summaryrefslogtreecommitdiff
path: root/drivers/gpu/drm/i915/display/intel_dpll.c
AgeCommit message (Collapse)Author
2023-06-07drm/i915/dpll: drop unused but set variables bestn and bestm1Jani Nikula
Prepare for re-enabling -Wunused-but-set-variable. Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Jouni Högander <jouni.hogander@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/a85ccc8c0f451fcb997b4ac138dbeba2a653cebe.1685119007.git.jani.nikula@intel.com
2023-05-15drm/i915/display: add i915 parameter to I915_STATE_WARN()Jani Nikula
Add i915 parameter to I915_STATE_WARN() and use device based logging. Done using cocci + hand edited where there was no i915 local variable ready. v2: avoid null deref in verify_connector_state() Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230512181658.1735594-1-jani.nikula@intel.com
2023-04-28drm/i915/mtl: C20 port clock calculationMika Kahola
Calculate port clock with C20 phy. BSpec: 64568 Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-5-mika.kahola@intel.com
2023-04-14drm/i915/mtl: Add Support for C10 PHY message bus and pll programmingRadhakrishna Sripada
XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-01-18drm/i915: move chv_dpll_md and bxt_phy_grc to display sub-struct under stateJani Nikula
Move the display related members to the struct drm_i915_private display sub-struct. Put them under "state", as they are related to storing values that aren't readable from the hardware, to appease the state checker. Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230117143946.2426043-3-jani.nikula@intel.com
2022-11-11drm/i915: stop including i915_irq.h from i915_trace.hJani Nikula
Turns out many of the files that need i915_reg.h get it implicitly via {display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h -> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h, makes sense to drop it, but that requires adding quite a few new includes all over the place. Prefer including i915_reg.h where needed instead of adding another implicit include, because eventually we'll want to split up i915_reg.h and only include the specific registers at each place. Also some places actually needed i915_irq.h too. Cc: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
2022-11-03drm/i915/dpio: un-inline the vlv phy/channel mapping functionsJani Nikula
Simplify the heavy intel_display_types.h header. Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/943dd3e9812138b1cf3ddcfde896cfec006f3847.1667383630.git.jani.nikula@intel.com
2022-09-13drm/i915: Fix TV encoder clock computationVille Syrjälä
The TV encoder has its own special clocking strategy, which means we can't just use intel_crtc_dotclock() to figure out what the resulting dotclock will be given the actual DPLL port_clock. Additionally the DPLL can't always generate exactly the frequency we initially asked for. This results in us computing a bogus dotclock/etc., and it won't match the readout which is handled by the encoder itself properly. Naturally the state checker becomes unhappy with the mismatch. To do this sanely we'll need to move the DPLL computation into encoder->compute_config() so that all the derived state gets correctly computed based on the actual DPLL output frequency. Start doing that just for the TV encoder initally as intel_crtc_dotclock() should be able to handle other encoder types well enough. Though eventually this should be done for all encoder types rather than doing it from intel_crtc_compute_config(). With this we actually do some of the DPLL state computation twice, but we can skip the second actual .find_dpll() search by flagging .clock_set=true after we've done it once. We also still need to avoid clobbering the correct adjusted_mode.crtc_clock set up by encoder->compute_config() when called a second time from intel_crtc_compute_config(). Fixes: 665a7b04092c ("drm/i915: Feed the DPLL output freq back into crtc_state") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220909205932.32537-1-ville.syrjala@linux.intel.com Acked-by: Jani Nikula <jani.nikula@intel.com>
2022-09-08drm/i915: Feed the DPLL output freq back into crtc_stateVille Syrjälä
Fill port_clock and hw.adjusted_mode.crtc_clock with the actual frequency we're going to be getting from the hardware. This will let us accurately compute all derived state that depends on those. v2: Reintroduce iCLKIP WARN v3: Try to deal with VLV/BXT DSI PLL as well Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-8-ville.syrjala@linux.intel.com
2022-09-08drm/i915: Reassign DPLLs only for crtcs going throug .compute_config()Ville Syrjälä
Only reassign the pipe's DPLL if it's going through a full .compute_config() cycle. If OTOH it's just getting modeset eg. in order to change cdclk there doesn't seem much point in picking a new DPLL for it. This should also prevent .get_dplls() from seeing a funky port_clock for DP even in cases where the readout produces a non-standard clock and we (for some reason) have decided to not fully recompute the state to remedy the situation. Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-7-ville.syrjala@linux.intel.com
2022-09-08drm/i915: Do .crtc_compute_clock() earlierVille Syrjälä
Currently we calculate a lot of things (pixel rate, watermarks, cdclk) trusting that the DPLL can generate the exact frequency we ask it. In practice that is not true and there can be certain amount of rounding involved. To allow us to eventually get accurate numbers for all our DPLL clock derived state we need to move the DPLL calculation to hapen much earlier. To that end we hoist it up to the just after the fastset checks. For now we just do the easy code motion, and the actual back feeding of the final DPLL clock into the state will come later. A slight change here is that now .crtc_compute_clock() can get called while the shared_dpll is still assigned. But since .crtc_compute_clock() no longer assignes new shared_dplls this is perfectly fine. TODO: I'd actually like to do this before the fastset check so that if the DPLL state should change we actually do the modeset. Which I think is what the video aficionados want, but it might not be what the fans of fastboot want. Not yet sure how to reconcile those conflicting requirements... v2: s/return/goto/ in error handling Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-6-ville.syrjala@linux.intel.com
2022-08-31drm/i915: move vbt to display.vbtJani Nikula
Move display VBT related members under drm_i915_private display sub-struct. v2: Rebase Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/db4b648b201ea0b79654fec2028120999a735db0.1661779055.git.jani.nikula@intel.com
2022-08-29drm/i915: move dpll_funcs to display.funcsJani Nikula
Move display dpll functions under drm_i915_private display sub-struct. Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/5bf7aada2c7f0500c5002fa089fb66a92019a301.1661346845.git.jani.nikula@intel.com
2022-05-31drm/i915: Clean up DPLL related debugsVille Syrjälä
The debugs in lower level DPLL code don't really provide any useful extra information AFAICS. Better just streamline the code and just put the necessary debugs (to identify at which step the modeset failed) into the higher level code. In addition we'll get the full state dump as well, which should hopefully have enough information to figure out what went wrong. Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220503182242.18797-4-ville.syrjala@linux.intel.com
2022-05-31drm/i915: Split shared dpll .get_dplls() into compute and get phasesVille Syrjälä
Split the DPLL state computation into a separate function from the current .get_dplls() which currently serves a dual duty by also reserving the shared DPLLs. v2: s/false/-EINVAL/ (Jani) Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220503182242.18797-2-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2022-04-25drm/i915: Add crtc .crtc_get_shared_dpll()Ville Syrjälä
Start splitting the .compute_crtc_clock() into two parts; one part does the computation, the second part does the shared dpll assignment. I want to move the actual computation part much earlier into the compute_config() phase. v2: dg2_crtc_get_shared_dpll() not needed (Jani) Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220325123205.22140-10-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2022-04-25drm/i915: Split out dg2_crtc_compute_clock()Ville Syrjälä
DG2 doesn't currently used the shared_dpll stuff so let's just split it out from hsw_crtc_compute_clock() entirely. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220325123205.22140-9-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2022-04-25drm/i915: Clear the dpll_hw_state when disabling a pipeVille Syrjälä
Clear the dpll_hw_state when we're about disable the pipe. Previously it looks like we just left the old junk in there. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220325123205.22140-8-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2022-04-25drm/i915: Move the dpll_hw_state clearing to intel_dpll_crtc_compute_clock()Ville Syrjälä
All .crtc_compute_clock() implementations do the same memset() to clear the dpll_hw_state (since we preserve it across intel_crtc_prepare_cleared_state()). Move the memset() to the common wrapper. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220325123205.22140-7-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2022-04-25drm/i915: Move stuff into intel_dpll_crtc_compute_clock()Ville Syrjälä
Move some checks into intel_dpll_crtc_compute_clock() from the caller. Avoids the caller from having to worry about all this crap. We'll also reorder the hw.enable vs. shared_dpll checks since it makes sense to sanity check that we've cleared out the old shared_dpll even if the pipe is getting disabled. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220325123205.22140-6-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2022-04-25drm/i915: Adjust .crtc_compute_clock() calling conventionVille Syrjälä
Pass the full atomic state+crtc rather than the redundant crtc+crtc_state pair. We already need the full atomic state in the hsw+ codepath anyway. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220325123205.22140-5-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2022-04-25drm/i915: Make .get_dplls() return intVille Syrjälä
Get rid of the confusing back and forth between bools and ints in the .get_dplls() stuff. Just make everything return an int. Initial conversion done with cocci, with some manual fixups on top: @find@ identifier func !~ "get_hw_state|_is_|needed"; typedef bool; parameter list[N] P; @@ - bool + int func(P) { <... ( - return true; + return 0; | - return false; + return -EINVAL; ) ...> } @@ identifier find.func; expression list[find.N] E; expression X; @@ - if (!func(E)) + ret = func(E); + if (ret) { ... - return X; + return ret; } @@ identifier find.func; expression X; expression list[find.N] E; @@ - if (!func(E)) + ret = func(E); + if (ret) - return X; + return ret; @@ identifier find.func; expression list[find.N] E; expression O, X; typedef bool; bool B; @@ - B = func(E); - if (O && !B) + if (O) { + ret = func(E); + if (ret) - return X; + return ret; + } @@ identifier find.func; expression list[find.N] E; expression O, X; @@ - if (O && !func(E)) + if (O) { + ret = func(E); + if (ret) - return X; + return ret; + } @@ identifier find.func; expression list[find.N] E; expression X; typedef bool; bool B; @@ - B = func(E); - if (!B) + ret = func(E); + if (ret) { ... - return X; + return ret; } Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220325123205.22140-2-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2022-03-10drm/i915: Populate bxt/glk DPLL clock limits a bit moreVille Syrjälä
Set the bxt/glk DPLL min dotclock to 25MHz (HDMI minimum) and the max to 594 MHz (HDMI max). The supported DP frequencies (162MHz-540MHz) fit within the same range. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220307233940.4161-8-ville.syrjala@linux.intel.com Acked-by: Jani Nikula <jani.nikula@intel.com>
2022-03-10drm/i915: Remove redundant/wrong commentsVille Syrjälä
Remove the comment specifying the exact formulat for calculating the DPLL frequency from the *_find_best_dpll() functions. Each platform variant has its own way to calculate these and we have the code already to do that. These comments are entirely redundant and often even wrong so just get rid of them. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220307233940.4161-3-ville.syrjala@linux.intel.com Acked-by: Jani Nikula <jani.nikula@intel.com>
2022-03-10drm/i915: Store the /5 target clock in struct dpll on vlv/chvVille Syrjälä
Unify vlv/chv with earlier platforms so that the sturct dpll::dot represents the /5 clock frequency (ie. DP symbol rate or HDMI TMDS rate) rather than the *5 fast clock (/2 of the bitrate). Makes life a little less confusing to get the same number back in .dot which we fed into the DPLL algorithm. v2: Actually just include the 5x in the final P divider Do the same change to the hand rolled gvt code v3: Missed a few *5 in *_find_best_dpll() Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220309214301.22899-1-ville.syrjala@linux.intel.com
2022-03-02drm/i915: Use str_on_off()Lucas De Marchi
Remove the local onoff() implementation and adopt the str_on_off() from linux/string_helpers.h. Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220225234631.3725943-4-lucas.demarchi@intel.com
2022-02-09drm/i915/dpll: hide struct intel_dpll_funcsJani Nikula
The struct is only needed in intel_dpll.c, move it there. Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/fedb27386cbad2b162d83a706273dd8ad9e8eed2.1643896905.git.jani.nikula@intel.com
2022-02-09drm/i915/dpll: add intel_dpll_crtc_compute_clock()Jani Nikula
Avoid referencing the function pointer directly to be able to abstract the call better. Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/12ac40c1ef9915fe680c6657b603b08be022626b.1643896905.git.jani.nikula@intel.com
2021-12-02drm/i915/crtc: rename intel_get_crtc_for_pipe() to intel_crtc_for_pipe()Jani Nikula
The "get" in the name implies reference counting, remove it. This also makes the function conform to naming style. Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/6105d0ff44efac3c999af6382e4b0729e251f1e1.1638366969.git.jani.nikula@intel.com
2021-10-14drm/i915: split out vlv sideband to a separate fileJani Nikula
The VLV/CHV sideband code is pretty distinct from the rest of the sideband code. Split it out to new vlv_sideband.[ch]. Pure code movement with relevant #include changes, and a tiny checkpatch fix on top. Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/755ebbbaf01fc6d306b763b6ef60f45e671ba290.1634119597.git.jani.nikula@intel.com
2021-10-01drm/i915/dpll: move dpll modeset asserts to intel_dpll.cJani Nikula
Keep the functionality and the assert code together. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/0229659fb8af6c91c774408c6f7bb8c4ff8735e3.1632992608.git.jani.nikula@intel.com
2021-10-01drm/i915/pps: move pps (panel) modeset asserts to intel_pps.cJani Nikula
Move assert_panel_unlocked() to intel_pps.c and rename assert_pps_unlocked(). Keep the functionality and the assert code together. There's still a bit of a split between the eDP PPS usage in intel_pps.c and all the other PPS usage, and assert_pps_unlocked() is arguably more related to the latter. However, intel_pps.c is the best fit for anything touching the PPS registers. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/a9b77692a145891789eefb0447e082cfc22aaa85.1632992608.git.jani.nikula@intel.com
2021-09-29drm/i915: constify the dpll clock vtableDave Airlie
Most the dpll vtable into read-only memory. Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/0414a27317de3f335a8453a29486b746aa6862e7.1632869550.git.jani.nikula@intel.com
2021-09-29drm/i915: split the dpll clock compute out from display vtable.Dave Airlie
this single function might be possible to merge later, but for now it's simple to just split it out. Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/ba570aa10b694b2e8640e0c58430fd0053c306b7.1632869550.git.jani.nikula@intel.com
2021-09-15drm/i915: s/pipe/transcoder/ when dealing with PIPECONF/TRANSCONFVille Syrjälä
PIPECONF becamse TRANSCONF when HSW introduced the EDP transcoder. Bigjoiner is making life even more confusing by introducing a N:1 relationship between pipes and transcoders. In that case we only enable/configure the transcoder corresponding to the master pipe. Let's do some renames to make it clear we're dealing with the transcoder rather than pipe when it comes to PIPECONF/TRANSCONF. I decided to leave the _cpu_ part out from the function/macro names since the PCH transcoder related stuff already has a _pch_ in their name. So shouldn't be possible to confuse them. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-6-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2021-09-15drm/i915: Flatten hsw_crtc_compute_clock()Ville Syrjälä
hsw_crtc_compute_clock() has become spaghetti. Flatten it a bit to make it at least semi-legible. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-5-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2021-08-25drm/i915: Fold i9xx_set_pll_dividers() into i9xx_enable_pll()Ville Syrjälä
Can't think of a good reason why we'd need to program the FP dividers so early. Let's just do it when programming the rest of the DPLL. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-12-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2021-08-25drm/i915: Reuse ilk_needs_fb_cb_tune() for the reduced clock as wellVille Syrjälä
Use ilk_needs_fb_cb_tune() for reduced_clock instead of hand rolling it. Also ilk_needs_fb_cb_tune() can just use the precomputed M value instead of calculating it again. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-11-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2021-08-25drm/i915: Call {vlv,chv}_prepare_pll() from {vlv,chv}_enable_pll()Ville Syrjälä
We always call the vlv/chv prepare_pll() just before enable_pll(). Move the calls into the enable_pll() funcs. We can also consolidate the DPLL_VCO_ENABLE checks while at it. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-10-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2021-08-25drm/i915: Program DPLL P1 dividers consistentlyVille Syrjälä
On g4x and pch the DPLL has two P1 dividers (for refresh rate switching). Program the FPx1 P1 divider consistently to the reduced clock P1 divider if available, otherwise just program it to the same value as the FPx0 P1 divider. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-9-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2021-08-25drm/i915: Remove the 'reg' local variableVille Syrjälä
Get rid of the local 'reg' variable for the DPLL control register in i9xx_enable_pll(). We have other registers in there too so this is just making things more confusing. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-8-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2021-08-25drm/i915: Clean up variable names in old dpll functionsVille Syrjälä
s/pipe_config/crtc_state/ in the DPLL code. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-7-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2021-08-25drm/i915: Clean dpll calling conventionVille Syrjälä
Stop passing both the crtc and its state to the DPLL functions. The state alone is enough. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-6-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2021-08-25drm/i915: Constify struct dpll all overVille Syrjälä
Lots of places don't need to modify the DPLL params, so make them const. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-5-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2021-08-25drm/i915: Extract ilk_update_pll_dividers()Ville Syrjälä
Make the PCH dpll code match the gmch code by splitting the FP register handling out from ilk_compute_dpll(). Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-4-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2021-08-25drm/i915: Set output_types to EDP for vlv/chv DPLL forcingVille Syrjälä
When we enable the DPLL for the PPS kick, let's tell the DPLL code we're dealing with an eDP output. This shouldn't really matter, but it's more consistent with the way the DPLL is configured when we're actually enabling the eDP port for real. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-2-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2021-07-29drm/i915/dg2: Add MPLLB programming for SNPS PHYMatt Roper
DG2's SNPS PHYs incorporate a dedicated port PLL called MPLLB which takes the place of the shared DPLLs we've used on past platforms. Let's add the MPLLB programming sequences; they'll be plugged into the rest of the code in future patches. Bspec: 54032 Bspec: 53881 Cc: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Nidhi Gupta <nidhi1.gupta@intel.com> Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-24-matthew.d.roper@intel.com
2021-05-05drm/i915: Don't include intel_de.h from intel_display_types.hVille Syrjälä
Hoist the intel_de.h include from intel_display_types.h one level up. I need this in order to untangle the include order so that I can add tracepoints into intel_de.h. This little cocci script did most of the work for me: @find@ @@ ( intel_de_read(...) | intel_de_read_fw(...) | intel_de_write(...) | intel_de_write_fw(...) ) @has_include@ @@ ( #include "intel_de.h" | #include "display/intel_de.h" ) @depends on find && !has_include@ @@ + #include "intel_de.h" #include "intel_display_types.h" @depends on find && !has_include@ @@ + #include "display/intel_de.h" #include "display/intel_display_types.h" Cc: Cooper Chiou <cooper.chiou@intel.com> Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com
2021-04-14drm/i915/display: rename display version macrosLucas De Marchi
While converting the rest of the driver to use GRAPHICS_VER() and MEDIA_VER(), following what was done for display, some discussions went back on what we did for display: 1) Why is the == comparison special that deserves a separate macro instead of just getting the version and comparing directly like is done for >, >=, <=? 2) IS_DISPLAY_RANGE() is weird in that it omits the "_VER" for brevity. If we remove the current users of IS_DISPLAY_VER(), we could actually repurpose it for a range check With (1) there could be an advantage if we used gen_mask since multiple conditionals be combined by the compiler in a single and instruction and check the result. However a) INTEL_GEN() doesn't use the mask since it would make the code bigger everywhere else and b) in the cases it made sense, it also made sense to convert to the _RANGE() variant. So here we repurpose IS_DISPLAY_VER() to work with a [ from, to ] range like was the IS_DISPLAY_RANGE() and convert the current IS_DISPLAY_VER() users to use == and != operators. Aside from the definition changes, this was done by the following semantic patch: @@ expression dev_priv, E1; @@ - !IS_DISPLAY_VER(dev_priv, E1) + DISPLAY_VER(dev_priv) != E1 @@ expression dev_priv, E1; @@ - IS_DISPLAY_VER(dev_priv, E1) + DISPLAY_VER(dev_priv) == E1 @@ expression dev_priv, from, until; @@ - IS_DISPLAY_RANGE(dev_priv, from, until) + IS_DISPLAY_VER(dev_priv, from, until) Cc: Jani Nikula <jani.nikula@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> [Jani: Minor conflict resolve while applying.] Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20210413051002.92589-4-lucas.demarchi@intel.com
2021-04-14drm/i915/display: Eliminate IS_GEN9_{BC,LP}Matt Roper
Now that we've eliminated INTEL_GEN(), IS_GEN_RANGE(), etc. from the display code, we should also kill off our use of the IS_GEN9_* macros too. We'll do the conversion manually this time instead of using Coccinelle since the most logical substitution can depend heavily on the code context, and sometimes we can keep the code simpler if we make additional adjustments such as swapping the order of if/else arms. v2: - Restore a lost negation in intel_pll_is_valid(). Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210407203945.1432531-1-matthew.d.roper@intel.com (cherry picked from commit 70bfb30743d5da73058b0a2271e9c127a84fb494) [Jani: cherry picked to topic branch to reduce conflicts] Signed-off-by: Jani Nikula <jani.nikula@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-29 15:13:01 +0000