| Age | Commit message (Collapse) | Author |
|---|
|
The PTP_CMD_CTL is a self clearing register which controls the PTP clock
values. In the current implementation driver waits for a duration of 20
sec in case of HW failure to clear the PTP_CMD_CTL register bit. This
timeout of 20 sec is very long to recognize a HW failure, as it is
typically cleared in one clock(<16ns). Hence reducing the timeout to 1 sec
would be sufficient to conclude if there is any HW failure observed. The
usleep_range will sleep somewhere between 1 msec to 20 msec for each
iteration. By setting the PTP_CMD_CTL_TIMEOUT_CNT to 50 the max timeout
is extended to 1 sec.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240502050300.38689-1-rengarajan.s@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for PTP-IO Event Output (Periodic Output - perout) for
PCI11010/PCI11414 chips
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PTP-IOs block provides for time stamping PTP-IO input events.
PTP-IOs are numbered from 0 to 11.
When a PTP-IO is enabled by the corresponding bit in the PTP-IO
Capture Configuration Register, a rising or falling edge,
respectively, will capture the 1588 Local Time Counter
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LAN743x Ethernet controller provides two independent PTP event
channels. Each one can be used to generate a periodic output from
the PTP clock. The output can be routed to any one of the available
GPIO pins on the device.
The PTP clock API can now be used to:
- select any LAN743x GPIO pin to function as a periodic output
- select either LAN743x PTP event channel to generate the output
The LAN7430 has 4 GPIO pins that are multiplexed with its internal
PHY LED control signals. A pin assigned to the LED control function
will be assigned to the GPIO function if selected for PTP periodic
output.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Building without CONFIG_PTP_1588_CLOCK results in multiple failures,
this was obviously not well tested:
drivers/net/ethernet/microchip/lan743x_ptp.c: In function 'lan743x_ptp_isr':
drivers/net/ethernet/microchip/lan743x_ptp.c:781:28: error: 'struct lan743x_ptp' has no member named 'ptp_clock'; did you mean 'tx_ts_lock'?
ptp_schedule_worker(ptp->ptp_clock, 0);
^~~~~~~~~
tx_ts_lock
drivers/net/ethernet/microchip/lan743x_ptp.c: In function 'lan743x_ptp_open':
drivers/net/ethernet/microchip/lan743x_ptp.c:879:6: error: unused variable 'ret' [-Werror=unused-variable]
int ret = -ENODEV;
^~~
At top level:
drivers/net/ethernet/microchip/lan743x_ptp.c:63:13: error: 'lan743x_ptp_tx_ts_enqueue_ts' defined but not used [-Werror=unused-function]
static void lan743x_ptp_tx_ts_enqueue_ts(struct lan743x_adapter *adapter,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
drivers/net/ethernet/microchip/lan743x_ethtool.c: In function 'lan743x_ethtool_get_ts_info':
drivers/net/ethernet/microchip/lan743x_ethtool.c:558:19: error: 'struct lan743x_ptp' has no member named 'ptp_clock'; did you mean 'tx_ts_lock'?
Those #ifdef checks are hard to get right, replace them all with
IS_ENABLED() checks that leave the same code visible to the compiler
but let it optimize out the unused bits based on the configuration.
Fixes: 07624df1c9ef ("lan743x: lan743x: Add PTP support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PTP support includes:
Ingress, and egress timestamping.
One step timestamping available.
PTP clock support.
Periodic output support.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
