destroy() from the driver's remove
function and probe's error path in order to remove debugfs files and
free the memory. Also call yoga_c630_ec_unregister_notify() in the
probe's error path.
Fixes: 2ea6d07efe53 ("usb: typec: ucsi: add Lenovo Yoga C630 glue driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250621-c630-ucsi-v1-1-a86de5e11361@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add irq_hpd sysfs node to displayport driver. This allows the userspace
to subscribe to irq events similar to how it can subscribe to changes in
hpd.
irq_hpd is read only and returns the number of irq events generated since
driver probe. pending_irq_hpd is added so that a sysfs_emit can be
generated if the HPD high event belonging to the same status message
is delayed until a successful configuration.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250623204947.732915-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If pmc_usb_probe is called before SCU IPC is registered, pmc_usb_probe
will fail.
Return -EPROBE_DEFER when pmc_usb_probe doesn't get SCU IPC device, so
the probe function can be called again after SCU IPC is initialized.
Signed-off-by: Tomasz Michalec <tmichalec@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250610154058.1859812-1-tmichalec@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ucsi_cci_str() last use was removed in 2019 by
commit 2ede55468ca8 ("usb: typec: ucsi: Remove the old API")
Remove it.
Signed-off-by: "Dr. David Alan Gilbert" <linux@treblig.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250609004319.209143-1-linux@treblig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the gpio irqchip connected to a slow bus(e.g., i2c bus or virtio
bus), calling disable_irq_nosync() in top-half ISR handler will trigger
the following kernel BUG:
BUG: scheduling while atomic: RenderEngine/253/0x00010002
...
Call trace:
dump_backtrace+0x0/0x1c8
show_stack+0x1c/0x2c
dump_stack_lvl+0xdc/0x12c
dump_stack+0x1c/0x64
__schedule_bug+0x64/0x80
schedule_debug+0x98/0x118
__schedule+0x68/0x704
schedule+0xa0/0xe8
schedule_timeout+0x38/0x124
wait_for_common+0xa4/0x134
wait_for_completion+0x1c/0x2c
_virtio_gpio_req+0xf8/0x198
virtio_gpio_irq_bus_sync_unlock+0x94/0xf0
__irq_put_desc_unlock+0x50/0x54
disable_irq_nosync+0x64/0x94
fusb302_irq_intn+0x24/0x84
__handle_irq_event_percpu+0x84/0x278
handle_irq_event+0x64/0x14c
handle_level_irq+0x134/0x1d4
generic_handle_domain_irq+0x40/0x68
virtio_gpio_event_vq+0xb0/0x130
vring_interrupt+0x7c/0x90
vm_interrupt+0x88/0xd8
__handle_irq_event_percpu+0x84/0x278
handle_irq_event+0x64/0x14c
handle_fasteoi_irq+0x110/0x210
__handle_domain_irq+0x80/0xd0
gic_handle_irq+0x78/0x154
el0_irq_naked+0x60/0x6c
This patch replaces request_irq() with devm_request_threaded_irq() to
avoid the use of disable_irq_nosync().
Signed-off-by: Yongbo Zhang <giraffesnn123@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250526043433.673097-1-giraffesnn123@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.16-rc1.
Included in here are the following:
- USB offload support for audio devices.
I think this takes the record for the most number of patch series
(30+) over the longest period of time (2+ years) to get merged
properly.
Many props go to Wesley Cheng for seeing this effort through, they
took a major out-of-tree hacked-up-monstrosity that was created by
multiple vendors for their specific devices, got it all merged into
a semi-coherent set of changes, and got all of the different major
subsystems to agree on how this should be implemented both with
changes to their code as well as userspace apis, AND wrangled the
hardware companies into agreeing to go forward with this, despite
making them all redo work they had already done in their private
device trees.
This feature offers major power savings on embedded devices where a
USB audio stream can continue to flow while the rest of the system
is sleeping, something that devices running on battery power really
care about. There are still some more small tweaks left to be done
here, and those patches are still out for review and arguing among
the different hardware companies, but this is a major step forward
and a great example of how to do upstream development well.
- small number of thunderbolt fixes and updates, things seem to be
slowing down here (famous last words...)
- xhci refactors and reworking to try to handle some rough corner
cases in some hardware implementations where things don't always
work properly
- typec driver updates
- USB3 power management reworking and updates
- Removal of some old and orphaned UDC gadget drivers that had not
been used in a very long time, dropping over 11 thousand lines from
the tree, always a nice thing, making up for the 12k lines added
for the USB offload feature.
- lots of little updates and fixes in different drivers
All of these have been in linux-next for over 2 weeks, the USB offload
logic has been in there for 8 weeks now, with no reported issues"
* tag 'usb-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (172 commits)
ALSA: usb-audio: qcom: fix USB_XHCI dependency
ASoC: qdsp6: fix compile-testing without CONFIG_OF
usb: misc: onboard_usb_dev: fix build warning for CONFIG_USB_ONBOARD_DEV_USB5744=n
usb: typec: tipd: fix typo in TPS_STATUS_HIGH_VOLAGE_WARNING macro
USB: typec: fix const issue in typec_match()
USB: gadget: udc: fix const issue in gadget_match_driver()
USB: gadget: fix up const issue with struct usb_function_instance
USB: serial: pl2303: add new chip PL2303GC-Q20 and PL2303GT-2AB
USB: serial: bus: fix const issue in usb_serial_device_match()
usb: usbtmc: Fix timeout value in get_stb
usb: usbtmc: Fix read_stb function and get_stb ioctl
ALSA: qc_audio_offload: try to reduce address space confusion
ALSA: qc_audio_offload: avoid leaking xfer_buf allocation
ALSA: qc_audio_offload: rename dma/iova/va/cpu/phys variables
ALSA: usb-audio: qcom: Fix an error handling path in qc_usb_audio_probe()
usb: misc: onboard_usb_dev: Fix usb5744 initialization sequence
dt-bindings: usb: ti,usb8041: Add binding for TI USB8044 hub controller
usb: misc: onboard_usb_dev: Add support for TI TUSB8044 hub
usb: gadget: lpc32xx_udc: Use USB API functions rather than constants
usb: gadget: epautoconf: Use USB API functions rather than constants
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"LED Triggers:
- Allow writing "default" to the sysfs 'trigger' attribute to set an
LED to its default trigger
- If the default trigger is "none", writing "default" will remove the
current trigger
- Updated sysfs ABI documentation for the new "default" trigger
functionality
LED KUnit Testing:
- Provide a skeleton KUnit test suite for the LEDs framework
- Expand the LED class device registration KUnit test to cover more
scenarios, including 'brightness_get' behavior
- Add KUnit tests for the LED lookup and get API ('led_add_lookup',
'devm_led_get')
LED Flash Class:
- Add support for setting flash/strobe duration through a new
'duration_set' op and 'led_set_flash_duration()' function, aligning
with 'V4L2_CID_FLASH_DURATION'
Texas Instruments TPS6131x:
- Add a new driver for the TPS61310/TPS61311 flash LED controllers
- The driver supports the device's three constant-current sinks for
flash and torch modes
LED Core:
- Prevent potential 'snprintf()' truncations in LED names by checking
for buffer overflows
ChromeOS EC LEDs:
- Avoid a -Wflex-array-member-not-at-end GCC warning by replacing an
on-stack flexible structure definition with a utility function call
Multicolor LEDs:
- Fix issue where setting multi_intensity while software blinking is
active could stop blinking
PCA955x LEDs:
- Avoid potential buffer overflow when creating default labels by
changing a field's type to 'u8' and updating format specifiers
PCA995x LEDs:
- Fix a typo (stray space) in an 'of_device_id' entry in the
'pca995x_of_match' table
Kconfig:
- Prevent LED drivers from being enabled by default when
'COMPILE_TEST' is set
Device Property API:
- Split 'device_get_child_node_count()' into a new helper
'fwnode_get_child_node_count()' that doesn't require a device
struct, making the API more symmetrical
Driver Modernization (using 'fwnode_get_child_node_count()'):
- Update 'leds-pwm-multicolor', 'leds-ncp5623' and 'leds-ncp5623' to
use the new 'fwnode_get_child_node_count()' helper, removing their
custom implementation
- As above in the USB Type-C TCPM driver
Driver Modernization (using new GPIO setter callbacks):
- Convert 'leds-lgm-sso' to use new GPIO line value setter callbacks
which return an integer for error handling
- Convert 'leds-pca955x', 'leds-pca9532' and 'leds-tca6507' to use
new GPIO setter callbacks
Documentation:
- Remove the '.rst' extension for 'leds-st1202' in the documentation
index for consistency
LP8860 LEDs:
- Use 'regmap_multi_reg_write()' for EEPROM writes instead of manual
looping
- Use scoped mutex guards and 'devm_mutex_init()' to simplify
function exits and ensure automatic cleanup
- Remove default register definitions that are unused when regmap
caching is not active
- Use 'devm_regulator_get_enable_optional()' to handle the optional
regulator, simplifying enabling and removing manual disabling
- Refactor 'lp8860_unlock_eeprom()' to only perform the unlock
operation, removing the lock part and an unnecessary parameter
- Use a 'devm' action to disable the enable-GPIO, simplifying cleanup
and error paths, and remove the now-empty '.remove()' function
Turris Omnia LEDs:
- Drop unnecessary commas in terminator entries of 'struct attribute'
and 'struct of_device_id' arrays
MT6370 RGB LEDs:
- Use the 'LINEAR_RANGE()' for defining 'struct linear_range' entries
to improve robustness
Texas Instruments TPS6131x:
- Add new devicetree bindings for the TI TPS61310/TPS61311 flash LED
driver"
* tag 'leds-next-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (31 commits)
leds: tps6131x: Add support for Texas Instruments TPS6131X flash LED driver
dt-bindings: leds: Add Texas Instruments TPS6131x flash LED driver
leds: flash: Add support for flash/strobe duration
leds: rgb: leds-mt6370-rgb: Improve definition of some struct linear_range
leds: led-test: Provide tests for the lookup and get infrastructure
leds: led-test: Fill out the registration test to cover more test cases
leds: led-test: Remove standard error checking after KUNIT_ASSERT_*()
leds: pca995x: Fix typo in pca995x_of_match's of_device_id entry
leds: Provide skeleton KUnit testing for the LEDs framework
leds: tca6507: Use new GPIO line value setter callbacks
leds: pca9532: Use new GPIO line value setter callbacks
leds: pca955x: Use new GPIO line value setter callbacks
leds: lgm-sso: Use new GPIO line value setter callbacks
leds: Do not enable by default during compile testing
leds: turris-omnia: Drop commas in the terminator entries
leds: lp8860: Disable GPIO with devm action
leds: lp8860: Only unlock in lp8860_unlock_eeprom()
leds: lp8860: Enable regulator using enable_optional helper
leds: lp8860: Remove default regs when not caching
leds: lp8860: Use new mutex guards to cleanup function exits
...
|
|
Merge updates related to system sleep handling and runtime PM for 6.16-rc1:
- Fix denying of auto suspend in pm_suspend_timer_fn() (Charan Teja
Kalla).
- Move debug runtime PM attributes to runtime_attrs[] (Rafael Wysocki).
- Add new devm_ functions for enabling runtime PM and runtime PM
reference counting (Bence Csókás).
- Remove size arguments from strscpy() calls in the hibernation core
code (Thorsten Blum).
- Adjust the handling of devices with asynchronous suspend enabled
during system suspend and resume to start resuming them immediately
after resuming their parents and to start suspending such a device
immediately after suspending its first child (Rafael Wysocki).
- Adjust messages printed during tasks freezing to avoid using
pr_cont() (Andrew Sayers, Paul Menzel).
- Clean up unnecessary usage of !! in pm_print_times_init() (Zihuan
Zhang).
- Add missing wakeup source attribute relax_count to sysfs and
remove the space character at the end ofi the string produced by
pm_show_wakelocks() (Zijun Hu).
- Add configurable pm_test delay for hibernation (Zihuan Zhang).
- Disable asynchronous suspend in ucsi_ccg_probe() to prevent the
cypd4226 device on Tegra boards from suspending prematurely (Jon
Hunter).
- Unbreak printing PM debug messages during hibernation and clean up
some related code (Rafael Wysocki).
* pm-runtime:
PM: runtime: fix denying of auto suspend in pm_suspend_timer_fn()
PM: sysfs: Move debug runtime PM attributes to runtime_attrs[]
PM: runtime: Add new devm functions
* pm-sleep:
PM: freezer: Rewrite restarting tasks log to remove stray *done.*
PM: sleep: Introduce pm_sleep_transition_in_progress()
PM: sleep: Introduce pm_suspend_in_progress()
PM: sleep: Print PM debug messages during hibernation
ucsi_ccg: Disable async suspend in ucsi_ccg_probe()
PM: hibernate: add configurable delay for pm_test
PM: wakeup: Delete space in the end of string shown by pm_show_wakelocks()
PM: wakeup: Add missing wakeup source attribute relax_count
PM: sleep: Remove unnecessary !!
PM: sleep: Use two lines for "Restarting..." / "done" messages
PM: sleep: Make suspend of devices more asynchronous
PM: sleep: Suspend async parents after suspending children
PM: sleep: Resume children after resuming the parent
PM: hibernate: Remove size arguments when calling strscpy()
|
|
"VOLAGE" should become "VOLTAGE"
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Reviewed-by: Brigham Campbell <me@brighamcampbell.com>
Link: https://lore.kernel.org/r/20250521214851.386796-1-jihed.chaibi.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
typec_match() takes a const pointer, and then decides to cast it away
into a non-const one, which is not a good thing to do overall. Fix this
up by properly setting the pointers to be const to preserve that
attribute.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/2025052126-scholar-stainless-ad55@gregkh
Fixes: d69d80484598 ("driver core: have match() callback in struct bus_type take a const *")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Initialize negotiated_rev and negotiated_rev_prime based on the port's
configured PD revision (rev_major) rather than always defaulting to
PD_MAX_REV. This ensures ports start PD communication using their
appropriate revision level.
This allows proper communication with devices that require specific
PD revision levels, especially for the hardware designed for PD 1.0
or 2.0 specifications.
Signed-off-by: Cosmo Chou <chou.cosmo@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250513130834.1612602-1-chou.cosmo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A state check was previously added to tcpm_queue_vdm_unlocked to
prevent a deadlock where the DisplayPort Alt Mode driver would be
executing work and attempting to grab the tcpm_lock while the TCPM
was holding the lock and attempting to unregister the altmode, blocking
on the altmode driver's cancel_work_sync call.
Because the state check isn't protected, there is a small window
where the Alt Mode driver could determine that the TCPM is
in a ready state and attempt to grab the lock while the
TCPM grabs the lock and changes the TCPM state to one that
causes the deadlock. The callstack is provided below:
[110121.667392][ C7] Call trace:
[110121.667396][ C7] __switch_to+0x174/0x338
[110121.667406][ C7] __schedule+0x608/0x9f0
[110121.667414][ C7] schedule+0x7c/0xe8
[110121.667423][ C7] kernfs_drain+0xb0/0x114
[110121.667431][ C7] __kernfs_remove+0x16c/0x20c
[110121.667436][ C7] kernfs_remove_by_name_ns+0x74/0xe8
[110121.667442][ C7] sysfs_remove_group+0x84/0xe8
[110121.667450][ C7] sysfs_remove_groups+0x34/0x58
[110121.667458][ C7] device_remove_groups+0x10/0x20
[110121.667464][ C7] device_release_driver_internal+0x164/0x2e4
[110121.667475][ C7] device_release_driver+0x18/0x28
[110121.667484][ C7] bus_remove_device+0xec/0x118
[110121.667491][ C7] device_del+0x1e8/0x4ac
[110121.667498][ C7] device_unregister+0x18/0x38
[110121.667504][ C7] typec_unregister_altmode+0x30/0x44
[110121.667515][ C7] tcpm_reset_port+0xac/0x370
[110121.667523][ C7] tcpm_snk_detach+0x84/0xb8
[110121.667529][ C7] run_state_machine+0x4c0/0x1b68
[110121.667536][ C7] tcpm_state_machine_work+0x94/0xe4
[110121.667544][ C7] kthread_worker_fn+0x10c/0x244
[110121.667552][ C7] kthread+0x104/0x1d4
[110121.667557][ C7] ret_from_fork+0x10/0x20
[110121.667689][ C7] Workqueue: events dp_altmode_work
[110121.667697][ C7] Call trace:
[110121.667701][ C7] __switch_to+0x174/0x338
[110121.667710][ C7] __schedule+0x608/0x9f0
[110121.667717][ C7] schedule+0x7c/0xe8
[110121.667725][ C7] schedule_preempt_disabled+0x24/0x40
[110121.667733][ C7] __mutex_lock+0x408/0xdac
[110121.667741][ C7] __mutex_lock_slowpath+0x14/0x24
[110121.667748][ C7] mutex_lock+0x40/0xec
[110121.667757][ C7] tcpm_altmode_enter+0x78/0xb4
[110121.667764][ C7] typec_altmode_enter+0xdc/0x10c
[110121.667769][ C7] dp_altmode_work+0x68/0x164
[110121.667775][ C7] process_one_work+0x1e4/0x43c
[110121.667783][ C7] worker_thread+0x25c/0x430
[110121.667789][ C7] kthread+0x104/0x1d4
[110121.667794][ C7] ret_from_fork+0x10/0x20
Change tcpm_queue_vdm_unlocked to queue for tcpm_queue_vdm_work,
which can perform the state check while holding the TCPM lock
while the Alt Mode lock is no longer held. This requires a new
struct to hold the vdm data, altmode_vdm_event.
Fixes: cdc9946ea637 ("usb: typec: tcpm: enforce ready state when queueing alt mode vdm")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250506232853.1968304-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Register read of TCPC_RX_BYTE_CNT returns the total size consisting of:
PD message (pending read) size + 1 Byte for Frame Type (SOP*)
This is validated against the max PD message (`struct pd_message`) size
without accounting for the extra byte for the frame type. Note that the
struct pd_message does not contain a field for the frame_type. This
results in false negatives when the "PD message (pending read)" is equal
to the max PD message size.
Fixes: 6f413b559f86 ("usb: typec: tcpci_maxim: Chip level TCPC driver")
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Kyle Tso <kyletso@google.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/stable/20250502-b4-new-fix-pd-rx-count-v1-1-e5711ed09b3d%40google.com
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250502-b4-new-fix-pd-rx-count-v1-1-e5711ed09b3d@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.16 merge window
This includes following USB4/Thunderbolt changes for the v6.16 merge
window:
- Enable wake on connect and disconnect over system suspend.
- Add mapping between Type-C ports and USB4 ports on non-Chrome systems.
- Expose tunneling related events to userspace.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.16-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
Documentation/admin-guide: Document Thunderbolt/USB4 tunneling events
thunderbolt: Notify userspace about firmware CM tunneling events
thunderbolt: Notify userspace about software CM tunneling events
thunderbolt: Introduce domain event message handler
usb: typec: Connect Type-C port with associated USB4 port
thunderbolt: Add Thunderbolt/USB4 <-> USB3 match function
thunderbolt: Expose usb4_port_index() to other modules
thunderbolt: Fix a logic error in wake on connect
thunderbolt: Use wake on connect and disconnect over suspend
|
|
Commit aa7a9275ab81 ("PM: sleep: Suspend async parents after suspending
children") had triggered a suspend issue on Tegra boards because it had
reordered the syspend of devices with async suspend enabled with respect
to some other devices. Specifically, the devices with async suspend
enabled that have no children are now suspended before any other devices
unless there are device links pointing to them as suppliers.
The investigation that followed the failure report uncovered that async
suspend was enabled for the cypd4226 device that was a Type-C controller
with a dependency on USB PHY and it turned out that disabling async
suspend for that device made the issue go away. Since async suspend
takes dependencies between parents and children into account as well
as other dependencies between devices represented by device links, this
means that the cypd4226 has a dependency on another device that is
not represented in any form in the kernel (a "hidden" dependency), in
which case async suspend should not be enabled for it.
Accordingly, make ucsi_ccg_probe() disable async suspend for the
devices handled by, which covers the cypd4226 device on the Tegra
boards as well as other devices likely to have similar "hidden"
dependencies.
Fixes: aa7a9275ab81 ("PM: sleep: Suspend async parents after suspending children")
Closes: https://lore.kernel.org/linux-pm/c6cd714b-b0eb-42fc-b9b5-4f5f396fb4ec@nvidia.com/
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/6180608.lOV4Wx5bFT@rjwysocki.net
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes Type-C Compliance Test TD 4.7.6 - Try.SNK DRP Connect
SNKAS.
The compliance tester moves into SNK_UNATTACHED during toggling and
expects the PUT to apply Rp after tPDDebounce of detection. If the port
is in SNK_TRY_WAIT_DEBOUNCE, it will move into SRC_TRYWAIT immediately
and apply Rp. This violates TD 4.7.5.V.3, where the tester confirms that
the PUT attaches Rp after the transitions to Unattached.SNK for
tPDDebounce.
Change the tcpm_set_state delay between SNK_TRY_WAIT_DEBOUNCE and
SRC_TRYWAIT to tPDDebounce.
Fixes: a0a3e04e6b2c ("staging: typec: tcpm: Check for Rp for tPDDebounce")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250429234703.3748506-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch ensures that the UCSI driver waits for all pending tasks in the
ucsi_displayport_work workqueue to finish executing before proceeding with
the partner removal.
Cc: stable <stable@kernel.org>
Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20250424084429.3220757-3-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch introduces the ucsi_con_mutex_lock / ucsi_con_mutex_unlock
functions to the UCSI driver. ucsi_con_mutex_lock ensures the connector
mutex is only locked if a connection is established and the partner pointer
is valid. This resolves a deadlock scenario where
ucsi_displayport_remove_partner holds con->mutex waiting for
dp_altmode_work to complete while dp_altmode_work attempts to acquire it.
Cc: stable <stable@kernel.org>
Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250424084429.3220757-2-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well, and this resolves the following
merge conflicts that were reported in linux-next:
drivers/usb/chipidea/ci_hdrc_imx.c
drivers/usb/host/xhci.h
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
debugfs.c emits the following warnings when compiling with the -Wsign-conversion flag with clang 15:
drivers/usb/typec/ucsi/debugfs.c:58:27: warning: implicit conversion changes signedness: 'int' to 'u32' (aka 'unsigned int') [-Wsign-conversion]
ucsi->debugfs->status = ret;
~ ^~~
drivers/usb/typec/ucsi/debugfs.c:71:25: warning: implicit conversion changes signedness: 'u32' (aka 'unsigned int') to 'int' [-Wsign-conversion]
return ucsi->debugfs->status;
~~~~~~ ~~~~~~~~~~~~~~~^~~~~~
During ucsi_cmd() we see:
if (ret < 0) {
ucsi->debugfs->status = ret;
return ret;
}
But "status" is u32 meaning unsigned wrap-around occurs when assigning a value which is < 0 to it, this obscures the real status.
To fix this make the "status" of type int since ret is also of type int.
Fixes: df0383ffad64 ("usb: typec: ucsi: Add debugfs for ucsi commands")
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250422134717.66218-1-qasdev00@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
WARNING: unmet direct dependencies detected for DRM_AUX_HPD_BRIDGE
Depends on [n]: HAS_IOMEM [=y] && DRM [=n] && DRM_BRIDGE [=n] && OF [=n]
Selected by [m]:
- UCSI_HUAWEI_GAOKUN [=m] && USB_SUPPORT [=y] && TYPEC [=m] && TYPEC_UCSI [=m] && EC_HUAWEI_GAOKUN [=m]
DRM_AUX_HPD_BRIDGE depends on DRM_BRIDGE and OF, only select it with
both for UCSI_HUAWEI_GAOKUN.
Fixes: 00327d7f2c8c ("usb: typec: ucsi: add Huawei Matebook E Go ucsi driver")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250417122843.2667008-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'cci' may be uninitialized, adding error checking to fix it.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/Z_44zoTyLLdXNkKT@stanley.mountain
Fixes: 00327d7f2c8c ("usb: typec: ucsi: add Huawei Matebook E Go ucsi driver")
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250415172006.126740-1-mitltlatltl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The fsa4480 vcc lane could be driven by some external regulator.
This patch is adding support to enable the regulator before probing.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-typec-mux-fs4480-v1-1-475377ef22a3@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If USB3.x device references USB4 host interface, USB4 port can be
connected with appropriate Type-C port. By using component framework,
and in turn by creating symlinks, userspace can benefit from having
Thunderbolt/USB4 connection to Type-C ports.
Note: This change introduces dependency on Thunderbolt driver as it's
required to properly map USB4 port to Type-C port.
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We recently added some locking to this function but this error path
was accidentally missed. Unlock before returning.
Fixes: ec27386de23a ("usb: typec: class: Fix NULL pointer access")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/Z_44tOtmml89wQcM@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Although some Type-C DRD devices that do not support the DP Sink
function (such as Huawei Mate 40Pro), the Source Port initiates
Enter Mode CMD, but the device responds to Enter Mode ACK, the
Source port then initiates DP Status Update CMD, and the device
responds to DP Status Update NAK.
As PD2.0 spec ("6.4.4.3.4 Enter Mode Command")，A DR_Swap Message
Shall Not be sent during Modal Operation between the Port Partners.
At this time, the source port initiates DR_Swap message through the
"echo device > /sys/class/typec/port0/data_role" command to switch
the data role from host to device. The device will initiate a Hard
Reset for recovery, resulting in the failure of data role swap.
Therefore, when DP Status Update NAK is received, Exit Mode CMD is
initiated to exit the currently entered DP altmode.
Signed-off-by: Jos Wang <joswang@lenovo.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250209071926.69625-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Device can be unbound, so driver must also release memory for the wakeup
source.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250406204051.63446-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Device can be unbound, so driver must also release memory for the wakeup
source.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250406204051.63446-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tcpci chip vbus pin is possibly driven by an regulator. This patch
is adding support to enable an optional vdd regulator before probing.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpci-v1-1-4442c7d0ee1e@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The funciton tcpm_acc_attach is not setting the proper state when
calling tcpm_set_role. The function tcpm_set_role is currently only
handling TYPEC_STATE_USB. For the tcpm_acc_attach to switch into other
modal states tcpm_set_role needs to be extended by an extra state
parameter. This patch is handling the proper state change when calling
tcpm_acc_attach.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpm-v1-3-b99f44badce8@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
