| Age | Commit message (Collapse) | Author |
|---|
|
The power control function ignores the "on" argument when setting the
report ID, and thus is always sending HID_POWER_SLEEP. This causes a
problem when trying to wakeup.
Fix by sending the state variable, which contains the proper HID_POWER_ON or
HID_POWER_SLEEP based on the "on" argument.
Fixes: 3c98b8dbdced ("Input: cyttsp5 - implement proper sleep and wakeup procedures")
Cc: stable@vger.kernel.org
Signed-off-by: Mikael Gonella-Bolduc <mgonellabolduc@dimonoff.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20250423135243.1261460-1-hugo@hugovil.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The current reset pulse width is measured to be 5us on a
Renesas RZ/G2L SOM. The manufacturer's minimum reset pulse width is
specified as 10us.
Extend reset pulse width to make sure it is long enough on all platforms.
Also reword confusing comments about reset pin assertion.
Fixes: 5b0c03e24a06 ("Input: Add driver for Cypress Generation 5 touchscreen")
Cc: stable@vger.kernel.org
Acked-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20250410184633.1164837-1-hugo@hugovil.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove commas after the sentinel entries.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240509174158.2211071-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The Cypress touchscreen controllers are often used with external pull-up
for the interrupt line and the I2C lines, so we might need to enable
a regulator to bring the lines into usable state. Otherwise, this might
cause spurious interrupts and reading from I2C will fail.
Implement support for a "vddio-supply" that is enabled by the cyttsp5
driver so that the regulator gets enabled when needed.
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Acked-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20221117190507.87535-3-linmengbo0689@protonmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714174633.4058096-1-robh@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Sync up with mainline to bring in updates to shared infrastructure.
|
|
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517164645.162294-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The touchscreen can be put into a deep sleep state that prevents it from
emitting touch irqs. Put the touchscreen into deep sleep during suspend
if it is not marked as a wakeup source.
This also fixes a problem with the touchscreen getting unresponsive after
system resume when a falling edge trigger is used for the interrupt.
When left on during suspend, the touchscreen would pull the interrupt
line down in response to touch events, leaving the interrupt effectively
disabled after resume.
Signed-off-by: Maximilian Weigand <mweigand@mweigand.net>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20230504120316.408687-2-mweigand2017@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The cmd array should be initialized with the proper command size and not
with the actual command value that is sent to the touchscreen.
Signed-off-by: Maximilian Weigand <mweigand@mweigand.net>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20230501113010.891786-2-mweigand@mweigand.net
Fixes: 5b0c03e24a06 ("Input: Add driver for Cypress Generation 5 touchscreen")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The removed lines are remnants of the vendor driver and are not used in
the upstream driver.
Signed-off-by: Maximilian Weigand <mweigand@mweigand.net>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20230501113010.891786-3-mweigand@mweigand.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Prior to this patch, the sensing configuration data was not parsed
correctly, breaking detection of max_tch. The vendor driver includes
this field. This change informs the driver about the correct maximum
number of simultaneous touch inputs.
Tested on a Pine64 PineNote with a modified touch screen controller
firmware.
Signed-off-by: hrdl <git@hrdl.eu>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20230411211651.3791304-1-git@hrdl.eu
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Prior to this patch, the bitmask ends up being 0x3, as opposed to 0x1
which likely was the intention. The erroneous bit results in the driver
reporting 2 different button activations in designs with 2 or more
buttons.
To detect which button has been pressed, cyttsp5_btn_attention() uses a
for loop to iterate through the input buffer, while shifting and
applying a bitmask to determine the state for each button.
Unfortunately, when the bitmask is 0x3 and there are multiple buttons,
this procedure falls apart.
Consider a design with 3 buttons. Pressing the third button will result
in a call to cyttsp5_btn_attention() with the input buffer containing
0x4 (binary 0100). In the first iteration of the for loop cur_btn_state
will be:
(0x4 >> 0 * 1) & 0x3 = 0x4 & 0x3 = 0x0
This is correct. However, in the next iteration this happens:
(0x4 >> 1 * 1) & 0x3 = 0x2 & 0x3 = 0x2
Which means that a key event for key 1 is generated, even though it's
not really active. In the third iteration, the loop detects the button
that was actually pressed:
(0x4 >> 2 * 1) & 0x3 = 0x1 & 0x3 = 0x1
This key event is the only one that should have been detected, but it is
accompanied by the preceding key. Ensuring the applied mask is 0x1
solves this problem.
Signed-off-by: Richard Kjerstadius <richard.kjerstadius@teledyne.com>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20230127102903.3317089-1-richard.kjerstadius@teledyne.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-236-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This is the basic driver for the Cypress TrueTouch Gen5 touchscreen
controllers. This driver supports only the I2C bus but it uses regmap
so SPI support could be added later.
The touchscreen can retrieve some defined zone that are handled as
buttons (according to the hardware). That is why it handles
button and multitouch events.
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Tested-by: Andreas Kemnade <andreas@kemnade.info> # Kobo Clara HD
Tested-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20221026114908.191472-2-alistair@alistair23.me
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
