| Age | Commit message (Collapse) | Author |
|---|
|
Fix the handling of err_wq_init and err_reg_netdev paths in
enetc4_pf_netdev_create() function.
Fixes: 6c5bafba347b ("net: enetc: add MAC filtering for i.MX95 ENETC PF")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250516052734.3624191-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add internal loopback support for i.MX95 ENETC PF, the default loopback
mode is MAC level loopback, the MAC Tx data is looped back onto the Rx.
The MAC interface runs at a fixed 1:8 ratio of NETC clock in MAC-level
loopback mode, with no dependency on Tx clock.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250506080735.3444381-15-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the offsets of the VLAN hash filter registers of ENETC v4 are
different from ENETC v1. Therefore, enetc_set_si_vlan_ht_filter() is
added to set the correct VLAN hash filter based on the SI ID and ENETC
revision, so that ENETC v4 PF driver can reuse enetc_vlan_rx_add_vid()
and enetc_vlan_rx_del_vid(). In addition, the VLAN promiscuous mode will
be enabled if VLAN filtering is disabled, which means that PF qualifies
for reception of all VLAN tags.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250506080735.3444381-14-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Compared with LS1028A, there are two main differences: first, i.MX95
ENETC uses NTMP 2.0 to manage the RSS table, and second, the offset
of the RSS Key registers is different. Some modifications have been
made in the previous patches based on these differences to ensure that
the relevant interfaces are compatible with i.MX95. So it's time to
add RSS support to i.MX95 ENETC PF.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250506080735.3444381-9-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the offset of the RSS key registers of i.MX95 ENETC is different
from that of LS1028A, so add enetc_get_rss_key_base() to get the base
offset for the different chips, so that enetc_set_rss_key() can be
reused for this trivial thing.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250506080735.3444381-8-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ENETC's MAC filter consists of hash MAC filter and exact MAC filter.
Hash MAC filter is a 64-bit entry hash table consisting of two 32-bit
registers. Exact MAC filter is implemented by configuring MAC address
filter table through command BD ring. The table is stored in ENETC's
internal memory and needs to be read through command BD ring. In order
to facilitate debugging, added a debugfs interface to get the relevant
information about MAC filter.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250506080735.3444381-6-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The i.MX95 ENETC supports both MAC hash filter and MAC exact filter. MAC
hash filter is implenented through a 64-bit hash table to match against
the hashed addresses, PF and VFs each have two MAC hash tables, one is
for unicast and the other one is for multicast. But MAC exact filter is
shared between SIs (PF and VFs), each table entry contains a MAC address
that may be unicast or multicast and the entry also contains an SI bitmap
field that indicates for which SIs the entry is valid.
For i.MX95 ENETC, MAC exact filter only has 4 entries. According to the
observation of the system default network configuration, the MAC filter
will be configured with multiple multicast addresses, so MAC exact filter
does not have enough entries to implement multicast filtering. Therefore,
the current MAC exact filter is only used for unicast filtering. If the
number of unicast addresses exceeds 4, then MAC hash filter is used.
Note that both MAC hash filter and MAC exact filter can only be accessed
by PF, VFs can notify PF to set its corresponding MAC filter through the
mailbox mechanism of ENETC. But currently MAC filter is only added for
i.MX95 ENETC PF. The MAC filter support of ENETC VFs will be supported in
subsequent patches.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250506080735.3444381-5-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The command BD ring is used to configure functionality where the
underlying resources may be shared between different entities or being
too large to configure using direct registers (such as lookup tables).
Because the command BD and table formats of i.MX95 and LS1028A are very
different, the software processing logic is also different. So add
enetc4_setup_cbdr() and enetc4_teardown_cbdr() for ENETC v4 drivers.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250506080735.3444381-3-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the ENETC v4 driver has not added the MAC merge layer support
in the upstream, so the mm_lock is not initialized and used, so remove
the mm_lock from the driver.
Fixes: 99100d0d9922 ("net: enetc: add preliminary support for i.MX95 ENETC PF")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-8-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The enetc4_link_init() is called when the PF driver probes to create
phylink and MDIO bus, but we forgot to call enetc4_link_deinit() to
free the phylink and MDIO bus when the driver was unbound. so add
missing enetc4_link_deinit() to enetc4_pf_netdev_destroy().
Fixes: 99100d0d9922 ("net: enetc: add preliminary support for i.MX95 ENETC PF")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-7-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20241105093125.1087202-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The i.MX95 ENETC has been upgraded to revision 4.1, which is different
from the LS1028A ENETC (revision 1.0) except for the SI part. Therefore,
the fsl-enetc driver is incompatible with i.MX95 ENETC PF. So add new
nxp-enetc4 driver to support i.MX95 ENETC PF, and this driver will be
used to support the ENETC PF with major revision 4 for other SoCs in the
future.
Currently, the nxp-enetc4 driver only supports basic transmission feature
for i.MX95 ENETC PF, the more basic and advanced features will be added
in the subsequent patches. In addition, PCS support has not been added
yet, so 10G ENETC (ENETC instance 2) is not supported now.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
