| Age | Commit message (Collapse) | Author |
|---|
|
During error recovery or hot firmware upgrade, the chip may be under
reset and the PHC register read cycles may cause completion timeouts.
Check that the chip is not under reset condition before proceeding
to read the PHC by checking the flag BNXT_STATE_IN_FW_RESET. We also
need to take the ptp_lock before we set this flag to prevent race
conditions.
We need this logic because the PHC now will stay registered after
bnxt_close().
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was pointed out by Richard Cochran that registering the PHC during
probe is better than during ifup, so move bnxt_ptp_init() back to
bnxt_init_one(). In order to work correctly after firmware reset which
may result in PTP config. changes, we modify bnxt_ptp_init() to return
if the PHC has been registered earlier. If PTP is no longer supported
by the new firmware, we will unregister the PHC and clean up.
This partially reverts:
d7859afb6880 ("bnxt_en: Move bnxt_ptp_init() to bnxt_open()")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We use the timecounter APIs for the 48-bit PHC and packet timestamps.
We must periodically update the timecounter at roughly half the
overflow interval. The overflow interval is about 78 hours, so
update it every 19 hours (1/4 interval) for some extra margins.
Fixes: 390862f45c85 ("bnxt_en: Get the full 48-bit hardware timestamp periodically")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device needs to be in ifup state for PTP to function, so move
bnxt_ptp_init() to bnxt_open(). This means that the PHC will be
registered during bnxt_open().
This also makes firmware reset work correctly. PTP configurations
may change after firmware upgrade or downgrade. bnxt_open() will
be called after firmware reset, so it will work properly.
bnxt_ptp_start() is now incorporated into bnxt_ptp_init(). We now
also need to call bnxt_ptp_clear() in bnxt_close().
Fixes: 93cb62d98e9c ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setup the TXBD to enable TX timestamp if requested. At TX packet DMA
completion, if we requested TX timestamp on that packet, we defer to
.do_aux_work() to obtain the TX timestamp from the firmware before we
free the TX SKB.
v2: Use .do_aux_work() to get the TX timestamp from firmware.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the RX packet is timestamped by the hardware, the RX completion
record will contain the lower 32-bit of the timestamp. This needs
to be combined with the upper 16-bit of the periodic timestamp that
we get from the timer. The previous snapshot in ptp->old_timer is
used to make sure that the snapshot is not ahead of the RX timestamp
and we adjust for wrap-around if needed.
v2: Make ptp->old_time read access safe on 32-bit CPUs.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From the bnxt_timer(), read the 48-bit hardware running clock
periodically and store it in ptp->current_time. The previous snapshot
of the clock will be stored in ptp->old_time. The old_time snapshot
will be used in the next patches to compute the RX packet timestamps.
v2: Use .do_aux_work() to read the timer periodically.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the clock APIs to set/get/adjust the hw clock, and the related
ioctls and ethtool methods.
v2: Propagate error code from ptp_clock_register().
Add spinlock to serialize access to the timecounter. The
timecounter is accessed in process context and the RX datapath.
Read the PHC using direct registers.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
