| Age | Commit message (Collapse) | Author |
|---|
|
commit 1a760d10ded37 ("thunderbolt: Fix a logic error in wake on connect")
fixated on the USB4 port sysfs wakeup file not working properly to control
policy, but it had an unintended side effect that the sysfs file controls
policy both at runtime and at suspend time. The sysfs file is supposed to
only control behavior while system is suspended.
Pass whether programming a port for runtime into usb4_switch_set_wake()
and if runtime then ignore the value in the sysfs file.
Cc: stable@vger.kernel.org
Reported-by: Alexander Kovacs <Alexander.Kovacs@amd.com>
Tested-by: Alexander Kovacs <Alexander.Kovacs@amd.com>
Fixes: 1a760d10ded37 ("thunderbolt: Fix a logic error in wake on connect")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This patch introduces a function that can be used to send uevent
notifications in the domain to userspace. For instance, it can indicate
that a DisplayPort tunnel could not be established due to insufficient
bandwidth. Userspace can then forward to user via dialog or similar.
Convert boot_acl_store() to call this instead of open-coding.
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Make usb4_port_index() available to other files in the driver, rename
and add function documentation.
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Router DROM contains information that might be usable for development
and debugging purposes. For example when new entries are added to the
USB4 spec it is useful to be able to look for them without need to
change the kernel.
For this reason expose the DROM through debugfs.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Add support for the RX2 receiver which is used as the third receiver in
asymmetric links. This requires expanding the results array for the
additional third data word of the hardware margining results.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Use ARRAY_SIZE() when available or pass in the array size derived from
it. This is in preparation for adding another result data word for
supporting Gen 4 asymmetric links with an additional lane.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Replace the raw values and macros with an enum and use it consistently.
No functional changes.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Add a debugfs knob for USB4 Gen 4 margining eye selection. Gen 4 uses
3-level pulse amplitude modulation (PAM3) which changes how margining
measurements are made because PAM3 has two eyes per lane from which
the margins can be measured.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Use or pass ARRAY_SIZE() of the capabilities array instead of hardcoding
it. USB4 Gen 4 introduces an additional data word, which requires
expanding the capabilities array.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
USB4 specification defines the metadata needed to perform software
margining, as well as the necessary steps which include waiting for
dwell time.
- Add dwell_time attribute to set the wait time while performing
margining and checking for link errors.
- Add error_counter attribute to configure error counter prior to
margining test.
- Add voltage_time_offset attribute to set the voltage or time offset
steps before performing the software margining test.
- Perform software margining test for dwell duration, break if there are
link errors, stop the clocks and provide results.
Below is a minimalistic example how this can be used. Note these values
are just examples. The exact values in practice depend on host specific
capabilities and the type of measurement to be performed.
# cd /sys/kernel/debug/thunderbolt/ROUTER/portX/margining/
# echo software > mode
# echo 400 > dwell_time
# echo 1 > run
As usual the results attribute contains the results of a succesfull run.
Signed-off-by: R Kannappan <r.kannappan@intel.com>
Co-developed-by: Rene Sapiens <rene.sapiens@intel.com>
Signed-off-by: Rene Sapiens <rene.sapiens@intel.com>
Co-developed-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Add optional extended voltage offset range support for software and
hardware margining as defined by the USB4 specification.
If supported, it can be enabled like below:
# cd /sys/kernel/debug/thunderbolt/ROUTER/portX/margining/
# echo Y > optional_voltage_offset
Signed-off-by: Rene Sapiens <rene.sapiens@intel.com>
Co-developed-by: R Kannappan <r.kannappan@intel.com>
Signed-off-by: R Kannappan <r.kannappan@intel.com>
Co-developed-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Consolidate the hardware and software margining parameters into a single
structure to reduce the number of parameters passed to the margining
functions.
Signed-off-by: Rene Sapiens <rene.sapiens@intel.com>
Co-developed-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Synchronize the operation completion by reading back the software
margining operation completion metadata into margining->results.
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Co-developed-by: R Kannappan <r.kannappan@intel.com>
Signed-off-by: R Kannappan <r.kannappan@intel.com>
Co-developed-by: Rene Sapiens <rene.sapiens@intel.com>
Signed-off-by: Rene Sapiens <rene.sapiens@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Retimers support lane margining as well so make this available through
debugfs in the same way as we do for the USB4 ports. When this is
enabled we also expose retimers on the other side of the cable because
typically margining is implemented only on direction towards the cable.
However, for the retimers on the other side of the cable we do not allow
NVM upgrade to avoid confusing the existing userspace (the same retimer
may now appear twice with different name) and is probably not a good
idea anyway.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In order to add lane margining support for retimers make the margining
functions take sideband target and retimer index as parameters. This
makes it possible to access both router and retimer sideband using the
same functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This makes it possible to read and write USB4 port and retimer sideband
registers through debugfs which is useful for debugging and manufacturing
purposes. We add "sb_regs" debugfs attribute under each USB4 port and
retimer that is used to access the sideband.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We need to call these from other files too so make them available
outside of usb4.c.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It is supposed to be close with the other lane margining functions so
move it there. No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Currently we notify PM core about occurred wakes after any resume. This
is not actually needed after resume from runtime suspend. Hence, notify
PM core about occurred wakes only after resume from system sleep. Also,
if the wake occurred in USB4 router upstream port, we don't notify the
PM core about it since it is not actually needed and can cause
unexpected autowake (e.g. if /sys/power/wakeup_count is used).
While there add the missing kernel-doc for tb_switch_resume().
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the
tb_domain_type, tb_retimer_type, tb_switch_type, usb4_port_device_type,
tb_service_type and tb_xdomain_type variables to be constant structures as
well, placing it into read-only memory which can not be modified at
runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
If a DiplayPort cable is directly connected to the host routers USB4
port, there is no tunnel involved but the port is in "redrive" mode
meaning that it is re-driving the DisplayPort signals from its
DisplayPort source. In this case we need to keep the domain powered on
otherwise once the domain enters D3cold the connected monitor blanks
too.
Since this happens only on Intel Barlow Ridge add a quirk that takes
runtime PM reference if we detect that the USB4 port entered redrive
mode (and release it once it exits the mode).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The USB4 spec says that the Connection Manager should reserve the
bandwidth that is released in the same group for 10 seconds before it
can be shared with other groups. Add support for this. We also delay the
symmetric transition by that same 10 seconds to avoid any unnecessary
transitions (i.e if the released bandwidth is used by another
DisplayPort tunnel in the same group the link can stay asymmetric the
whole time).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Boot firmware (typically BIOS) might have created tunnels of its own.
The tunnel configuration that it does might be sub-optimal. For instance
it may only support HBR2 monitors so the DisplayPort tunnels it created
may limit Linux graphics drivers. In addition there is an issue on some
AMD based systems where the BIOS does not allocate enough PCIe resources
for future topology extension. By resetting the USB4 topology the PCIe
links will be reset as well allowing Linux to re-allocate.
This aligns the behavior with Windows Connection Manager.
We already issued host router reset for USB4 v2 routers, now extend it
to USB4 v1 routers as well. For pre-USB4 (that's Apple systems) we leave
it as is and continue to discover the existing tunnels.
Suggested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This function can be used to clear path config space of an adapter. Make
it available for other files in this driver.
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Introduce a function that issues Downstream Port Reset to a USB4 port.
This supports Thunderbolt 2, 3 and USB4 routers.
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In case of the link is brought up as asymmetric (due to hardware preference), we
honor that and don't transition it to symmetric, unless a router with symmetric
link got plugged below, in the topology (and a bandwidth allows transition to
symmetric).
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We are going to use it in subsequent patches, so make it available outside of
switch.c. Also, change the name to tb_width_name() to follow the naming
conventions.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
USB4 v2 spec defines a Gen 4 link that can operate as an aggregated
symmetric (80/80G) or asymmetric (120/40G). When the link is asymmetric,
the USB4 port on one side of the link operates with three TX lanes and
one RX lane, while the USB4 port on the opposite side of the link
operates with three RX lanes and one TX lane.
Add support for the asymmetric link and provide functions that can be
used to transition the link to asymmetric and back.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This is useful helper to find out the depth of a connected router.
Convert the existing users to call this helper instead of open-coding.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This is useful when walking over upstream lane adapters over given path.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Introduce tb_port_path_direction_downstream() to check if path from
source adapter to destination adapter is directed towards downstream.
Convert existing users to call this helper instead of open-coding.
No functional changes.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
USB4 v2 spec allows USB4 links that are part of a pass through tunnel
(such as DisplayPort and USB 3.x Gen T) to enter lower CL states, which
provide better power management. For this USB4 v2 routers in their path
config space of lane 0 adapter include a new bit PMPS (PM packet
support) that needs to be set.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Rework the function to return the link generation, update the name to
tb_port_get_link_generation(), and make available to the rest of the
driver. This is needed in the subsequent patches.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This function is not used outside of clx.c so make it static. No
functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It turns out there is no need to use the actual link rate when
reclaiming bandwidth for USB 3.x. The reason is that we use consumed
bandwidth which is coming from xHCI when releasing bandwidth (for
example for DisplayPort tunneling) and this can be anything between
1000 Mb/s to maximum, so when reclaiming we can just bump it up back to
maximum instead of actual link rate (which is always <= maximum).
This allows us to get rid of couple of unnecessary lines of code.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The software connection manager needs the device links in order to
establish the tunnels before the native protocols so log a warning if
they are not found.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Make sure the DisplayPort bandwidth allocation mode function names are
consistent with the existing ones, such as USB3.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This is new TMU mode introduced with the USB4 v2. This mode is simpler
than the existing ones and allows all CL states as well. Enable this for
all links where both side routers are v2 and keep the existing
functionality for the v1 and earlier links.
Currently only support the MedRes rate. We can add the HiFi rate later
too if it turns out to be useful.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Move constants related to NVM into nvm.c to make the code cleaner. Use a
separate constant for USB4_DATA_DWORDS in usb4.c.
No functional changes.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
USB4 v2 spec introduces modified encapsulation of PCIe TLP and DLLP
packets. This improves the PCIe tunneled traffic usage by reducing
overhead. Enable this if both sides of the link support it.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
USB4 v2 bumps the per-lane speed up to 40 Gb/s. Also the lanes are
always bonded which gives 80 Gb/s symmetric link (and 120/40 Gb/s
asymmetric). This updates the speed and width of routers and XDomain
connections to support the Gen 4 link. For now we keep the link as is
even if it is already asymmetric.
While there make tb_port_set_link_width() static.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Add a new function usb4_switch_version() that can be used to figure out
the spec version of the router and make tb_switch_is_usb4() to use it as
well. Update the uevent accordingly.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
When USB4 port is in offline mode (this mean there is no device
attached) we want to keep the sideband up to make it possible to
communicate with the retimers. In the same way there is no need to
enable sideband transactions when the USB4 port is not offline as they
are already up.
For this reason make the enabling/disabling depend on the USB4 port
offline status.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In case the boot firmware enabled any of them, read the currently
configured CL states and update the router structure accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This is more natural and follows the hardware register layout better.
This makes it easier to see which CL states we enable (even though they
should be enabled together). Rename 'clx_mask' to 'clx' everywhere as
this is now always bitmask.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
There really don't belong to switch.c so move them into their own file.
As we do this rename the functions to match the conventions used
elsewhere in the driver.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Instead of at enable time we can do this already in
tb_switch_tmu_configure().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This is better to be part of the software connection manager flows in
tb.c. Also name the new function tb_increase_tmu_accuracy() to match
what it actually does.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
tb_switch_tmu_is_enabled()
There is no point passing it as we already have a field for that. While
there clean up the kernel-doc of things that do not really belong to the
API documentation (these can be figured out from the spec itself).
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In the same way we did for the routers add a function that returns the
parent routers downstream facing port for XDomain devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
