| Age | Commit message (Collapse) | Author |
|---|
|
Use the v4l2_find_nearest_size_conditional() helper to figure out which
drive-supported lane can be used on a given system.
Also avoid exposing duplicate frame sizes to userspace when multiple
modes share the same resolution but differ in lane count.
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Use the v4l2_link_freq_to_bitmap() helper to figure out which
driver-supported link frequencies can be used on a given system.
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
[hverkuil: drop unused variable 'max']
|
|
This follows the previous cleanup commit where duplicate entries were
removed from each mode's register list.
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Prepare for refactoring register table by removing register entries
that are common across all modes from resolution-specific table
These will be moved into a shared common register array in the next commit.
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Add register settings for 1500Mbps to support both 2-lane
and 4-lane configurations
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
To prepare upcoming support of multiple sensor modes,
this change separates the lane configuration and PLL settings
from the original mode-specific settings.
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Some users are reporting that ov08x40_identify_module() fails
to identify the chip reading 0x00 as value for OV08X40_REG_CHIP_ID.
Intel's out of tree IPU6 drivers include some ov08x40 changes
including adding support for the reset GPIO for older kernels and
Intel's patch for this uses 5 ms. Extend the sleep to 5 ms following
Intel's example, this fixes the ov08x40_identify_module() problem.
Link: https://github.com/intel/ipu6-drivers/blob/c09e2198d801e1eb701984d2948373123ba92a56/patch/v6.12/0008-media-ov08x40-Add-support-for-2-4-lanes-support-at-1.patch#L4607
Fixes: df1ae2251a50 ("media: ov08x40: Add OF probe support")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Debug log the chip ID after successfully identifying the chip, this is
useful to see if the identification is done on probe() time or if it is
delayed till the first stream on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
We should put/leave the sensor in reset when requesting the GPIO, after
requesting it there are 2 possible scenarios and having the GPIO driven
low is no good in either scenario:
1. The sensor was in ACPI D0 before probe() runs, in this case
ov08x40_power_on() + ov08x40_identify_module() will run immediately
after requesting the GPIO and ov08x40_power_on() starts with driving
the GPIO high. So if the GPIO was already high it will very shortly
be driven low, more of a spike to low then actually properly be driven
low. Which may leave the sensor in a confused state.
If we request the GPIO to be high at request time then power_on() will
driver it high again (no-op) and then sleep for 1-2 ms, so no spike.
2. The sensor was in ACPI D3 / off before probe(), in this case probe()
leaves the sensor alone. But when the sensor is off its reset line
should be driven high not low.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
All ov08x40_check_hwcfg() error-exit paths already log a detailed reason,
logging a second generic "failed to check hwcfg" error is not useful, and
in case of the fwnode check failing with -EPROBE_DEFER this is outright
problematic flooding the log with:
[ 4.557059] ov08x40 i2c-OVTI08F4:00: failed to check hwcfg: -517
[ 4.559636] ov08x40 i2c-OVTI08F4:00: failed to check hwcfg: -517
etc.
messages.
The one exception to all ov08x40_check_hwcfg() error-exit paths already
logging an error is on v4l2_fwnode_endpoint_alloc_parse() errors.
Make ov08x40_check_hwcfg() log an error in that case too and drop
the duplicate "failed to check hwcfg: %d\n" error logging.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
A number of dev_err() error messages miss a terminating '\n', add
the missing '\n' to these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The driver might skip the ov08x40_identify_module() on probe() based on
the acpi_dev_state_d0() check done in probe().
If the ov08x40_identify_module() call is skipped on probe() it should
be done on the first stream start. Add the missing call.
Note ov08x40_identify_module() will only do something on its first call,
subsequent calls are no-ops.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fixes: b1a42fde6e07 ("media: ov08x40: Avoid sensor probing in D0 state")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Improve ov08x40_[read|write]_reg() error returns, if we got an errno value
from the I2C core use that instead of always returning -EIO.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
ov08x40_identify_module() already logs an error if the read ID mismatches,
so having its caller also log an error results in 2 errors in this case.
Add error logging to the ID register read in ov08x40_identify_module() and
drop the error logging in the caller.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Move the ov08x40_identify_module() function to above ov08x40_set_stream()
this is a preparation patch for adding a missing ov08x40_identify_module()
call to ov08x40_set_stream().
No functional changes, just moving code around.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
ACPI platforms might also have a clk provider which needs to be controlled,
always try to get a clk using clk_get_optional() and when that fails fall
back to getting the xvclk frequency from the "clock-frequency" property.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
ACPI platforms might also have a reset GPIO and regulators, move the code
to get these outside of the if (!is_acpi_node(fwnode)) check.
This also removes the is_acpi_node(fwnode) checks from ov08x40_power_on() /
ov08x40_power_off() both the GPIO hand the clk frameworks functions used
there will happily accept the NULL pointer returned from the optional get()
functions when there is no reset GPIO / no clk.
While moving the code around also at error logging to the error exit
path for getting the reset GPIO.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
If the bridge has not yet setup the fwnode-graph then
the fwnode_property_read_u32("clock-frequency") call will fail.
Make the fwnode_graph_get_next_endpoint() call the first call in
ov08x40_check_hwcfg() and return -EPROBE_DEFER if it fails.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Commit df1ae2251a50 ("media: ov08x40: Add OF probe support") added support
for a reset GPIO, regulators and a clk provider controlled through new
ov08x40_power_off() and ov08x40_power_on() functions.
But it missed adding a pm ops structure to call these functions on
runtime suspend/resume. Add the missing pm ops and only call
ov08x40_power_off() on remove() when not already runtime-suspended
to avoid unbalanced regulator / clock disable calls.
Fixes: df1ae2251a50 ("media: ov08x40: Add OF probe support")
Cc: stable@vger.kernel.org
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Linux 6.12-rc7
* tag 'v6.12-rc7': (1909 commits)
Linux 6.12-rc7
filemap: Fix bounds checking in filemap_read()
i2c: designware: do not hold SCL low when I2C_DYNAMIC_TAR_UPDATE is not set
mailmap: add entry for Thorsten Blum
ocfs2: remove entry once instead of null-ptr-dereference in ocfs2_xa_remove()
signal: restore the override_rlimit logic
fs/proc: fix compile warning about variable 'vmcore_mmap_ops'
ucounts: fix counter leak in inc_rlimit_get_ucounts()
selftests: hugetlb_dio: check for initial conditions to skip in the start
mm: fix docs for the kernel parameter ``thp_anon=``
mm/damon/core: avoid overflow in damon_feed_loop_next_input()
mm/damon/core: handle zero schemes apply interval
mm/damon/core: handle zero {aggregation,ops_update} intervals
mm/mlock: set the correct prev on failure
objpool: fix to make percpu slot allocation more robust
mm/page_alloc: keep track of free highatomic
bcachefs: Fix UAF in __promote_alloc() error path
bcachefs: Change OPT_STR max to be 1 less than the size of choices array
bcachefs: btree_cache.freeable list fixes
bcachefs: check the invalid parameter for perf test
...
|
|
The ACPI version of this driver "just works" on dts based systems with a
few extensions to facilitate.
- Add support for DT based probing
- Add support for taking the part out of reset via a GPIO reset pin
- Add in regulator bulk on/off logic for the power rails.
Once done this sensor works nicely on a Qualcomm X1E80100 CRD.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The data-sheet and documentation for this part uses the name xvclk not
ext_clk for the input reference clock. Rename the variables and defines in
this driver to align with the data-sheet name.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
It is necessary to account for I2C quirks in the burst mode path of this
driver. Not all I2C controllers can accept arbitrarily long writes and this
is represented in the quirks field of the adapter structure.
Prior to this patch the following error message is seen on a Qualcomm
X1E80100 CRD.
[ 38.773524] i2c i2c-2: adapter quirk: msg too long (addr 0x0036, size 290, write)
[ 38.781454] ov08x40 2-0036: Failed regs transferred: -95
[ 38.787076] ov08x40 2-0036: ov08x40_start_streaming failed to set regs
Fix the error by breaking up the write sequence into the advertised maximum
write size of the quirks field if the quirks field is populated.
Fixes: 8f667d202384 ("media: ov08x40: Reduce start streaming time")
Cc: stable@vger.kernel.org # v6.9+
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
Because video duration involves calculating the streaming time, and i2c
communication incurs too many XTALK register settings every 4 bytes with
i2c START and STOP.
So we have opted switch to the i2c burst method.
This method involves writing the XTALK registers in the order of
the register block.
The start streaming time can be reduced from around 400ms to 150ms
[Sakari Ailus: Drop unneeded dev_dbg().]
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
This reverts commit feb8831be9d468ee961289c6a275536a1ee0011c.
Commit feb8831be9d468ee961289c6a275536a1ee0011c contained unintentional
changes to Documentation/devicetree/bindings/media/video-interfaces.yaml
and arch/arm/boot/dts/ti/omap/omap3-n9.dts. Revert the entire patch.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Because video duration involves calculating the streaming time, and i2c
communication incurs too many XTALK register settings every 4 bytes with
i2c START and STOP.
So we have opted switch to the i2c burst method.
This method involves writing the XTALK registers in the order of
the register block.
The start streaming time can be reduced from around 400ms to 150ms
[Sakari Ailus: Drop unneeded dev_dbg().]
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
ov08x40 quad bayer sensor ISP has the following work modes:
- normal mode: full size
- 2x2 binned mode: binning size
In normal and binned modes, different tline calculations are
applied.
- normal mode: Tline value needs to be doubled as per the
vendor's update.
Tline time = 2 * HTS / SCLK
Exposure unit : 1 * HTS = 0.5 Tline
- 2x2 binned mode:
Tline time = 1 * HTS / SCLK
Exposure unit : 1 * HTS = 1 Tline
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
When the system enters the D0 state and attempt to probe the device,
another component, such as LED, will also be pulled high due to the
hardware design. It's advisable to keep the device being probed in
a different D state.
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Switch all drivers accessing sub-device state to use the stream-aware
functions. We will soon remove the old ones.
This patch has been generated using the following Coccinelle script:
---------8<------------
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_pad_format(E1, E2, E3)
+ v4l2_subdev_state_get_format(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_pad_crop(E1, E2, E3)
+ v4l2_subdev_state_get_crop(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_pad_compose(E1, E2, E3)
+ v4l2_subdev_state_get_compose(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_try_format(E1, E2, E3)
+ v4l2_subdev_state_get_format(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_try_crop(E1, E2, E3)
+ v4l2_subdev_state_get_crop(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_try_compose(E1, E2, E3)
+ v4l2_subdev_state_get_compose(E2, E3)
---------8<------------
Additionally drivers/media/i2c/s5k5baf.c and
drivers/media/platform/samsung/s3c-camif/camif-capture.c have been
manually changed as Coccinelle didn't. Further local variables have been
removed as they became unused as a result of the other changes.
Also Coccinelle introduced indentation by space in files
drivers/media/i2c/st-mipid02.c and
drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c. This has been also
corrected.
The diff from Coccinelle-generated changes are:
> diff --git b/drivers/media/i2c/imx319.c a/drivers/media/i2c/imx319.c
> index e549692ff478..420984382173 100644
> --- b/drivers/media/i2c/imx319.c
> +++ a/drivers/media/i2c/imx319.c
> @@ -2001,7 +2001,6 @@ static int imx319_do_get_pad_format(struct imx319 *imx319,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &imx319->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/imx355.c a/drivers/media/i2c/imx355.c
> index 96bdde685d65..e1b1d2fc79dd 100644
> --- b/drivers/media/i2c/imx355.c
> +++ a/drivers/media/i2c/imx355.c
> @@ -1299,7 +1299,6 @@ static int imx355_do_get_pad_format(struct imx355 *imx355,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &imx355->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov08x40.c a/drivers/media/i2c/ov08x40.c
> index ca799bbcfdb7..abbb0b774d43 100644
> --- b/drivers/media/i2c/ov08x40.c
> +++ a/drivers/media/i2c/ov08x40.c
> @@ -2774,7 +2774,6 @@ static int ov08x40_do_get_pad_format(struct ov08x40 *ov08x,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov08x->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov13858.c a/drivers/media/i2c/ov13858.c
> index 7816d9787c61..09387e335d80 100644
> --- b/drivers/media/i2c/ov13858.c
> +++ a/drivers/media/i2c/ov13858.c
> @@ -1316,7 +1316,6 @@ static int ov13858_do_get_pad_format(struct ov13858 *ov13858,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov13858->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov13b10.c a/drivers/media/i2c/ov13b10.c
> index 268cd4b03f9c..c06411d5ee2b 100644
> --- b/drivers/media/i2c/ov13b10.c
> +++ a/drivers/media/i2c/ov13b10.c
> @@ -1001,7 +1001,6 @@ static int ov13b10_do_get_pad_format(struct ov13b10 *ov13b,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov13b->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/s5c73m3/s5c73m3-core.c a/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> index 47605e36bc60..8f9b5713daf7 100644
> --- b/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> +++ a/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> @@ -819,7 +819,6 @@ static void s5c73m3_oif_try_format(struct s5c73m3 *state,
> struct v4l2_subdev_format *fmt,
> const struct s5c73m3_frame_size **fs)
> {
> - struct v4l2_subdev *sd = &state->sensor_sd;
> u32 code;
>
> switch (fmt->pad) {
> diff --git a/drivers/media/i2c/s5k5baf.c b/drivers/media/i2c/s5k5baf.c
> index 67da2045f543..03ccfb0e1e11 100644
> --- a/drivers/media/i2c/s5k5baf.c
> +++ b/drivers/media/i2c/s5k5baf.c
> @@ -1472,14 +1472,11 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
>
> if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
> rects = (struct v4l2_rect * []) {
> - &s5k5baf_cis_rect,
> - v4l2_subdev_get_try_crop(sd, sd_state,
> - PAD_CIS),
> - v4l2_subdev_get_try_compose(sd, sd_state,
> - PAD_CIS),
> - v4l2_subdev_get_try_crop(sd, sd_state,
> - PAD_OUT)
> - };
> + &s5k5baf_cis_rect,
> + v4l2_subdev_state_get_crop(sd_state, PAD_CIS),
> + v4l2_subdev_state_get_compose(sd_state, PAD_CIS),
> + v4l2_subdev_state_get_crop(sd_state, PAD_OUT)
> + };
> s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
> return 0;
> }
> diff --git b/drivers/media/platform/samsung/s3c-camif/camif-capture.c a/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> index 295e083f38e8..be58260ea67e 100644
> --- b/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> +++ a/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> @@ -1216,7 +1216,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
> struct v4l2_mbus_framefmt *mf = &fmt->format;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> - mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad);
> + mf = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> fmt->format = *mf;
> return 0;
> }
> @@ -1305,7 +1305,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
> __camif_subdev_try_format(camif, mf, fmt->pad);
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> - mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad);
> + mf = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> *mf = fmt->format;
> mutex_unlock(&camif->lock);
> return 0;
> diff --git b/drivers/media/platform/ti/cal/cal-camerarx.c a/drivers/media/platform/ti/cal/cal-camerarx.c
> index cea454ed9c20..61433744c6c4 100644
> --- b/drivers/media/platform/ti/cal/cal-camerarx.c
> +++ a/drivers/media/platform/ti/cal/cal-camerarx.c
> @@ -621,8 +621,6 @@ static int cal_camerarx_sd_enum_mbus_code(struct v4l2_subdev *sd,
> struct v4l2_subdev_state *state,
> struct v4l2_subdev_mbus_code_enum *code)
> {
> - struct cal_camerarx *phy = to_cal_camerarx(sd);
> -
> /* No transcoding, source and sink codes must match. */
> if (cal_rx_pad_is_source(code->pad)) {
> struct v4l2_mbus_framefmt *fmt;
> diff --git b/drivers/staging/media/imx/imx-ic-prp.c a/drivers/staging/media/imx/imx-ic-prp.c
> index dd558fac6477..61d69f19657e 100644
> --- b/drivers/staging/media/imx/imx-ic-prp.c
> +++ a/drivers/staging/media/imx/imx-ic-prp.c
> @@ -82,8 +82,6 @@ static struct v4l2_mbus_framefmt *
> __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_state *sd_state,
> unsigned int pad, enum v4l2_subdev_format_whence which)
> {
> - struct imx_ic_priv *ic_priv = priv->ic_priv;
> -
> if (which == V4L2_SUBDEV_FORMAT_TRY)
> return v4l2_subdev_state_get_format(sd_state, pad);
> else
> diff --git b/drivers/staging/media/imx/imx-ic-prpencvf.c a/drivers/staging/media/imx/imx-ic-prpencvf.c
> index 02db7dbb884b..ec73c901079e 100644
> --- b/drivers/staging/media/imx/imx-ic-prpencvf.c
> +++ a/drivers/staging/media/imx/imx-ic-prpencvf.c
> @@ -790,8 +790,6 @@ static struct v4l2_mbus_framefmt *
> __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_state *sd_state,
> unsigned int pad, enum v4l2_subdev_format_whence which)
> {
> - struct imx_ic_priv *ic_priv = priv->ic_priv;
> -
> if (which == V4L2_SUBDEV_FORMAT_TRY)
> return v4l2_subdev_state_get_format(sd_state, pad);
> else
> diff --git a/drivers/media/i2c/st-mipid02.c b/drivers/media/i2c/st-mipid02.c
> index 9c9361354c00..b08a249b5fdd 100644
> --- a/drivers/media/i2c/st-mipid02.c
> +++ b/drivers/media/i2c/st-mipid02.c
> @@ -751,7 +751,7 @@ static void mipid02_set_fmt_source(struct v4l2_subdev *sd,
> format->format = bridge->fmt;
> else
> format->format = *v4l2_subdev_state_get_format(sd_state,
> - MIPID02_SINK_0);
> + MIPID02_SINK_0);
>
> /* but code may need to be converted */
> format->format.code = serial_to_parallel_code(format->format.code);
> diff --git a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> index 117912d3bfbd..96353648c032 100644
> --- a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> +++ b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> @@ -319,7 +319,7 @@ static void rkisp1_isp_start(struct rkisp1_isp *isp,
> rkisp1_write(rkisp1, RKISP1_CIF_ISP_CTRL, val);
>
> src_fmt = v4l2_subdev_state_get_format(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
> src_info = rkisp1_mbus_info_get_by_code(src_fmt->code);
>
> if (src_info->pixel_enc != V4L2_PIXEL_ENC_BAYER)
> @@ -475,9 +475,9 @@ static void rkisp1_isp_set_src_fmt(struct rkisp1_isp *isp,
> sink_fmt = v4l2_subdev_state_get_format(sd_state,
> RKISP1_ISP_PAD_SINK_VIDEO);
> src_fmt = v4l2_subdev_state_get_format(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
> src_crop = v4l2_subdev_state_get_crop(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
>
> /*
> * Media bus code. The ISP can operate in pass-through mode (Bayer in,
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The HTS value cannot be directly compared to the sensor's output
size. It needs to be converted to an absolute time unit.
Additionally, the hblank value need to be modified as it was
previous invalid.
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Remove Shawn Tu's and Chiranjeevi Rapolu's e-mail addresses as they are no
longer function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
commit 03c835f498b5 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
In commit ed5c2f5fd10d ("i2c: Make remove callback return void") drivers
were updated to remove the return value of the remove callback, and
return void.
The OV08x40 was added after this commit but was not compile tested at
the time due to a KConfig issue, and this warning was missed.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 38fc5136ac16 ("media: i2c: Add ov08x40 image sensor driver")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Add a V4L2 sub-device driver for Omnivision ov08X40 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- test pattern support
- media controller support
- runtime PM support
- support following resolutions:
+ 3856x2464 at 30FPS
+ 1928x1208 at 30FPS
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
