summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel/e1000e/ich8lan.c
AgeCommit message (Collapse)Author
2013-03-08e1000e: cleanup PARENTHESIS_ALIGNMENT checkpatch checksBruce Allan
CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-03-08e1000e: cleanup SPACING checkpatch errors and warningsBruce Allan
ERROR:SPACING: spaces prohibited around that ':' (ctx:WxV) ERROR:SPACING: need consistent spacing around '-' (ctx:WxV) ERROR:SPACING: space required after that ',' (ctx:VxV) ERROR:SPACING: spaces required around that '=' (ctx:VxV) WARNING:SPACING: missing space after enum definition and some similar spacing issues not reported by checkpatch. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-03-08e1000e: cleanup CODE_INDENT checkpatch errorsBruce Allan
ERROR:CODE_INDENT: code indent should use tabs where possible Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-03-05e1000e: workaround DMA unit hang on I218Bruce Allan
At 1000Mbps link speed, one of the MAC's internal clocks can be stopped for up to 4us when entering K1 (a power mode of the MAC-PHY interconnect). If the MAC is waiting for completion indications for 2 DMA write requests into Host memory (e.g. descriptor writeback or Rx packet writing) and the indications occur while the clock is stopped, both indications will be missed by the MAC causing the MAC to wait for the completion indications and be unable to generate further DMA write requests. This results in an apparent hardware hang. Work-around the issue by disabling the de-assertion of the clock request when 1000Mbps link is acquired (K1 must be disabled while doing this). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-05e1000e: cleanup checkpatch braces checksBruce Allan
Resolve the following strict checkpatch checks: CHECK:BRACES: Blank lines aren't necessary after an open brace '{' CHECK:BRACES: Blank lines aren't necessary before a close brace '}' CHECK:BRACES: braces {} should be used on all arms of this statement Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-04e1000e: cosmetic move of #defines and prototypes to the new ich8lan.hBruce Allan
Move #defines and function prototypes specific to the ICH/PCH family of devices (ICH8/82562, ICH8/82566, ICH8/82567, ICH9/82562, ICH9/82566, ICH9/82567, ICH10/82567, 82577, 82578, 82579, I217, I218) to the new ich8lan.h header file (the convention for Intel wired ethernet drivers is to use the name of the first device in the family for related file and function names). These defines and function prototypes can be used by other files in the driver and moving them to the ICH/PCH-family-specific file makes it clearer to which devices they are applicable. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-31e1000e: use generic IEEE MII definitionsBruce Allan
For standard IEEE MII-compatible transceivers, the kernel has generic register and bit definitions. Use those instead of redundant local defines. Do not replace references of MII_CR_SPEED_10 with BMCR_SPEED10 (0x0000) when it is not necessary (i.e. when it is bitwise OR'ed with another value). Some whitespace issues in the surrounding context of the above changes are also cleaned up. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-31e1000e: resolve -Wunused-parameter compile warningsBruce Allan
Remove the unused parameter when possible, otherwise use __always_unused attribute. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-31e1000e: cleanup some whitespace and indentation issuesBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: correct maximum frame size on 82579Bruce Allan
The largest jumbo frame supported by the 82579 hardware is 9018. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: cleanup: rename e1000_get_cfg_done()Bruce Allan
In keeping with the e1000e driver function naming convention, the subject function is renamed to indicate it is generic, i.e. it is applicable to more than just a single MAC family (e.g. 80003es2lan, 82571, ich8lan). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: cleanup: do not assign a variable a value when not necessaryBruce Allan
Static analysis with cppcheck has shown a few instances of a variable being reassigned a value before the old one has been used. None of these ever require the old value to be used so remove the old values. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: do not ignore variables which get set a valueBruce Allan
Static analysis with cppcheck has shown a few instances of a variable which is assigned a value that is never used. A number of these are the return status of various driver function calls which should be passed back to the caller of the current function. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: cleanup: remove unnecessary function prototypesBruce Allan
...and cleanup some whitespace in other prototypes. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: fix PHY init workarounds for i217/i218Bruce Allan
Toggling the LANPHYPC Value bit cycles the power on the PHY and sets it back to power-on defaults. This includes setting it's MAC-PHY messaging mode to use the PCIe-like interconnect, so the MAC must also be set back from SMBus mode to PCIe mode otherwise the PHY can be inaccessible. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: correct maximum frame size on i217/i218Bruce Allan
The largest jumbo frame supported by the i217 and i218 hardware is 9018. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: update copyright dateBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: prevent hardware from automatically configuring PHY on I217/I218Bruce Allan
As done with the previous generation managed 82579, prevent the PHY from being put into an unknown state by blocking the hardware from automatically configuring the PHY as done with the previous generation managed 82579. Instead, the driver should configure the PHY with contents of the EEPROM image. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-27e1000e: enable ECC on I217/I218 to catch packet buffer memory errorsBruce Allan
In rare instances, memory errors have been detected in the internal packet buffer memory on I217/I218 when stressed under certain environmental conditions. Enable Error Correcting Code (ECC) in hardware to catch both correctable and uncorrectable errors. Correctable errors will be handled by the hardware. Uncorrectable errors in the packet buffer will cause the packet to be received with an error indication in the buffer descriptor causing the packet to be discarded. If the uncorrectable error is in the descriptor itself, the hardware will stop and interrupt the driver indicating the error. The driver will then reset the hardware in order to clear the error and restart. Both types of errors will be accounted for in statistics counters. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-18e1000e: add support for hardware timestamping on some devicesBruce Allan
On 82574, 82583, 82579, I217 and I218 add support for hardware time stamping of all or no Rx packets and Tx packets which have the SKBTX_HW_TSTAMP flag set. Update the .get_ts_info ethtool operation to report the supported time stamping modes, and enable and disable hardware time stamping with the SIOCSHWTSTAMP ioctl. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-18e1000e: add ethtool .get_eee/.set_eeeBruce Allan
Add the ability to query and set Energy Efficient Ethernet parameters via ethtool for applicable devices. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-15e1000e: add missing bailout on errorBruce Allan
...discovered during code inspection. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-15e1000e: fix enabling of EEE on 82579 and I217Bruce Allan
Energy Efficient Ethernet on 82579 and I217 should only be enabled if not disabled by the user, if the link is full duplex and the link partner has similar EEE capabilities (stored in different EMI registers on the two different parts). After enabling EEE, read the IEEE MMD register 3.1 (which is also stored in different EMI registers on the two different parts) to clear the count of received Tx/Rx LPI indications. Also, rename I217_EEE_100_SUPPORTED to I82579_EEE_100_SUPPORTED to indicate the bit is valid starting with I82579 (released before I217). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-15e1000e: 82577: workaround for link drop issueBruce Allan
When connected to certain switches, the 82577 PHY might drop link unexpectedly. Work around the issue by setting the Mean Square Error higher than the hardware default. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-15e1000e: helper functions for accessing EMI registersBruce Allan
The Extended Management Interface (EMI) registers are accessed by first writing the EMI register offset to the EMI_ADDR regiter and then either reading or writing the data to/from the EMI_DATA register. Add helper functions for performing these steps and convert existing EMI register accesses accordingly. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-01-15e1000e: Invalid Image CSUM bit changed for I217Bruce Allan
On I217, the bit that indicates an invalid EEPROM (NVM) image checksum has changed from previous ICH/PCH LOMs. When validating the EEPROM checksum, check the appropriate bit on different devices. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-12-01e1000e: cosmetic cleanup of commentsBruce Allan
Update comments to conform to the preferred style for networking code as described in ./Documentation/CodingStyle and checked for in the recently added checkpatch NETWORKING_BLOCK_COMMENT_STYLE test. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-07-14e1000e: fix test for PHY being accessible on 82577/8/9 and I217Bruce Allan
Occasionally, the PHY can be initially inaccessible when the first read of a PHY register, e.g. PHY_ID1, happens (signified by the returned value 0xFFFF) but subsequent accesses of the PHY work as expected. Add a retry counter similar to how it is done in the generic e1000_get_phy_id(). Also, when the PHY is completely inaccessible (i.e. when subsequent reads of the PHY_IDx registers returns all F's) and the MDIO access mode must be set to slow before attempting to read the PHY ID again, the functions that do these latter two actions expect the SW/FW/HW semaphore is not already set so the semaphore must be released before and re-acquired after calling them otherwise there is an unnecessarily inordinate amount of delay during device initialization. Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-06-02e1000e: fix Rapid Start Technology support for i217Bruce Allan
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY register greater than the maximum allowed by the latter macro, and fix a typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan. Also for clarity, rename a few defines as bit definitions instead of masks. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-05-04e1000e: initial support for i217Bruce Allan
i217 is the next-generation LOM that will be available on systems with the Lynx Point Platform Controller Hub (PCH) chipset from Intel. This patch provides the initial support for the device. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-05-03e1000e: Driver workaround for IPv6 Header Extension Erratum.Matthew Vick
Previously, IPv6 extension header parsing was disabled for all devices supported by e1000e when using packet split mode. However, as per a silicon errata, only certain devices need this restriction and will need to disable IPv6 extension header parsing for all modes. Signed-off-by: Matthew Vick <matthew.vick@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-05-03e1000e: cleanup long [read|write]_reg_locked PHY ops function pointersBruce Allan
Calling the locked versions of the read/write PHY ops function pointers often produces excessively long lines. Shorten these as is done with the non-locked versions of the PHY register read/write functions. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-05-02e1000e: fix .ndo_set_rx_mode for 82579Bruce Allan
Secondary unicast and multicast addresses are added to the Receive Address registers (RAR) for most parts supported by the driver. For 82579, there is only one actual RAR and a number of Shared Receive Address registers (SHRAR) that are shared among the driver and f/w which can be reserved and write-protected by the f/w. On this device, use the SHRARs that are not taken by f/w for the additional addresses. Add a MAC ops function pointer infrastructure (similar to other MAC operations in the driver) for setting RARs, introduce a new rar_set function for 82579 and convert the existing code that sets RARs on other devices to a generic rar_set function. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-05-02e1000e: PHY initialization flow changes for 82577/8/9Bruce Allan
The PHY initialization flows and assorted workarounds for 82577/8/9 done during driver load and resume from Sx should be the same yet they are not. Combine the current flows/workarounds into a common set of functions that are called during the different code paths. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-05-02e1000e: workaround EEPROM configuration change on 82579Bruce Allan
An update to the EEPROM on 82579 will extend a delay in hardware to fix an issue with WoL not working after a G3->S5 transition which is unrelated to the driver. However, this extended delay conflicts with nominal operation of the device when it is initialized by the driver and after every reset of the hardware (i.e. the driver starts configuring the device before the hardware is done with it's own configuration work). The workaround for when the driver is in control of the device is to tell the hardware after every reset the configuration delay should be the original shorter one. Some pre-existing variables are renamed generically to be re-used with new register accesses. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-27e1000e: 82579 packet drop workaroundBruce Allan
In K1 mode (a MAC/PHY interconnect power mode), the 82579 device shuts down the Phase Lock Loop (PLL) of the interconnect to save power. When the PLL starts working, the 82579 device may start to transfer the packet through the interconnect before it is fully functional causing packet drops. This workaround disables shutting down the PLL in K1 mode for 1G link speed. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/ethernet/atheros/atlx/atl1.c drivers/net/ethernet/atheros/atlx/atl1.h Resolved a conflict between a DMA error bug fix and NAPI support changes in the atl1 driver. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-14e1000e: cleanup boolean logicBruce Allan
Replace occurrences of 'if (<bool expr> == <1|0>)' with 'if ([!]<bool expr>)' Replace occurrences of '<bool var> = (<non-bool expr>) ? true : false' with '<bool var> = <non-bool expr>'. Replace occurrence of '<bool var> = <non-bool expr>' with '<bool var> = !!<non-bool expr>' While the latter replacement is not really necessary, it is done here for consistency and clarity. No functional changes. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-14e1000e: issues in Sx on 82577/8/9Bruce Allan
A workaround was previously put in the driver to reset the device when transitioning to Sx in order to activate the changed settings of the PHY OEM bits (Low Power Link Up, or LPLU, and GbE disable configuration) for 82577/8/9 devices. After further review, it was found such a reset can cause the 82579 to confuse which version of 82579 it actually is and broke LPLU on all 82577/8/9 devices. The workaround during an S0->Sx transition on 82579 (instead of resetting the PHY) is to restart auto-negotiation after the OEM bits are configured; the restart of auto-negotiation activates the new OEM bits as does the reset. With 82577/8, the reset is changed to a generic reset which fixes the LPLU bits getting set wrong. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-02-29e1000e: cleanup whitespace and indentationBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-02-24e1000e: rename e1000e_reload_nvm() and call as function pointerBruce Allan
Rename e1000e_reload_nvm() to e1000e_reload_nvm_generic() to signify the function is used for more than one MAC-family type, and set and use it as a MAC ops function pointer to be consistent with the driver design. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-02-24e1000e: rename e1000e_config_collision_dist() and call as function pointerBruce Allan
Rename e1000e_config_collision_dist() to e1000e_config_collision_dist_generic() to signify the function is used for more than one MAC-family type, and set and use it as a MAC ops function pointer to be consistent with the driver design. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-02-24e1000e: comment correction in e1000e_set_kmrn_lock_loss_workaround_ich8lanBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-02-24e1000e: cleanup calls to setup_physical_interface function pointerBruce Allan
Call the MAC ops setup_physical_interface function pointer instead of the MAC-family-specific function to conform to the rest of the driver design. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-02-24e1000e: cleanup use of check_reset_block function pointerBruce Allan
Replace e1000_check_reset_block() inline function with calls to the PHY ops check_reset_block function pointer. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-02-24e1000e: cleanup: rename e1000e_setup_link() and call as function pointerBruce Allan
Rename e1000e_setup_link() to e1000e_setup_link_generic() to signify the function is used for more than one MAC-family type. The 82571-family has a custom setup_link function which also calls the generic function. The ich8lan-family has a custom function which should just be called via the function pointer. The 80003es2lan-family just uses the generic function. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-02-24e1000e: cleanup: rename e1000e_id_led_init() and call as function pointerBruce Allan
Rename e1000e_id_led_init() to e1000e_id_led_init_generic() to signify the function is used for more than one MAC-family type. For the ich8lan MAC family, some MACs use the generic function and others use the function e1000_id_led_init_pchlan(). In all cases where e1000e_id_led_init() was called directly, change to call the function pointer to be consistent with the driver design. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-02-13e1000e: cleanup goto statements to exit points without common workBruce Allan
Per ./Documentation/CodingStyle, goto statements are acceptable for the centralized exiting of functions when there are multiple exit points which share common work such as cleanup. When no common work is required for multiple exit points, the function should just return at these exit points instead of doing an unnecessary jump to a centralized return. This patch cleans up the inappropriate use of goto statements, and removes unnecessary variables (or move to a smaller scope) where possible as a result of the cleanups. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-02-13e1000e: potentially incorrect return for e1000_init_hw_ich8lanBruce Allan
In the unlikely event that e1000_setup_link_ich8lan() returns an error, the returned error code value is not propagated to the caller of e1000_init_hw_ich8lan(). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-02-13e1000e: cleanup: minor whitespace addition (insert blank line separator)Bruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-02 20:59:23 +0000