| Age | Commit message (Collapse) | Author |
|---|
|
Phylink already handles most of the pieces necessary for configuring
autonegotation. With that being the case we can add support for
getting/setting pause now by just passing through the ethtool call to the
phylink code.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/175028448974.625704.14427543910503058114.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This change adds some basic support for reporting the current link config
to the user via ethtool. Currently the main components reported are the
carrier status, link speed, and FEC.
For now we are handling the FEC directly as phylink doesn't have support
for it. The plan is to work on incorporating FEC support into phylink and
eventually adding the ability for us to set the FEC configuration through
phylink itself.
In addition as we don't yet have SFP or PHY support the listed modes
supported are including ones not supported by the media we are attached to.
That will hopefully be addressed once we can get the QSFP modules
supported.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://patch.msgid.link/175028448275.625704.60592644122010798.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The fbnic driver was using the XLGMII link mode to enable phylink, however
that mode wasn't the correct one to use as the NIC doesn't actually use
XLGMII, it is using a combinations of 25G, 50G, and 100G interface modes
and configuring those via pins exposed on the PCS, MAC, and PHY interfaces.
To more accurately reflect that we should drop the uxe of XGMII and XLGMII
and instead use the correct interface types.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://patch.msgid.link/175028447568.625704.17971496887030109107.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The way we were using "link_mode" was really more to describe the interface
between the attachment unit interface(s) we were using on the device.
Specifically the AUI is describing the modulation and the number of lanes
we are using. So we can simplify this by replacing link_mode with aui.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://patch.msgid.link/175028446219.625704.8050098629750896117.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There were several issues in the way we were handling the link info coming
from firmware.
First is the fact that we were carrying around "AUTO" flags to indicate
that we needed to populate the values. We can just drop this and assume
that we will always be populating the settings from firmware. With this we
can also clean up the masking as the "AUTO" flags were just there to be
stripped anyway.
Second since we are getting rid of the "AUTO" setting we still need a way
to report that the link is not configured. We convert the link_mode "AUTO"
to "UNKNOWN" to do this. With this we can avoid reporting link up in the
phylink_pcs_get_state call as we will just set link to 0 and return without
updating the link speed. This is preferred versus the driver just forcing
50G which makes it harder to recover when the FW does start providing valid
settings.
With this the plan is to eventually replace the link_mode we use with the
interface_mode from phylink for all intents and purposes and have the two
be interchangeable. At that point we can convert the FW provided settings
over to something closer to link partner settings and give phylink greater
control of the interface allowing for user override of the settings and an
asynchronous setup of the link versus having to pull early settings from
firmware.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://patch.msgid.link/175028445548.625704.1367708155813490215.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As all PCS are using the neg_mode parameter rather than the legacy
an_mode, remove the ability to use the legacy an_mode. We remove the
tests in the phylink code, unconditionally passing the PCS neg_mode
parameter to PCS methods, and remove setting the flag from drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tidPn-0040hd-2R@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pass the current neg_mode into the .pcs_get_state() method. Update all
users of phylink PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGeT-000Et3-4L@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add basic support for detecting the link and reporting it at the netdev
layer. For now we will just use the values reporeted by the firmware as the
link configuration and assume that is the current configuration of the MAC
and PCS.
With this we start the stubbing out of the phylink interface that will be
used to provide the configuration interface for ethtool in a future patch
set.
The phylink interface isn't an exact fit. As such we are currently working
around several issues in this patch set that we plan to address in the
future such as:
1. Support for FEC
2. Support for multiple lanes to handle 50GbaseR2 vs 50GbaseR1
3. Support for BMC
CC: Russell King <linux@armlinux.org.uk>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://patch.msgid.link/172079939835.1778861.5964790909718481811.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
