| Age | Commit message (Collapse) | Author |
|---|
|
Extend the USB+DP combo QMP PHY driver to support the SAR2130P platform.
It mosly follows the SM8550 QMP PHY, but the QSERDES programming
differs, most likely because of the parent clock rate differences.
NOTE: The DP part wasn't yet tested, but it is not possible to support
just the USB part of the PHY. DP part might require additional fixes
later.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241021-sar2130p-phys-v2-3-d883acf170f7@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New hardware support:
- ST STM32MP25 combophy support
- Sparx5 support for lan969x serdes and updates to driver to support
this
- NXP PTN3222 eUSB2 to USB2 redriver
- Qualcomm SAR2130P eusb2 support, QCS8300 USB DW3 and QMP USB2
support, X1E80100 QMP PCIe PHY Gen4 support, QCS615 and QCS8300 QMP
UFS PHY support and SA8775P eDP PHY support
- Rockchip rk3576 usbdp and rk3576 usb2 phy support
- Binding for Microchip ATA6561 can phy
Updates:
- Freescale driver updates from hdmi support
- Conversion of rockchip rk3228 hdmi phy binding to yaml
- Broadcom usb2-phy deprecated support dropped and USB init array
update for BCM4908
- TI USXGMII mode support in J7200
- Switch back to platform_driver::remove() subsystem update"
* tag 'phy-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (59 commits)
phy: qcom: qmp: Fix lecacy-legacy typo
phy: lan969x-serdes: add support for lan969x serdes driver
dt-bindings: phy: sparx5: document lan969x
phy: sparx5-serdes: add support for branching on chip type
phy: sparx5-serdes: add indirection layer to register macros
phy: sparx5-serdes: add function for getting the CMU index
phy: sparx5-serdes: add ops to match data
phy: sparx5-serdes: add constant for the number of CMU's
phy: sparx5-serdes: add constants to match data
phy: sparx5-serdes: add support for private match data
phy: bcm-ns-usb2: drop support for old binding variant
dt-bindings: phy: bcm-ns-usb2-phy: drop deprecated variant
dt-bindings: phy: Add QMP UFS PHY compatible for QCS8300
dt-bindings: phy: qcom: snps-eusb2: Add SAR2130P compatible
dt-bindings: phy: ti,tcan104x-can: Document Microchip ATA6561
phy: airoha: Fix REG_CSR_2L_RX{0,1}_REV0 definitions
phy: airoha: Fix REG_CSR_2L_JCPLL_SDM_HREN config in airoha_pcie_phy_init_ssc_jcpll()
phy: airoha: Fix REG_PCIE_PMA_TX_RESET config in airoha_pcie_phy_init_csr_2l()
phy: airoha: Fix REG_CSR_2L_PLL_CMN_RESERVE0 config in airoha_pcie_phy_init_clk_out()
phy: phy-rockchip-samsung-hdptx: Don't request RST_PHY/RST_ROPLL/RST_LCPLL
...
|
|
Introduced in Commit b3982f2144e1 ("phy: qcom-qmp-combo: restructure
PHY creation"). No functional changes.
Signed-off-by: Konrad Dybcio <quic_kdybcio@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240903-topic-qmp_typo-v1-1-781e81799992@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Commit 44aff8e31080 ("phy: qcom-qmp-combo: clean up probe
initialisation") removed most users of the platform device driver data,
but mistakenly also removed the initialisation despite the data still
being used in the runtime PM callbacks.
The initialisation was soon after restored by commit 83a0bbe39b17 ("phy:
qcom-qmp-combo: add support for updated sc8280xp binding") but now
happens slightly later during probe. This should not cause any trouble
currently as runtime PM needs to be enabled manually through sysfs and
the platform device would not be suspended before the PHY has been
registered anyway.
Move the driver data initialisation to avoid a NULL-pointer dereference
on runtime suspend if runtime PM is ever enabled by default in this
driver.
Fixes: 44aff8e31080 ("phy: qcom-qmp-combo: clean up probe initialisation")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240911115253.10920-5-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
These register prints are useful to validate the init sequence against the
Qcom internal documentation and also to share with the Qcom hw engineers to
debug issues related to PHY.
Sample debug prints:
qcom-qmp-pcie-phy 1c0e000.phy: Writing Reg: QSERDES_V5_COM_SYSCLK_EN_SEL Offset: 0x0094 Val: 0xd9
qcom-qmp-pcie-phy 1c0e000.phy: Writing Reg: QSERDES_V5_COM_HSCLK_SEL Offset: 0x0158 Val: 0x11
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240731152548.102987-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Currently, none of the X1E80100 supported boards upstream have enabled
DP. As for USB, the reason it is not broken when it's obvious that the
offsets are wrong is because the only difference with respect to USB is
the difference in register name. The V6 uses QPHY_V6_PCS_CDR_RESET_TIME
while V6 N4 uses QPHY_V6_N4_PCS_RX_CONFIG. Now, in order for the DP to
work, the DP serdes tables need to be added as they have different
values for V6 N4 when compared to V6 ones, even though they use the same
V6 offsets. While at it, switch swing and pre-emphasis tables to V6 as
well.
Fixes: d7b3579f84f7 ("phy: qcom-qmp-combo: Add x1e80100 USB/DP combo phys")
Co-developed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240527-x1e80100-phy-qualcomm-combo-fix-dp-v1-3-be8a0b882117@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull generic phy updates from Vinod Koul:
"New HW Support:
- Support for Embedded DisplayPort and DisplayPort submodes and
driver support on Qualcomm X1E80100 edp driver
- Qualcomm QMP UFS PHY for SM8475, QMP USB phy for QDU1000/QRU1000
and eusb2-repeater for SMB2360
- Samsung HDMI PHY for i.MX8MP, gs101 UFS phy
- Mediatek XFI T-PHY support for mt7988
- Rockchip usbdp combo phy driver
Updates:
- Qualcomm x4 lane EP support for sa8775p, v4 ad v6 support for
X1E80100, SM8650 tables for UFS Gear 4 & 5 and correct voltage
swing tables
- Freescale imx8m-pci pcie link-up updates
- Rockchip rx-common-refclk-mode support
- More platform remove callback returning void conversions"
* tag 'phy-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (43 commits)
dt-bindings: phy: qcom,usb-snps-femto-v2: use correct fallback for sc8180x
dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: fix msm899[68] power-domains
dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: fix x1e80100-gen3x2 schema
phy: qcpm-qmp-usb: Add support for QDU1000/QRU1000
dt-bindings: phy: qcom,qmp-usb: Add QDU1000 USB3 PHY
dt-bindings: phy: qcom,usb-snps-femto-v2: Add bindings for QDU1000
phy: qcom-qmp-pcie: add x4 lane EP support for sa8775p
phy: samsung-ufs: ufs: exit on first reported error
phy: samsung-ufs: ufs: remove superfluous mfd/syscon.h header
phy: rockchip: fix CONFIG_TYPEC dependency
phy: rockchip: usbdp: fix uninitialized variable
phy: rockchip-snps-pcie3: add support for rockchip,rx-common-refclk-mode
dt-bindings: phy: rockchip,pcie3-phy: add rockchip,rx-common-refclk-mode
phy: rockchip: add usbdp combo phy driver
dt-bindings: phy: add rockchip usbdp combo phy document
phy: add driver for MediaTek XFI T-PHY
dt-bindings: phy: mediatek,mt7988-xfi-tphy: add new bindings
phy: freescale: fsl-samsung-hdmi: Convert to platform remove callback returning void
phy: qcom: qmp-ufs: update SM8650 tables for Gear 4 & 5
MAINTAINERS: Add phy-gs101-ufs file to Tensor GS101.
...
|
|
Commit 5abed58a8bde ("phy: qcom: qmp-combo: Fix VCO div offset on v3")
fixed a regression introduced in 6.5 by making sure that the correct
offset is used for the DP_PHY_VCO_DIV register on v3 hardware.
Unfortunately, that fix instead broke DisplayPort on v5_5nm and v6
hardware as it failed to add the corresponding offsets also to those
register tables.
Fixes: 815891eee668 ("phy: qcom-qmp-combo: Introduce orientation variable")
Fixes: 5abed58a8bde ("phy: qcom: qmp-combo: Fix VCO div offset on v3")
Cc: stable@vger.kernel.org # 6.5: 5abed58a8bde
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20240408093023.506-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This brings rockchip,pcie3-phy changes into next which incoming patches
are dependent on
|
|
The register base that was used to write to the QSERDES_DP_PHY_MODE
register was 'dp_dp_phy' before commit 815891eee668 ("phy:
qcom-qmp-combo: Introduce orientation variable"). There isn't any
explanation in the commit why this is changed, so I suspect it was an
oversight or happened while being extracted from some other series.
Oddly the value being 0x4c or 0x5c doesn't seem to matter for me, so I
suspect this is dead code, but that can be fixed in another patch. It's
not good to write to the wrong register space, and maybe some other
version of this phy relies on this.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Abel Vesa <abel.vesa@linaro.org>
Cc: Steev Klimaszewski <steev@kali.org>
Cc: Johan Hovold <johan+linaro@kernel.org>
Cc: Bjorn Andersson <quic_bjorande@quicinc.com>
Cc: stable@vger.kernel.org # 6.5
Fixes: 815891eee668 ("phy: qcom-qmp-combo: Introduce orientation variable")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240405000111.1450598-1-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Commit ec17373aebd0 ("phy: qcom: qmp-combo: extract common function to
setup clocks") changed the offset that is used to write to
DP_PHY_VCO_DIV from QSERDES_V3_DP_PHY_VCO_DIV to
QSERDES_V4_DP_PHY_VCO_DIV. Unfortunately, this offset is different
between v3 and v4 phys:
#define QSERDES_V3_DP_PHY_VCO_DIV 0x064
#define QSERDES_V4_DP_PHY_VCO_DIV 0x070
meaning that we write the wrong register on v3 phys now. Add another
generic register to 'regs' and use it here instead of a version specific
define to fix this.
This was discovered after Abhinav looked over register dumps with me
from sc7180 Trogdor devices that started failing to light up the
external display with v6.6 based kernels. It turns out that some
monitors are very specific about their link clk frequency and if the
default power on reset value is still there the monitor will show a
blank screen or a garbled display. Other monitors are perfectly happy to
get a bad clock signal.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: ec17373aebd0 ("phy: qcom: qmp-combo: extract common function to setup clocks")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240404234345.1446300-1-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The QMP USB3/DP PHY found in the SM8650 SoC requires a slightly
different Voltage Swing table for HBR/RBR link speeds.
Add a new hbr/rbr voltage switch table named "v6" used in a new
sm8650 qmp_phy_cfg struct replacing the sm8550 fallback used for
the sm8650 compatible.
Fixes: 80c1afe8c5fe ("phy: qcom: qmp-combo: add QMP USB3/DP PHY tables for SM8650")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240226-topic-sm8650-upstream-combo-phy-swing-update-v1-1-08707ebca92a@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Remove duplicate "return 0" in qmp_v4_configure_dp_phy()
Fixes: 186ad90aa49f ("phy: qcom: qmp-combo: reuse register layouts for even more registers")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20240228-topic-sm8x50-upstream-phy-combo-fix-duplicate-return-v1-1-60027a37cab1@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New hardware support:
- Qualcomm X1E80100 PCIe phy support, SM8550 PCIe1 PHY, SC7180 UFS
PHY and SDM630 USBC support
- Rockchip HDMI/eDP Combo PHY driver
- Mediatek MT8365 CSI phy driver
Updates:
- Rework on Qualcomm phy PCS registers and type-c handling
- Cadence torrent phy updates for multilink configuration
- TI gmii resume support"
* tag 'phy-for-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (41 commits)
phy: constify of_phandle_args in xlate
phy: ti: tusb1210: Define device IDs
phy: ti: tusb1210: Use temporary variable for struct device
phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver
dt-bindings: phy: Add Rockchip HDMI/eDP Combo PHY schema
phy: ti: gmii-sel: add resume support
phy: mtk-mipi-csi: add driver for CSI phy
dt-bindings: phy: add mediatek MIPI CD-PHY module v0.5
phy: cadence-torrent: Add USXGMII(156.25MHz) + SGMII/QSGMII(100MHz) multilink config for TI J7200
dt-bindings: phy: cadence-torrent: Add a separate compatible for TI J7200
phy: cadence-torrent: Add USXGMII(156.25MHz) + SGMII/QSGMII(100MHz) multilink configuration
phy: cadence-torrent: Add PCIe(100MHz) + USXGMII(156.25MHz) multilink configuration
dt-bindings: phy: cadence-torrent: Add optional input reference clock for PLL1
phy: qcom-qmp-ufs: Switch to devm_clk_bulk_get_all() API
dt-bindings: phy: qmp-ufs: Fix PHY clocks
phy: qcom: sgmii-eth: move PCS registers to separate header
phy: qcom: sgmii-eth: use existing register definitions
phy: qcom: qmp-usbc: drop has_pwrdn_delay handling
phy: qcom: qmp: move common bits definitions to common header
phy: qcom: qmp: split DP PHY registers to separate headers
...
|
|
Due to a long-standing issue in driver core, drivers may not probe defer
after having registered child devices to avoid triggering a probe
deferral loop (see fbc35b45f9f6 ("Add documentation on meaning of
-EPROBE_DEFER")).
Move registration of the typec switch to after looking up clocks and
other resources.
Note that PHY creation can in theory also trigger a probe deferral when
a 'phy' supply is used. This does not seem to affect the QMP PHY driver
but the PHY subsystem should be reworked to address this (i.e. by
separating initialisation and registration of the PHY).
Fixes: 2851117f8f42 ("phy: qcom-qmp-combo: Introduce orientation switching")
Cc: stable@vger.kernel.org # 6.5
Cc: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240217150228.5788-7-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Due to a long-standing issue in driver core, drivers may not probe defer
after having registered child devices to avoid triggering a probe
deferral loop (see fbc35b45f9f6 ("Add documentation on meaning of
-EPROBE_DEFER")).
This could potentially also trigger a bug in the DRM bridge
implementation which does not expect bridges to go away even if device
links may avoid triggering this (when enabled).
Move registration of the DRM aux bridge to after looking up clocks and
other resources.
Note that PHY creation can in theory also trigger a probe deferral when
a 'phy' supply is used. This does not seem to affect the QMP PHY driver
but the PHY subsystem should be reworked to address this (i.e. by
separating initialisation and registration of the PHY).
Fixes: 35921910bbd0 ("phy: qcom: qmp-combo: switch to DRM_AUX_BRIDGE")
Fixes: 1904c3f578dc ("phy: qcom-qmp-combo: Introduce drm_bridge")
Cc: stable@vger.kernel.org # 6.5
Cc: Bjorn Andersson <quic_bjorande@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240217150228.5788-6-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The xlate callbacks are supposed to translate of_phandle_args to proper
provider without modifying the of_phandle_args. Make the argument
pointer to const for code safety and readability.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Link: https://lore.kernel.org/r/20240217093937.58234-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Move bit definitions for the common headers to the common phy-qcom-qmp.h
header.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-5-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Split the DP PHY register definitions to separate headers, removing them
from the global one.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-4-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Move common init tables code to the common header phy-qcom-qmp-common.h.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-3-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New Support:
- Qualcomm SM8650 UFS, PCIe and USB/DP Combo PHY, eUSB2 PHY, SDX75
USB3, X1E80100 USB3 support
- Mediatek MT8195 support
- Rockchip RK3128 usb2 support
- TI SGMII mode for J784S4
Updates:
- Qualcomm v7 register offsets updates
- Mediatek tphy support for force phy mode switch"
* tag 'phy-for-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (34 commits)
phy: ti: j721e-wiz: Add SGMII support in WIZ driver for J784S4
phy: ti: gmii-sel: Enable SGMII mode for J784S4
phy: qcom-qmp-usb: Add Qualcomm X1E80100 USB3 PHY support
dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: Add X1E80100 USB PHY binding
phy: qcom-qmp-combo: Add x1e80100 USB/DP combo phys
dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp-phy: Document X1E80100 compatible
dt-bindings: phy: qcom: snps-eusb2: Document the X1E80100 compatible
phy: mediatek: tphy: add support force phy mode switch
dt-bindings: phy: mediatek: tphy: add a property for force-mode switch
phy: phy-can-transceiver: insert space after include
phy: qualcomm: phy-qcom-qmp-ufs: Rectify SM8550 UFS HS-G4 PHY Settings
dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp-phy: fix path to header
phy: renesas: phy-rcar-gen2: use select for GENERIC_PHY
phy: qcom-qmp: qserdes-txrx: Add v7 register offsets
phy: qcom-qmp: qserdes-txrx: Add V6 N4 register offsets
phy: qcom-qmp: qserdes-com: Add v7 register offsets
phy: qcom-qmp: pcs-usb: Add v7 register offsets
phy: qcom-qmp: pcs: Add v7 register offsets
phy: qcom-qmp: qserdes-txrx: Add some more v6.20 register offsets
phy: qcom-qmp: qserdes-com: Add some more v6 register offsets
...
|
|
The X1E80100 has three copies of an USB/DP compbo PHY, add support for this
to the Qualcomm QMP PHY driver.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20231201-x1e80100-phy-combo-v1-2-6938ec41f3ac@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Switch to using the new DRM_AUX_BRIDGE helper to create the
transparent DRM bridge device instead of handcoding corresponding
functionality.
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231203114333.1305826-3-dmitry.baryshkov@linaro.org
|
|
Add QMP USB3/DP Combo PHY support for the SM8650 platform.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231030-topic-sm8650-upstream-phy-v2-7-a543a4c4b491@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Make sure that we use only v6 registers in qmp_v6_usb3phy_regs_layout.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230928105445.1210861-4-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
For all other generations, we have been using just the QPHY prefix for
the PCS registers. Remove the _USB part of the QPHY_USB prefix.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230928105445.1210861-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Currently, PCS_USB registers that have their initialization data in a
pcs_usb_tbl table are never initialized. Fix that.
Fixes: fc64623637da ("phy: qcom-qmp-combo,usb: add support for separate PCS_USB region")
Reported-by: Adrien Thierry <athierry@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230829-topic-8550_usbphy-v3-2-34ec434194c5@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
There are two instances of the POWER_STATE_CONFIG1 register: one in
the PCS space and another one in PCS_USB.
The downstream init sequence pokes the latter one while we've been poking
the former one (and misnamed it as the latter one, impostor!). Fix that
up to avoid UB.
Fixes: 49742e9edab3 ("phy: qcom-qmp-combo: Add support for SM8550")
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230829-topic-8550_usbphy-v3-1-34ec434194c5@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
During rebase of qcom-qmp-combo series a call to devm_clk_bulk_get_all()
got moved by git from qmp_combo_parse_dt_legacy() to
phy_dp_clks_register(). This doesn't have any serious effect, since the
clocks will be set in both legacy and non-legacy paths. However let's
move it back to place anyway, to prevent the driver from fetching clocks
twice.
Fixes: 28e265bf84a8 ("phy: qcom-qmp-combo: simplify clock handling")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820235813.562284-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add separate device entry for Combo USB+DP QMP PHY on sc7280 platform.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230711120916.4165894-5-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In order to support newer style bindings for combo PHYs, populate
offsets for all Combo QMP PHY configurations.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230711120916.4165894-4-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
For the existing PHYs for new binding we are going to drop ref_clk_src
clock and always use ref clock. Rather than introducing additional code
to handle legacy vs current bindings (and clock names), use
devm_clk_bulk_get_optional() when new bindings are used and
devm_clk_bulk_get_all() when legacy bindings are in place.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230711120916.4165894-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/phy/phy-can-transceiver.c
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20230714174841.4061919-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Extact qmp_combo_configure_dp_clocks(), a common function to setup PHY
clocks depending on the selected link rate.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230621153317.1025914-8-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The only difference between qmp_v6_dp_aux_init() and
qmp_v4_dp_aux_init() is the address of COM_BIAS_EN_CLKBUFLR_EN register.
Move it to register layout and drop the duplicate function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230621153317.1025914-7-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The functions qmp_v5_configure_dp_phy() and qmp_v6_configure_dp_phy()
are now copies of qmp_v4_configure_dp_phy(). Drop them and use the v4
function in all the cases.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230621153317.1025914-6-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Use register layout for TX_HIGHZ_DRVR_EN and TX_TRANSCEIVER_BIAS_EN
registers. This will allow us to unify qmp_v[456]_configure_dp_phy()
functions in the next commit.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230621153317.1025914-5-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Instead of passing additional registers to qmp_combo_configure_dp_swing(),
reuse qphy_reg_layout and add those registers to register layout maps.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230621153317.1025914-4-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Instead of passing additional registers to qmp_v456_configure_dp_phy(),
reuse qphy_reg_layout and add those registers to register layout maps.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230621153317.1025914-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
It seems the commit a2e927b0e50d ("phy: qcom-qmp-combo: Add sc8280xp
USB/DP combo phys") contained a typo for selecting bias0_en values.
First, bias0_en and bias1_en are expected to be symmetrical, and then
the vendor driver also uses `flipped : 0x3E : 0x15` statement for
bias0_en. Correct bias0_en programming to follow this.
Fixes: 49742e9edab3 ("phy: qcom-qmp-combo: Add support for SM8550")
Fixes: a2e927b0e50d ("phy: qcom-qmp-combo: Add sc8280xp USB/DP combo phys")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230621153317.1025914-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
SM8150 and SC8180X are close relatives. Reuse sc8180x data to support
USB+DP combo PHY on SM8150 platform.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230531023415.1209301-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The SM8550 PHY also uses a different offset for the CMN_STATUS reg,
use the right one for the v6 Display Port configuration.
Fixes: 49742e9edab3 ("phy: qcom-qmp-combo: Add support for SM8550")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230601-topic-sm8550-upstream-dp-phy-init-fix-v1-1-4e9da9f97991@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The QMP combo PHY sits in an of_graph connected between the DisplayPort
controller and a USB Type-C connector (or possibly a redriver).
The TCPM needs to be able to convey the HPD signal to the DisplayPort
controller, but no directly link is provided by DeviceTree so the signal
needs to "pass through" the QMP combo phy.
Handle this by introducing a drm_bridge which upon initialization finds
the next bridge (i.e. the usb-c-connector) and chain this together. This
way HPD changes in the connector will propagate to the DisplayPort
driver.
The connector bridge is resolved lazily, as the TCPM is expected to be
able to resolve the typec mux and switch at probe time, so the QMP combo
phy will probe before the TCPM.
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-7-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The data lanes of the QMP PHY is swapped in order to handle changing
orientation of the USB Type-C cable. Register a typec_switch device to
allow a TCPM to configure the orientation.
The newly introduced orientation variable is adjusted based on the
request, and the initialized components are brought down and up again.
To keep track of what parts needs to be cycled new variables to keep
track of the individual init_count is introduced.
Both the USB and the DisplayPort altmode signals are properly switched.
For DisplayPort the controller will after the TCPM having established
orientation power on the PHY, so this is not done implicitly, but for
USB the PHY typically is kept initialized across the switch, and must
therefore then be reinitialized.
This is based on initial work by Wesley Cheng.
Link: https://lore.kernel.org/r/20201009082843.28503-3-wcheng@codeaurora.org/
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-6-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In multiple places throughout the driver code has been written in
prepration for handling of orientation switching.
Introduce a typec_orientation in qmp_combo and fill out the various
"placeholders" with the associated logic. By initializing the
orientation to "normal" this change has no functional impact, but
reduces the size of the upcoming introduction of dynamic orientation
switching.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-5-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The phy core ensures mutual exclusion across the ops for a given phy,
but the upcoming introduction of USB Type-C orientation switching might
race with the DisplayPort phy operations. So extend the mutual exclusion
to cover the remaining ops as well, to avoid concurrent reconfiguration
of the hardware.
Reported-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-4-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
With the upcoming introduction of USB Type-C orientation switching the
region of mutual exclusion needs to be extended to cover both the common
init/exit as well as the individual functions.
So move the phy_mutex one step up the stack.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-3-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The init counter is not decremented on initialisation errors, which
prevents retrying initialisation and can lead to the runtime suspend
callback attempting to disable resources that have never been enabled.
Add the missing decrement on initialisation errors so that the counter
reflects the state of the device.
Fixes: e78f3d15e115 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Cc: stable@vger.kernel.org # 4.12
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230502103810.12061-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The qmp_combo_offsets_v3 table is already used for v3 and v4 PHYs. Reuse
it for v6 too, dropping the separate qmp_combo_offsets_v6.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323144726.1614344-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
SM8350 and SM8450 use qmp_combo_offsets_v3 table, which doesn't have
PCS_USB offset. Add the usb3_pcs_usb entry to program correct registers
while setting up sm8350 and sm8450 USB+DP combo PHYs.
Fixes: 05bd18348b88 ("phy: qcom-qmp-combo: Add config for SM6350")
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323144726.1614344-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
