| Age | Commit message (Collapse) | Author |
|---|
|
If rx-no-low-drive is set, then the CEC pin framework will disable
the detection of situations where a Low Drive has to be generated.
So if this is set, then we will never generate Low Drives.
This helps testing whether other CEC devices generate Low Drive
pulses by ensuring it is not us that is generating them.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This adds support for inserting 'glitches' after a falling and/or
rising edge. This tests what happens when there are little voltage
spikes after falling or rising edges, which can be caused due to
noise or reflections on the CEC line.
A proper CEC implementation will deglitch this, but a poor implementation
can create a Low Drive pulse in response, effectively making CEC unusable.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- platform: synopsys: hdmirx: Fix 64-bit division for 32-bit targets
- vim2m: print device name after registering device
- Synopsys DesignWare HDMI RX Driver and various fixes
- cec/printk fixes and the removal of the vidioc_g/s_ctrl and
vidioc_queryctrl callbacks
- AVerMedia H789-C PCIe support and rc-core structs padding
- Several camera sensor patches
- uvcvideo improvements
- visl: Fix ERANGE error when setting enum controls
- codec fixes
- V4L2 camera sensor patches mostly
- chips-media: wave5: Fixes
- Add SDM670 camera subsystem
- Qualcomm iris video decoder driver
- dt-bindings: update clocks for sc7280-camss
- various fixes and enhancements
* tag 'media/v6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (264 commits)
media: pci: mgb4: include linux/errno.h
media: synopsys: hdmirx: Fix signedness bug in hdmirx_parse_dt()
media: platform: synopsys: hdmirx: Fix 64-bit division for 32-bit targets
media: vim2m: print device name after registering device
media: vivid: Introduce VIDEO_VIVID_OSD
media: vivid: Move all fb_info references into vivid-osd
media: platform: synopsys: hdmirx: Optimize struct snps_hdmirx_dev
media: platform: synopsys: hdmirx: Remove unused HDMI audio CODEC relics
media: platform: synopsys: hdmirx: Remove duplicated header inclusion
media: qcom: Clean up Kconfig dependencies
media: dvb-frontends: tda10048: Make the range of z explicit.
media: platform: stm32: Add check for clk_enable()
media: xilinx-tpg: fix double put in xtpg_parse_of()
media: siano: Fix error handling in smsdvb_module_init()
media: c8sectpfe: Call of_node_put(i2c_bus) only once in c8sectpfe_probe()
media: i2c: tda1997x: Call of_node_put(ep) only once in tda1997x_parse_dt()
dt-bindings: media: mediatek,vcodec: Revise description
dt-bindings: media: mediatek,jpeg: Relax IOMMU max item count
media: v4l2-dv-timings: prevent possible overflow in v4l2_detect_gtf()
media: rockchip: rga: fix rga offset lookup
...
|
|
[Why]
There are several ns_to_ktime() calls that require using nanoseconds. It is
better to replace them with us_to_ktime() to make code clear, getting rid
of multiplication by 1000.
Also the timer function code may have an integer wrap-around issue. Since
both tx_custom_low_usecs and tx_custom_high_usecs can be set to up to
9999999 from the user space via cec_pin_error_inj_parse_line(), this may
cause usecs to be overflowed when adap->monitor_pin_cnt is zero and usecs
is multiplied by 1000.
[How]
Take advantage of using an appropriate helper func us_to_ktime() instead of
ns_to_ktime() to improve readability and to make the code clearer. And this
also mitigates possible integer wrap-arounds when usecs value is too large
and it is multiplied by 1000.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Signed-off-by: Vitaliy Shevtsov <v.shevtsov@mt-integration.ru>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/c725ad8d0ecac3cf6bbc532af567e56d47a6b75c.1738746904.git.namcao@linutronix.de
|
|
Having cec.h include linux/debugfs.h leads to all users of all cec
headers include and depend on debugfs.h and its dependencies for no
reason. Drop the include from cec.h, and include debugfs.h and
seq_file.h where needed.
Sort all the modified include lists while at it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The CEC interrupt is only needed if userspace wants to monitor
the CEC pin for an unconfigured CEC device. That gives it the
most precise CEC pin debugging results.
This avoids a corner case where the interrupt is enabled for
a short period when the adapter is about to be configured.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The CEC pin framework needs a bit more control over the interrupt
handling: make sure that the disable_irq op is called even if the
device node is unregistered, log the state of the interrupt in
debugfs, and disable the interrupt when the kernel thread is stopped.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
It's OK to keep the pending pin events when disabling or
enabling the 'adapter'. Zeroing this can cause a race condition
if this happens when the pin kthread is handling a pin event
and calls atomic_dec later, causing work_pin_num_events to become
negative.
Just leave pending events in the queue, they'll be read eventually.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
When the adap_enable callback is called the adap->lock is held.
When disabling the adapter it attempts to stop the kthread that
deals with receiving and transmitting messages. However, kthread_stop
waits for the thread to stop, so all that time adap->lock is held.
Unfortunately, the kernel thread itself can call functions that take
that same lock, so a deadlock can occur.
Change the logic to keep the kernel thread running and instead when
disabling the adapter, just set the pin to high, go to idle and then
to state OFF and disable the interrupt. Only stop the kernel thread
when the adapter is deleted.
This way disabling the adapter will not wait for anything and the
deadlock is avoided.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Use call_(void_)op consistently in the CEC core framework. Ditto
for the cec pin ops. And check if !adap->devnode.unregistered before
calling each op. This avoids calls to ops when the device has been
unregistered and the underlying hardware may be gone.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The en/disable_irq() functions keep track of the 'depth': i.e. if
interrupts are disabled twice, then it needs to enable_irq() calls to
enable them again. The cec-pin framework didn't take this into accound
and could disable irqs multiple times, and it expected that a single
enable_irq() would enable them again.
Move all calls to en/disable_irq() to the kthread where it is easy
to keep track of the current irq state and ensure that multiple
en/disable_irq calls never happen.
If interrupts where disabled twice, then they would never turn on
again, leaving the CEC adapter in a dead state.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 865463fc03ed (media: cec-pin: add error injection support)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This field is only set, but never used. Drop it.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The CEC pin framework has to wait for the CEC bus to be idle for the
requested Signal Free Time before it can start a transmit.
However, the check for that was off by one, so transmits would start one
bit period (2.4ms) too late.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The cec pin timer overruns are measured in microseconds, but the variable
names include the millisecond symbol "ms". To avoid confusion, replace
"ms" with "us" in the variable names and printed status message.
Signed-off-by: Deborah Brouwer <deborahbrouwer3563@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
In preparation for moving CEC drivers to the CEC directory,
move the core to a separate place.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
