summaryrefslogtreecommitdiff
path: root/drivers/gpu/drm/display/drm_dp_helper.c
AgeCommit message (Collapse)Author
2025-07-15drm/dp: Change AUX DPCD probe address from LANE0_1_STATUS to ↵Imre Deak
TRAINING_PATTERN_SET Commit a3ef3c2da675 ("drm/dp: Change AUX DPCD probe address from DPCD_REV to LANE0_1_STATUS") stopped using the DPCD_REV register for DPCD probing, since this results in link training failures at least when using an Intel Barlow Ridge TBT hub at UHBR link rates (the DP_INTRA_HOP_AUX_REPLY_INDICATION never getting cleared after the failed link training). Since accessing DPCD_REV during link training is prohibited by the DP Standard, LANE0_1_STATUS (0x202) was used instead, as it falls within the Standard's valid register address range (0x102-0x106, 0x202-0x207, 0x200c-0x200f, 0x2216) and it fixed the link training on the above TBT hub. However, reading the LANE0_1_STATUS register also has a side-effect at least on a Novatek eDP panel, as reported on the Closes: link below, resulting in screen flickering on that panel. One clear side-effect when doing the 1-byte probe reads from LANE0_1_STATUS during link training before reading out the full 6 byte link status starting at the same address is that the panel will report the link training as completed with voltage swing 0. This is different from the normal, flicker-free scenario when no DPCD probing is done, the panel reporting the link training complete with voltage swing 2. Using the TRAINING_PATTERN_SET register for DPCD probing doesn't have the above side-effect, the panel will link train with voltage swing 2 as expected and it will stay flicker-free. This register is also in the above valid register range and is unlikely to have a side-effect as that of LANE0_1_STATUS: Reading LANE0_1_STATUS is part of the link training CR/EQ sequences and so it may cause a state change in the sink - even if inadvertently as I suspect in the case of the above Novatek panel. As opposed to this, reading TRAINING_PATTERN_SET is not part of the link training sequence (it must be only written once at the beginning of the CR/EQ sequences), so it's unlikely to cause any state change in the sink. As a side-note, this Novatek panel also lacks support for TPS3, while claiming support for HBR2, which violates the DP Standard (the Standard mandating TPS3 for HBR2). Besides the Novatek panel (PSR 1), which this change fixes, I also verified the change on a Samsung (PSR 1) and an Analogix (PSR 2) eDP panel as well as on the Intel Barlow Ridge TBT hub. Note that in the drm-tip tree (targeting the v6.17 kernel version) the i915 and xe drivers keep DPCD probing enabled only for the panel known to require this (HP ZR24w), hence those drivers in drm-tip are not affected by the above problem. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Fixes: a3ef3c2da675 ("drm/dp: Change AUX DPCD probe address from DPCD_REV to LANE0_1_STATUS") Reported-and-tested-by: Paul Menzel <pmenzel@molgen.mpg.de> Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14558 Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://lore.kernel.org/r/20250708212331.112898-1-imre.deak@intel.com (cherry picked from commit bba9aa41654036534d86b198f5647a9ce15ebd7f) [Imre: Rebased on drm-intel-fixes] Signed-off-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> [Rodrigo: Changed original commit hash to match with the one propagated in fixes]
2025-06-23drm/dp: Change AUX DPCD probe address from DPCD_REV to LANE0_1_STATUSImre Deak
Reading DPCD registers has side-effects in general. In particular accessing registers outside of the link training register range (0x102-0x106, 0x202-0x207, 0x200c-0x200f, 0x2216) is explicitly forbidden by the DP v2.1 Standard, see 3.6.5.1 DPTX AUX Transaction Handling Mandates 3.6.7.4 128b/132b DP Link Layer LTTPR Link Training Mandates Based on my tests, accessing the DPCD_REV register during the link training of an UHBR TBT DP tunnel sink leads to link training failures. Solve the above by using the DP_LANE0_1_STATUS (0x202) register for the DPCD register access quirk. Cc: <stable@vger.kernel.org> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Acked-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://lore.kernel.org/r/20250605082850.65136-2-imre.deak@intel.com (cherry picked from commit a40c5d727b8111b5db424a1e43e14a1dcce1e77f) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
2025-05-19drm/dp: add option to disable zero sized address only transactions.Dave Airlie
Some older NVIDIA and some newer NVIDIA hardware/firmware seems to have issues with address only transactions (firmware rejects them). Add an option to the core drm dp to avoid address only transactions, This just puts the MOT flag removal on the last message of the transfer and avoids the start of transfer transaction. This with the flag set in nouveau, allows eDP probing on GB203 device. Signed-off-by: Dave Airlie <airlied@redhat.com> Reviewed-by: Ben Skeggs <bskeggs@nvidia.com> Reviewed-by: Timur Tabi <ttabi@nvidia.com> Tested-by: Timur Tabi <ttabi@nvidia.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2025-05-10Merge tag 'drm-intel-next-2025-05-08' of ↵Dave Airlie
https://gitlab.freedesktop.org/drm/i915/kernel into drm-next Non-display related: - Fix undefined reference to `intel_pxp_gsccs_is_ready_for_sessions' Display related: - More work towards display separation (Jani) - Stop writing VRR_CTL_IGN_MAX_SHIFT for MTL onwards (Jouni) - DSC checks for 3 engines (Ankit) - Add link rate and lane count to i915_display_info (Khaled) - PSR fixes and workaround for underrun on idle (Jouni) - LOBF enablement and ALMP fixes (Animesh) - Clean up VGA plane handling (Ville) - Use an intel_connector pointer everywhere (Imre) - Fix warning for coffeelake on SunrisePoint PCH (Jiajia) - Rework/Correction on minimum hblank calculation (Arun) - Dmesg clean up (Jani) - Add a couple of simple display workarounds (Ankit, Vinod) - Refactor HDCP GSC (Jani) Signed-off-by: Dave Airlie <airlied@redhat.com> From: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://lore.kernel.org/r/aByyL3bEufPu79OM@intel.com
2025-04-30drm/display/dp: Export fn to calculate link symbol cyclesArun R Murthy
Unify the function to calculate the link symbol cycles for both dsc and non-dsc case and export the function so that it can be used in the respective platform display drivers for other calculations. v2: unify the fn for both dsc and non-dsc case (Imre) v3: rename drm_dp_link_symbol_cycles to drm_dp_link_data_symbol_cycles retain slice_eoc_cycles as is (Imre) v4: Expose only drm_dp_link_symbol_cycles() (Imre) v6: Add slice pixels which was removed unknowingly (Vinod) Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com> Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://lore.kernel.org/r/20250424-hblank-v7-1-8b002f1506cc@intel.com
2025-04-02drm/dp: Pull drm_dp_link_power_up/down from Tegra to common drm_dp_helperAndy Yan
The helper functions drm_dp_link_power_up/down were moved to Tegra DRM in commit 9a42c7c647a9 ("drm/tegra: Move drm_dp_link helpers to Tegra DRM")". Now since more and more users are duplicating the same code in their own drivers, it's time to make them as DRM DP common helpers again. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Acked-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250318063452.4983-1-andyshrk@163.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
2025-03-25drm/display: dp: use new DCPD access helpersDmitry Baryshkov
Switch drm_dp_helper.c to use new set of DPCD read / write helpers. Reviewed-by: Lyude Paul <lyude@redhat.com> Acked-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20250324-drm-rework-dpcd-access-v4-3-e80ff89593df@oss.qualcomm.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
2025-03-25drm/display: dp: change drm_dp_dpcd_read_link_status() return valueDmitry Baryshkov
drm_dp_dpcd_read_link_status() follows the "return error code or number of bytes read" protocol, with the code returning less bytes than requested in case of some errors. However most of the drivers interpreted that as "return error code in case of any error". Switch drm_dp_dpcd_read_link_status() to drm_dp_dpcd_read_data() and make it follow that protocol too. Acked-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20250324-drm-rework-dpcd-access-v4-2-e80ff89593df@oss.qualcomm.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
2025-03-25drm/display: dp: implement new access helpersDmitry Baryshkov
Existing DPCD access functions return an error code or the number of bytes being read / write in case of partial access. However a lot of drivers either (incorrectly) ignore partial access or mishandle error codes. In other cases this results in a boilerplate code which compares returned value with the size. Implement new set of DPCD access helpers, which ignore partial access, always return 0 or an error code. Suggested-by: Jani Nikula <jani.nikula@linux.intel.com> Acked-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20250324-drm-rework-dpcd-access-v4-1-e80ff89593df@oss.qualcomm.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
2025-02-25drm/dp: Add helper to set LTTPRs in transparent modeAbel Vesa
According to the DisplayPort standard, LTTPRs have two operating modes: - non-transparent - it replies to DPCD LTTPR field specific AUX requests, while passes through all other AUX requests - transparent - it passes through all AUX requests. Switching between this two modes is done by the DPTX by issuing an AUX write to the DPCD PHY_REPEATER_MODE register. Add a generic helper that allows switching between these modes. Also add a generic wrapper for the helper that handles the explicit disabling of non-transparent mode and its disable->enable sequence mentioned in the DP Standard v2.0 section 3.6.6.1. Do this in order to move this handling out of the vendor specific driver implementation into the generic framework. Tested-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Acked-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20250203-drm-dp-msm-add-lttpr-transparent-mode-set-v5-1-c865d0e56d6e@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2025-02-25Merge tag 'v6.14-rc4' into drm-nextDave Airlie
Backmerge Linux 6.14-rc4 at the request of tzimmermann so misc-next can base on rc4. Signed-off-by: Dave Airlie <airlied@redhat.com>
2025-02-13drm: Fix DSC BPP increment decodingImre Deak
Starting with DPCD version 2.0 bits 6:3 of the DP_DSC_BITS_PER_PIXEL_INC DPCD register contains the NativeYCbCr422_MAX_bpp_DELTA field, which can be non-zero as opposed to earlier DPCD versions, hence decoding the bit_per_pixel increment value at bits 2:0 in the same register requires applying a mask, do so. Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Fixes: 0c2287c96521 ("drm/display/dp: Add helper function to get DSC bpp precision") Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20250212161851.4007005-1-imre.deak@intel.com
2025-02-04drm/display/dp: Define function to setup Extended wake timeSuraj Kandpal
Extended wake timeout request helps to give additional time by reading the DPCD register through which sink requests the minimal amount of time required to wake the sink up. Source device shall keep retying the AUX tansaction till the extended timeout that is being granted for LTTPRs from the sink device. --v2 -Add documentation [Dmitry] Spec: DP v2.1 Section 3.6.12.3 Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20250122053358.1545039-3-suraj.kandpal@intel.com
2024-12-03drm/dp: extract drm_dp_dpcd_clear_payload()Jani Nikula
SST with 128b/132b channel coding needs this too. Extract to a separate helper, independent of MST. Cc: Lyude Paul <lyude@redhat.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/904fa73ea9ea976185062eeb493a08ffc43ed27e.1733238941.git.jani.nikula@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2024-12-03drm/dp: extract drm_dp_dpcd_write_payload()Jani Nikula
SST with 128b/132b channel coding needs this too. Extract to a separate helper, independent of MST. v2: Clean up kernel-doc a bit Cc: Lyude Paul <lyude@redhat.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/f626715ba4e348546770750aa3e10fac73a5cbd7.1733238941.git.jani.nikula@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2024-12-03drm/dp: extract drm_dp_dpcd_poll_act_handled()Jani Nikula
SST with 128b/132b channel coding needs this too. Extract to a separate helper, independent of MST. Pass timeout in as a parameter, anticipating that we can reduce the timeout for SST. v2: Clean up kernel-doc a bit Cc: Lyude Paul <lyude@redhat.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/459fd3e96a55a8ea8ada8d27d93eaa24c235f9c1.1733238941.git.jani.nikula@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2024-07-11drm/dp: Add helper to dump an LTTPR PHY descriptorImre Deak
Add a helper to dump the DPCD descriptor for an LTTPR PHY. This is based on [1] and [2] moving the helper to DRM core as suggested by Ville. [1] https://lore.kernel.org/all/20240703155937.1674856-5-imre.deak@intel.com [2] https://lore.kernel.org/all/20240703155937.1674856-6-imre.deak@intel.com Cc: dri-devel@lists.freedesktop.org Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240708190029.271247-6-imre.deak@intel.com
2024-07-03drm: Add helpers for q4 fixed point valuesImre Deak
Add helpers to convert between q4 fixed point and integer/fraction values. Also add the format/argument macros required to printk q4 fixed point variables. The q4 notation is based on the short variant described by https://en.wikipedia.org/wiki/Q_(number_format) where only the number of fraction bits in the fixed point value are defined, while the full size is deducted from the container type, that is the size of int for these helpers. Using the fxp_ prefix, which makes moving these helpers outside of drm to a more generic place easier, if they prove to be useful. These are needed by later patches dumping the Display Stream Compression configuration in DRM core and in the i915 driver to replace the corresponding bpp_x16 helpers defined locally in the driver. v2: Use the more generic/descriptive fxp_q4 prefix instead of drm_x16. (Jani) Cc: Jani Nikula <jani.nikula@intel.com> Acked-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240628164451.1177612-2-imre.deak@intel.com
2024-04-26Merge tag 'drm-intel-next-2024-04-24' of ↵Dave Airlie
https://anongit.freedesktop.org/git/drm/drm-intel into drm-next Core Changes: - Some DP/DP_MST DRM helpers (Imre) Driver Changes (i915 Display): - PLL refactoring (Ville) - Limit eDP MSO pipe only for display version 20 (Luca) - More display refactor towards independence from i915 dev_priv (Jani) - QGV/SAGV related refactor (Stanislav) - Few MTL/DSC and a UHBR monitor fix (Imre) - BXT/GLK per-lane vswing and PHY reg cleanup (Ville) Signed-off-by: Dave Airlie <airlied@redhat.com> From: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/Zik0LKEtN1PwXXGb@intel.com
2024-04-19drm/i915/dp_mst: Enable HBLANK expansion quirk for UHBR ratesImre Deak
Enabling the 5k@60Hz uncompressed mode on the MediaTek/Dell U3224KBA monitor results in a blank screen, at least on MTL platforms on UHBR link rates with some (<30) uncompressed bpp values. Enabling compression fixes the problem, so do that for now. Windows enables DSC always if the sink supports it and forcing it to enable the mode without compression leads to the same problem above (which suggests a panel issue with uncompressed mode). The same 5k mode on non-UHBR link rates is not affected and lower resolution modes are not affected either. The problem is similar to the one fixed by the HBLANK expansion quirk on Synaptics hubs, with the difference that the problematic mode has a longer HBLANK duration. Also the monitor doesn't report supporting HBLANK expansion; either its internal MST hub does the expansion internally - similarly to the Synaptics hub - or the issue has another root cause, but still related to the mode's short HBLANK duration. Enable the quirk for the monitor adjusting the detection for the above differences. v2: Rebase on drm_dp_128132b_supported() change. Cc: dri-devel@lists.freedesktop.org Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com> Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240417142217.457902-1-imre.deak@intel.com
2024-04-19Merge tag 'drm-intel-next-2024-04-17-1' of ↵Dave Airlie
https://anongit.freedesktop.org/git/drm/drm-intel into drm-next Core Changes (DRM): - Fix documentation of DP tunnel functions (Imre) - DP MST read sideband messaging cap (Jani) - Preparation patches for Adaptive Sync SDP Support for DP (Mitul) Driver Changes: i915 core (non-display): - Documentation improvements (Nirmoy) - Add includes for BUG_ON/BUILD_BUG_ON in i915_memcpy.c (Joonas) - Do not print 'pxp init failed with 0' when it succeed (Jose) - Clean-up, including removal of dead code for unsupported platforms (Lucas) - Adding new DG2 PCI ID (Ravi) {i915,xe} display: - Spelling fix (Colin Ian) - Document CDCLK components (Gustavo) - Lunar Lake display enabling, including cdclk and other refactors (Gustavo, Bala) - BIOS/VBT/opregion related refactor (Jani, Ville, RK) - Save a few bytes of memory using {kstrdup,kfree}_const variant (Christophe) - Digital port related refactor/clean-up (Ville) - Fix 2s boot time regression on DP panel replay init (Animesh) - Remove redundant drm_rect_visible() overlay use (Arthur) - DSC HW state readout fixes (Imre) - Remove duplication on audio enable/disable on SDVO and g4x+ DP (Ville) - Disable AuxCCS framebuffers if built for Xe (Juha-Pekka) - Fix DSI init order (Ville) - DRRS related refactor and fixes (Bhanuprakash) - Fix DSB vblank waits with VRR (Ville) - General improvements on register name and use of REG_BIT (Ville) - Some display power well related improvements (Ville) - FBC changes for better w/a handling (Ville) - Make crtc disable more atomic (Ville) - Fix hwmon locking inversion in sysfs getter (Janusz) - Increase DP idle pattern wait timeout to 2ms (Shekhar) - PSR related fixes and improvents (Jouni) - Start using container_of_const() for some extra const safety (Ville) - Use drm_printer more on display code (Ville) - Fix Jasper Lake boot freeze (Jonathon) - Update Pipe src size check in skl_update_scaler (Ankit) - Enable MST mode for 128b/132b single-stream sideband (Jani) - Pass encoder around more for port/phy checks (Jani) - Some initial work to make display code more independent from i915 (Jani) - Pre-populate the cursor physical dma address (Ville) - Do not bump min backlight brightness to max on enable (Gareth) - Fix MTL supported DP rates - removal of UHBR13.5 (Arun) - Fix the computation for compressed_bpp for DISPLAY < 1 (Ankit) - Bigjoiner modeset sequence redesign and MST support (Ville) - Enable Adaptive Sync SDP Support for DP (Mitul) - Implemnt vblank sycnhronized mbus joining changes (Ville, Stanislav) - HDCP related fixes (Suraj) - Fix i915_display_info debugfs when connectors are not active (Ville) - Clean up on Xe compat layer (Jani) - Add jitter WAs for MST/FEC/DSC links (Imre) - DMC wakelock implementation (Luca) Signed-off-by: Dave Airlie <airlied@redhat.com> # -----BEGIN PGP SIGNATURE----- # # iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmYfzQEACgkQ+mJfZA7r # E8qYvAf/T8KrEewHOWz7NOaKcFRCNYaF4QTdVOfgHUYBX5NPDF/xzwFdHCL8QWQu # bwKwE2b94VEyruG3DYwTMd8GNcDxrsOrmU0IZe3PVkm+BvHLTmrOqL6BlCd85zXF # 02IuE+LCaWREmmpLMcsDMxsaaq8yp+cw9/F0jJDrH6LiyfxFriefxyZYpGYjRCuv # 8GP1fHXLFV2yys4rveR/+y9xIhgy82mVcg3/Kfk0+er7gALkY6Vc0N38wedET9MZ # ZPfVidBeaTkIKcCDFKnFzGjG+9rNQ7NFrXyS7Hl97VolGt2l03qGGPNW1PouDiUx # 7Y8CJOc+1k9wyBMKl0a/NQBRAqSZBQ== # =JvZN # -----END PGP SIGNATURE----- # gpg: Signature made Wed 17 Apr 2024 23:22:09 AEST # gpg: using RSA key 6D207068EEDD65091C2CE2A3FA625F640EEB13CA # gpg: Good signature from "Rodrigo Vivi <rodrigo.vivi@intel.com>" [unknown] # gpg: aka "Rodrigo Vivi <rodrigo.vivi@gmail.com>" [unknown] # gpg: WARNING: This key is not certified with a trusted signature! # gpg: There is no indication that the signature belongs to the owner. # Primary key fingerprint: 6D20 7068 EEDD 6509 1C2C E2A3 FA62 5F64 0EEB 13CA From: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/Zh_Q72gYKMMbge9A@intel.com
2024-04-05Merge tag 'drm-misc-next-2024-03-28' of ↵Dave Airlie
https://gitlab.freedesktop.org/drm/misc/kernel into drm-next Two misc-next in one. drm-misc-next for v6.10-rc1: The deal of a lifetime! You get ALL of the previous drm-misc-next-2024-03-21-1 tag!! But WAIT, there's MORE! Cross-subsystem Changes: - Assorted DT binding updates. Core Changes: - Clarify how optional wait_hpd_asserted is. - Shuffle Kconfig names around. Driver Changes: - Assorted build fixes for panthor, imagination, - Add AUO B120XAN01.0 panels. - Assorted small fixes to panthor, panfrost. drm-misc-next for v6.10: UAPI Changes: - Move some nouveau magic constants to uapi. Cross-subsystem Changes: - Move drm-misc to gitlab and freedesktop hosting. - Add entries for panfrost. Core Changes: - Improve placement for TTM bo's in idle/busy handling. - Improve drm/bridge init ordering. - Add CONFIG_DRM_WERROR, and use W=1 for drm. - Assorted documentation updates. - Make more (drm and driver) headers self-contained and add header guards. - Grab reservation lock in pin/unpin callbacks. - Fix reservation lock handling for vmap. - Add edp and edid panel matching, use it to fix a nearly identical panel. Driver Changes: - Add drm/panthor driver and assorted fixes. - Assorted small fixes to xlnx, panel-edp, tidss, ci, nouveau, panel and bridge drivers. - Add Samsung s6e3fa7, BOE NT116WHM-N44, CMN N116BCA-EA1, CrystalClear CMT430B19N00, Startek KD050HDFIA020-C020A, powertip PH128800T006-ZHC01 panels. - Fix console for omapdrm. Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/bea310a6-6ff6-477e-9363-f9f053cfd12a@linux.intel.com
2024-04-04drm/dp: Add Adaptive Sync SDP loggingMitul Golani
Add structure representing Adaptive Sync Secondary Data Packet (AS SDP). Also, add Adaptive Sync SDP logging in drm_dp_helper.c to facilitate debugging. --v2: - Update logging. [Jani, Ankit] - Use 'as_sdp' instead of 'async' [Ankit] - Correct define placeholders to where they are actually used. [Jani] - Update members in 'as_sdp' structure to make it uniform. [Jani] --v3: - Added changes to dri-devel mailing list. No code changes. --v4: - Instead of directly using operation mode, use an enum to accommodate all operation modes (Ankit). --v5: Nit-pick changes to commit message. --v6: - Add correct place holder and name change for AS_SDP_OP_MODE. - Separate i915 changes from drm changes. - Remove extra lines. --v7: - Add drm/dp in subject line (Ankit) Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com> Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-3-mitulkumar.ajitkumar.golani@intel.com
2024-04-04drm/dp: Add support to indicate if sink supports AS SDPMitul Golani
Add an API that indicates support for Adaptive Sync SDP in the sink, which can be utilized by the rest of the DP programming. --v1: - Format commit message properly. Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com> Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-2-mitulkumar.ajitkumar.golani@intel.com
2024-03-28drm/display: Make DisplayPort AUX Chardev Kconfig name consistentMaxime Ripard
While most display helpers Kconfig symbols have the DRM_DISPLAY prefix, the DisplayPort-AUX chardev interface uses DRM_DP_AUX_CHARDEV. Since the number of users is limited and it's a selected symbol, we can easily rename it to make it consistent. Reviewed-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-3-eafee11b84b3@kernel.org Signed-off-by: Maxime Ripard <mripard@kernel.org>
2024-03-25Merge drm/drm-fixes into drm-misc-fixesThomas Zimmermann
Backmerging to get drm-misc-fixes to the state of v6.9-rc1. Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
2024-03-18drm/dp: Fix divide-by-zero regression on DP MST unplug with nouveauChris Bainbridge
Fix a regression when using nouveau and unplugging a StarTech MSTDP122DP DisplayPort 1.2 MST hub (the same regression does not appear when using a Cable Matters DisplayPort 1.4 MST hub). Trace: divide error: 0000 [#1] PREEMPT SMP PTI CPU: 7 PID: 2962 Comm: Xorg Not tainted 6.8.0-rc3+ #744 Hardware name: Razer Blade/DANA_MB, BIOS 01.01 08/31/2018 RIP: 0010:drm_dp_bw_overhead+0xb4/0x110 [drm_display_helper] Code: c6 b8 01 00 00 00 75 61 01 c6 41 0f af f3 41 0f af f1 c1 e1 04 48 63 c7 31 d2 89 ff 48 8b 5d f8 c9 48 0f af f1 48 8d 44 06 ff <48> f7 f7 31 d2 31 c9 31 f6 31 ff 45 31 c0 45 31 c9 45 31 d2 45 31 RSP: 0018:ffffb2c5c211fa30 EFLAGS: 00010206 RAX: ffffffffffffffff RBX: 0000000000000000 RCX: 0000000000f59b00 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffffb2c5c211fa48 R08: 0000000000000001 R09: 0000000000000020 R10: 0000000000000004 R11: 0000000000000000 R12: 0000000000023b4a R13: ffff91d37d165800 R14: ffff91d36fac6d80 R15: ffff91d34a764010 FS: 00007f4a1ca3fa80(0000) GS:ffff91d6edbc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000559491d49000 CR3: 000000011d180002 CR4: 00000000003706f0 Call Trace: <TASK> ? show_regs+0x6d/0x80 ? die+0x37/0xa0 ? do_trap+0xd4/0xf0 ? do_error_trap+0x71/0xb0 ? drm_dp_bw_overhead+0xb4/0x110 [drm_display_helper] ? exc_divide_error+0x3a/0x70 ? drm_dp_bw_overhead+0xb4/0x110 [drm_display_helper] ? asm_exc_divide_error+0x1b/0x20 ? drm_dp_bw_overhead+0xb4/0x110 [drm_display_helper] ? drm_dp_calc_pbn_mode+0x2e/0x70 [drm_display_helper] nv50_msto_atomic_check+0xda/0x120 [nouveau] drm_atomic_helper_check_modeset+0xa87/0xdf0 [drm_kms_helper] drm_atomic_helper_check+0x19/0xa0 [drm_kms_helper] nv50_disp_atomic_check+0x13f/0x2f0 [nouveau] drm_atomic_check_only+0x668/0xb20 [drm] ? drm_connector_list_iter_next+0x86/0xc0 [drm] drm_atomic_commit+0x58/0xd0 [drm] ? __pfx___drm_printfn_info+0x10/0x10 [drm] drm_atomic_connector_commit_dpms+0xd7/0x100 [drm] drm_mode_obj_set_property_ioctl+0x1c5/0x450 [drm] ? __pfx_drm_connector_property_set_ioctl+0x10/0x10 [drm] drm_connector_property_set_ioctl+0x3b/0x60 [drm] drm_ioctl_kernel+0xb9/0x120 [drm] drm_ioctl+0x2d0/0x550 [drm] ? __pfx_drm_connector_property_set_ioctl+0x10/0x10 [drm] nouveau_drm_ioctl+0x61/0xc0 [nouveau] __x64_sys_ioctl+0xa0/0xf0 do_syscall_64+0x76/0x140 ? do_syscall_64+0x85/0x140 ? do_syscall_64+0x85/0x140 entry_SYSCALL_64_after_hwframe+0x6e/0x76 RIP: 0033:0x7f4a1cd1a94f Code: 00 48 89 44 24 18 31 c0 48 8d 44 24 60 c7 04 24 10 00 00 00 48 89 44 24 08 48 8d 44 24 20 48 89 44 24 10 b8 10 00 00 00 0f 05 <41> 89 c0 3d 00 f0 ff ff 77 1f 48 8b 44 24 18 64 48 2b 04 25 28 00 RSP: 002b:00007ffd2f1df520 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007ffd2f1df5b0 RCX: 00007f4a1cd1a94f RDX: 00007ffd2f1df5b0 RSI: 00000000c01064ab RDI: 000000000000000f RBP: 00000000c01064ab R08: 000056347932deb8 R09: 000056347a7d99c0 R10: 0000000000000000 R11: 0000000000000246 R12: 000056347938a220 R13: 000000000000000f R14: 0000563479d9f3f0 R15: 0000000000000000 </TASK> Modules linked in: rfcomm xt_conntrack nft_chain_nat xt_MASQUERADE nf_nat nf_conntrack_netlink nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 xfrm_user xfrm_algo xt_addrtype nft_compat nf_tables nfnetlink br_netfilter bridge stp llc ccm cmac algif_hash overlay algif_skcipher af_alg bnep binfmt_misc snd_sof_pci_intel_cnl snd_sof_intel_hda_common snd_soc_hdac_hda snd_sof_pci snd_sof_xtensa_dsp snd_sof_intel_hda snd_sof snd_sof_utils snd_soc_acpi_intel_match snd_soc_acpi snd_soc_core snd_compress snd_sof_intel_hda_mlink snd_hda_ext_core iwlmvm intel_rapl_msr intel_rapl_common intel_tcc_cooling x86_pkg_temp_thermal intel_powerclamp mac80211 coretemp kvm_intel snd_hda_codec_hdmi kvm snd_hda_codec_realtek snd_hda_codec_generic uvcvideo libarc4 snd_hda_intel snd_intel_dspcfg snd_hda_codec iwlwifi videobuf2_vmalloc videobuf2_memops uvc irqbypass btusb videobuf2_v4l2 snd_seq_midi crct10dif_pclmul hid_multitouch crc32_pclmul snd_seq_midi_event btrtl snd_hwdep videodev polyval_clmulni polyval_generic snd_rawmidi ghash_clmulni_intel aesni_intel btintel crypto_simd snd_hda_core cryptd snd_seq btbcm ee1004 8250_dw videobuf2_common btmtk rapl nls_iso8859_1 mei_hdcp thunderbolt bluetooth intel_cstate wmi_bmof intel_wmi_thunderbolt cfg80211 snd_pcm mc snd_seq_device i2c_i801 r8169 ecdh_generic snd_timer i2c_smbus ecc snd mei_me intel_lpss_pci mei ahci intel_lpss soundcore realtek libahci idma64 intel_pch_thermal i2c_hid_acpi i2c_hid acpi_pad sch_fq_codel msr parport_pc ppdev lp parport efi_pstore ip_tables x_tables autofs4 dm_crypt raid10 raid456 libcrc32c async_raid6_recov async_memcpy async_pq async_xor xor async_tx raid6_pq raid1 raid0 joydev input_leds hid_generic usbhid hid nouveau i915 drm_ttm_helper gpu_sched drm_gpuvm drm_exec i2c_algo_bit drm_buddy ttm drm_display_helper drm_kms_helper cec rc_core drm nvme nvme_core mxm_wmi xhci_pci xhci_pci_renesas video wmi pinctrl_cannonlake mac_hid ---[ end trace 0000000000000000 ]--- Fix this by avoiding the divide if bpp is 0. Fixes: c1d6a22b7219 ("drm/dp: Add helpers to calculate the link BW overhead") Cc: stable@vger.kernel.org Acked-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/ZfWLJwYikw2K7B6c@debian.local
2024-03-01Merge tag 'drm-misc-next-2024-02-29' of ↵Dave Airlie
https://anongit.freedesktop.org/git/drm/drm-misc into drm-next drm-misc-next for v6.9: UAPI Changes: Cross-subsystem Changes: backlight: - corgi: include backlight header fbdev: - Cleanup includes in public header file - fbtft: Include backlight header Core Changes: edid: - Remove built-in EDID data dp: - Avoid AUX transfers on powered-down displays - Add VSC SDP helpers modesetting: - Add sanity checks for polling - Cleanups scheduler: - Cleanups tests: - Add helpers for mode-setting tests Driver Changes: i915: - Use shared VSC SDP helper mgag200: - Work around PCI write bursts mxsfb: - Use managed mode config nouveau: - Include backlight header where necessary qiac: - Cleanups sun4: - HDMI: updates to atomic mode setting tegra: - Fix GEM refounting in error paths tidss: - Fix multi display - Fix initial Z position v3d: - Support display MMU page size Signed-off-by: Dave Airlie <airlied@redhat.com> From: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20240229084806.GA21616@localhost.localdomain
2024-02-28drm/dp: Don't attempt AUX transfers when eDP panels are not poweredDouglas Anderson
If an eDP panel is not powered on then any attempts to talk to it over the DP AUX channel will timeout. Unfortunately these attempts may be quite slow. Userspace can initiate these attempts either via a /dev/drm_dp_auxN device or via the created i2c device. Making the DP AUX drivers timeout faster is a difficult proposition. In theory we could just poll the panel's HPD line in the AUX transfer function and immediately return an error there. However, this is easier said than done. For one thing, there's no hard requirement to hook the HPD line up for eDP panels and it's OK to just delay a fixed amount. For another thing, the HPD line may not be fast to probe. On parade-ps8640 we need to wait for the bridge chip's firmware to boot before we can get the HPD line and this is a slow process. The fact that the transfers are taking so long to timeout is causing real problems. The open source fwupd daemon sometimes scans DP busses looking for devices whose firmware need updating. If it happens to scan while a panel is turned off this scan can take a long time. The fwupd daemon could try to be smarter and only scan when eDP panels are turned on, but we can also improve the behavior in the kernel. Let's let eDP panels drivers specify that a panel is turned off and then modify the common AUX transfer code not to attempt a transfer in this case. Tested-by: Steev Klimaszewski <steev@kali.org> Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org> Tested-by: Eizan Miyamoto <eizan@chromium.org> Acked-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240202141109.1.I24277520ac754ea538c9b14578edc94e1df11b48@changeid
2024-02-28Merge tag 'drm-intel-next-2024-02-27-1' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-intel into drm-next drm/i915 feature pull #2 for v6.9: Features and functionality: - DP tunneling and bandwidth allocation support (Imre) - Add more ADL-N PCI IDs (Gustavo) - Enable fastboot also on older platforms (Ville) - Bigjoiner force enable debugfs option for testing (Stan) Refactoring and cleanups: - Remove unused structs and struct members (Jiri Slaby) - Use per-device debug logging (Ville) - State check improvements (Ville) - Hardcoded cd2x divider cleanups (Ville) - CDCLK documentation updates (Ville, Rodrigo) Fixes: - HDCP MST Type1 fixes (Suraj) - Fix MTL C20 PHY PLL values (Ravi) - More hardware access prevention during init (Imre) - Always enable decompression with tile4 on Xe2 (Juha-Pekka) - Improve LNL package C residency (Suraj) drm core changes: - DP tunneling and bandwidth allocation helpers (Imre) Signed-off-by: Dave Airlie <airlied@redhat.com> From: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/87sf1devbj.fsf@intel.com
2024-02-27drm/dp: Add drm_dp_max_dprx_data_rate()Imre Deak
Copy intel_dp_max_data_rate() to DRM core. It will be needed by a follow-up DP tunnel patch, checking the maximum rate the DPRX (sink) supports. Accordingly use the drm_dp_max_dprx_data_rate() name for clarity. This patchset will also switch calling the new DRM function in i915 instead of intel_dp_max_data_rate(). While at it simplify the function documentation/comments, removing parts described already by drm_dp_bw_channel_coding_efficiency(). v2: (Ville) - Remove max_link_rate_kbps. - Simplify the function documentation. v3: - Rebased on latest drm-tip. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240226185246.1276018-1-imre.deak@intel.com
2024-02-22drm/dp: add an API to indicate if sink supports VSC SDPPaloma Arellano
YUV420 format is supported only in the VSC SDP packet and not through MSA. Hence add an API which indicates the sink support which can be used by the rest of the DP programming. changes in v5: - rebased on top of drm-tip changes in v4: - bail out early if dpcd rev check fails changes in v3: - fix the commit title prefix to drm/dp - get rid of redundant !! - break out this change from series [1] to get acks from drm core maintainers Changes in v2: - Move VSC SDP support check API from dp_panel.c to drm_dp_helper.c [1]: https://patchwork.freedesktop.org/series/129180/ Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Paloma Arellano <quic_parellan@quicinc.com> Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240215191556.3227259-1-quic_abhinavk@quicinc.com
2024-02-22drm/dp: drop the size parameter from drm_dp_vsc_sdp_pack()Abhinav Kumar
Currently the size parameter of drm_dp_vsc_sdp_pack() is always the size of struct dp_sdp. Hence lets drop this parameter and use sizeof() directly. Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240220195348.1270854-2-quic_abhinavk@quicinc.com
2024-02-22drm/dp: move intel_dp_vsc_sdp_pack() to generic helperAbhinav Kumar
intel_dp_vsc_sdp_pack() can be re-used by other DRM drivers as well. Lets move this to drm_dp_helper to achieve this. changes in v2: - rebased on top of drm-tip Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Acked-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240220195348.1270854-1-quic_abhinavk@quicinc.com
2024-02-09drm/dp: switch drm_dp_vsc_sdp_log() to struct drm_printerJani Nikula
Use the existing drm printer infrastructure instead of local macros. Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Luca Coelho <luciano.coelho@intel.com> Acked-by: Maxime Ripard <mripard@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/cdf8faf272d345de215feb6ececba384ecaecdb4.1705410327.git.jani.nikula@intel.com
2024-01-18Merge tag 'i2c-for-6.8-rc1-rebased' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c updates from Wolfram Sang: "This removes the currently unused CLASS_DDC support (controllers set the flag, but there is no client to use it). Also, CLASS_SPD support gets simplified to prepare removal in the future. Class based instantiation is not recommended these days anyhow. Furthermore, I2C core now creates a debugfs directory per I2C adapter. Current bus driver users were converted to use it. Finally, quite some driver updates. Standing out are patches for the wmt-driver which is refactored to support more variants. This is the rebased pull request where a large series for the designware driver was dropped" * tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits) MAINTAINERS: use proper email for my I2C work i2c: stm32f7: add support for stm32mp25 soc i2c: stm32f7: perform I2C_ISR read once at beginning of event isr dt-bindings: i2c: document st,stm32mp25-i2c compatible i2c: stm32f7: simplify status messages in case of errors i2c: stm32f7: perform most of irq job in threaded handler i2c: stm32f7: use dev_err_probe upon calls of devm_request_irq i2c: i801: Add lis3lv02d for Dell XPS 15 7590 i2c: i801: Add lis3lv02d for Dell Precision 3540 i2c: wmt: Reduce redundant: REG_CR setting i2c: wmt: Reduce redundant: function parameter i2c: wmt: Reduce redundant: clock mode setting i2c: wmt: Reduce redundant: wait event complete i2c: wmt: Reduce redundant: bus busy check i2c: mux: reg: Remove class-based device auto-detection support i2c: make i2c_bus_type const dt-bindings: at24: add ROHM BR24G04 eeprom: at24: use of_match_ptr() i2c: cpm: Remove linux,i2c-index conversion from be32 i2c: imx: Make SDA actually optional for bus recovering ...
2024-01-18drm: remove I2C_CLASS_DDC supportHeiner Kallweit
After removal of the legacy EEPROM driver and I2C_CLASS_DDC support in olpc_dcon there's no i2c client driver left supporting I2C_CLASS_DDC. Class-based device auto-detection is a legacy mechanism and shouldn't be used in new code. So we can remove this class completely now. Acked-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2023-11-23Merge tag 'drm-intel-next-2023-11-23' of ↵Daniel Vetter
git://anongit.freedesktop.org/drm/drm-intel into drm-next drm/i915 feature pull for v6.8: Features and functionality: - Major DP MST improvements on bandwidth management, DSC (Imre, Stan, Ville) - DP panel replay enabling (Animesh, Jouni) - MTL C20 phy state verification (Mika) - MTL DP DSC fractional bpp support (Ankit, Vandita, Swati, Imre) - Audio fastset support (Ville) Refactoring and cleanups: - Use dma fence interfaces instead of i915_sw_fence (Jouni) - Separate gem and display code (Jouni, Juha-Pekka) - AUX register macro refactoring (Jani) - Separate display module/device parameters from the rest (Jouni) - Move display capabilities debugfs under display (Vinod) - Makefile cleanup (Jani) - Register cleanups (Ville) - Enginer iterator cleanups (Tvrtko) - Move display lock inits under display/ (Jani) - VLV/CHV DPIO PHY register and interface refactoring (Jani) - DSI VBT sequence refactoring (Jani, Andy Shevchenko) - C10/C20 PHY PLL hardware readout and calculation abstractions (Lucas) - DPLL code cleanups (Ville) - Cleanup PXP plane protection checks (Jani) Fixes: - Replace VLV/CHV DSI GPIO direct access with proper GPIO API usage (Andy Shevchenko) - Fix VLV/CHV DSI GPIO wrong initial value (Hans de Goede) - Fix UHBR data, link M/N/TU and PBN values (Imre) - Fix HDCP state on an enable/disable cycle (Suraj) - Fix DP MST modeset sequence to be according to spec (Ville) - Improved atomicity for multi-pipe commits (Ville) - Update URLs in i915 MAINTAINERS entry and code (Jani) - Check for VGA converter presence in eDP probe (Ville) - Fix surface size checks (Ville) - Fix LNL port/phy assignment (Lucas) - Reset C10/C20 message bus harder to avoid sporadic failures (Mika) - Fix bogus VBT HDMI level shift on BDW (Ville) - Add workaround for LNL underruns when enabling FBC (Vinod) - DSB refactoring (Animesh) - DPT refactoring (Juha-Pekka) - Disable DSC on DP MST on ICL (Imre) - Fix PSR VSC packet setup timing (Mika) - Fix LUT rounding and conversions (Ville) DRM core display changes: - DP MST fixes, helpers, refactoring to support bandwidth management (Imre) - DP MST PBN divider value refactoring and fixes (Imre) - DPCD register definitions (Ankit, Imre) - Add helper to get DSC bpp precision (Ankit) - Fix color LUT rounding (Ville) From: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/87v89sl2ao.fsf@intel.com [sima: Some conflicts in the amdgpu dp mst code] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2023-11-14drm/display/dp: Add helper function to get DSC bpp precisionAnkit Nautiyal
Add helper to get the DSC bits_per_pixel precision for the DP sink. Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com> Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn> Acked-by: Maxime Ripard <mripard@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20231110101020.4067342-2-ankit.k.nautiyal@intel.com
2023-11-08drm/dp: Add helpers to calculate the link BW overheadImre Deak
Add helpers drivers can use to calculate the BW allocation overhead - due to SSC, FEC, DSC and data alignment on symbol cycles - and the channel coding efficiency - due to the 8b/10b, 128b/132b encoding. On 128b/132b links the FEC overhead is part of the coding efficiency, so not accounted for in the BW allocation overhead. The drivers can use these functions to calculate a ratio, controlling the stream symbol insertion rate of the source device in each SST TU or MST MTP frame. Drivers can calculate this m/n = (pixel_data_rate * drm_dp_bw_overhead()) / (link_data_rate * drm_dp_bw_channel_coding_efficiency()) ratio for a given link and pixel stream and with that the slots_per_mtp = CEIL(64 * m / n) allocated slots per MTP for the stream in a link frame and with that the pbn = slots_per_mtp * drm_mst_get_pbn_divider() allocated PBNs for the stream on the MST link path. Take drm_dp_bw_overhead() into use in drm_dp_calc_pbn_mode(), for drivers calculating the PBN value directly. v2: - Add dockbook description to drm_dp_bw_channel_coding_efficiency(). (LKP). - Clarify the way m/n ratio is calculated in the commit log. v3: - Fix compile breakage for !CONFIG_BACKLIGHT_CLASS_DEVICE. (LKP) - Account for FEC_PM overhead (+ 0.0015625 %), add comment with the formula to calculate the total FEC overhead. (Ville) v4: - Rename DRM_DP_OVERHEAD_SSC to DRM_DP_OVERHEAD_SSC_REF_CLK. (Ville) v5: - Clarify in the commit log what MTP means. - Simplify the commit log's formula to calculate PBN. Cc: Lyude Paul <lyude@redhat.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: kernel test robot <lkp@intel.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> (v2) Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231107001505.3370108-1-imre.deak@intel.com
2023-11-08drm/dp_mst: Add HBLANK expansion quirk for Synaptics MST hubsImre Deak
Add a quirk for Synaptics MST hubs, which require a workaround - at leat on i915 - for some modes, on which the hub applies HBLANK expansion. These modes will only work by enabling DSC decompression for them, a follow-up patch will do this in i915. v2: - Fix the quirk name in its DocBook description. Cc: Lyude Paul <lyude@redhat.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-9-imre.deak@intel.com
2023-10-11Merge drm/drm-next into drm-misc-nextThomas Zimmermann
Updating drm-misc-next to the state of Linux v6.6-rc2. Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
2023-10-05drm/dp: switch drm_dp_downstream_*() helpers to struct drm_edidJani Nikula
Prefer struct drm_edid where possible. With limited users for the drm_dp_downstream_*() helpers, this is fairly straightforward. Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231004162149.2802113-1-jani.nikula@intel.com
2023-08-30drm/display/dp: Assume 8 bpc support when DSC is supportedAnkit Nautiyal
As per DP v1.4, a DP DSC Sink device shall support 8bpc in DPCD 6Ah. Apparently some panels that do support DSC, are not setting the bit for 8bpc. So always assume 8bpc support by DSC decoder, when DSC is claimed to be supported. v2: Use helper to get check dsc support. (Ankit) v3: Fix styling and other typos. (Jani) Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230824125121.840298-2-ankit.k.nautiyal@intel.com
2023-06-01drm/display/dp_mst: Replace all non-returning strlcpy with strscpyAzeem Shaikh
strlcpy() reads the entire source buffer first. This read may exceed the destination size limit. This is both inefficient and can lead to linear read overflows if a source string is not NUL-terminated [1]. In an effort to remove strlcpy() completely [2], replace strlcpy() here with strscpy(). No return values were used, so direct replacement is safe. [1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy [2] https://github.com/KSPP/linux/issues/89 Signed-off-by: Azeem Shaikh <azeemshaikh38@gmail.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20230522155124.2336545-1-azeemshaikh38@gmail.com
2022-10-07Merge tag 'driver-core-6.1-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core updates from Greg KH: "Here is the big set of driver core and debug printk changes for 6.1-rc1. Included in here is: - dynamic debug updates for the core and the drm subsystem. The drm changes have all been acked by the relevant maintainers - kernfs fixes for syzbot reported problems - kernfs refactors and updates for cgroup requirements - magic number cleanups and removals from the kernel tree (they were not being used and they really did not actually do anything) - other tiny cleanups All of these have been in linux-next for a while with no reported issues" * tag 'driver-core-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (74 commits) docs: filesystems: sysfs: Make text and code for ->show() consistent Documentation: NBD_REQUEST_MAGIC isn't a magic number a.out: restore CMAGIC device property: Add const qualifier to device_get_match_data() parameter drm_print: add _ddebug descriptor to drm_*dbg prototypes drm_print: prefer bare printk KERN_DEBUG on generic fn drm_print: optimize drm_debug_enabled for jump-label drm-print: add drm_dbg_driver to improve namespace symmetry drm-print.h: include dyndbg header drm_print: wrap drm_*_dbg in dyndbg descriptor factory macro drm_print: interpose drm_*dbg with forwarding macros drm: POC drm on dyndbg - use in core, 2 helpers, 3 drivers. drm_print: condense enum drm_debug_category debugfs: use DEFINE_SHOW_ATTRIBUTE to define debugfs_regset32_fops driver core: use IS_ERR_OR_NULL() helper in device_create_groups_vargs() Documentation: ENI155_MAGIC isn't a magic number Documentation: NBD_REPLY_MAGIC isn't a magic number nbd: remove define-only NBD_MAGIC, previously magic number Documentation: FW_HEADER_MAGIC isn't a magic number Documentation: EEPROM_MAGIC_VALUE isn't a magic number ...
2022-09-28drm/dp: Don't rewrite link config when setting phy test patternKhaled Almahallawy
The sequence for Source DP PHY CTS automation is [2][1]: 1- Emulate successful Link Training(LT) 2- Short HPD and change link rates and number of lanes by LT. (This is same flow for Link Layer CTS) 3- Short HPD and change PHY test pattern and swing/pre-emphasis levels (This step should not trigger LT) The problem is with DP PHY compliance setup as follow: [DPTX + on board LTTPR]------Main Link--->[Scope] ^ | | | | | ----------Aux Ch------>[Aux Emulator] At step 3, before writing TRAINING_LANEx_SET/LINK_QUAL_PATTERN_SET to declare the pattern/swing requested by scope, we write link config in LINK_BW_SET/LANE_COUNT_SET on a port that has LTTPR. As LTTPR snoops aux transaction, LINK_BW_SET/LANE_COUNT_SET writes indicate a LT will start [Check DP 2.0 E11 -Sec 3.6.8.2 & 3.6.8.6.3], and LTTPR will reset the link and stop sending DP signals to DPTX/Scope causing the measurements to fail. Note that step 3 will not trigger LT and DP link will never recovered by the Aux Emulator/Scope. The reset of link can be tested with a monitor connected to LTTPR port simply by writing to LINK_BW_SET or LANE_COUNT_SET as follow igt/tools/dpcd_reg write --offset=0x100 --value 0x14 --device=2 OR printf '\x14' | sudo dd of=/dev/drm_dp_aux2 bs=1 count=1 conv=notrunc seek=$((0x100)) This single aux write causes the screen to blank, sending short HPD to DPTX, setting LINK_STATUS_UPDATE = 1 in DPCD 0x204, and triggering LT. As stated in [1]: "Before any TX electrical testing can be performed, the link between a DPTX and DPRX (in this case, a piece of test equipment), including all LTTPRs within the path, shall be trained as defined in this Standard." In addition, changing Phy pattern/Swing/Pre-emphasis (Step 3) uses the same link rate and lane count applied on step 2, so no need to redo LT. The fix is to not rewrite link config in step 3, and just writes TRAINING_LANEx_SET and LINK_QUAL_PATTERN_SET [1]: DP 2.0 E11 - 3.6.11.1 LTTPR DPTX_PHY Electrical Compliance [2]: Configuring UnigrafDPTC Controller - Automation Test Sequence https://www.keysight.com/us/en/assets/9922-01244/help-files/ D9040DPPC-DisplayPort-Test-Software-Online-Help-latest.chm Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Or Cochvi <or.cochvi@intel.com> Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220916054900.415804-1-khaled.almahallawy@intel.com
2022-09-24drm: POC drm on dyndbg - use in core, 2 helpers, 3 drivers.Jim Cromie
Use DECLARE_DYNDBG_CLASSMAP across DRM: - in .c files, since macro defines/initializes a record - in drivers, $mod_{drv,drm,param}.c ie where param setup is done, since a classmap is param related - in drm/drm_print.c since existing __drm_debug param is defined there, and we ifdef it, and provide an elaborated alternative. - in drm_*_helper modules: dp/drm_dp - 1st item in makefile target drivers/gpu/drm/drm_crtc_helper.c - random pick iirc. Since these modules all use identical CLASSMAP declarations (ie: names and .class_id's) they will all respond together to "class DRM_UT_*" query-commands: :#> echo class DRM_UT_KMS +p > /proc/dynamic_debug/control NOTES: This changes __drm_debug from int to ulong, so BIT() is usable on it. DRM's enum drm_debug_category values need to sync with the index of their respective class-names here. Then .class_id == category, and dyndbg's class FOO mechanisms will enable drm_dbg(DRM_UT_KMS, ...). Though DRM needs consistent categories across all modules, thats not generally needed; modules X and Y could define FOO differently (ie a different NAME => class_id mapping), changes are made according to each module's private class-map. No callsites are actually selected by this patch, since none are class'd yet. Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Link: https://lore.kernel.org/r/20220912052852.1123868-3-jim.cromie@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-30drm/dp: add drm_dp_phy_name() for getting DP PHY nameJani Nikula
Add a helper for getting the DP PHY name. In the interest of caller simplicity and to avoid allocations and passing in of buffers, duplicate the const strings to return. It's a minor penalty to pay for simplicity in all the call sites. v2: Rebase, add kernel-doc, ensure non-NULL always Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/b08dc12a7e621a48ec35546d6cd1ed4b1434810d.1660553850.git.jani.nikula@intel.com
2022-07-19drm:delete the repeated word "the" in commentsshaomin Deng
remove the rebundant word "the" from comments. Signed-off-by: shaomin Deng <dengshaomin@cdjrlc.com> Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220718151154.9628-1-dengshaomin@cdjrlc.com
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-29 14:36:46 +0000