| Age | Commit message (Collapse) | Author |
|---|
|
When determining the actual best period by looping through all
possible PWM configs, the resolution currently used is based on
bit shift value which is off-by-one above the possible maximum
PWM value allowed.
So subtract one from the resolution before determining the best
period so that the maximum duty cycle requested by the PWM user
won't result in a value above the maximum allowed by the selected
resolution.
Cc: stable@vger.kernel.org # 6.4
Fixes: b00d2ed37617 ("leds: rgb: leds-qcom-lpg: Add support for high resolution PWM")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20250305-leds-qcom-lpg-fix-max-pwm-on-hi-res-v4-3-bfe124a53a9f@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Ideally, the requested duty cycle should never translate to a PWM
value higher than the selected resolution (PWM size), but currently the
best matched period is never reported back to the PWM consumer, so the
consumer will still be using the requested period which is higher than
the best matched one. This will result in PWM consumer requesting
duty cycle values higher than the allowed PWM value.
For example, a consumer might request a period of 5ms while the best
(closest) period the PWM hardware will do is 4.26ms. For this best
matched resolution, if the selected resolution is 8-bit wide, when
the consumer asks for a duty cycle of 5ms, the PWM value will be 300,
which is outside of what the resolution allows. This will happen with
all possible resolutions when selected.
Since for these Hi-Res PWMs, the current implementation is capping the PWM
value at a 15-bit resolution, even when lower resolutions are selected,
the value will be wrapped around by the HW internal logic to the selected
resolution.
Fix the issue by capping the PWM value to the maximum value allowed by
the selected resolution.
Cc: stable@vger.kernel.org # 6.4
Fixes: b00d2ed37617 ("leds: rgb: leds-qcom-lpg: Add support for high resolution PWM")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20250305-leds-qcom-lpg-fix-max-pwm-on-hi-res-v4-2-bfe124a53a9f@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Ideally, the requested duty cycle should never translate to a PWM
value higher than the selected resolution (PWM size), but currently the
best matched period is never reported back to the PWM consumer, so the
consumer will still be using the requested period which is higher than
the best matched one. This will result in PWM consumer requesting
duty cycle values higher than the allowed PWM value.
For example, a consumer might request a period of 5ms while the best
(closest) period the PWM hardware will do is 4.26ms. For this best
matched resolution, if the selected resolution is 9-bit wide, when
the consumer asks for a duty cycle of 5ms, the PWM value will be 600,
which is outside of what the resolution allows. Similar will happen
if the 6-bit resolution is selected.
Since for these normal PWMs (non Hi-Res), the current implementation is
capping the PWM value at a 9-bit resolution, even when the 6-bit
resolution is selected, the value will be wrapped around to 6-bit value
by the HW internal logic.
Fix the issue by capping the PWM value to the maximum value allowed by
the selected resolution.
Fixes: 7a3350495d9a ("leds: rgb: leds-qcom-lpg: Add support for 6-bit PWM resolution")
Suggested-by: Anjelique Melendez <anjelique.melendez@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20250305-leds-qcom-lpg-fix-max-pwm-on-hi-res-v4-1-bfe124a53a9f@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Currently, driver only allows for PWM modules to use 9-bit resolution.
However, PWM modules can support 6-bit and 9-bit resolution. Add support
for 6-bit resolution.
Suggested-by: Zejiong Huang <zejiongh@qti.qualcomm.com>
Signed-off-by: Anjelique Melendez <anjelique.melendez@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250213003533.1684131-1-anjelique.melendez@oss.qualcomm.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240816-cleanup-h-of-node-put-var-v1-17-1d0292802470@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Currently, all LED LPG devices will call lpg_{set,clear}_pbs_trigger()
when setting brightness regardless of if they support PPG and have PBS
triggers. Check if device supports PPG before setting/clearing PBS
triggers.
Fixes: 6ab1f766a80a ("leds: rgb: leds-qcom-lpg: Add support for PPG through single SDAM")
Fixes: 5e9ff626861a ("leds: rgb: leds-qcom-lpg: Include support for PPG with dedicated LUT SDAM")
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20240607005250.4047135-1-quic_amelende@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The PMI8950 PMIC contains 1 PWM channel
Signed-off-by: Gianluca Boiano <morf3089@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240402-pmi8950-pwm-support-v1-1-1a66899eeeb3@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Core Framework:
- Introduce ExpressWire library
New Drivers:
- Add support for ON Semiconductor NCP5623 RGB LED Driver
New Device Support:
- Add support for PM660L to Qualcomm's LPG driver
New Functionality:
- Dynamically load modules required for the default-trigger
- Add some support for suspend and resume
- Allow LEDs to remain lit during suspend
Fix-ups:
- Device Tree binding adaptions/conversions/creation
- Fix include lists; alphabetise, remove unused, explicitly add used
- Add new led_match_default_trigger to avoid duplication
- Add module alias' to aid auto-loading
- Default to hw_control if no others are specified
- De-bloat the supported link speed attribute lists
- Remove superfluous code and simplify overall
- Constify some variables
Bug Fixes:
- Prevent kernel panic when renaming the net interface
- Fix Kconfig related build errors
- Ensure mutexes are unlocked prior to destroying them
- Provide clean-up between state changes to avoid invalid state
- Fix some broken kernel-doc headers"
* tag 'leds-next-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (41 commits)
leds: ncp5623: Add MS suffix to time defines
leds: Add NCP5623 multi-led driver
dt-bindings: leds: Add NCP5623 multi-LED Controller
leds: mlxreg: Drop an excess struct mlxreg_led_data member
leds: leds-mlxcpld: Fix struct mlxcpld_led_priv member name
leds: lm3601x: Fix struct lm3601_led kernel-doc warnings
leds: Fix ifdef check for gpio_led_register_device()
dt-bindings: leds: qcom-lpg: Narrow nvmem for other variants
dt-bindings: leds: qcom-lpg: Drop redundant qcom,pm8550-pwm in if:then:
dt-bindings: leds: Add LED_FUNCTION_WAN_ONLINE for Internet access
leds: sgm3140: Add missing timer cleanup and flash gpio control
leds: expresswire: Don't depend on NEW_LEDS
Revert "leds: Only descend into leds directory when CONFIG_NEW_LEDS is set"
leds: aw2013: Unlock mutex before destroying it
leds: qcom-lpg: Add QCOM_PBS dependency
leds: rgb: leds-group-multicolor: Allow LEDs to stay on in suspend
leds: trigger: netdev: Fix kernel panic on interface rename trig notify
leds: qcom-lpg: Add PM660L configuration and compatible
leds: spi-byte: Use devm_led_classdev_register_ext()
leds: pca963x: Add support for suspend and resume
...
|
|
Inherit PM660L PMIC LPG/triled block configuration from downstream
drivers and DT sources, consisting of a triled block with automatic
trickle charge control and source selection, three colored led channels
belonging to the synchronized triled block and one loose PWM channel.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20240204-pm660l-lpg-v5-1-2f54d1a0894b@somainline.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Update the pm8350c lpg_data struct so that pm8350c devices are treated as
PWM devices that support two-nvmem PPG scheme.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Link: https://lore.kernel.org/r/20231221185838.28440-8-quic_amelende@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
On PMICs such as PM8350C, the pattern lookup table (LUT) is stored in a
separate SDAM from the one where the lpg per-channel data is stored.
Add support for PPG with a dedicated LUT SDAM while maintaining backward
compatibility for those targets that use only a single SDAM.
Co-developed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Signed-off-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Link: https://lore.kernel.org/r/20231221185838.28440-7-quic_amelende@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Update the pmi632 lpg_data struct so that pmi632 devices use PPG
for LUT pattern.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20231221185838.28440-6-quic_amelende@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
In some PMICs like pmi632, the pattern look up table (LUT) and LPG
configuration is stored in a single SDAM module instead of LUT
peripheral. This feature is called PPG. PPG uses Qualcomm Programmable
Boot Sequencer (PBS) inorder to trigger pattern sequences for PMICs.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20231221185838.28440-5-quic_amelende@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
This prepares the pwm sub-driver to further changes of the pwm core
outlined in the commit introducing devm_pwmchip_alloc(). There is no
intended semantical change and the driver should behave as before.
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/0be073477092eeccaac6c021cf07e38fc30c74fc.1707900770.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/4785982785812615d15c7dd6d2755270bd8670b2.1701860672.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
One error path already used dev_err_probe(). Adapt the other error paths
that emit an error message to also use this function for consistency and
slightly simplified code.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231126095230.683204-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
With pwmchip_remove() being automatically called after switching to
devm_pwmchip_add() the remove function can be dropped completely. Yay!
With lpg_remove() gone there is no user of the platform device's drvdata
left, so platform_set_drvdata() can be dropped from .probe(), too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231126095230.683204-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains a few fixes and a bunch of cleanups, a lot of which is
in preparation for Uwe's character device support that may be ready in
time for the next merge window"
* tag 'pwm/for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (37 commits)
pwm: samsung: Document new member .channel in struct samsung_pwm_chip
pwm: bcm2835: Add support for suspend/resume
pwm: brcmstb: Checked clk_prepare_enable() return value
pwm: brcmstb: Utilize appropriate clock APIs in suspend/resume
pwm: pxa: Explicitly include correct DT includes
pwm: cros-ec: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: samsung: Consistently use the same name for driver data
pwm: vt8500: Simplify using devm functions
pwm: sprd: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: sprd: Provide a helper to cast a chip to driver data
pwm: spear: Simplify using devm functions
pwm: mtk-disp: Simplify using devm_pwmchip_add()
pwm: imx-tpm: Simplify using devm functions
pwm: brcmstb: Simplify using devm functions
pwm: bcm2835: Simplify using devm functions
pwm: bcm-iproc: Simplify using devm functions
pwm: Adapt sysfs API documentation to reality
pwm: dwc: add PWM bit unset in get_state call
pwm: dwc: make timer clock configurable
pwm: dwc: split pci out of core driver
...
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
All platform drivers below drivers/leds/ unconditionally return zero in
their remove callback and so can be converted trivially to the variant
returning void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230917130947.1122198-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct lpg_led.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915201059.never.086-kees@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Instead of requiring each driver to care for assigning the owner member
of struct pwm_ops, handle that implicitly using a macro. Note that the
owner member has to be moved to struct pwm_chip, as the ops structure
usually lives in read-only memory and so cannot be modified.
The upside is that new low level drivers cannot forget the assignment and
save one line each. The pwm-crc driver didn't assign .owner, that's not
a problem in practice though as the driver cannot be compiled as a
module.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # Intel LPSS
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> # pwm-{bcm,brcm}*.c
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> # sun4i
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> # pwm-visconti
Acked-by: Heiko Stuebner <heiko@sntech.de> # pwm-rockchip
Acked-by: Michael Walle <michael@walle.cc> # pwm-sl28cpld
Acked-by: Neil Armstrong <neil.armstrong@linaro.org> # pwm-meson
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230804142707.412137-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Since commit f9a8ee8c8bcd ("pwm: Always allocate PWM chip base ID
dynamically") there is no effect any more for assigning this variable. See
pwmchip_add() which unconditionally overwrites this member.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230728065739.580281-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714174651.4058753-1-robh@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for Intel Cherry Trail Whiskey Cove PMIC LEDs
- Add support for Awinic AW20036/AW20054/AW20072 LEDs
New Device Support:
- Add support for PMI632 LPG to QCom LPG
- Add support for PMI8998 to QCom Flash
- Add support for MT6331, WLEDs and MT6332 to Mediatek MT6323 PMIC
New Functionality:
- Implement the LP55xx Charge Pump
- Add support for suspend / resume to Intel Cherry Trail Whiskey Cove PMIC
- Add support for breathing mode to Intel Cherry Trail Whiskey Cove PMIC
- Enable per-pin resolution Pinctrl in LEDs GPIO
Fix-ups:
- Allow thread to sleep by switching from spinlock to mutex
- Add lots of Device Tree bindings / support
- Adapt relationships / dependencies driven by Kconfig
- Switch I2C drivers from .probe_new() to .probe()
- Remove superfluous / duplicate code
- Replace strlcpy() with strscpy() for efficiency and overflow prevention
- Staticify various functions
- Trivial: Fixing coding style
- Simplify / reduce code
Bug Fixes:
- Prevent NETDEV_LED_MODE_LINKUP from being cleared on rename
- Repair race between led_set_brightness(LED_{OFF,FULL})
- Fix Oops relating to sleeping in critical sections
- Clear LED_INIT_DEFAULT_TRIGGER flag when clearing the current trigger
- Do not leak resources in error handling paths
- Fix unsigned comparison which can never be negative
- Provide missing NULL terminating entries in tables
- Fix misnaming issues"
* tag 'leds-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (53 commits)
leds: leds-mt6323: Adjust return/parameter types in wled get/set callbacks
leds: sgm3140: Add richtek,rt5033-led compatible
dt-bindings: leds: sgm3140: Document richtek,rt5033 compatible
dt-bindings: backlight: kinetic,ktz8866: Add missing type for "current-num-sinks"
dt-bindings: leds: Drop unneeded quotes
leds: Fix config reference for AW200xx driver
leds: leds-mt6323: Add support for WLEDs and MT6332
leds: leds-mt6323: Add support for MT6331 leds
leds: leds-mt6323: Open code and drop MT6323_CAL_HW_DUTY macro
leds: leds-mt6323: Drop MT6323_ prefix from macros and defines
leds: leds-mt6323: Specify registers and specs in platform data
dt-bindings: leds: leds-mt6323: Document mt6332 compatible
dt-bindings: leds: leds-mt6323: Document mt6331 compatible
leds: simatic-ipc-leds-gpio: Introduce more Kconfig switches
leds: simatic-ipc-leds-gpio: Split up into multiple drivers
leds: simatic-ipc-leds-gpio: Move two extra gpio pins into another table
leds: simatic-ipc-leds-gpio: Add terminating entries to gpio tables
leds: flash: leds-qcom-flash: Fix an unsigned comparison which can never be negative
leds: cht-wcove: Remove unneeded semicolon
leds: cht-wcove: Fix an unsigned comparison which can never be negative
...
|
|
The introduction of high resolution PWM support changed the order of the
operations in the calculation of min and max period. The result in both
divisions is in most cases a truncation to 0, which limits the period to
the range of [0, 0].
Both numerators (and denominators) are within 64 bits, so the whole
expression can be put directly into the div64_u64, instead of doing it
partially.
Fixes: b00d2ed37617 ("leds: rgb: leds-qcom-lpg: Add support for high resolution PWM")
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Lee Jones <lee@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20230515162604.649203-1-quic_bjorande@quicinc.com
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Ensure child node references are decremented properly in the error path.
Signed-off-by: Lu Hongfei <luhongfei@vivo.com>
Link: https://lore.kernel.org/r/20230525111705.3055-1-luhongfei@vivo.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The PMI632 PMIC contains 5 PWM channels, 3 of which can be used for
LEDs.
For the LED pattern it doesn't have LUT like other PMICs but uses SDAM
instead. This is not currently implemented in the driver but since LPG
works fine without it, add support for the PMIC now.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230414-pmi632-v2-4-98bafa909c36@z3ntu.xyz
|
|
Add support for pmk8550 compatible and lpg_data.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230407223849.17623-4-quic_amelende@quicinc.com
|
|
Certain PMICs like PMK8550 have a high resolution PWM module which can
support from 8-bit to 15-bit PWM. Add support for it.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230407223849.17623-3-quic_amelende@quicinc.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Various changes across the board, mostly improvements and cleanups"
* tag 'pwm/for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (42 commits)
pwm: pca9685: Convert to i2c's .probe_new()
pwm: sun4i: Propagate errors in .get_state() to the caller
pwm: Handle .get_state() failures
pwm: sprd: Propagate errors in .get_state() to the caller
pwm: rockchip: Propagate errors in .get_state() to the caller
pwm: mtk-disp: Propagate errors in .get_state() to the caller
pwm: imx27: Propagate errors in .get_state() to the caller
pwm: cros-ec: Propagate errors in .get_state() to the caller
pwm: crc: Propagate errors in .get_state() to the caller
leds: qcom-lpg: Propagate errors in .get_state() to the caller
drm/bridge: ti-sn65dsi86: Propagate errors in .get_state() to the caller
pwm/tracing: Also record trace events for failed API calls
pwm: Make .get_state() callback return an error code
pwm: pxa: Enable for MMP platform
pwm: pxa: Add reference manual link and limitations
pwm: pxa: Use abrupt shutdown mode
pwm: pxa: Remove clk enable/disable from pxa_pwm_config
pwm: pxa: Set duty cycle to 0 when disabling PWM
pwm: pxa: Remove pxa_pwm_enable/disable
pwm: mediatek: Add support for MT7986
...
|
|
.get_state() can return an error indication. Make use of it to propagate
failing hardware accesses.
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
.get_state() might fail in some cases. To make it possible that a driver
signals such a failure change the prototype of .get_state() to return an
error code.
This patch was created using coccinelle and the following semantic patch:
@p1@
identifier getstatefunc;
identifier driver;
@@
struct pwm_ops driver = {
...,
.get_state = getstatefunc
,...
};
@p2@
identifier p1.getstatefunc;
identifier chip, pwm, state;
@@
-void
+int
getstatefunc(struct pwm_chip *chip, struct pwm_device *pwm, struct pwm_state *state)
{
...
- return;
+ return 0;
...
}
plus the actual change of the prototype in include/linux/pwm.h (plus some
manual fixing of indentions and empty lines).
So for now all drivers return success unconditionally. They are adapted
in the following patches to make the changes easier reviewable.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
lpg_brighness_set() function can sleep, while led's brightness_set()
callback must be non-blocking. Change LPG driver to use
brightness_set_blocking() instead.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:580
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 0, name: swapper/0
preempt_count: 101, expected: 0
INFO: lockdep is turned off.
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 6.1.0-rc1-00014-gbe99b089c6fc-dirty #85
Hardware name: Qualcomm Technologies, Inc. DB820c (DT)
Call trace:
dump_backtrace.part.0+0xe4/0xf0
show_stack+0x18/0x40
dump_stack_lvl+0x88/0xb4
dump_stack+0x18/0x34
__might_resched+0x170/0x254
__might_sleep+0x48/0x9c
__mutex_lock+0x4c/0x400
mutex_lock_nested+0x2c/0x40
lpg_brightness_single_set+0x40/0x90
led_set_brightness_nosleep+0x34/0x60
led_heartbeat_function+0x80/0x170
call_timer_fn+0xb8/0x340
__run_timers.part.0+0x20c/0x254
run_timer_softirq+0x3c/0x7c
_stext+0x14c/0x578
____do_softirq+0x10/0x20
call_on_irq_stack+0x2c/0x5c
do_softirq_own_stack+0x1c/0x30
__irq_exit_rcu+0x164/0x170
irq_exit_rcu+0x10/0x40
el1_interrupt+0x38/0x50
el1h_64_irq_handler+0x18/0x2c
el1h_64_irq+0x64/0x68
cpuidle_enter_state+0xc8/0x380
cpuidle_enter+0x38/0x50
do_idle+0x244/0x2d0
cpu_startup_entry+0x24/0x30
rest_init+0x128/0x1a0
arch_post_acpi_subsys_init+0x0/0x18
start_kernel+0x6f4/0x734
__primary_switched+0xbc/0xc4
Fixes: 24e2d05d1b68 ("leds: Add driver for Qualcomm LPG")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
The leds-trigger-pattern documentation describes how the brightness of
the LED should transition linearly from one brightness value to the
next, over the given delta_t.
But the pattern engine in the Qualcomm LPG hardware only supports
holding the brightness for each entry for the period.
This subset of patterns can be represented in the leds-trigger-pattern
by injecting zero-time transitions after each entry in the pattern,
resulting in a pattern that pattern that can be rendered by the LPG.
Rework LPG pattern interface to require these zero-time transitions, to
make it comply with this subset of patterns and reject the patterns it
can't render.
Fixes: 24e2d05d1b68 ("leds: Add driver for Qualcomm LPG")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
Add pm8350c compatible and lpg_data to the driver.
Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
The Light Pulse Generator (LPG) is a PWM-block found in a wide range of
PMICs from Qualcomm. These PMICs typically comes with 1-8 LPG instances,
with their output being routed to various other components, such as
current sinks or GPIOs.
Each LPG instance can operate on fixed parameters or based on a shared
lookup-table, altering the duty cycle over time. This provides the means
for hardware assisted transitions of LED brightness.
A typical use case for the fixed parameter mode is to drive a PWM
backlight control signal, the driver therefor allows each LPG instance
to be exposed to the kernel either through the LED framework or the PWM
framework.
A typical use case for the LED configuration is to drive RGB LEDs in
smartphones etc, for which the driver supports multiple channels to be
ganged up to a MULTICOLOR LED. In this configuration the pattern
generators will be synchronized, to allow for multi-color patterns.
The idea of modelling this as a LED driver ontop of a PWM driver was
considered, but setting the properties related to patterns does not fit
in the PWM API. Similarly the idea of just duplicating the lower bits in
a PWM and LED driver separately was considered, but this would not allow
the PWM channels and LEDs to be configured on a per-board basis. The
driver implements the more complex LED interface, and provides a PWM
interface on the side of that, in the same driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org>
[On the Sony Xperia Nile Discovery, SDM630]
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
