| Age | Commit message (Collapse) | Author |
|---|
|
We had a number of short comings:
- EEE must be re-evaluated whenever the state machine detects a link
change as wight be switching from a link partner with EEE
enabled/disabled
- tx_lpi_enabled controls whether EEE should be enabled/disabled for the
transmit path, which applies to the TBUF block
- We do not need to forcibly enable EEE upon system resume, as the PHY
state machine will trigger a link event that will do that, too
Fixes: 6ef398ea60d9 ("net: bcmgenet: add EEE support")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230606214348.2408018-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 16nm internal EPHY that is present in 7712 is actually a 16nm
Gigabit PHY which has been forced to operate in 10/100 mode. Its
controls are therefore via the EXT_GPHY_CTRL registers and not via the
EXT_EPHY_CTRL which are used for all GENETv5 adapters. Add a match on
the 7712 compatible string to allow that differentiation to happen.
On previous GENETv4 chips the EXT_CFG_IDDQ_GLOBAL_PWR bit was cleared by
default, but this is not the case with this chip, so we need to make
sure we clear it to power on the EPHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit extends the supported ethtool operations to allow MAC
level flow control to be configured for the bcmgenet driver.
The ethtool utility can be used to change the configuration of
auto-negotiated symmetric and asymmetric modes as well as manually
configuring support for RX and TX Pause frames individually.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY state machine has been fixed to only call the adjust_link
callback when the link state has changed. Therefore the old link
state variables are no longer needed to detect a change in link
state.
This commit effectively reverts
commit 5ad6e6c50899 ("net: bcmgenet: improve bcmgenet_mii_setup()")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
UniMAC is integrated into multiple Broadcom's Ethernet controllers so
use a shared header file for it and avoid some code duplication.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Link: https://lore.kernel.org/r/20210107180051.1542-2-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Hardware Filter Block RAM may not be preserved when the GENET
block is reset during a deep sleep, so it is not sufficient to
only backup and restore the enables.
This commit clears out the HFB block and reprograms the rxnfc
rules when the system resumes from a suspended state. To support
this the bcmgenet_hfb_create_rxnfc_filter() function is modified
to access the register space directly so that it can't fail due
to memory allocation issues.
Fixes: f50932cca632 ("net: bcmgenet: add WAKE_FILTER support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The side band interrupt service routine is not available on chips
like 7211, or rather, it does not permit the signaling of wake-up
events due to the complex interrupt hierarchy.
Move the wake-up event accounting into a .resume_noirq function,
account for possible wake-up events and clear the MPD/HFB interrupts
from there, while leaving the hardware untouched until the resume
function proceeds with doing its usual business.
Because bcmgenet_wol_power_down_cfg() now enables the MPD and HFB
interrupts, it is invoked by a .suspend_noirq function to prevent
the servicing of interrupts after the clocks have been disabled.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit enables driver support for ethtool commands of this form:
ethtool -N|-U|--config-nfc|--config-ntuple devname
flow-type ether|ip4
[src xx:yy:zz:aa:bb:cc [m xx:yy:zz:aa:bb:cc]]
[dst xx:yy:zz:aa:bb:cc [m xx:yy:zz:aa:bb:cc]] [proto N [m N]]
[src-ip x.x.x.x [m x.x.x.x]] [dst-ip x.x.x.x [m x.x.x.x]] [tos N [m N]]
[l4proto N [m N]] [src-port N [m N]] [dst-port N [m N]] [spi N [m N]]
[l4data N [m N]] [vlan-etype N [m N]] [vlan N [m N]]
[dst-mac xx:yy:zz:aa:bb:cc [m xx:yy:zz:aa:bb:cc]] [action 0] [loc N] |
delete N
Since there is only one Rx Ring in this implementation action 0 behaves no
differently from not specifying a rule.
The rules can be seen with ethtool commands of this form:
ethtool -n|-u|--show-nfc|--show-ntuple devname [rule N]
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GENET_POWER_WOL_MAGIC power up and power down code configures
the device for WoL when suspending and disables the WoL logic when
resuming. It makes sense that this code should also manage the WoL
clocking.
This commit consolidates the logic and moves it earlier in the
resume sequence.
Since the clock is now only enabled if WoL is successfully entered
the wol_active flag is introduced to track that state to keep the
clock enables and disables balanced in case a suspend is aborted.
The MPD_EN hardware bit can't be used because it can be cleared
when the MAC is reset by a deep sleep.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Broadcom STB chips support a deep sleep mode where all register contents
are lost. Because we were stashing the MagicPacket password into some of
these registers a suspend into that deep sleep then a resumption would
not lead to being able to wake-up from MagicPacket with password again.
Fix this by keeping a software copy of the password and program it
during suspend.
Fixes: c51de7f3976b ("net: bcmgenet: add Wake-on-LAN support code")
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware offloading of the NETIF_F_HW_CSUM and NETIF_F_RXCSUM
features requires the use of Transmit Status Blocks before transmit
frame data and Receive Status Blocks before receive frame data to
carry the checksum information.
Unfortunately, these status blocks are currently only enabled when
the NETIF_F_HW_CSUM feature is enabled. As a result NETIF_F_RXCSUM
will not actually be offloaded to the hardware unless both it and
NETIF_F_HW_CSUM are enabled. Fortunately, that is the default
configuration.
This commit addresses this issue by always enabling the use of
status blocks on both transmit and receive frames. Further, it
replaces the use of a dedicated flag within the driver private
data structure with direct use of the netdev features flags.
Fixes: 810155397890 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When inserting the TSB, keep track of how many times we had to do
it and if there was a failure in doing so, this helps profile the
driver for possibly incorrect headroom settings.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit updates the Rx checksum offload behavior of the driver
to use the more generic CHECKSUM_COMPLETE method that supports all
protocols over the CHECKSUM_UNNECESSARY method that only applies
to some protocols known by the hardware.
This behavior is perceived to be superior.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BCM2711 needs a different maximum DMA burst length. If not set
accordingly a timeout in the transmit queue happens and no package
can be sent. So use the new compatible to derive this value.
Until now the GENET HW version was used as the platform identifier.
This doesn't work with SoC-specific modifications, so introduce a proper
platform data structure.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 1f515486275a08a17a2c806b844cca18f7de5b34.
This commit improved the chances of the umac resetting cleanly by
ensuring that the PHY was restored to its normal operation prior
to resetting the umac. However, there were still cases when the
PHY might not be driving a Tx clock to the umac during this window
(e.g. when the PHY detects no link).
The previous commit now ensures that the unimac receives clocks
from the MAC during its reset window so this commit is no longer
needed. This commit also has an unintended negative impact on the
MDIO performance of the UniMAC MDIO interface because it is used
before the MDIO interrupts are reenabled, so it should be removed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It turns out that the "Workaround for putting the PHY in IDDQ mode"
used by the internal EPHYs on 40nm Set-Top Box chips when powering
down puts the interface to the GENET MAC in a state that can cause
subsequent MAC resets to be incomplete.
Rather than restore the forced soft reset when powering up internal
PHYs, this commit moves the invocation of phy_init_hw earlier in
the MAC initialization sequence to just before the MAC reset in the
open and resume functions. This allows the interface to be stable
and allows the MAC resets to be successful.
The bcmgenet_mii_probe() function is split in two to accommodate
this. The new function bcmgenet_mii_connect() handles the first
half of the functionality before the MAC initialization, and the
bcmgenet_mii_config() function is extended to provide the remaining
PHY configuration following the MAC initialization.
Fixes: 484bfa1507bf ("Revert "net: bcmgenet: Software reset EPHY after power on"")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RGMII_MODE_EN bit value was 0 for GENET versions 1 through 3, and
became 6 for GENET v4 and above, account for that difference.
Fixes: aa09677cba42 ("net: bcmgenet: add MDIO routines")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mamameed says:
====================
Generic DIM
From: Tal Gilboa and Yamin Fridman
Implement net DIM over a generic DIM library, add RDMA DIM
dim.h lib exposes an implementation of the DIM algorithm for
dynamically-tuned interrupt moderation for networking interfaces.
We want a similar functionality for other protocols, which might need to
optimize interrupts differently. Main motivation here is DIM for NVMf
storage protocol.
Current DIM implementation prioritizes reducing interrupt overhead over
latency. Also, in order to reduce DIM's own overhead, the algorithm might
take some time to identify it needs to change profiles. While this is
acceptable for networking, it might not work well on other scenarios.
Here we propose a new structure to DIM. The idea is to allow a slightly
modified functionality without the risk of breaking Net DIM behavior for
netdev. We verified there are no degradations in current DIM behavior with
the modified solution.
Suggested solution:
- Common logic is implemented in lib/dim/dim.c
- Net DIM (existing) logic is implemented in lib/dim/net_dim.c, which uses
the common logic in dim.c
- Any new DIM logic will be implemented in "lib/dim/new_dim.c".
This new implementation will expose modified versions of profiles,
dim_step() and dim_decision().
- DIM API is declared in include/linux/dim.h for all implementations.
Pros for this solution are:
- Zero impact on existing net_dim implementation and usage
- Relatively more code reuse (compared to two separate solutions)
- Increased extensibility
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Moved all logic from dim.h and net_dim.h to dim.c and net_dim.c.
This is both more structurally appealing and would allow to only
expose externally used functions.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Removed 'net' prefix from functions and structs used by external drivers.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When using the fixed PHY with GENET (e.g. MOCA) the PHY link
status can be determined from the internal link status captured
by the MAC. This allows the PHY state machine to use the correct
link state with the fixed PHY even if MAC link event interrupts
are missed when the net device is opened.
Fixes: 8d88c6ebb34c ("net: bcmgenet: enable MoCA link state change detection")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were a number of issues with setting the RX coalescing parameters:
- we would not be preserving values that would have been configured
across close/open calls, instead we would always reset to no timeout
and 1 interrupt per packet, this would also prevent DIM from setting its
default usec/pkts values
- when adaptive RX would be turned on, we woud not be fetching the
default parameters, we would stay with no timeout/1 packet per interrupt
until the estimator kicks in and changes that
- finally disabling adaptive RX coalescing while providing parameters
would not be honored, and we would stay with whatever DIM had previously
determined instead of the user requested parameters
Fixes: 9f4ca05827a2 ("net: bcmgenet: Add support for adaptive RX coalescing")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unlike the moder modern SYSTEMPORT hardware, we do not have a
configurable TDMA timeout, which limits us to implement adaptive RX
interrupt coalescing only. We have each of our RX rings implement a
bcmgenet_net_dim structure which holds an interrupt counter, number of
packets, bytes, and a container for a net_dim instance.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the software reset of the PHY has been removed it is no
longer necessary to retain a private pointer to the phydev for
use when the PHY is detached (which isn't generally safe anyway).
The driver now uses the phydev member attached to the net_device.
For ethtool commands that have a PHY component, an explicit check
is made to prevent accessing an invalid phydev pointer when one
is not attached (e.g. interface is down).
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With commit f7d72996e222 ("net: bcmgenet: enable loopback during
UniMAC sw_reset") it is no longer necessary to force the software
reset of the internal EPHY before resetting the UniMAC to ensure a
clean reset.
Therefore this commit reverts commit 5dbebbb44a6a ("net: bcmgenet:
Software reset EPHY after power on").
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A stray return was added in the macro bcmgenet_##name##_writel where it
should not, drop it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 69d2ea9c7989 ("net: bcmgenet: Use correct I/O accessors")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GENET driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 28b45910ccda ("net: bcmgenet: Remove init parameter
from bcmgenet_mii_config") because in the process of moving from
dev_info() to dev_info_once() we essentially lost the helpful printed
messages once the second instance of the driver is loaded.
dev_info_once() does not actually print the message once per device
instance, but once period.
Fixes: 28b45910ccda ("net: bcmgenet: Remove init parameter from bcmgenet_mii_config")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the GENET driver to register an UniMAC MDIO bus controller for
the GENET internal MDIO bus, update the platform data code to attach the
PHY to the correct MDIO bus controller.
The Device Tree portion of the code is mostly left unmodified since the
lookup/binding is done via phandles and Device Tree nodes which are much
more flexible in locating and binding PHYs to their respective MDIO bus
controllers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the skb is attached to the first control block of a fragmented
skb it is possible that the skb could be freed when reclaiming that
control block before all fragments of the skb have been consumed by
the hardware and unmapped.
This commit introduces first_cb and last_cb pointers to the skb
control block used by the driver to keep track of which transmit
control blocks within a transmit ring are the first and last ones
associated with the skb.
It then splits the bcmgenet_free_cb() function into transmit
(bcmgenet_free_tx_cb) and receive (bcmgenet_free_rx_cb) versions
that can handle the unmapping of dma mapped memory and cleaning up
the corresponding control block structure so that the skb is only
freed after the last associated transmit control block is reclaimed.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__bcmgenet_tx_reclaim() is currently summing TX bytes/packets in a way
that is not SMP friendly, mutliples CPUs could run
__bcmgenet_tx_reclaim() independently and still update stats->tx_bytes
and stats->tx_packets, cloberring the other CPUs statistics.
Fix this by tracking per RX and TX rings the number of bytes, packets,
dropped and errors statistics, and provide a bcmgenet_get_stats()
function which aggregates everything and returns a consistent output.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmgenet.c
net/core/sock.c
Conflicts were overlapping changes in bcmgenet and the
lockdep handling of sockets.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds support for the GENETv5 implementation.
The GENETv5 reports a major version of 6 instead of 5 so compensate
for this when verifying the configuration of the driver. Also the
EPHY revision is now contained in the MDIO registers of the PHY so
the EPHY revision of 0 in GENET_VER_FMT is expected for GENETv5.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a spinlock to ensure that irq0_stat is not unintentionally altered
as the result of preemption. Also removed unserviced irq0 interrupts
and removed irq1_stat since there is no bottom half service for those
interrupts.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The location of the RBUF overflow and error counters has moved between
different version of the GENET MAC. This commit corrects the driver to
read from the correct locations depending on the version of the GENET
MAC.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 62469c76007e ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:
PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)
This was previously fixed by commit 5dbebbb44a6a ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.
Without commit 62469c76007e we would have the following scenario after
an ifconfig down then up sequence:
- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
initialized *before* we get to initialize the UniMAC, this is
critical to ensure the PHY is in a correct state, priv->phydev is
valid, this code executes fine
- second time from bcmgenet_mii_probe(), through the normal
phy_init_hw() call (which arguably could be optimized out)
Everything is fine in that case. With commit 62469c76007e, we would have
the following scenario to happen after an ifconfig down then up
sequence:
- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
NULL
- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
bcmgenet_power_up() to initialize the internal PHY, the NULL check
becomes true, so we do not reset the PHY, yet we keep going on and
initialize the UniMAC, causing MAC activity to occur
- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
too late, the PHY is botched, and causes the above bogus pings/packets
transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Add bytes_compl local variable to __bcmgenet_tx_reclaim() to collect
transmitted bytes. dev->stats updates can then be moved outside the
while-loop. bytes_compl is also needed for future BQL support.
2. When bcmgenet device uses Tx checksum offload, each transmitted skb
gets an extra 64-byte header prepended to it. Before this header is
prepended to the skb, we need to save the skb "wire" length in
GENET_CB(skb)->bytes_sent, so that proper Tx bytes accounting can
be done in __bcmgenet_tx_reclaim().
3. skb->len covers the entire length of skb, whether it is linear or
fragmented. Thus, when we clean the fragments, do not increase
transmitted bytes.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EPHY on GENET v1->v3 is extremely finicky, and will show occasional
failures based on the timing and reset sequence, ranging from duplicate
packets, to extremely high latencies.
Perform an additional software reset, and re-configuration to make sure it is
in a consistent and working state.
Fixes: 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the ethtool rx-frames coalescing parameter which allows
defining the number of RX interrupts per frames received. The RDMA
engine supports a configurable timeout with a resolution of
approximately 8.192 us.
We can no longer enable the BDONE/PDONE interrupts as those would
fire for each packet/buffer received, which would defeat the MBDONE
interrupt purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Configuring the ethtool tx-frames property, which translates into N
packets before a TX interrupt is the simplest configuration scheme
because it requires no locking neither at the softare nor hardware
level, and is completely indepedent from the link speed. Since ethtool
does not allow per-tx queue coalescing parameters, we apply the same
setting to any transmit queue.
We can no longer enable the BDONE/PDONE interrupts as those would fire
for each packet/buffer received, which would defeat the MBDONE interrupt
purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1, but offers
interrupt coalescing when the value is > 1.
Since the HW is configured to generate an interrupt when the ring
becomes emtpy, we have to deny any timeout/timer settings coming from
user-space to indicate we can only generate an interrupt very <N>
packets.
While we are at it, fix the DMA_INTR_THRESHOLD_MASK value which was off
by one bit (0xff vs. 0x1ff).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have reworked the way we perform the PHY initialization, we
no longer need to differentiate between init time vs. non-init time
calls, just use a dev_info_once() print to print the PHY type.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are currently doing a full PHY initialization and even starting the
pHY state machine during bcmgenet_mii_init() which is executed in the
driver's probe function. This is convenient to determine whether we can
attach to a proper PHY device but comes at the expense of spending up to
10ms per MDIO transactions (to reach the waitqueue timeout), which slows
things down.
This also creates a sitaution where we end-up attaching twice to the
PHY, which is not quite correct either.
Fix this by moving bcmgenet_mii_probe() into bcmgenet_open() and update
its error path accordingly.
Avoid printing the message "attached PHY at address 1 [...]" every time
we bring up/down the interface and remove this print since it duplicates
what the PHY driver already does for us.
Fixes: 1c1008c793fa4 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our internal GPHY might be powered off before we attempt scanning the
MDIO bus and bind a driver to it. The way we are currently determining
whether a PHY is internal or not is done *after* we have successfully
matched its driver. If the PHY is powered down, it will not respond to
the MDIO bus, so we will not be able to bind a driver to it.
Our Device Tree for GENET interfaces specifies a "phy-mode" value:
"internal" which tells if this internal uses an internal PHY or not.
If of_get_phy_mode() fails to parse the 'phy-mode' property, do an
additional manual lookup, and if we find "internal" set the
corresponding internal variable accordingly.
Replace all uses of phy_is_internal() with a check against
priv->internal_phy to avoid having to rely on whether or not
priv->phydev is set correctly.
Fixes: 1c1008c793fa4 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are currently issuing multiple PHY resets during a suspend/resume,
first during bcmgenet_power_up() which does a hardware reset, then a
software reset by calling bcmgenet_mii_reset(). This is both unnecessary
and can take as long as 10ms per MDIO transactions while we re-apply
workarounds because we do not yet have MDIO interrupts enabled.
phy_resume() takes care of re-apply our workarounds in case we need any,
and bcmgenet_power_up() does a PHY hardware reset, all of this is more
than enough to guarantee that the PHY operates correctly.
Fixes: 1c1008c793fa4 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All BCM7xxx integrated Gigabit PHYs have an issue in their MDIO
management controller which will make the initial read or write to them
to fail and return 0xffff. This is a real issue as the typical first
thing we do is read from MII_PHYSID1 and MII_PHYSID2 from get_phy_id()
to register a driver for these PHYs.
Coupled with the workaround in drivers/net/phy/bcm7xxx.c, this
workaround for the MDIO bus controller consists in scanning the list of
PHYs to do this initial read workaround for as part of the MDIO bus
reset routine which is invoked prior to mdiobus_scan().
Once we have a proper PHY driver/device registered, all workarounds are
located there (e.g: power management suspend/resume calls).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, MoCA fixed PHYs are always in link-up state, regardless of
whether the link is actually up or not.
Add code to properly detect MoCA link state changes and to reflect the
new state in MoCA fixed PHY. Only GENET V3 and V4 MACs are capable of
detecting MoCA link state changes.
The code works as follows:
1. GENET MAC detects MoCA link state change and issues UMAC_IRQ_LINK_UP
or UMAC_IRQ_LINK_DOWN interrupt.
2. Link up/down interrupt is processed in bcmgenet_irq_task(), which
calls phy_mac_interrupt().
3. phy_mac_interrupt() updates the fixed PHY phydev->link and kicks
the PHY state machine.
4. PHY state machine proceeds to read the fixed PHY link status
register.
5. When the fixed PHY link status register is being read, the new
function bcmgenet_fixed_phy_link_update() gets called. It copies
the fixed PHY phydev->link value to the fixed PHY status->link.
6. PHY state machine receives the new link state of the fixed PHY.
7. MoCA fixed PHY link state now correctly reflects the real MoCA
hardware link state.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
