| Age | Commit message (Collapse) | Author |
|---|
|
Change the buffer disable callback from postdisable to predisable.
This balances the existing posteanble callback. Using postdisable
with posteanble can be problematic, for example, if update_scan_mode
fails, it would call postdisable without ever having called posteanble,
so the drivers using this would be in an unexpected state when
postdisable was called.
Fixes: af3008485ea0 ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250703-iio-adc-ad_sigma_delta-buffer-predisable-v1-1-f2ab85138f1f@baylibre.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add SPI offload support to the ad_sigma_delta module.
When the SPI controller has SPI offload capabilities, the module will
now use that for buffered reads instead of the RDY interrupt trigger.
Drivers that use the ad_sigma_delta module will have to opt into this
by setting supports_spi_offload since each driver will likely need
additional changes before SPI offload can be used. This will allow us
to gradually enable SPI offload support for each driver.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-11-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use spi_optimize_message() to improve the performance of buffered reads.
By setting up the SPI message and pre-optimizing it in the buffer
postenable callback, we can reduce overhead during each sample read.
A rough estimate shows that this reduced the CPU usage of the interrupt
handler thread from 22% to 16% using an EVAL-AD4112ARDZ board on a
DE10-Nano (measuring a single channel at the default 6.2 kHz sample
rate).
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-8-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Refactor code to set the read address in a separate function.
This code is already duplicated twice and we will need to use it a third
time in a later commit.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-7-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Drop linux/iio/sysfs.h since it is unused and replace linux/kernel.h
with more explicit headers. There are a couple of other headers added
weren't covered by kernel.h, like linux/gpio/consumer.h that are added
since the module makes use of those APIs as well.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-6-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use the BITS_TO_BYTES() macro instead of dividing by 8 to convert bits
to bytes.
This makes it more obvious what unit conversion is taking place.
In one instance, we also avoid the temporary assignment to a variable
as it was confusing that reg_size was being used with two different
units (bits and bytes).
scan_type is factored out to reduce line wrapping.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-5-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use sizeof() instead of hardcoding the size of the timestamp in the
ALIGN() macro. This makes it a bit more obvious what the intention of
the code is.
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-4-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Replace uint8_t with u8 in the ad_sigma_delta driver.
Technically, uint8_t comes from the C standard library, while u8 is a
Linux kernel type. Since we don't use the C standard library in the
kernel, we should use the kernel types instead.
There is also one instance where int64_t is replaced with s64.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-3-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Sort includes in alphabetical order and fix grouping before we add more.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-2-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix overallocating the size of the scan buffer by converting bits to
bytes. The size is meant to be in bytes, so scanbits needs to be
divided by 8.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250701-iio-adc-ad7173-add-spi-offload-support-v3-1-42abb83e3dac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix Smatch-detected issue:
drivers/iio/adc/ad_sigma_delta.c:604 ad_sd_trigger_handler() error:
uninitialized symbol 'status_pos'.
The variable `status_pos` was only initialized in specific switch cases
(1, 2, 3, 4), which could leave it uninitialized if `reg_size` had an
unexpected value.
Fix by adding a default case to the switch block to catch unexpected
values of `reg_size`. Use `dev_err_ratelimited()` for error logging and
`goto irq_handled` instead of returning early.
Signed-off-by: Purva Yeshi <purvayeshi550@gmail.com>
Link: https://patch.msgid.link/20250410170408.8585-1-purvayeshi550@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
All other calls to ad_sigma_delta_set_channel() in ad_sigma_delta.c
check the return value afterwards. Do it for all calls.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-16-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The function ad_sd_calibrate() enables the channel to calibrate at
function entry but doesn't disable it on exit. This is problematic
because if two (or more) channels are calibrated in a row, the second
calibration isn't executed as intended as the first (still enabled)
channel is recalibrated and after the first irq (i.e. when the
calibration of the first channel completed) the calibration is aborted.
This currently affects ad7173 only, as the other drivers using
ad_sd_calibrate() never have more than one channel enabled at a time.
To fix this, disable the calibrated channel after calibration.
Fixes: 031bdc8aee01 ("iio: adc: ad7173: add calibration support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-11-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
iio_device_claim/release_direct()
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
This is a complex function with a lot more than the release of direct
mode to unwind on error. As such no attempt made to factor out
the inner code.
Cc: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-21-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Move the call to fwnode_irq_get_byname() from the driver-specific
ad7173_fw_parse_device_config() to the shared ad_sd_init() function.
The main reason for this is that we want struct ad_sigma_delta_info to
be static const data that describes the actual ADC chip, not the
application-specific configuration or any runtime state.
Previously, this struct was being used to pass the IRQ number to the
shared ad_sd_init() function. Now, this is replaced by a boolean flag
that is set at compile time and the ad_sd_init() function handles
looking up the IRQ number instead. This also has the added benefit that
if any other drivers need to make use of this in the future, they just
have to set the flag and the shared code will take care of the rest
rather than duplicating the code in each driver.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250113-iio-adc-ad7313-fix-non-const-info-struct-v4-1-b63be3ecac4a@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This fixes a checkpatch warning:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
#70: FILE: drivers/iio/adc/ad_sigma_delta.c:253:
+ unsigned status_reg;
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20241218114809.1378063-2-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
It can happen if a previous conversion was aborted the ADC pulls down
the R̅D̅Y̅ line but the event wasn't handled before. In that case enabling
the irq might immediately fire (depending on the irq controller
capabilities) and even with a rdy-gpio isn't identified as an unrelated
one.
To cure that problem check for a pending event before the measurement is
started and clear it if needed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/3ec6b61fb1e527e935133dc56f589aab4b2094a3.1733504533.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The various chips can be reset using a sequence of SPI transfers with
MOSI = 1. The length of such a sequence varies from chip to chip. Store
that length in struct ad_sigma_delta_info and replace the respective
parameter to ad_sd_reset() with it.
Note the ad7192 used to pass 48 as length but the documentation
specifies 40 as the required length. Assuming the latter is right.
(Using a too long sequence doesn't hurt apart from using a longer spi
transfer than necessary, so this is no relevant fix.)
The motivation for storing this information is that this is useful to
clear a pending R̅D̅Y̅ signal in the next change.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/9750db62fce638bf140ff48172c23bff7f785e5b.1733504533.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ad_sigma_delta driver helper uses irq_disable_nosync(). With that
one it is possible that the irq handler still runs after the
irq_disable_nosync() function call returns. Also to properly synchronize
irq disabling in the different threads proper locking is needed and
because it's unclear if the irq handler's irq_disable_nosync() call
comes first or the one in the enabler's error path, all code locations
that disable the irq must check for .irq_dis first to ensure there is
exactly one disable call per enable call.
So add a spinlock to the struct ad_sigma_delta and use it to synchronize
irq enabling and disabling. Also only act in the irq handler if the irq
is still enabled.
Fixes: af3008485ea0 ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/9e6def47e2e773e0e15b7a2c29d22629b53d91b1.1733504533.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
ad_sd_read_reg_raw()
When struct ad_sigma_delta::keep_cs_asserted was introduced only
register writing was adapted to honor this new flag. Also respect it
when reading a register.
Fixes: df1d80aee963 ("iio: ad_sigma_delta: Properly handle SPI bus locking vs CS assertion")
Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/8d76b4ea4a4363b269886c71193b840821c724ea.1733504533.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Some of the ADCs by Analog signal their irq condition on the MISO line.
So typically that line is connected to an SPI controller and a GPIO. The
GPIO is used as input and the respective interrupt is enabled when the
last SPI transfer is completed.
Depending on the GPIO controller the toggling MISO line might make the
interrupt pending even while it's masked. In that case the irq handler
is called immediately after irq_enable() and so before the device
actually pulls that line low which results in non-sense values being
reported to the upper layers.
The only way to find out if the line was actually pulled low is to read
the GPIO. (There is a flag in AD7124's status register that also signals
if an interrupt was asserted, but reading that register toggles the MISO
line and so might trigger another spurious interrupt.)
Add the possibility to specify an interrupt GPIO in the machine
description in addition to the plain interrupt. This GPIO is used then
to check if the irq line is actually active in the irq handler.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/5be9a4cc4dc600ec384c88db01dd661a21506b9c.1733504533.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Clean up the existing export namespace code along the same lines of
commit 33def8498fdd ("treewide: Convert macro and uses of __section(foo)
to __section("foo")") and for the same reason, it is not desired for the
namespace argument to be a macro expansion itself.
Scripted using
git grep -l -e MODULE_IMPORT_NS -e EXPORT_SYMBOL_NS | while read file;
do
awk -i inplace '
/^#define EXPORT_SYMBOL_NS/ {
gsub(/__stringify\(ns\)/, "ns");
print;
next;
}
/^#define MODULE_IMPORT_NS/ {
gsub(/__stringify\(ns\)/, "ns");
print;
next;
}
/MODULE_IMPORT_NS/ {
$0 = gensub(/MODULE_IMPORT_NS\(([^)]*)\)/, "MODULE_IMPORT_NS(\"\\1\")", "g");
}
/EXPORT_SYMBOL_NS/ {
if ($0 ~ /(EXPORT_SYMBOL_NS[^(]*)\(([^,]+),/) {
if ($0 !~ /(EXPORT_SYMBOL_NS[^(]*)\(([^,]+), ([^)]+)\)/ &&
$0 !~ /(EXPORT_SYMBOL_NS[^(]*)\(\)/ &&
$0 !~ /^my/) {
getline line;
gsub(/[[:space:]]*\\$/, "");
gsub(/[[:space:]]/, "", line);
$0 = $0 " " line;
}
$0 = gensub(/(EXPORT_SYMBOL_NS[^(]*)\(([^,]+), ([^)]+)\)/,
"\\1(\\2, \"\\3\")", "g");
}
}
{ print }' $file;
done
Requested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://mail.google.com/mail/u/2/#inbox/FMfcgzQXKWgMmjdFwwdsfgxzKpVHWPlc
Acked-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Linux 6.12-rc2
Resolved movement of asm/unaligned.h to linux/unaligned.h
|
|
This commit fixes several typographical errors in comments within
the drivers/iio/adc directory. No functional changes are made.
Detected using codespell.
Signed-off-by: Yu Jiaoliang <yujiaoliang@vivo.com>
Link: https://patch.msgid.link/20240926034411.3482986-1-yujiaoliang@vivo.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
We need the char-misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With commit 7b0c9f8fa3d2 ("iio: adc: ad_sigma_delta: Add optional irq
selection"), we can get the irq line from struct ad_sigma_delta_info
instead of the spi device. However, in devm_ad_sd_probe_trigger(), when
getting the irq_flags with irq_get_trigger_type() we are still using
the spi device irq instead of the one used for devm_request_irq().
Fixes: 7b0c9f8fa3d2 ("iio: adc: ad_sigma_delta: Add optional irq selection")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240806-dev-fix-ad-sigma-delta-v1-1-aa25b173c063@analog.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Make use of iio_get_masklength) and iio_for_each_active_channel() to
access '.masklength' so it can be annotated as __private when there
are no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Alexandru Ardelean <aardelean@baylibre.com>
Link: https://patch.msgid.link/20240702-dev-iio-masklength-private-v1-17-98193bf536a6@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Sigma delta ADCs with a sequencer need to disable the previously enabled
channel when reading using ad_sigma_delta_single_conversion(). This was
done manually in drivers for devices with sequencers.
This patch implements handling of single channel disabling after a
single conversion.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Dumitru Ceclan <dumitru.ceclan@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240607-ad4111-v7-3-97e3855900a0@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
wait_for_completion_timeout()
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240429113313.68359-2-wsa+renesas@sang-engineering.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add optional irq_num attribute to ad_sigma_delta_info structure for
selecting the used interrupt line for ADC's conversion completion.
Signed-off-by: Dumitru Ceclan <mitrutzceclan@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240228110622.25114-2-mitrutzceclan@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver subsystem updates from Greg KH:
"Here is the big set of char/misc and a number of other driver
subsystem updates for 6.9-rc1. Included in here are:
- IIO driver updates, loads of new ones and evolution of existing ones
- coresight driver updates
- const cleanups for many driver subsystems
- speakup driver additions
- platform remove callback void cleanups
- mei driver updates
- mhi driver updates
- cdx driver updates for MSI interrupt handling
- nvmem driver updates
- other smaller driver updates and cleanups, full details in the
shortlog
All of these have been in linux-next for a long time with no reported
issue, other than a build warning for the speakup driver"
The build warning hits clang and is a gcc (and C23) extension, and is
fixed up in the merge.
Link: https://lore.kernel.org/all/20240321134831.GA2762840@dev-arch.thelio-3990X/
* tag 'char-misc-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (279 commits)
binder: remove redundant variable page_addr
uio_dmem_genirq: UIO_MEM_DMA_COHERENT conversion
uio_pruss: UIO_MEM_DMA_COHERENT conversion
cnic,bnx2,bnx2x: use UIO_MEM_DMA_COHERENT
uio: introduce UIO_MEM_DMA_COHERENT type
cdx: add MSI support for CDX bus
pps: use cflags-y instead of EXTRA_CFLAGS
speakup: Add /dev/synthu device
speakup: Fix 8bit characters from direct synth
parport: sunbpp: Convert to platform remove callback returning void
parport: amiga: Convert to platform remove callback returning void
char: xillybus: Convert to platform remove callback returning void
vmw_balloon: change maintainership
MAINTAINERS: change the maintainer for hpilo driver
char: xilinx_hwicap: Fix NULL vs IS_ERR() bug
hpet: remove hpets::hp_clocksource
platform: goldfish: move the separate 'default' propery for CONFIG_GOLDFISH
char: xilinx_hwicap: drop casting to void in dev_set_drvdata
greybus: move is_gb_* functions out of greybus.h
greybus: Remove usage of the deprecated ida_simple_xx() API
...
|
|
Make sure we can specify the IRQ trigger type from firmware and drivers
won't ignore it. In fact, this how it should be done but since someone
might be already depending on the driver to hardcode the trigger type
(and not specifying it in firmware), let's do it like this so there's
no possible breakage.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240117-dev_sigma_delta_no_irq_flags-v1-2-db39261592cf@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In commit 8caab75fd2c2 ("spi: Generalize SPI "master" to "controller"")
some functions and struct members were renamed. To not break all drivers
compatibility macros were provided.
To be able to remove these compatibility macros push the renaming into
this driver.
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/de866d09c80c89816df62602ba4ba8ba30e9971f.1707324794.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Sigma-Delta ADCs supported by this driver can use SDO as an interrupt
line to indicate the completion of a conversion. However, some devices
cannot properly detect the completion of a conversion by an interrupt.
This is for the reason mentioned in the following commit.
commit e9849777d0e2 ("genirq: Add flag to force mask in
disable_irq[_nosync]()")
A read operation is performed by an extra interrupt before the completion
of a conversion. At this time, the value read from the ADC data register
is the same as the previous conversion result. This patch fixes the issue
by setting IRQ_DISABLE_UNLAZY flag.
Fixes: 0c6ef985a1fd ("iio: adc: ad7791: fix IRQ flags")
Fixes: 1a913270e57a ("iio: adc: ad7793: Fix IRQ flag")
Fixes: e081102f3077 ("iio: adc: ad7780: Fix IRQ flag")
Fixes: 89a86da5cb8e ("iio: adc: ad7192: Add IRQ flag")
Fixes: 79ef91493f54 ("iio: adc: ad7124: Set IRQ type to falling")
Signed-off-by: Masahiro Honda <honda@mechatrax.com>
Link: https://lore.kernel.org/r/20230518110816.248-1-honda@mechatrax.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Drop 'mlock' usage by making use of iio_device_claim_direct_mode().
This change actually makes sure we cannot do a single conversion while
buffering is enable. Note there was a potential race in the previous
code since we were only acquiring the lock after checking if the bus is
enabled.
Fixes: af3008485ea0 ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: <Stable@vger.kernel.org> #No rush as race is very old.
Link: https://lore.kernel.org/r/20220920112821.975359-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Some sigma-delta chips support sampling of multiple
channels in continuous mode.
When the operating with more than one channel enabled,
the channel sequencer cycles through the enabled channels
in sequential order, from first channel to the last one.
If a channel is disabled, it is skipped by the sequencer.
If more than one channel is used in continuous mode,
instruct the device to append the status to the SPI transfer
(1 extra byte) every time we receive a sample.
All sigma-delta chips possessing a sampling sequencer have
this ability. Inside the status register there will be
the number of the converted channel. In this way, even
if the CPU won't keep up with the sampling rate, it won't
send to userspace wrong channel samples.
When multiple channels are enabled in continuous mode,
the device needs to perform a measurement on all slots
before we can push to userspace the sample.
If, during sequencing and data reading, a channel measurement
is lost, a desync occurred. In this case, ad_sigma_delta drops
the incomplete sample and waits for the device to send the
measurement on the first active slot.
Co-developed-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20220322105029.86389-5-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In order to avoid unnecessary pollution of the global symbol namespace
move the core/library functions into a specific namespace and import
that into the various specific device drivers that use them.
For more information see https://lwn.net/Articles/760045/
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Renato Lui Geh <renatogeh@gmail.com>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220130205701.334592-2-jic23@kernel.org
|
|
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-3-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Since all AD Sigma-Delta drivers now use the
devm_ad_sd_setup_buffer_and_trigger() function, we can remove the old
ad_sd_{setup,cleanup}_buffer_and_trigger() functions.
This way we can discourage new drivers that use the ad_sigma_delta
lib-driver to use these (older functions).
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-13-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This is a version of ad_sd_setup_buffer_and_trigger() with all underlying
functions (that are used) being replaced with their device-managed
variants.
One thing to take care here is with {devm_}iio_trigger_alloc(), where both
functions take a parent-device object as the first parameter.
To make sure nothing quirky is happening, the devm_ad_sd_probe_trigger()
function is checking that the provided 'dev' reference is the same as the
one stored on the 'struct ad_sigma_delta' driver data.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-6-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Continuing from Alexandru Ardelean's introduction of the split between
driver modifiable fields and those that should only be set by the core.
This could have been done in two steps to make the actual move after
introducing iio_device_id() but there seemed limited point to that
given how mechanical the majority of the patch is.
Includes fixup from Alex for missing mxs-lradc-adc conversion.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210426174911.397061-2-jic23@kernel.org
|
|
These devices are not able to mask the signal used as a data ready
interrupt. As such they previously requested the irq then immediately
disabled it. Now we can avoid the potential of a spurious interrupt
by avoiding the irq being auto enabled in the first place.
I'm not sure how this code could have been called with the irq already
disabled, so I believe the conditional would always have been true and
have removed it.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Alexandru Ardelean <ardeleanalex@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20210402184544.488862-8-jic23@kernel.org
|
|
When allocated with [devm_]iio_trigger_alloc(), set trig device parent to
the device the trigger is allocated for by default.
It can always be reassigned in the probe routine.
Change iio_trigger_alloc() API to add the device pointer to be coherent
with devm_iio_trigger_alloc, using similar interface to
iio_device_alloc().
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210309193620.2176163-2-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use a heap allocated memory for the SPI transfer buffer. Using stack memory
can corrupt stack memory when using DMA on some systems.
This change moves the buffer from the stack of the trigger handler call to
the heap of the buffer of the state struct. The size increases takes into
account the alignment for the timestamp, which is 8 bytes.
The 'data' buffer is split into 'tx_buf' and 'rx_buf', to make a clearer
separation of which part of the buffer should be used for TX & RX.
Fixes: af3008485ea03 ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201124123807.19717-1-alexandru.ardelean@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/ad_sigma_delta.c: In function ‘ad_sd_trigger_handler’:
drivers/iio/adc/ad_sigma_delta.c:405:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
405 | int ret;
| ^~~
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
All devices using a triggered buffer need to attach and detach the trigger
to the device in order to properly work. Instead of doing this in each and
every driver by hand move this into the core.
At this point in time, all drivers should have been resolved to
attach/detach the poll-function in the same order.
This patch removes all explicit calls of iio_triggered_buffer_postenable()
& iio_triggered_buffer_predisable() in all drivers, since the core handles
now the pollfunc attach/detach.
The more peculiar change is for the 'at91-sama5d2_adc' driver, since it's
not immediately obvious that removing the hooks doesn't break anything.
Eugen was able to test on at91-sama5d2-adc driver, sama5d2-xplained board.
All seems to be fine.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com> #for at91-sama5d2-adc
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This makes the driver code slightly easier to read.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Before this patch the ad_sigma_delta implementation hardcoded
the irq trigger type to low, assuming that all Sigma-Delta ADCs
have the same interrupt-type.
This patch allows all drivers using the ad_sigma_delta layer to set the
irq trigger type to the one specified in the datasheet.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch exports the ad_sd_calibrate function in order to be able to
call it from outside ad_sigma_delta.
There are cases where the option to calibrate one channel at a time is
necessary (ex. system calibration for zero scale and full scale).
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
