| Age | Commit message (Collapse) | Author |
|---|
|
No longer access chan with hard-code RTW89_CHANCTX_X whenever possible.
Instead, obtain the right chanctx from somewhere and use it in RTL8851B
RFK (RF calibration) related code.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240819091724.33730-3-pkshih@realtek.com
|
|
LCK is short for LC Tank calibration. To keep RF performance, do this
calibration if difference of thermal value is over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-4-pkshih@realtek.com
|
|
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.
To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-4-pkshih@realtek.com
|
|
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-3-pkshih@realtek.com
|
|
RX DCK is receiver DC calibration. With this calibration, we have proper
DC offset to reflect correct received signal strength indicator. Do this
calibration when bringing up interface and going to run on AP channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-2-pkshih@realtek.com
|
|
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-6-pkshih@realtek.com
|
|
DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output good quality signals.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-5-pkshih@realtek.com
|
|
RCK is synchronize RC calibration. Driver triggers this calibration and
sets the result to register. This calibration is needed once when interface
is going to up.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-4-pkshih@realtek.com
|
|
Automatic amplitude control calibration (AACK) is the calibration to ensure
the oscillator is biased for a constant output amplitude. We do this
calibration if card does power on.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-3-pkshih@realtek.com
|
|
Add to set RF registers according to the channel we want to switch. The
callers will be added afterward.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-2-pkshih@realtek.com
|
