| Age | Commit message (Collapse) | Author |
|---|
|
Many of the Rockchip SoCs support storing trim values for the sensors in
factory programmable memory. These values specify a fixed offset from
the sensor's returned temperature to get a more accurate picture of what
temperature the silicon is actually at.
The way this is implemented is with various OTP cells, which may be
absent. There may both be whole-TSADC trim values, as well as per-sensor
trim values.
In the downstream driver, whole-chip trim values override the per-sensor
trim values. This rewrite of the functionality changes the semantics to
something I see as slightly more useful: allow the whole-chip trim
values to serve as a fallback for lacking per-sensor trim values,
instead of overriding already present sensor trim values.
Additionally, the chip may specify an offset (trim_base, trim_base_frac)
in degrees celsius and degrees decicelsius respectively which defines
what the basis is from which the trim, if any, should be calculated
from. By default, this is 30 degrees Celsius, but the chip can once
again specify a different value through OTP cells.
The implementation of these trim calculations have been tested
extensively on an RK3576, where it was confirmed to get rid of pesky 1.8
degree Celsius offsets between certain sensors.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250610-rk3576-tsadc-upstream-v6-5-b6e9efbf1015@collabora.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The RK3576 SoC has six TS-ADC channels: TOP, BIG_CORE, LITTLE_CORE,
DDR, NPU and GPU.
Signed-off-by: Ye Zhang <ye.zhang@rock-chips.com>
[ported to mainline, reworded commit message]
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250610-rk3576-tsadc-upstream-v6-3-b6e9efbf1015@collabora.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The "v" version specifier here refers to the hardware IP revision.
Mainline deviated from downstream here by calling the v4 revision v3 as
it didn't support the v3 hardware revision at all.
This creates needless confusion, so rename it to rk_tsadcv4_tshut_mode
to be consistent with what the hardware wants to be called.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250610-rk3576-tsadc-upstream-v6-1-b6e9efbf1015@collabora.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The mapping table for the rk3328 is missing the entry for -25C which is
found in the TRM section 9.5.2 "Temperature-to-code mapping".
NOTE: the kernel uses the tsadc_q_sel=1'b1 mode which is defined as:
4096-<code in table>. Whereas the table in the TRM gives the code
"3774" for -25C, the kernel uses 4096-3774=322.
[Dragan Simic] : "After going through the RK3308 and RK3328 TRMs, as
well as through the downstream kernel code, it seems we may have
some troubles at our hands. Let me explain, please.
To sum it up, part 1 of the RK3308 TRM v1.1 says on page 538 that
the equation for the output when tsadc_q_sel equals 1 is (4096 -
tsadc_q), while part 1 of the RK3328 TRM v1.2 says that the output
equation is (1024 - tsadc_q) in that case.
The downstream kernel code, however, treats the RK3308 and RK3328
tables and their values as being the same. It even mentions 1024 as
the "offset" value in a comment block for the rk_tsadcv3_control()
function, just like the upstream code does, which is obviously wrong
"offset" value when correlated with the table on page 544 of part 1
of the RK3308 TRM v1.1.
With all this in mind, it's obvious that more work is needed to make
it clear where's the actual mistake (it could be that the TRM is
wrong), which I'll volunteer for as part of the SoC binning project.
In the meantime, this patch looks fine as-is to me, by offering
what's a clear improvement to the current state of the upstream
code"
Link: https://opensource.rock-chips.com/images/9/97/Rockchip_RK3328TRM_V1.1-Part1-20170321.pdf
Cc: stable@vger.kernel.org
Fixes: eda519d5f73e ("thermal: rockchip: Support the RK3328 SOC in thermal driver")
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20250207175048.35959-1-twoerner@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/thermal to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
On the way make a few whitespace changes to make indention consistent.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241019163412.304422-2-u.kleine-koenig@baylibre.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Switch devm_reset_control_array_get() to
devm_reset_control_array_get_exclusive().
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/202303241108553006227@zte.com.cn
|
|
The RK3588 SoC has seven temperature sensor ADC channels:
- Chip Center
- CPU Cluster 1 (Dual A76 "Big" Cores)
- CPU Cluster 2 (Dual A76 "Big" Cores)
- CPU Cluster 0 (Quad A55 "Little" Cores)
- Power Domain Center
- Graphics Processing Unit
- Neural Processing Unit
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
[rebase, squash fixes]
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230308112253.15659-7-sebastian.reichel@collabora.com
|
|
Dynamically allocate the sensors array based on the amount
of platform sensors in preparation for rk3588 support, which
needs 7 sensors.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230308112253.15659-6-sebastian.reichel@collabora.com
|
|
Replace the channel ID lookup table by a simple offset, since
the channel IDs are consecutive.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230308112253.15659-5-sebastian.reichel@collabora.com
|
|
Use dev_err_probe to simplify error printing in the driver's probe
routine.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230308112253.15659-4-sebastian.reichel@collabora.com
|
|
By using devm_clk_get_enabled() the clock acquisition and
enabling can be done in one step with automatic error
handling.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230308112253.15659-3-sebastian.reichel@collabora.com
|
|
It's possible to directly get the match data in a generic
way nowadays.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230308112253.15659-2-sebastian.reichel@collabora.com
|
|
The thermal->tzp->no_hwmon parameter is only used when calling
thermal_zone_device_register().
Setting it to 'false' before calling thermal_add_hwmon_sysfs() has no
effect.
Remove the call and again prevent the drivers to access the thermal
internals.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> #R-Car
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #Broadcom
Acked-by: Heiko Stuebner <heiko@sntech.de> #rockchip
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some get_temp() ops implementation are showing an error or a debug
message if the reading of the sensor fails.
The debug message is already displayed from the call site of this
ops. So we can remove it.
On the other side, the error should not be displayed because in
production that can raise tons of messages.
Finally, some drivers are showing a debug message with the
temperature, this is also accessible through the trace from the core
code in the temperature_update() function.
Another benefit is the dev_* messages are accessing the thermal zone
device field from the structure, so we encapsulate even more the code
by preventing these accesses.
Remove those messages.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> #Armada
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #brcmstb_thermal.c
Acked-by: Heiko Stuebner <heiko@sntech.de> #rockchip
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The thermal zone device structure is exposed to the different drivers
and obviously they access the internals while that should be
restricted to the core thermal code.
In order to self-encapsulate the thermal core code, we need to prevent
the drivers accessing directly the thermal zone structure and provide
accessor functions to deal with.
Use the devdata accessor introduced in the previous patch.
No functional changes intended.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> #R-Car
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> #MediaTek auxadc and lvts
Reviewed-by: Balsam CHIHI <bchihi@baylibre.com> #Mediatek lvts
Reviewed-by: Adam Ward <DLG-Adam.Ward.opensource@dm.renesas.com> #da9062
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com> #spread
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> #sun8i_thermal
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #Broadcom
Reviewed-by: Dhruva Gole <d-gole@ti.com> # K3 bandgap
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de> #rockchip
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> #uniphier
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202301181639300333679@zte.com.cn
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Don't use "/**" to begin non-kernel-doc comments.
Convert one function description to kernel-doc format.
Prevents these kernel-doc warnings:
drivers/thermal/rockchip_thermal.c:64: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* The max sensors is two in rockchip SoCs.
drivers/thermal/rockchip_thermal.c:179: warning: expecting prototype for TSADC Sensor Register description(). Prototype was for TSADCV2_USER_CON() instead
drivers/thermal/rockchip_thermal.c:1342: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Reset TSADC Controller, reset all tsadc registers.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Amit Kucheria <amitk@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Link: https://lore.kernel.org/r/20230113064500.16103-1-rdunlap@infradead.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The thermal OF code has a new API allowing to migrate the OF
initialization to a simpler approach. The ops are no longer device
tree specific and are the generic ones provided by the core code.
Convert the ops to the thermal_zone_device_ops format and use the new
API to register the thermal zone with these generic ops.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linexp.org>
Link: https://lore.kernel.org/r/20220804224349.1926752-4-daniel.lezcano@linexp.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The tsadc node in rk356x.dtsi has more resets then currently supported
by the rockchip_thermal.c driver, so use
devm_reset_control_array_get() to reset them all.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210930110517.14323-3-jbx6244@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The RK3568 SoCs have two Temperature Sensors, channel 0 is for CPU,
channel 1 is for GPU.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210506175514.168365-5-ezequiel@collabora.com
|
|
Use thermal_zone_device_{en|dis}able() and thermal_zone_device_is_enabled().
Consequently, all set_mode() implementations in drivers:
- can stop modifying tzd's "mode" member,
- shall stop taking tzd's lock, as it is taken in the helpers
- shall stop calling thermal_zone_device_update() as it is called in the
helpers
- can assume they are called when the mode truly changes, so checks to
verify that can be dropped
Not providing set_mode() by a driver no longer prevents the core from
being able to set tzd's mode, so the relevant check in mode_store() is
removed.
Other comments:
- acpi/thermal.c: tz->thermal_zone->mode will be updated only after we
return from set_mode(), so use function parameter in thermal_set_mode()
instead, no need to call acpi_thermal_check() in set_mode()
- thermal/imx_thermal.c: regmap writes and mode assignment are done in
thermal_zone_device_{en|dis}able() and set_mode() callback
- thermal/intel/intel_quark_dts_thermal.c: soc_dts_{en|dis}able() are a
part of set_mode() callback, so they don't need to modify tzd->mode, and
don't need to fall back to the opposite mode if unsuccessful, as the return
value will be propagated to thermal_zone_device_{en|dis}able() and
ultimately tzd's member will not be changed in thermal_zone_device_set_mode().
- thermal/of-thermal.c: no need to set zone->mode to DISABLED in
of_parse_thermal_zones() as a tzd is kzalloc'ed so mode is DISABLED anyway
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-8-andrzej.p@collabora.com
|
|
The function “platform_get_irq” can log an error already.
Thus omit redundant messages for the exception handling in the
calling functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/05f49ae7-5cc7-d6a0-fc3d-abaf2a0b373c@web.de
|
|
By default, of-based thermal drivers do not enable hwmon.
Explicitly enable hwmon for both, the soc and gpu temperature
sensor.
Signed-off-by: Stefan Schaeckeler <schaecsn@gmx.net>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191212061702.BFE2D6E85603@corona.crabdance.com
|
|
Replace a comment starting with /** by simply /* to avoid having it
interpreted as a kernel-doc comment. Describe missing function
parameters where needed.
Fixes up the following warnings when compiled with make W=1:
linux.git/drivers/thermal/rockchip_thermal.c:27: warning: cannot
understand function prototype: 'enum tshut_mode '
linux.git/drivers/thermal/rockchip_thermal.c:37: warning: cannot
understand function prototype: 'enum tshut_polarity '
linux.git/drivers/thermal/rockchip_thermal.c:46: warning: cannot
understand function prototype: 'enum sensor_id '
linux.git/drivers/thermal/rockchip_thermal.c:56: warning: cannot
understand function prototype: 'enum adc_sort_mode '
linux.git/drivers/thermal/rockchip_thermal.c:123: warning: Function
parameter or member 'chn_id' not described in 'rockchip_tsadc_chip'
linux.git/drivers/thermal/rockchip_thermal.c:123: warning: Function
parameter or member 'control' not described in 'rockchip_tsadc_chip'
linux.git/drivers/thermal/rockchip_thermal.c:167: warning: Function
parameter or member 'sensors' not described in 'rockchip_thermal_data'
linux.git/drivers/thermal/rockchip_thermal.c:608: warning: Function
parameter or member 'grf' not described in 'rk_tsadcv2_initialize'
linux.git/drivers/thermal/rockchip_thermal.c:608: warning: Function
parameter or member 'regs' not described in 'rk_tsadcv2_initialize'
linux.git/drivers/thermal/rockchip_thermal.c:608: warning: Function
parameter or member 'tshut_polarity' not described in
'rk_tsadcv2_initialize'
linux.git/drivers/thermal/rockchip_thermal.c:644: warning: Function
parameter or member 'grf' not described in 'rk_tsadcv3_initialize'
linux.git/drivers/thermal/rockchip_thermal.c:644: warning: Function
parameter or member 'regs' not described in 'rk_tsadcv3_initialize'
linux.git/drivers/thermal/rockchip_thermal.c:644: warning: Function
parameter or member 'tshut_polarity' not described in
'rk_tsadcv3_initialize'
linux.git/drivers/thermal/rockchip_thermal.c:732: warning: Function
parameter or member 'regs' not described in 'rk_tsadcv3_control'
linux.git/drivers/thermal/rockchip_thermal.c:732: warning: Function
parameter or member 'enable' not described in 'rk_tsadcv3_control'
linux.git/drivers/thermal/rockchip_thermal.c:1211: warning: Function
parameter or member 'reset' not described in
'rockchip_thermal_reset_controller'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/c3cbdb0619fec602668ba7ae703ba49d67e30b33.1574242756.git.amit.kucheria@linaro.org
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 28694e009e512451ead5519dd801f9869acb1f60.
The commit causes multiple issues in that:
- the added call to ->control does potentially run unclocked
causing a hang of the machine
- the added pinctrl-states are undocumented in the binding
- the added pinctrl-states are not backwards compatible, breaking
old devicetrees.
Fixes: 28694e009e51 ("thermal: rockchip: fix up the tsadc pinctrl setting error")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reported-by: kernelci.org bot <bot@kernelci.org>
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Reported-by: Vicente Bergas <vicencb@gmail.com>
Reported-by: Jack Mitchell <ml@embed.me.uk>
Reported-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
PX30 SOC has two Temperature Sensors for CPU and GPU.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Explicitly use the pinctrl to set/unset the right mode
instead of relying on the pinctrl init mode.
And it requires setting the tshut polarity before select pinctrl.
When the temperature sensor mode is set to 0, it will automatically
reset the board via the Clock-Reset-Unit (CRU) if the over temperature
threshold is reached. However, when the pinctrl initializes, it does a
transition to "otp_out" which may lead the SoC restart all the time.
"otp_out" IO may be connected to the RESET circuit on the hardware.
If the IO is in the wrong state, it will trigger RESET.
(similar to the effect of pressing the RESET button)
which will cause the soc to restart all the time.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
RV1108 SOC has one Temperature Sensor for CPU.
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
RK3328 SOC has one Temperature Sensor for CPU.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
As Ayaka reported the thermal was abormal on rk3288 at booting time.
thermal thermal_zone1: critical temperature reached(125 C),shutting down
thermal thermal_zone2: critical temperature reached(125 C),shutting down
thermal thermal_zone1: critical temperature reached(125 C),shutting down
thermal thermal_zone2: critical temperature reached(125 C),shutting down
...
The root caused by reading the invald analogic value, the value is zero
will convert the 125 degree to trigger the critical temperature.
Fixes it with insteading of the incorrect reading now.
Fixes commit cadf29dc2a8bcaae83
("thermal: rockchip: optimize the conversion table")
Reported-by: ayaka <ayaka@soulik.info>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
In some cases, some sensors didn't need the trip points, the
set_trips will pass {-INT_MAX, INT_MAX} to trigger tsadc alarm in the end,
ignore this case and disable the high temperature interrupt.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
In order to support the valid temperature can conver to analog value.
The rockchip thermal driver has not supported the all valid temperature
to convert the analog value. (e.g.: 61C, 62C, 63C....)
For example:
In some cases, we need adjust the trip point.
$cd /sys/class/thermal/thermal_zone*
$echo 68000 > trip_point_0_temp
That will return the max analogic value indicates the invalid before
posting this patch.
So, this patch will optimize the conversion table to support the other
cases.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The temp_to_code function will return 0 when we set the temperature to a
invalid value (e.g. 61C, 62C, 63C....), that's unpractical. This patch
will prevent this case happening. That will return the max analog value to
indicate the temperature is invalid or over table temperature range.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This driver passes struct chip_tsadc_table by value throughout; this is
inefficient, and AFAICT, there is no reason for it. Let's pass pointers
instead.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
These error messages don't give much information about what went wrong.
It would be nice, for one, to see what invalid temperature was being
requested when conversion fails. It's also good to return an error when
we can't handle a conversion properly.
While we're at it, fix the grammar too.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
It is no necessary to print warning agian and again if we don't
add rockchip,grf for dt, otherwise I saw the following log when
doing suspend-2-resume. We only need to print it once when parsing
dt. It looks quite trivial but the log is apparently verbose.
[ 26.615415] PM: early resume of devices complete after 1.539 msecs
[ 26.622002] rk_tsadcv2_initialize: Missing rockchip,grf property
[ 26.629359] rk_gmac-dwmac ff290000.ethernet: init for RGMII
[ 26.639794] PM: resume of devices complete after 18.109 msecs
[ 26.646925] Restarting tasks ... done.
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Added one additional parameter to thermal_zone_device_update() to provide
caller with an optional capability to specify reason.
Currently this event is used by user space governor to trigger different
processing based on event code. Also it saves an additional call to read
temperature when the event is received.
The following events are cuurently defined:
- Unspecified event
- New temperature sample
- Trip point violated
- Trip point changed
- thermal device up and down
- thermal device power capability changed
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
In less than 10 ms, the temperature of soc will arise 10 degree. 250 ms
is too big for soc tempeture control. Setting 2.5 ms will speed up
temperature accessing speed but introduce no more cpu's computing overhead.
We set AUTO_PERIOD_TIME and TSADCV3_AUTO_PERIOD_HT_TIME the same value,
because normal temperature update speed is also our consern in IPA.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Tested-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Due to the voltage ripple, the sensing data of the tsadc is not accurate.
And in this patch, the bandgap feature is enhanced to remove the voltage
ripple, and then the tsadc can sense the temperature more precisely.
Obsolete codes are removed as well.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Tested-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
The hardware-tracked trips will set the alarm interrupt value for
registers. Then when the thermal zone has no trips to be set,
That make the thermal trips callback a over range value.
The root cause is the rk_tsadcv2_temp_to_code() function to handle the
invalid temperature range is indeed incorrect, let's fix it on now.
Otherwise, the thermal alarm interrupt will be triggered all the time
on some SoCs.
Fox example:
localhost tmp # grep thermal /proc/interrupts; sleep 5;
grep thermal /proc/interrupts
23: 994830 .. GICv3 129 Level rockchip_thermal
23: 1003423 .. GICv3 129 Level rockchip_thermal
Reported-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
We should increase the period cycles to save power since the rk3399 has
the high frequency for tsadc clock.
Fixes commit b0d70338bca22cb14
("thermal: rockchip: Support the RK3399 SoCs in thermal driver")
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Whenever the current temperature is updated, the trip points immediately
below and above the current temperature are found. A sensor driver
callback `set_trips' is then called with the temperatures.
Lastly, The sensor will trigger the hardware high temperature interrupts
to increase the sampleing rate and throttle frequency to limit the
temperature rising When performing passive cooling.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Tested-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Documentation/timers/timers-howto.txt recommends to use
usleep_range on delays > 10usec.
The usleep_range indeed reduces CPU load, since the udelay will busy wait
for enough loop cycles to achieve the desired delay.
Fixes commit b06c52db39fd ("thermal: rockchip:
handle the power sequence for tsadc controller").
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Suggested-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
To update the notes for keeping in mind that quickly in case
someone re-read this driver in the future.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The RK3366 SoCs have two Temperature Sensors, channel 0 is for CPU
channel 1 is for GPU.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This adds the grf property to handle the tsadc power sequence on
rockchip some SoCs.
Verified on rk3399 can work with this patch on now.
while true; do grep "" /sys/class/thermal/thermal_zone[0-1]/temp
sleep .5; done
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41111
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41111
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41666
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41111
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41111
/sys/class/thermal/thermal_zone0/temp:40555
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This patch fixes the incorrect conversion table.
The Code to Temperature mapping is updated based on sillcon results.
Fixes commit b0d70338bca22cb14
("thermal: rockchip: Support the RK3399 SoCs in thermal driver").
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
