| Age | Commit message (Collapse) | Author |
|---|
|
In prepare_function_table() when the pinctrl function table IRQ entries
are generated, the pin bank is calculated from the absolute pin number;
however the IRQ bank mux array is indexed from the first pin bank of the
controller. For R_PIO controllers, this means the absolute pin bank is
way off from the relative pin bank used for array indexing.
Correct this by taking into account the pin base of the controller.
Fixes: f5e2cd34b12f ("pinctrl: sunxi: allow reading mux values from DT")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/20250607135203.2085226-1-wens@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
irq_domain_add_*() interfaces are going away as being obsolete now.
Switch to the preferred irq_domain_create_*() ones. Those differ in the
node parameter: They take more generic struct fwnode_handle instead of
struct device_node. Therefore, of_fwnode_handle() is added around the
original parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/all/20250319092951.37667-31-jirislaby@kernel.org
|
|
As most other Allwinner SoCs before, the A523 chip contains a second
GPIO controller, managing banks PL and PM.
Use the newly introduced DT based pinctrl driver to describe just the
generic pinctrl properties, so advertise the number of pins per bank
and the interrupt capabilities. The actual function/mux assignment is
taken from the devicetree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/20250306235827.4895-9-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Allwinner A523 contains pins in 10 out of the 11 possible pin banks;
it just skips port A.
Use the newly introduced DT based pinctrl driver to describe just the
generic pinctrl properties, so advertise the number of pins per bank
and the interrupt capabilities. The actual function/mux assignment is
taken from the devicetree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/20250306235827.4895-8-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
So far every Allwinner SoC needs a large table in the kernel code, to
describe the mapping between the pinctrl function names ("uart") and
the actual pincontroller mux value to be written into the registers.
This adds a lot of data into a single image kernel, and also looks
somewhat weird, as the DT can easily store the mux value.
Add some code that allows to avoid that table: the struct that describes
the existing pins will be build at *runtime*, based on very basic
information provided by the respective SoC's pinctrl driver. This
consists of the number of pins per bank, plus information which bank
provides IRQ support, along with the mux value to use for that.
The code will then iterate over all children of the pincontroller DT
node (which describe each pin group), and populate that struct with the
mapping between function names and mux values. The only thing that needs
adding in the DT is a property with that value, per pin group.
When this table is built, it will be handed over to the existing sunxi
pinctrl driver, which cannot tell a difference between a hardcoded
struct and this new one built at runtime. It will take care of
registering the pinctrl device with the pinctrl subsystem.
All a new SoC driver would need to do is to provide two arrays, and then
call the sunxi_pinctrl_dt_table_init() function.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/20250306235827.4895-6-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Allwinner pincontroller IP features some registers to control the
withstand voltage of each pin group. So far those registers were always
located at the same offset, but the A523 SoC has moved them (probably to
accommodate all eleven pin banks).
Add a flag to note this feature, and use that to program the registers
either at offset 0x340 or 0x380. So far no pincontroller driver uses
this flag, but we need it for the upcoming A523 support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/20250306235827.4895-5-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Allwinner pincontroller register layout used to allow for at least
11 banks per controller, any more banks would reside at a second
controller instance.
When the per-bank register map size was increased with the D1, it turned
out that the last bank (port K) of those maximum 11 banks actually would
not fit anymore in the 512 bytes reserved for the pincontroller registers.
On new SoCs Allwinner thus moved the last bank beyond the existing
registers, at offset 0x500.
So far SoCs never used more than 9 banks per controller, but the new
Allwinner A523 actually uses all 11 banks. Since that SoC also uses the
extended layout, its PortK needs to be programmed at offset 0x500.
Factor out the bank offset calculation into a new function, and handle
the case for the last bank separately. Since none of the older SoCs ever
used PortK, we can ignore this case, and just always use offset 0x500
for the last bank.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/20250306235827.4895-4-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
By design, the Allwinner pinctrl IP always supported up to 11 GPIO banks,
though no SoC ever used more than 9 banks so far.
The Allwinner A523 has pins in all 11 banks, which exceeds the number of
per-bank regulators that we currently support, as this was set to 9.
Increase the size of the array to hold up to 11 regulator structs, to
support pins in bank J and K as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/20250306235827.4895-3-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For some Allwinner SoCs we have one pinctrl driver caring for multiple
very similar chips, and are tagging certain pins with a variant bitmask.
The Allwinner D1 introduced a slightly extended register layout, and we
were abusing this variant mask to convey this bit of information into
the common code part.
Now there will be more pinctrl device properties to consider (has PortF
voltage switch, for instance), so shoehorning this into the variant
bitmask will not fly anymore.
Refactor the "variant" field into a more generic "flags" field. It turns
out that we don't need the variant bits to be unique across all SoCs,
but only among those SoCs that share one driver (table), of which there
are at most three variants at the moment. So the actual variant field can
be limited to say 8 bits, and the other bits in the flag register can be
re-purposed to hold other information, like this extended register
layout.
As a side effect we can move the variant definition into the per-SoC
pinctrl driver file, which makes it more obvious that this is just a
private definition, only relevant for this particular table.
This also changes the artificial sun20i-d1 "variant" into the actual
flag bit that we are after.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/20250306235827.4895-2-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
lvds, lcd, dsi all shares the same GPIO D bank and lvds0
data 3 lines and lvds1 pins are missed, add them.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Link: https://lore.kernel.org/20241227-a133-display-support-v1-10-13b52f71fb14@linumiz.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
sunxi sunxi_pinctrl_init_with_variant get, enable clk and
deinit_device disable and unprepare it.
This simplifes the code and avoids the calls to
clk_disable_unprepare().
Signed-off-by: Wang Jianzheng <wangjianzheng@vivo.com>
Link: https://lore.kernel.org/20240829064737.16169-1-wangjianzheng@vivo.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Core in platform_driver_register() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Message-ID: <20240330210954.100842-1-krzysztof.kozlowski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some SoCs from the H616 family (such as the T507) have the same die but
more output pins that are used for additional peripherals. The T507 SoC
don't have a built-in multiphy like the AC200 or AC300 connected to the
bank A. With the T507 these pins can be freely used for any other application.
This patch adds the missing muxes on banks A, D and E.
Thanks to Samuel and Andre for the review.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20230916081615.4237-1-iuncuim@gmail.com
Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230714174901.4062397-1-robh@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The sunxi pinctrl has a fixed size array it uses to store regulators used
in the driver. There is currently nothing that ensures that the number of
elements in the array is large enough to map the regulators defined by the
individual SoCs. While this is currently the case having an explicit check
in there will make life easier for anyone debugging memory issues that
manifest in the driver so let's add one.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230712-pinctrl-sunxi-boudns-v1-1-85f37de79b9f@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230310144721.1544669-1-robh@kernel.org
[Dropped hunk hitting drivers/pinctrl/renesas/pinctrl.c]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The D1 pin controller contains muxes for two CAN buses. While the CAN
bus controllers are only documented for the T113 SoC, the pin controller
is the same across all SoC variants.
Signed-off-by: Fabien Poussin <fabien.poussin@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20221126191636.6673-1-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Do not imply that some of the generic headers may be always included.
Instead, include explicitly what we are direct user of.
While at it, sort headers alphabetically.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"There is nothing exciting going on, no core changes, just a few
drivers and cleanups.
New drivers:
- Cypress CY8C95x0 chip pin control support, along with an immediate
cleanup
- Mediatek MT8188 SoC pin control support
- Qualcomm SM8450 and SC8280XP LPASS (low power audio subsystem) pin
control support
- Qualcomm PM7250, PM8450
- Rockchip RV1126 SoC pin control support
Improvements:
- Fix some missing pins in the Armada 37xx driver
- Convert Broadcom and Nomadik drivers to use PINCTRL_PINGROUP()
macro
- Fix some GPIO irq_chips to be immutable
- Massive Qualcomm device tree binding cleanup, with more to come"
* tag 'pinctrl-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (119 commits)
MAINTAINERS: adjust STARFIVE JH7100 PINCTRL DRIVER after file movement
pinctrl: starfive: Rename "pinctrl-starfive" to "pinctrl-starfive-jh7100"
pinctrl: Create subdirectory for StarFive drivers
dt-bindings: pinctrl: st,stm32: Document interrupt-controller property
dt-bindings: pinctrl: st,stm32: Document gpio-hog pattern property
dt-bindings: pinctrl: st,stm32: Document gpio-line-names
pinctrl: st: stop abusing of_get_named_gpio()
pinctrl: wpcm450: Correct the fwnode_irq_get() return value check
pinctrl: bcm: Remove unused struct bcm6328_pingroup
pinctrl: qcom: restrict drivers per ARM/ARM64
pinctrl: bcm: ns: Remove redundant dev_err call
gpio: rockchip: request GPIO mux to pinctrl when setting direction
pinctrl: rockchip: add pinmux_ops.gpio_set_direction callback
pinctrl: cy8c95x0: Align function names in cy8c95x0_pmxops
pinctrl: cy8c95x0: Drop atomicity on operations on push_pull
pinctrl: cy8c95x0: Lock register accesses in cy8c95x0_set_mux()
pinctrl: sunxi: sun50i-h5: Switch to use dev_err_probe() helper
pinctrl: stm32: Switch to use dev_err_probe() helper
dt-bindings: qcom-pmic-gpio: Add PM7250B and PM8450 bindings
pinctrl: qcom: spmi-gpio: Add compatible for PM7250B
...
|
|
In the probe path, dev_err() can be replace with dev_err_probe()
which will check if error code is -EPROBE_DEFER and and prints the
error name.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220917122208.1894769-1-yangyingliang@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The name of A100 R_PIO driver should be sun50i-a100-r-pinctrl,
not sun50iw10p1-r-pinctrl.
Fixes: 473436e7647d6 ("pinctrl: sunxi: add support for the Allwinner A100 pin controller")
Signed-off-by: Michael Wu <michael@allwinnertech.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220819024541.74191-1-michael@allwinnertech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Outside the pinctrl driver and DT bindings we hit some Arm DT files,
patched by the maintainers.
Other than that it is business as usual.
Core changes:
- Add PINCTRL_PINGROUP() helper macro (and use it in the AMD driver).
New drivers:
- Intel Meteor Lake support.
- Reneasas RZ/V2M and r8a779g0 (R-Car V4H).
- AXP209 variants AXP221, AXP223 and AXP809.
- Qualcomm MSM8909, PM8226, PMP8074 and SM6375.
- Allwinner D1.
Improvements:
- Proper pin multiplexing in the AMD driver.
- Mediatek MT8192 can use generic drive strength and pin bias, then
fixes on top plus some I2C pin group fixes.
- Have the Allwinner Sunplus SP7021 use the generic DT schema and
make interrupts optional.
- Handle Qualcomm SC7280 ADSP.
- Handle Qualcomm MSM8916 CAMSS GP clock muxing.
- High impedance bias on ZynqMP.
- Serialize StarFive access to MMIO.
- Immutable gpiochip for BCM2835, Ingenic, Qualcomm SPMI GPIO"
* tag 'pinctrl-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (117 commits)
dt-bindings: pinctrl: qcom,pmic-gpio: add PM8226 constraints
pinctrl: qcom: Make PINCTRL_SM8450 depend on PINCTRL_MSM
pinctrl: qcom: sm8250: Fix PDC map
pinctrl: amd: Fix an unused variable
dt-bindings: pinctrl: mt8186: Add and use drive-strength-microamp
dt-bindings: pinctrl: mt8186: Add gpio-line-names property
ARM: dts: imxrt1170-pinfunc: Add pinctrl binding header
pinctrl: amd: Use unicode for debugfs output
pinctrl: amd: Fix newline declaration in debugfs output
pinctrl: at91: Fix typo 'the the' in comment
dt-bindings: pinctrl: st,stm32: Correct 'resets' property name
pinctrl: mvebu: Missing a blank line after declarations.
pinctrl: qcom: Add SM6375 TLMM driver
dt-bindings: pinctrl: Add DT schema for SM6375 TLMM
dt-bindings: pinctrl: mt8195: Use drive-strength-microamp in examples
Revert "pinctrl: qcom: spmi-gpio: make the irqchip immutable"
pinctrl: imx93: Add MODULE_DEVICE_TABLE()
pinctrl: sunxi: Add driver for Allwinner D1
pinctrl: sunxi: Make some layout parameters dynamic
pinctrl: sunxi: Refactor register/offset calculation
...
|
|
This SoC contains a pinctrl with a new register layout. Use the variant
parameter to set the right register offsets. This pinctrl also increases
the number of functions per pin from 8 to 16, taking advantage of all 4
bits in the mux config field (so far, only functions 0-8 and 14-15 are
used). This increases the maximum possible number of functions.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20220713025233.27248-7-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Starting with the D1/D1s/T113 SoC, Allwinner changed the layout of the
pinctrl registers. This new layout widens the drive level field, which
affects the pull register offset and the overall bank size.
In order to support multiple register layouts, some of the layout
parameters need to be set based on the pinctrl variant. This requires
passing the pinctrl struct pointer to the register/offset calculation
functions.
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220713025233.27248-6-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Starting with the D1/D1s/T113 SoC, Allwinner changed the layout of the
pinctrl registers. This new layout widens the drive level field, which
affects the pull register offset and the overall bank size.
As a first step to support this, combine the register and offset
calculation functions, and refactor the math to depend on one constant
for field widths instead of three. This minimizes the code size impact
of making some of the factors dynamic.
While rewriting these functions, move them to the implementation file,
since that is the only file where they are used. And make the comment
more generic, without mentioning specific offsets/sizes.
The callers are updated to expect a shifted mask, and to use consistent
terminology (reg/shift/mask/val).
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220713025233.27248-5-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
H616 and newer SoCs feature a 2.5V I/O bias mode in addition to the
1.8V and 3.3V modes. This mode is entered by selecting the 3.3V level
and disabling the "withstand function".
H616 supports this capability on its main PIO only. A100 supports this
capability on both its PIO and R-PIO.
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220713025233.27248-4-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
H6 requires I/O bias configuration on both of its PIO devices.
Previously it was only done for the main PIO.
The setting for Port L is at bit 0, so the bank calculation needs to
account for the pin base. Otherwise the wrong bit is used.
Fixes: cc62383fcebe ("pinctrl: sunxi: Support I/O bias voltage setting on H6")
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220713025233.27248-3-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some Allwinner SoCs have 2 pinctrls (PIO and R_PIO).
Previous implementation used absolute pin numbering and it was incorrect
for R_PIO pinctrl.
It's necessary to take into account the base pin number.
Fixes: 90be64e27621 ("pinctrl: sunxi: implement pin_config_set")
Signed-off-by: Andrei Lalaev <andrey.lalaev@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220525190423.410609-1-andrey.lalaev@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
None of the sunxi pin controllers have a module reset line. All of the
SoC documentation, where available, agrees. The bits that would be used
for the PIO reset (i.e. matching the order of the clock gate bits) are
always reserved, both in the CCU and in the PRCM. And experiments on
several SoCs, including the A33, confirm that those reserved bits indeed
have no effect.
Let's remove this superfluous code and dependency, and also remove the
include statement that was copied to the other r_pio drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220531053623.43851-2-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The other NAND pins on Port C use the "nand0" function name.
"nand0" also matches all of the other Allwinner SoCs.
Fixes: 4730f33f0d82 ("pinctrl: sunxi: add allwinner A83T PIO controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220526024956.49500-1-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The manual describes function 0x6 of pin PA2 as "SPI1_CLK", so change
the comment to reflect that.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220504170736.2669595-1-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Change suniv f1c100s pinctrl,PD14 multiplexing function lvds1 to uart2
When the pin PD13 and PD14 is setting up to uart2 function in dts,
there's an error occurred:
1c20800.pinctrl: unsupported function uart2 on pin PD14
Because 'uart2' is not any one multiplexing option of PD14,
and pinctrl don't know how to configure it.
So change the pin PD14 lvds1 function to uart2.
Signed-off-by: IotaHydrae <writeforever@foxmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/tencent_70C1308DDA794C81CAEF389049055BACEC09@qq.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"No core changes this time. Just new driver code and improvements!
New drivers:
- New driver for the Broadcom BCM4908 SoC.
- New subdriver for Tesla FSD (Full Self Driving) SoC, a derivative
of the Samsung Exynos pin control driver.
- New driver for the Amlogic Meson S4 SoC.
- New driver for the Sunplus SP7021 SoC.
- New driver for the Microsemi Ocelot family ServalT SoC.
- New subdriver for Intel Alder Lake-M SoC.
- New subdriver for Intel Ice Lake-N SoC, including PCH support.
- New subdriver for Renesas R8A779F0 SoC.
- New subdriver for Mediatek MT8186 SoC.
- New subdriver for NXP Freescale i.MX93 SoC.
- New driver for Nuvoton WPCM450 SoC.
- New driver for Qualcomm SC8280XP SoC.
Improvements:
- Wakeup support on Samsung Exynos850 and ExynosAutov9.
- Serious and voluminous maintenance cleanup and refactoring in the
Renesas drivers. Mainly sharing similar data between the different
SoC subdrivers.
- Qualcomm SM8450 EGPIO support.
- Drive strength support on the Mediatek MT8195.
- Add some missing groups and functions to the Ralink RT2880"
* tag 'pinctrl-v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (188 commits)
pinctrl: mediatek: common-v1: fix semicolon.cocci warnings
pinctrl: nuvoton: wpcm450: Fix build error without OF
pinctrl: qcom-pmic-gpio: Add support for pm8450
dt-bindings: pinctrl: aspeed: Update gfx node in example
dt-bindings: pinctrl: rt2880: add missing pin groups and functions
pinctrl: ingenic: Fix regmap on X series SoCs
pinctrl: nuvoton: Fix return value check in wpcm450_gpio_register()
pinctrl: nuvoton: wpcm450: off by one in wpcm450_gpio_register()
pinctrl: nuvoton: wpcm450: select GENERIC_PINCTRL_GROUPS
pinctrl: nuvoton: Fix sparse warning
pinctrl: mediatek: mt8186: Account for probe refactoring
pinctrl: mediatek: common-v1: Commonize spec_ies_smt_set callback
pinctrl: mediatek: common-v1: Commonize spec_pupd callback
pinctrl: mediatek: common-v1: Use common probe function
pinctrl: mediatek: common-v1: Add common probe function
pinctrl: mediatek: paris: Unify probe function by using OF match data
pinctrl/rockchip: Add missing of_node_put() in rockchip_pinctrl_probe
pinctrl: nomadik: Add missing of_node_put() in nmk_pinctrl_probe
pinctrl: berlin: fix error return code of berlin_pinctrl_build_state()
pinctrl: qcom: Introduce sc8280xp TLMM driver
...
|
|
This driver, like several others, uses a chained IRQ for each GPIO bank,
and forwards .irq_set_wake to the GPIO bank's upstream IRQ. As a result,
a call to irq_set_irq_wake() needs to lock both the upstream and
downstream irq_desc's. Lockdep considers this to be a possible deadlock
when the irq_desc's share lockdep classes, which they do by default:
============================================
WARNING: possible recursive locking detected
5.17.0-rc3-00394-gc849047c2473 #1 Not tainted
--------------------------------------------
init/307 is trying to acquire lock:
c2dfe27c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0x58/0xa0
but task is already holding lock:
c3c0ac7c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0x58/0xa0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&irq_desc_lock_class);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by init/307:
#0: c1f29f18 (system_transition_mutex){+.+.}-{3:3}, at: __do_sys_reboot+0x90/0x23c
#1: c20f7760 (&dev->mutex){....}-{3:3}, at: device_shutdown+0xf4/0x224
#2: c2e804d8 (&dev->mutex){....}-{3:3}, at: device_shutdown+0x104/0x224
#3: c3c0ac7c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0x58/0xa0
stack backtrace:
CPU: 0 PID: 307 Comm: init Not tainted 5.17.0-rc3-00394-gc849047c2473 #1
Hardware name: Allwinner sun8i Family
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x68/0x90
dump_stack_lvl from __lock_acquire+0x1680/0x31a0
__lock_acquire from lock_acquire+0x148/0x3dc
lock_acquire from _raw_spin_lock_irqsave+0x50/0x6c
_raw_spin_lock_irqsave from __irq_get_desc_lock+0x58/0xa0
__irq_get_desc_lock from irq_set_irq_wake+0x2c/0x19c
irq_set_irq_wake from irq_set_irq_wake+0x13c/0x19c
[tail call from sunxi_pinctrl_irq_set_wake]
irq_set_irq_wake from gpio_keys_suspend+0x80/0x1a4
gpio_keys_suspend from gpio_keys_shutdown+0x10/0x2c
gpio_keys_shutdown from device_shutdown+0x180/0x224
device_shutdown from __do_sys_reboot+0x134/0x23c
__do_sys_reboot from ret_fast_syscall+0x0/0x1c
However, this can never deadlock because the upstream and downstream
IRQs are never the same (nor do they even involve the same irqchip).
Silence this erroneous lockdep splat by applying what appears to be the
usual fix of moving the GPIO IRQs to separate lockdep classes.
Fixes: a59c99d9eaf9 ("pinctrl: sunxi: Forward calls to irq_set_irq_wake")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220216040037.22730-1-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The commit that sets the direction directly without calling
pinctrl_gpio_direction(), forgot to add chip->base to the offset when
calling sunxi_pmx_gpio_set_direction().
This caused failures for various Allwinner boards which have two
GPIO blocks.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: 5kft <5kft@5kft.org>
Suggested-by: 5kft <5kft@5kft.org>
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Fixes: 8df89a7cbc63 (pinctrl-sunxi: don't call pinctrl_gpio_direction())
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/0f536cd8-01db-5d16-2cec-ec6d19409a49@xs4all.nl
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[Picked from linux-next to pinctrl fixes]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This driver, like several others, uses a chained IRQ for each GPIO bank,
and forwards .irq_set_wake to the GPIO bank's upstream IRQ. As a result,
a call to irq_set_irq_wake() needs to lock both the upstream and
downstream irq_desc's. Lockdep considers this to be a possible deadlock
when the irq_desc's share lockdep classes, which they do by default:
============================================
WARNING: possible recursive locking detected
5.17.0-rc3-00394-gc849047c2473 #1 Not tainted
--------------------------------------------
init/307 is trying to acquire lock:
c2dfe27c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0x58/0xa0
but task is already holding lock:
c3c0ac7c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0x58/0xa0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&irq_desc_lock_class);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by init/307:
#0: c1f29f18 (system_transition_mutex){+.+.}-{3:3}, at: __do_sys_reboot+0x90/0x23c
#1: c20f7760 (&dev->mutex){....}-{3:3}, at: device_shutdown+0xf4/0x224
#2: c2e804d8 (&dev->mutex){....}-{3:3}, at: device_shutdown+0x104/0x224
#3: c3c0ac7c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0x58/0xa0
stack backtrace:
CPU: 0 PID: 307 Comm: init Not tainted 5.17.0-rc3-00394-gc849047c2473 #1
Hardware name: Allwinner sun8i Family
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x68/0x90
dump_stack_lvl from __lock_acquire+0x1680/0x31a0
__lock_acquire from lock_acquire+0x148/0x3dc
lock_acquire from _raw_spin_lock_irqsave+0x50/0x6c
_raw_spin_lock_irqsave from __irq_get_desc_lock+0x58/0xa0
__irq_get_desc_lock from irq_set_irq_wake+0x2c/0x19c
irq_set_irq_wake from irq_set_irq_wake+0x13c/0x19c
[tail call from sunxi_pinctrl_irq_set_wake]
irq_set_irq_wake from gpio_keys_suspend+0x80/0x1a4
gpio_keys_suspend from gpio_keys_shutdown+0x10/0x2c
gpio_keys_shutdown from device_shutdown+0x180/0x224
device_shutdown from __do_sys_reboot+0x134/0x23c
__do_sys_reboot from ret_fast_syscall+0x0/0x1c
However, this can never deadlock because the upstream and downstream
IRQs are never the same (nor do they even involve the same irqchip).
Silence this erroneous lockdep splat by applying what appears to be the
usual fix of moving the GPIO IRQs to separate lockdep classes.
Fixes: a59c99d9eaf9 ("pinctrl: sunxi: Forward calls to irq_set_irq_wake")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220216040037.22730-1-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Avoid printing an error message if getting a regulator fails with
EPROBE_DEFER. This can happen if, for example, a regulator supplying
one of the main banks is controlled by a PL pin.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20220217131737.10931-1-mans@mansr.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Two bugs have sneaked in the H616 pinctrl data:
- PH9 uses the mux value of 0x3 twice (one should be 0x5 instead)
- PH8 and PH9 use the "i2s3" function name twice in each pin
For the double pin name we use the same trick we pulled for i2s0: append
the pin function to the group name to designate the special function.
Fixes: 25adc29407fb ("pinctrl: sunxi: Add support for the Allwinner H616 pin controller")
Reported-by: SASANO Takayoshi <uaa@mx5.nisiq.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220105172952.23347-1-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Set the direction directly without calling pinctrl_gpio_direction().
This avoids the mutex_lock() calls in that function, which would
invalid the can_sleep = false.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/20211206131648.1521868-4-hverkuil-cisco@xs4all.nl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates to the interrupt core and driver subsystems:
Core changes:
- The usual set of small fixes and improvements all over the place,
but nothing stands out
MSI changes:
- Further consolidation of the PCI/MSI interrupt chip code
- Make MSI sysfs code independent of PCI/MSI and expose the MSI
interrupts of platform devices in the same way as PCI exposes them.
Driver changes:
- Support for ARM GICv3 EPPI partitions
- Treewide conversion to generic_handle_domain_irq() for all chained
interrupt controllers
- Conversion to bitmap_zalloc() throughout the irq chip drivers
- The usual set of small fixes and improvements"
* tag 'irq-core-2021-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (57 commits)
platform-msi: Add ABI to show msi_irqs of platform devices
genirq/msi: Move MSI sysfs handling from PCI to MSI core
genirq/cpuhotplug: Demote debug printk to KERN_DEBUG
irqchip/qcom-pdc: Trim unused levels of the interrupt hierarchy
irqdomain: Export irq_domain_disconnect_hierarchy()
irqchip/gic-v3: Fix priority comparison when non-secure priorities are used
irqchip/apple-aic: Fix irq_disable from within irq handlers
pinctrl/rockchip: drop the gpio related codes
gpio/rockchip: drop irq_gc_lock/irq_gc_unlock for irq set type
gpio/rockchip: support next version gpio controller
gpio/rockchip: use struct rockchip_gpio_regs for gpio controller
gpio/rockchip: add driver for rockchip gpio
dt-bindings: gpio: change items restriction of clock for rockchip,gpio-bank
pinctrl/rockchip: add pinctrl device to gpio bank struct
pinctrl/rockchip: separate struct rockchip_pin_bank to a head file
pinctrl/rockchip: always enable clock for gpio controller
genirq: Fix kernel doc indentation
EDAC/altera: Convert to generic_handle_domain_irq()
powerpc: Bulk conversion to generic_handle_domain_irq()
nios2: Bulk conversion to generic_handle_domain_irq()
...
|
|
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
When we are building all the various pinctrl structures for the
Allwinner pinctrl devices, we do some estimation about the maximum
number of distinct function (names) that we will need.
So far we take the number of pins as an upper bound, even though we
can actually have up to four special functions per pin. This wasn't a
problem until now, since we indeed have typically far more pins than
functions, and most pins share common functions.
However the H616 "-r" pin controller has only two pins, but four
functions, so we run over the end of the array when we are looking for
a matching function name in sunxi_pinctrl_add_function - there is no
NULL sentinel left that would terminate the loop:
[ 8.200648] Unable to handle kernel paging request at virtual address fffdff7efbefaff5
[ 8.209179] Mem abort info:
....
[ 8.368456] Call trace:
[ 8.370925] __pi_strcmp+0x90/0xf0
[ 8.374559] sun50i_h616_r_pinctrl_probe+0x1c/0x28
[ 8.379557] platform_probe+0x68/0xd8
Do an actual worst case allocation (4 functions per pin, three common
functions and the sentinel) for the initial array allocation. This is
now heavily overestimating the number of functions in the common case,
but we will reallocate this array later with the actual number of
functions, so it's only temporarily.
Fixes: 561c1cf17c46 ("pinctrl: sunxi: Add support for the Allwinner H616-R pin controller")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210722132548.22121-1-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There are only two pins left now, used to connect to the PMIC via I2C.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210118020848.11721-6-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Port A is used for an internal connection to some analogue circuitry
which looks like an AC200 IP (as in the H6), though this is not
mentioned in the manual.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20210118020848.11721-5-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As there is an RSB controller in the H6 SoC, there should be some pin
configuration for it. While no such configuration is documented, the
"s_i2c" pins are suspiciously on the "alternate" function 3, with no
primary function 2 given. This suggests the primary function for these
pins is actually RSB, and that is indeed the case.
Add the "s_rsb" pin functions so the RSB controller can be used.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20210103100007.32867-3-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
sunxi_pinctrl_irq_handler
It is found on many allwinner soc that there is a low probability that
the interrupt status cannot be read in sunxi_pinctrl_irq_handler. This
will cause the interrupt status of a gpio bank to always be active on
gic, preventing gic from responding to other spi interrupts correctly.
So we should call the chained_irq_* each time enter sunxi_pinctrl_irq_handler().
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/85263ce8b058e80cea25c6ad6383eb256ce96cc8.1604988979.git.frank@allwinnertech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
with WARN_ON
The interrupt descriptor cannot be found in the interrupt processing
function, and this situation cannot happen when the system is running
normally. It doesn't seem right to return directly to the status of not
handling gic. In this case, it must be a bug, let's mark it with
WARN_ON.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Link: https://lore.kernel.org/r/470ebae22fc5434ad5409c4f6e29255467b3cef6.1604988979.git.frank@allwinnertech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A100's pin starts with PB, so it should start with 1.
Fixes: 473436e7647d6 ("pinctrl: sunxi: add support for the Allwinner A100 pin controller")
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Link: https://lore.kernel.org/r/9db51667bf9065be55beafd56e5c319e3bbe8310.1604988979.git.frank@allwinnertech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit introduces support for the pin controller on A100.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/4e331a2ed4a30c883df6157bc5c52bb686aa8e0d.1595572867.git.frank@allwinnertech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When checking the logs on my sun8i-a33-olinuxino I saw:
sun8i-a23-r-pinctrl 1f02c00.pinctrl: Reset controller missing
but this driver was working after.
This message is just here because the reset controller was still not probed.
So don't say anything if the return code say to wait.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Link: https://lore.kernel.org/r/1585818532-23051-1-git-send-email-clabbe@baylibre.com
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
