| Age | Commit message (Collapse) | Author |
|---|
|
Introduce tb_switch_downstream_port() helper function that returns the
downstream port of a parent switch that is connected to the upstream
port of specified switch. From now on, we use it all across the driver
where applicable.
While there fix a whitespace in comment and rename 'downstream' to
'down' to be consistent with the rest of the driver.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Current Intel USB4 host routers have hardware limitation that the USB3
bandwidth cannot go higher than 16376 Mb/s. Work this around by adding a
new quirk that limits the bandwidth for the affected host routers.
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
According to USB4 retimer specification, the process of firmware update
sequence requires issuing a SET_INBOUND_SBTX port operation that later
shall be followed by UNSET_INBOUND_SBTX port operation. This last step
is not currently issued by the driver but it is necessary to make sure
the retimers are put back to passthrough mode even during enumeration.
If this step is missing the link may not come up properly after
soft-reboot for example.
For this reason issue UNSET_INBOUND_SBTX after SET_INBOUND_SBTX for
enumeration and also when the NVM upgrade is run.
Reported-by: Christian Schaubschläger <christian.schaubschlaeger@gmx.at>
Link: https://lore.kernel.org/linux-usb/b556f5ed-5ee8-9990-9910-afd60db93310@gmx.at/
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Add QUIRK_NO_CLX to disable the CLx state for hardware which
doesn't supports it.
AMD Yellow Carp and Pink Sardine don't support CLx state,
hence disabling it using QUIRK_NO_CLX.
Cc: stable@vger.kernel.org
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
[mw: added debug log when the quirk is run]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
|
|
The uevent() callback in struct device_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Gross <markgross@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Sean Young <sean@mess.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Won Chung <wonchung@google.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for Thunderbolt
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB4 spec defines an optional feature that allows the connection
manager to negotiate with the graphics through DPCD registers changes in
the bandwidth allocation dynamically. This is referred as "bandwidth
allocation mode" in the spec. The connection manager uses DP IN adapters
registers to communicate with the graphics, and also gets notifications
from these adapters when the graphics wants to change the bandwidth
allocation. Both the connection manager and the graphics driver needs to
support this.
We check if the DP IN adapter supports this and if it does enable it
before establishing a DP tunnel. Then we react on DP_BW notifications
coming from the DP IN adapter and update the bandwidth allocation
accordingly (within the maximum common capabilities the DP IN/OUT
support).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
USB4 spec defines an additional feature that DP IN adapters can
implement (alongside with the graphics DPCD register set) to support
more dynamic bandwidth management for DisplayPort tunnels. For the
connection manager the communication happens through the DP IN adapter
using a set of registers in the adapter config space allocated for this.
Add functions that export this functionality for the rest of the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
tb_port_is_clx_enabled() generates a valid warning with gcc-13:
drivers/thunderbolt/switch.c:1286:6: error: conflicting types for 'tb_port_is_clx_enabled' due to enum/integer mismatch; have 'bool(struct tb_port *, unsigned int)' ...
drivers/thunderbolt/tb.h:1050:6: note: previous declaration of 'tb_port_is_clx_enabled' with type 'bool(struct tb_port *, enum tb_clx)' ...
I.e. the type of the 2nd parameter of tb_port_is_clx_enabled() in the
declaration is unsigned int, while the definition spells enum tb_clx.
Synchronize them to the former as the parameter is in fact a mask of the
enum values.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices
supported and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before, and
some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different USB
drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: gadget: uvc: don't put item still in use
usb: gadget: uvc: Fix argument to sizeof() in uvc_register_video()
usb: host: ehci-exynos: switch to using gpiod API
Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"
Revert "USB: fixup for merge issue with "usb: dwc3: Don't switch OTG -> peripheral if extcon is present""
dt-bindings: usb: Convert FOTG210 to dt schema
usb: mtu3: fix failed runtime suspend in host only mode
USB: omap_udc: Fix spelling mistake: "tranceiver_ctrl" -> "transceiver_ctrl"
usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra
usb: typec: Replace custom implementation of device_match_fwnode()
usb: typec: ucsi: Don't warn on probe deferral
usb: add quirks for Lenovo OneLink+ Dock
MAINTAINERS: switch dwc3 to Thinh
usb: idmouse: fix an uninit-value in idmouse_open
USB: PHY: JZ4770: Switch to use dev_err_probe() helper
usb: phy: generic: Switch to use dev_err_probe() helper
usb: ulpi: use DEFINE_SHOW_ATTRIBUTE to simplify ulpi_regs
usb: cdns3: remove dead code
usb: cdc-wdm: Use skb_put_data() instead of skb_put/memcpy pair
usb: musb: sunxi: Switch to use dev_err_probe() helper
...
|
|
Software that has run before the USB4 CM in Linux runs may have disabled
hotplug events for a given lane adapter.
Other CMs such as that one distributed with Windows 11 will enable hotplug
events. Do the same thing in the Linux CM which fixes hotplug events on
"AMD Pink Sardine".
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
As there will be more USB4 devices that support NVM firmware upgrade from
various vendors, it makes sense to split out the Intel specific NVM
image handling from the generic code. This moves the Intel specific NVM
handling into a new structure that will be matched by the device type
and the vendor ID. Do this for both routers and retimers.
This makes it easier to extend the NVM support to cover new vendors and
NVM image formats in the future.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
As we are moving the NVM vendor specifics into nvm.c we need to deal
witht he retimer NVM formats too. For this reason provide retimer
specific function that can be used to read the contents of the NVM and
rename the internal ones accordingly analogous to what we do with
routers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In order to support non-Intel NVM formats the vendor specific NVM
validation code that will live in nvm.c needs to be able to read various
parts of the NVM so make the function available outside of switch.c and
rename it accordingly.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In order to support non-Intel NVM image formats extend the NVM major and
minor version to 32-bits to better accommondate different versioning
schemes.
No functional impact.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
USB4 spec defines standard set of registers to be used for receiver lane
margining. This is useful for I/O interface quality and electrical
robustness validation during manufacturing. Expose receiver lane
margining through new debugfs directory "margining" that is added under
each connected USB4 port. Users can then run the margining by writing to
the exposed attributes under that directory.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We will need this when enabling lane margining support.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Instead of testing just a single CL state we can pass a bitmask of
states to check. This makes it simpler for callers of the function.
We also add a check for CL2 even though not fully supported by the
driver yet.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We are going to need this for lane margining support so make it
available outside of xdomain.c.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Following what we do for routers already, extend this to XDomain
connections as well. This will show in sysfs whether the link is in USB4
or Thunderbolt mode.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of Thunderbolt and USB changes for 6.0-rc1.
Lots of little things here, nothing major, just constant development
on some new hardware support and cleanups of older drivers. Highlights
are:
- lots of typec changes and improvements for new hardware
- new gadget controller driver
- thunderbolt support for new hardware
- the normal set of new usb-serial device ids and cleanups
- loads of dwc3 controller fixes and improvements
- mtu3 driver updates
- testusb fixes for longtime issues (not many people use this tool it
seems.)
- minor driver fixes and improvements over the USB tree
- chromeos platform driver changes were added and then reverted as
they depened on some typec changes, but the cross-tree merges
caused problems so they will come back later through the platform
tree.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (193 commits)
usb: misc: onboard_usb_hub: Remove duplicated power_on delay
usb: misc: onboard_usb_hub: Add TI USB8041 hub support
usb: misc: onboard_usb_hub: Add reset-gpio support
USB: usbsevseg: convert sysfs snprintf to sysfs_emit
dt-bindings: usb: Add binding for TI USB8041 hub controller
ARM: multi_v7_defconfig: enable USB onboard HUB driver
ARM: dts: stm32: add support for USB2514B onboard hub on stm32mp15xx-dkx
usb: misc: onboard-hub: add support for Microchip USB2514B USB 2.0 hub
dt-bindings: usb: generic-ehci: allow usb-hcd schema properties
usb: typec: ucsi: stm32g0: add bootloader support
usb: typec: ucsi: stm32g0: add support for stm32g0 controller
dt-bindings: usb: typec: add bindings for stm32g0 controller
usb: typec: ucsi: Acknowledge the GET_ERROR_STATUS command completion
usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()
usb/chipidea: fix repeated words in comments
usb: renesas-xhci: Do not print any log while fw verif success
usb: typec: retimer: Add missing id check in match callback
USB: xhci: Fix comment typo
usb/typec/tcpm: fix repeated words in comments
usb/musb: fix repeated words in comments
...
|
|
The new implementation of kunit_test_suite() for modules no longer
conflicts with module_init, so can now be used by the thunderbolt tests.
Also update the Kconfig entry to enable the test when KUNIT_ALL_TESTS is
enabled.
This means that kunit_tool can now successfully run and parse the test
results with, for example:
./tools/testing/kunit/kunit.py run --arch=x86_64 \
--kconfig_add CONFIG_PCI=y --kconfig_add CONFIG_USB4=y \
'thunderbolt'
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Daniel Latypov <dlatypov@google.com>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Here we configure TMU mode to HiFi uni-directional once DP tunnel
is created. This is due to accuracy requirement for DP tunneling
as appears in CM guide 1.0, section 7.3.2.
Due to Intel hardware limitation, once we changed the TMU mode to HiFi
uni-directional (when DP tunnel exists), we don't change TMU mode back to
normal uni-directional, even if DP tunnel is torn down later.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In this patch we add support for a second low power state of the link: CL1.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle.
We enable it, if both sides of the link support it,
and only for the first hop router (i.e. the first device that connected
to the host router). This is needed for better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
When bonding lanes over XDomain the host that has "higher" UUID triggers
link re-train for bonding, and the host that has "lower" UUID just waits
for this to happen. To support this split setting the link width and
triggering the actual bonding a separate functions that can be called as
needed.
While there remove duplicated empty line in the kernel-doc comment of
tb_port_lane_bonding_disable().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This should be before tb_wait_for_port() following how the functions in
switch.c are organized.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This makes it consistent with the other logging functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
|
|
Both Alpine Ridge and Titan Ridge require special flows in order to
activate the internal xHCI controller when there is USB device connected
to the downstream type-C port. This implements the missing flows for
both.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
tb_switch_is_alpine_ridge() is missing device ID for Intel Alpine Ridge
dual port version so add this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Low power link states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle. The
simplest one being called CL0s. Follow what we already do for USB4
device routers and enable CL0s for Intel Titan Ridge device router too.
This allows better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Intel Titan Ridge based routers have slightly different flow for time
disruption than USB4 compliant routers. This makes it work on Titan
Ridge too. Needed to enable link low power states on Titan Ridge.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Currently usb4_switch_wait_for_bit() used only in usb4.c Moving to
switch.c to call it from other files. Also change the prefix to "tb_"
to follow to the naming convention.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In this patch we add enabling of CL0s - a low power state of the link.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle. For now,
we add support only for first low power state: CL0s. We enable it, if
both sides of the link support it, and only for the first hop router.
(i.e. the first device that connected to the host router). This is
needed for better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Up until Titan Ridge (Thunderbolt 3) device routers only supported
bi-directional mode. In this patch we add to TMU a uni-directional mode.
The uni-directional mode is needed for enabling of low power state of
the link (CLx).
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
If the boot firmware implements connection manager of its own it may not
create the paths in the same way or order we do. For example it may
create first PCIe tunnel and then USB3 tunnel. When we restore our
tunnels (first de-activating them) we may be doing that over completely
different tunnels and that leaves them possibly non-functional. For this
reason we re-use the tunnel discovery functionality and find out all the
existing tunnels, and tear them down. Once that is done we can restore
our tunnels.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The same way we support these two operations for USB4 routers we can
extend the retimer NVM operations to support retimers also.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It may be useful if the actual NVM authentication can be delayed to be
run later, for instance when the user logs out. For this reason add a
new NVM operation (AUHENTICATE_ONLY) that just triggers the authentication
procedure over whatever was written to the NVM storage.
This is not supported with Thunderbolt 1-3 devices, though.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently these write ops are used for updating router firmware images
only. Moving to tb.h helps the retimers also to use the same ops.
Also add tb_ prefix to the enum while there.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With help from platform firmware (ACPI) it is possible to power on
retimers even when there is no USB4 link (e.g nothing is connected to
the USB4 ports). This allows us to bring the USB4 sideband up so that we
can access retimers and upgrade their NVM firmware.
If the platform has support for this, we expose two additional
attributes under USB4 ports: offline and rescan. These can be used to
bring the port offline, rescan for the retimers and put the port online
again. The retimer NVM upgrade itself works the same way than with cable
connected.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When accessing retimers when there is no cable connected we are going to
need additional USB4 port operations. First the port needs to be put
into offline mode, and then the sideband channel transactions must be
enabled on the SBTX line. This adds support for these operations.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Typically retimers can be accessed only when the USB4 link is up (e.g
there is a cable connected). However, sometimes it is useful to be able
to access retimers even if there is nothing connected to the USB4 port.
For instance we may still want to be able to upgrade the retimer NVM
firmware even if the user does not have any USB4 devices. This is
something that USB4 spec leaves to implementers.
In case of ACPI based systems, we can support this by providing a
special _DSM method under each USB4 port. This _DSM can be used to turn
on power to on-board retimers (and cycle it through different modes so
that the sideband becomes usable).
This patch adds support for this _DSM and makes the functionality
available to the rest of the driver through tb_acpi_power_[on|off]_retimers().
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Create devices for each USB4 port. This is needed when we add retimer
access when there is no device connected but may be useful for other
purposes too following what USB subsystem does. This exports a single
attribute "link" that shows the type of the USB4 link (or "none" if
there is no cable connected).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB4 Connection Manager guide provides detailed information how the
USB4 router buffer (credit) allocation information should be used by the
connection manager when it allocates buffers for different paths. This
patch implements it for Linux. For USB 3.x and DisplayPort we use
directly the router preferences. The rest of the buffer space is then
used for PCIe and DMA (peer-to-peer, XDomain) traffic. DMA tunnels
require at least one buffer and PCIe six, so if there is not enough
buffers we fail the tunnel creation.
For the legacy Thunderbolt 1-3 devices we use the existing hard-coded
scheme except for DMA where we use the values suggested by the USB4 spec
chapter 13.
Co-developed-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Once lane bonding has been enabled (or disabled) both lane adapters may
update their total credits accordingly. For this reason re-read the port
credits after lane bonding has been enabled or disabled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
USB4 routers must expose their preferred credit (buffer) allocation
information through router operation. This information tells the
connection manager how the router prefers its buffers to be allocated to
get the expected bandwidth for the supported protocols.
Read this information and store it as part of struct tb_switch for each
USB4 router.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It may take some time until the two lanes enter bonded state so poll for
the link width to match what is expected before going forward. This ensures
the link is in expected state before we start establishing paths through
it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
With the USB4 buffer allocation the number of credits (and non-flow
credits) may be different depending on the router buffer allocation
preferences. To allow this move the nfc_credits field to struct
tb_path_hop.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Latest USB4 spec added a new wake bit for DisplayPort so add this to the
driver when runtime suspending. This way wake up the domain when a new
monitor is plugged in to any of the device routers.
Also do the same for pre-USB4 devices through the link controller
registers as documented in chapter 13 of the USB4 spec.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We do this for Thunderbolt 2/3 devices through DMA port, USB4 devices
and retimers pretty much the same way. Only the actual block read/write
is different. For this reason split out the NVM read/write functions
from usb4.c to nvm.c and make USB4 device code call these when needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Currently we have had an artificial limitation of a single DMA tunnel
per XDomain connection. However, hardware wise there is no such limit
and software based connection manager can take advantage of all the DMA
rings available on the host to establish tunnels.
For this reason make the tb_xdomain_[enable|disable]_paths() to take the
DMA ring and HopID as parameter instead of storing them in the struct
tb_xdomain. We also add API functions to allocate input and output
HopIDs of the XDomain connection that the service drivers can use
instead of hard-coding.
Also convert the two existing service drivers over to this API.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
