| Age | Commit message (Collapse) | Author |
|---|
|
Use pm_runtime_put_autosuspend() instead of pm_runtime_put()
to allow autosuspend. Set a 1000ms autosuspend delay in
imx219_probe() to improve power efficiency.
Signed-off-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Switch from s_stream to enable_streams and disable_streams callbacks.
Signed-off-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The LLP_MIN of 3560 is only needed to fix artefacts seen with binned
resolutions. As increasing the LLP reduces the highest possible
framerate by ~3%, use the old default minimum of 3448 if we are not
doing 2x2 analog binning.
Also restore the fll_def value for non-binned modes in the modes
definition to restore the default mode framerate to 30fps.
Suggested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/linux-media/CAPY8ntC1-S6zKtDvmc6EgyxP+j6rTShuG8Dr8PKb9XQr2PeS_w@mail.gmail.com/
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The pixel rate and binning calculations need the format and resolution
of the sensor, so pass the v4l2 subdev state directly instead of always
operating on the active state.
Suggested-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Link: https://lore.kernel.org/linux-media/sejl7xskif6rlpdsg3jhczjwe5gi6rs53ehbyka6omv2zeg7qq@4iis7i2lla5p/
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The imx219_get_binning() function currently returns two separate pieces
of information, the return value is the binning mode enum, and the bin_h
and bin_v references are updated with whether to perform binning in
horizontal and vertical dimensions.
It is simpler to combine both of these pieces of information, and
directly update the bin_h and bin_v references with the register value
that we will write to the sensor, which includes if the binning is
digital or analog mode, thus allowing us to remove the superfluous
binning mode enum.
This is only a style change for the driver, with no functionality
updated.
Suggested-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Link: https://lore.kernel.org/linux-media/ubuuob7mb3o5bxoumrxv4rufutgk3lvdmdery6d3bfc6rytfti@tcchhlechzzp/
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
There are no longer variable declarations here, the context is useless.
Signed-off-by: Cosmin Tanislav <demonsingur@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
When the analog binning mode is used for high framerate operation, the
pixel rate is effectively doubled. Account for this when setting up the
pixel clock rate, and applying the vblank and exposure controls.
The previous logic only used analog binning for RAW8, but normal binning
limits the framerate on RAW10 480p [1]. So with this patch we switch to
using special binning (with 2x pixel rate) wherever possible.
[1]: https://github.com/raspberrypi/linux/issues/5493
Co-developed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Co-developed-by: Vinay Varma <varmavinaym@gmail.com>
Signed-off-by: Vinay Varma <varmavinaym@gmail.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The sensor's internal ADC supports a minimum line length of 3448 pixels,
which may be too small to use with analog binning, where ADC operates on
two lines together. Switch to a higher minimum line length of 3560
pixels to fix the blocky artefacts seen with analog binning [1].
To keep the same default framerate as before for all the modes, lower
the default fll value to compensate for the increase in llp.
[1]: https://github.com/raspberrypi/rpicam-apps/issues/281#issuecomment-1082894118
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The HBLANK control was read-only, and always configured such that the
sensor line length register was 3448. This limited the maximum exposure
time that could be achieved to around 1.26 secs.
Make HBLANK read/write so that the line time can be extended, and
thereby allow longer exposures (and slower frame rates). Retain the
overall line length setting when changing modes rather than resetting it
to a default.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The IMX219 datasheet refers to the vertical length + blanking as
FRM_LENGTH instead of VTS.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The datasheet for this sensor documents the minimum vblanking as being
32 lines. It does fix some problems with occasional black lines at the
bottom of images (tested on Raspberry Pi).
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Commit ceddfd4493b3 ("media: i2c: imx219: Support four-lane operation")
added support for device tree to allow configuration of the sensor to
use 4 lanes with a link frequency of 363MHz, and amended the advertised
pixel rate to 280.8MPix/s.
However it didn't change any of the PLL settings, so actually it would
have been running overclocked in the MIPI block, and with the frame
rate and exposure calculations being wrong as the pixel rate was
unchanged.
The pixel rate and link frequency advertised were taken from the "Clock
Setting Example" section of the datasheet. However those are based on an
external clock of 12MHz, and are unachievable with a clock of 24MHz - it
seems PREPLLCLK_VT_DIV and PREPLLCK_OP_DIV can ONLY be set via the
automatic configuration documented in "9-1-2 EXCK_FREQ setting depend on
INCK frequency", not by writing the registers.
The closest we can get with a 24MHz clock is 281.6MPix/s and 364MHz.
Dropping all support for the 363MHz link frequency would cause problems
for existing users, so allow it, but log a warning that the requested
value is being changed to the supported one.
Fixes: ceddfd4493b3 ("media: i2c: imx219: Support four-lane operation")
Cc: stable@vger.kernel.org
Co-developed-by: Peyton Howe <peyton.howe@bellsouth.net>
Signed-off-by: Peyton Howe <peyton.howe@bellsouth.net>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Set the device's runtime PM status and enable runtime PM before
registering the async sub-device. This is needed to avoid the case where
the device is runtime PM resumed while runtime PM has not been enabled
yet.
Also set the device's runtime PM status to suspended in remove only if it
wasn't so already.
Fixes: 1283b3b8f82b ("media: i2c: Add driver for Sony IMX219 sensor")
Cc: stable@vger.kernel.org # for >= v6.6
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
v4l2_subdev_init_finalize() already sets the HAS_EVENTS flag if a
control handler is set, and subdev_do_ioctl() uses
v4l2_ctrl_subdev_subscribe_event() and v4l2_event_subdev_unsubscribe()
as defaults if the subdev doesn't have .(un)subscribe.
Let's drop the HAS_EVENTS flag and event handlers.
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
It was reported to me that the imx219 didn't work on one of our
development kits partly because the access sequence is incorrect.
The datasheet I could find [1] for this camera has the access sequence:
Seq. No. Address (Hex) data
1 30EB 05
2 30EB 0C
3 300A FF
4 300B FF
5 30EB 05
6 30EB 09
but the driver swaps the first two elements. Laurent pointed out on IRC
that the original code used the correct sequence for 1920x1080 but the
current sequence for 3280x2464 and 1640x1232. During refactoring of the
init sequence the current order was used for all formats.
Switch to using the documented sequence.
Link: https://www.opensourceinstruments.com/Electronics/Data/IMX219PQ.pdf [1]
Fixes: 8508455961d5 ("media: i2c: imx219: Split common registers from mode tables")
Fixes: 1283b3b8f82b ("media: i2c: Add driver for Sony IMX219 sensor")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon-kit
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Drop dev_err() and use the dev_err_probe() helper on probe path.
No functional changes intended.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The subdev .init_cfg() operation is affected by two issues:
- It has long been extended to initialize a whole v4l2_subdev_state
instead of just a v4l2_subdev_pad_config, but its name has stuck
around.
- Despite operating on a whole subdev state and not being directly
exposed to the subdev users (either in-kernel or through the userspace
API), .init_cfg() is categorized as a subdev pad operation.
This participates in making the subdev API confusing for new developers.
Fix it by renaming the operation to .init_state(), and make it a subdev
internal operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michael Riesch <michael.riesch@wolfvision.net> # for imx415
Acked-by: Shuah Khan <skhan@linuxfoundation.org> # for vimc
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
[Sakari Ailus: Resolved a conflict in Renesas vsp1 driver.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Switch all drivers accessing sub-device state to use the stream-aware
functions. We will soon remove the old ones.
This patch has been generated using the following Coccinelle script:
---------8<------------
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_pad_format(E1, E2, E3)
+ v4l2_subdev_state_get_format(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_pad_crop(E1, E2, E3)
+ v4l2_subdev_state_get_crop(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_pad_compose(E1, E2, E3)
+ v4l2_subdev_state_get_compose(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_try_format(E1, E2, E3)
+ v4l2_subdev_state_get_format(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_try_crop(E1, E2, E3)
+ v4l2_subdev_state_get_crop(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_try_compose(E1, E2, E3)
+ v4l2_subdev_state_get_compose(E2, E3)
---------8<------------
Additionally drivers/media/i2c/s5k5baf.c and
drivers/media/platform/samsung/s3c-camif/camif-capture.c have been
manually changed as Coccinelle didn't. Further local variables have been
removed as they became unused as a result of the other changes.
Also Coccinelle introduced indentation by space in files
drivers/media/i2c/st-mipid02.c and
drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c. This has been also
corrected.
The diff from Coccinelle-generated changes are:
> diff --git b/drivers/media/i2c/imx319.c a/drivers/media/i2c/imx319.c
> index e549692ff478..420984382173 100644
> --- b/drivers/media/i2c/imx319.c
> +++ a/drivers/media/i2c/imx319.c
> @@ -2001,7 +2001,6 @@ static int imx319_do_get_pad_format(struct imx319 *imx319,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &imx319->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/imx355.c a/drivers/media/i2c/imx355.c
> index 96bdde685d65..e1b1d2fc79dd 100644
> --- b/drivers/media/i2c/imx355.c
> +++ a/drivers/media/i2c/imx355.c
> @@ -1299,7 +1299,6 @@ static int imx355_do_get_pad_format(struct imx355 *imx355,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &imx355->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov08x40.c a/drivers/media/i2c/ov08x40.c
> index ca799bbcfdb7..abbb0b774d43 100644
> --- b/drivers/media/i2c/ov08x40.c
> +++ a/drivers/media/i2c/ov08x40.c
> @@ -2774,7 +2774,6 @@ static int ov08x40_do_get_pad_format(struct ov08x40 *ov08x,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov08x->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov13858.c a/drivers/media/i2c/ov13858.c
> index 7816d9787c61..09387e335d80 100644
> --- b/drivers/media/i2c/ov13858.c
> +++ a/drivers/media/i2c/ov13858.c
> @@ -1316,7 +1316,6 @@ static int ov13858_do_get_pad_format(struct ov13858 *ov13858,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov13858->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov13b10.c a/drivers/media/i2c/ov13b10.c
> index 268cd4b03f9c..c06411d5ee2b 100644
> --- b/drivers/media/i2c/ov13b10.c
> +++ a/drivers/media/i2c/ov13b10.c
> @@ -1001,7 +1001,6 @@ static int ov13b10_do_get_pad_format(struct ov13b10 *ov13b,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov13b->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/s5c73m3/s5c73m3-core.c a/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> index 47605e36bc60..8f9b5713daf7 100644
> --- b/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> +++ a/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> @@ -819,7 +819,6 @@ static void s5c73m3_oif_try_format(struct s5c73m3 *state,
> struct v4l2_subdev_format *fmt,
> const struct s5c73m3_frame_size **fs)
> {
> - struct v4l2_subdev *sd = &state->sensor_sd;
> u32 code;
>
> switch (fmt->pad) {
> diff --git a/drivers/media/i2c/s5k5baf.c b/drivers/media/i2c/s5k5baf.c
> index 67da2045f543..03ccfb0e1e11 100644
> --- a/drivers/media/i2c/s5k5baf.c
> +++ b/drivers/media/i2c/s5k5baf.c
> @@ -1472,14 +1472,11 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
>
> if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
> rects = (struct v4l2_rect * []) {
> - &s5k5baf_cis_rect,
> - v4l2_subdev_get_try_crop(sd, sd_state,
> - PAD_CIS),
> - v4l2_subdev_get_try_compose(sd, sd_state,
> - PAD_CIS),
> - v4l2_subdev_get_try_crop(sd, sd_state,
> - PAD_OUT)
> - };
> + &s5k5baf_cis_rect,
> + v4l2_subdev_state_get_crop(sd_state, PAD_CIS),
> + v4l2_subdev_state_get_compose(sd_state, PAD_CIS),
> + v4l2_subdev_state_get_crop(sd_state, PAD_OUT)
> + };
> s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
> return 0;
> }
> diff --git b/drivers/media/platform/samsung/s3c-camif/camif-capture.c a/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> index 295e083f38e8..be58260ea67e 100644
> --- b/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> +++ a/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> @@ -1216,7 +1216,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
> struct v4l2_mbus_framefmt *mf = &fmt->format;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> - mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad);
> + mf = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> fmt->format = *mf;
> return 0;
> }
> @@ -1305,7 +1305,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
> __camif_subdev_try_format(camif, mf, fmt->pad);
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> - mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad);
> + mf = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> *mf = fmt->format;
> mutex_unlock(&camif->lock);
> return 0;
> diff --git b/drivers/media/platform/ti/cal/cal-camerarx.c a/drivers/media/platform/ti/cal/cal-camerarx.c
> index cea454ed9c20..61433744c6c4 100644
> --- b/drivers/media/platform/ti/cal/cal-camerarx.c
> +++ a/drivers/media/platform/ti/cal/cal-camerarx.c
> @@ -621,8 +621,6 @@ static int cal_camerarx_sd_enum_mbus_code(struct v4l2_subdev *sd,
> struct v4l2_subdev_state *state,
> struct v4l2_subdev_mbus_code_enum *code)
> {
> - struct cal_camerarx *phy = to_cal_camerarx(sd);
> -
> /* No transcoding, source and sink codes must match. */
> if (cal_rx_pad_is_source(code->pad)) {
> struct v4l2_mbus_framefmt *fmt;
> diff --git b/drivers/staging/media/imx/imx-ic-prp.c a/drivers/staging/media/imx/imx-ic-prp.c
> index dd558fac6477..61d69f19657e 100644
> --- b/drivers/staging/media/imx/imx-ic-prp.c
> +++ a/drivers/staging/media/imx/imx-ic-prp.c
> @@ -82,8 +82,6 @@ static struct v4l2_mbus_framefmt *
> __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_state *sd_state,
> unsigned int pad, enum v4l2_subdev_format_whence which)
> {
> - struct imx_ic_priv *ic_priv = priv->ic_priv;
> -
> if (which == V4L2_SUBDEV_FORMAT_TRY)
> return v4l2_subdev_state_get_format(sd_state, pad);
> else
> diff --git b/drivers/staging/media/imx/imx-ic-prpencvf.c a/drivers/staging/media/imx/imx-ic-prpencvf.c
> index 02db7dbb884b..ec73c901079e 100644
> --- b/drivers/staging/media/imx/imx-ic-prpencvf.c
> +++ a/drivers/staging/media/imx/imx-ic-prpencvf.c
> @@ -790,8 +790,6 @@ static struct v4l2_mbus_framefmt *
> __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_state *sd_state,
> unsigned int pad, enum v4l2_subdev_format_whence which)
> {
> - struct imx_ic_priv *ic_priv = priv->ic_priv;
> -
> if (which == V4L2_SUBDEV_FORMAT_TRY)
> return v4l2_subdev_state_get_format(sd_state, pad);
> else
> diff --git a/drivers/media/i2c/st-mipid02.c b/drivers/media/i2c/st-mipid02.c
> index 9c9361354c00..b08a249b5fdd 100644
> --- a/drivers/media/i2c/st-mipid02.c
> +++ b/drivers/media/i2c/st-mipid02.c
> @@ -751,7 +751,7 @@ static void mipid02_set_fmt_source(struct v4l2_subdev *sd,
> format->format = bridge->fmt;
> else
> format->format = *v4l2_subdev_state_get_format(sd_state,
> - MIPID02_SINK_0);
> + MIPID02_SINK_0);
>
> /* but code may need to be converted */
> format->format.code = serial_to_parallel_code(format->format.code);
> diff --git a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> index 117912d3bfbd..96353648c032 100644
> --- a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> +++ b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> @@ -319,7 +319,7 @@ static void rkisp1_isp_start(struct rkisp1_isp *isp,
> rkisp1_write(rkisp1, RKISP1_CIF_ISP_CTRL, val);
>
> src_fmt = v4l2_subdev_state_get_format(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
> src_info = rkisp1_mbus_info_get_by_code(src_fmt->code);
>
> if (src_info->pixel_enc != V4L2_PIXEL_ENC_BAYER)
> @@ -475,9 +475,9 @@ static void rkisp1_isp_set_src_fmt(struct rkisp1_isp *isp,
> sink_fmt = v4l2_subdev_state_get_format(sd_state,
> RKISP1_ISP_PAD_SINK_VIDEO);
> src_fmt = v4l2_subdev_state_get_format(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
> src_crop = v4l2_subdev_state_get_crop(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
>
> /*
> * Media bus code. The ISP can operate in pass-through mode (Bayer in,
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The exposure_max, exposure_def and hblank variables are only used in an
inner scope in the imx219_set_pad_format() function. Move them to that
scope to keep them closer to their usage and improve readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Subdev state variables are named with a mix of 'state' and 'sd_state'
through the driver. To improve consistency, name them all 'state'.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Calculate the crop rectangle size and location dynamically when setting
the format, instead of storing it in the imx219_mode structure. This
removes duplicated information from the mode, to guarantee consistency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The IMX219 has distinct binning registers for the horizontal and
vertical directions. Calculate their value and write them separately.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Instead of duplicating the logical implemented in the .set_fmt()
operation in .init_cfg(), call .set_fmt() directly. This centralizes the
format and crop rectangle calculations in a single place.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Simplify the imx219_set_stream() by removing an unneeded goto statement,
and its corresponding error label. The natural flow of the function is
correct.
While at it, drop a useless comment.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Move functions around to group them by purpose, in order to improve
readability. No functional change is intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The IMX219_VTS_* macros define default VTS values for the modes
supported by the driver. They are used in a single place, and hinder
readability compared to using the value directly as a decimal number.
Drop them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The mode field of the imx219 structure is only used in
imx219_init_controls(), after the probe function sets it to point to the
default mode. Use the default mode directly when initializing controls,
and drop the mode field from the imx219 structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Use the active format height instead of the mode height in
imx219_set_ctrl(). This prepares for dropping the mode field from the
imx219 structure.
The state is retrieved using v4l2_subdev_get_locked_active_state() as
the subdev active state and the control handler share the same lock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Compare the format and crop rectangle dimensions to infer binning
settings, instead of storing the binning mode in the imx219_mode
structure. This removes duplicate information from the mode.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Configure the crop-related registers from the values stored in the
active crop rectangle instead of the mode structure. This removes usage
of the mode from the imx219_set_framefmt(). No functional change is
intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
While the ycbcr_enc field doesn't apply to raw formats, leaving it
uninitialized makes the driver behave in a less deterministic way. Fix
it by picking the default value for the colorspace.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The imx219_set_binning() function sets registers based on the bpp value,
which is computed in imx219_set_framefmt(). As both functions are called
from the same place consecutively, and set registers based on the
selected mode, merge them together to simplify the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Replace the per-mode register arrays with code that sets the same
register values using the mode definitions. This avoids duplicating
information in two different places.
The error check for invalid formats in imx219_set_framefmt() is dropped
as the format is guaranteed to be valid.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The 640x480 mode specifies incorrect values for the TP_WINDOW_WIDTH and
TP_WINDOW_HEIGHT registers, which likely got copied from the 1640x1232
mode. They should be identical to the X_OUTPUT_SIZE and Y_OUTPUT_SIZE
registers as for all the other modes, to avoid cropping the test
pattern. Fix them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The IMX219_REG_CSI_LANE_MODE is configured twice, once with a hardcoded
value in the imx219_common_regs registers array, and once with the value
appropriate for the system in imx219_configure_lanes(). The latter is
enough, drop the former.
Fixes: ceddfd4493b3 ("media: i2c: imx219: Support four-lane operation")
Suggested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Define macros for all the known registers used in the register arrays,
and use them to replace the numerical addresses. This improves
readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Drop a handful of macros that are not used and don't provide any value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Use the new common CCI register access helpers to replace the private
register access helpers in the imx219 driver. This simplifies the driver
by reducing the amount of code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The .set_fmt() handler tries to avoid updating the sensor configuration
when the mode hasn't changed. It does so by comparing both the mode and
the media bus code. While the latter correctly uses the media bus code
stored in the subdev state, the former compares the mode being set with
the active mode, regardless of whether .set_fmt() is called for the
ACTIVE or TRY format. This can lead to .set_fmt() returning early when
operating on TRY formats.
This could be fixed by replacing the mode comparison with width and
height comparisons, using the frame size stored in the subdev state.
However, the optimization that avoids updates to the sensor
configuration is not very useful, and is not commonly found in sensor
drivers. To improve consistency across sensor drivers, it is better, in
addition to being easier, to simply drop it. Do so.
Fixes: e8a5b1df000e ("media: i2c: imx219: Use subdev active state")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
When moving the imx219 driver to the subdev active state, commit
e8a5b1df000e ("media: i2c: imx219: Use subdev active state") used the
pad crop rectangle stored in the subdev state to report the crop
rectangle of the active mode. That crop rectangle was however not set in
the state when setting the format, which resulted in reporting an
incorrect crop rectangle to userspace. Fix it.
Fixes: e8a5b1df000e ("media: i2c: imx219: Use subdev active state")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The imx219_init_cfg() function has stopped operating on the try format
since commit 7e700847b1fe ("media: i2c: imx219: Switch from open to
init_cfg"), but a comment in the function wasn't updated. Fix it.
While at it, improve spelling in a second comment in the function.
Fixes: 7e700847b1fe ("media: i2c: imx219: Switch from open to init_cfg")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The imx219_set_pad_format() function adjusts the media bus code provided
through the v4l2_subdev_format parameter to a media bus code known
to be supported by the sensor.
The same exact operation is performed by the imx219_get_format_code()
function which called by imx219_update_pad_format(), which is in the
imx219_set_pad_format() call path.
Remove the duplicated operation and simplify imx219_set_pad_format().
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The set_fmt and init_cfg functions both fills a v4l2_mbus_framefmt
instance, passing in the mode and the media bus code. While set_fmt
uses function helpers, init_cfg open-codes the assignments.
Simplify the format initialization by moving it to a common helper.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Port the imx219 sensor driver to use the subdev active state.
Move all the format configuration to the subdevice state and simplify
the format handling, locking and initialization.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The IMX219 is a RAW sensor. Fix the colorspace configuration by
using V4L2_COLORSPACE_RAW and adjust the quantization and transfer
function values. Drop ycbcr_enc as it doesn't apply to RAW sensors.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Complete the default format initialization in init_cfg() filling in
the fields for the colorspace configuration copied from
imx219_set_default_format().
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Use the init_cfg pad level operation instead of the internal subdev
open operation to set default formats on the pads.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The imx219 is using the name "codes" for the mbus formats array. The
name is too generic and not easy to read and follow in the code. Change
it to imx219_mbus_formats.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
