| Age | Commit message (Collapse) | Author |
|---|
|
The tc358768 driver follows the drm_encoder->crtc pointer that is
deprecated and shouldn't be used by atomic drivers.
Fortunately, the atomic hooks provide the drm_atomic_state and we can
access our current CRTC from that, going from the bridge to its encoder,
to its connector, and to its CRTC.
Let's convert this bridge driver to atomic so we can get rid of the
drm_encoder->crtc dereference.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-bridge-connector-v6-15-511c54a604fb@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
The tc358768 bridge driver, if enabling it fails, tries to disable it.
This is pretty uncommon in bridge drivers, and also stands in the way
for further reworks.
Worse, since pre_enable and enable aren't expected to fail, disable and
post_disable might be called twice: once to handle the failure, and once
to actually disable the bridge.
Since post_disable uses regulators and clocks, this would lead to enable
count imbalances.
In order to prevent that imbalance, and to allow further reworks, let's
drop the calls to disable and post_disable, but keep the warning to let
users know about what's going on.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-bridge-connector-v6-14-511c54a604fb@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
The drm_bridge structure contains an encoder pointer that is widely used
by bridge drivers. This pattern is largely documented as deprecated in
other KMS entities for atomic drivers.
However, one of the main use of that pointer is done in attach to just
call drm_bridge_attach on the next bridge to add it to the bridge list.
While this dereferences the bridge->encoder pointer, it's effectively
the same encoder the bridge was being attached to.
We can make it more explicit by adding the encoder the bridge is
attached to to the list of attach parameters. This also removes the need
to dereference bridge->encoder in most drivers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-bridge-connector-v6-1-511c54a604fb@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove commas after the sentinel entries.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Liu Ying <victor.liu@nxp.com> # ite-it6263.c
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241204105827.1682632-2-u.kleine-koenig@baylibre.com
|
|
Pull drm updates from Dave Airlie:
"There's a lot of rework, the panic helper support is being added to
more drivers, v3d gets support for HW superpages, scheduler
documentation, drm client and video aperture reworks, some new
MAINTAINERS added, amdgpu has the usual lots of IP refactors, Intel
has some Pantherlake enablement and xe is getting some SRIOV bits, but
just lots of stuff everywhere.
core:
- split DSC helpers from DP helpers
- clang build fixes for drm/mm test
- drop simple pipeline support for gem vram
- document submission error signaling
- move drm_rect to drm core module from kms helper
- add default client setup to most drivers
- move to video aperture helpers instead of drm ones
tests:
- new framebuffer tests
ttm:
- remove swapped and pinned BOs from TTM lru
panic:
- fix uninit spinlock
- add ABGR2101010 support
bridge:
- add TI TDP158 support
- use standard PM OPS
dma-fence:
- use read_trylock instead of read_lock to help lockdep
scheduler:
- add errno to sched start to report different errors
- add locking to drm_sched_entity_modify_sched
- improve documentation
xe:
- add drm_line_printer
- lots of refactoring
- Enable Xe2 + PES disaggregation
- add new ARL PCI ID
- SRIOV development work
- fix exec unnecessary implicit fence
- define and parse OA sync props
- forcewake refactoring
i915:
- Enable BMG/LNL ultra joiner
- Enable 10bpx + CCS scanout on ICL+, fp16/CCS on TGL+
- use DSB for plane/color mgmt
- Arrow lake PCI IDs
- lots of i915/xe display refactoring
- enable PXP GuC autoteardown
- Pantherlake (PTL) Xe3 LPD display enablement
- Allow fastset HDR infoframe changes
- write DP source OUI for non-eDP sinks
- share PCI IDs between i915 and xe
amdgpu:
- SDMA queue reset support
- SMU 13.0.6, JPEG 4.0.3 updates
- Initial runtime repartitioning support
- rework IP structs for multiple IP instances
- Fetch EDID from _DDC if available
- SMU13 zero rpm user control
- lots of fixes/cleanups
amdkfd:
- Increase event FIFO size
- add topology cap flag for per queue reset
msm:
- DPU:
- SA8775P support
- (disabled by default) MSM8917, MSM8937, MSM8953 and MSM8996 support
- Enable large framebuffer support
- Drop MSM8998 and SDM845
- DP:
- SA8775P support
- GPU:
- a7xx preemption support
- Adreno A663 support
ast:
- warn about unsupported TX chips
ivpu:
- add coredump
- add pantherlake support
rockchip:
- 4K@60Hz display enablement
- generate pll programming tables
panthor:
- add timestamp query API
- add realtime group priority
- add fdinfo support
etnaviv:
- improve handling of DMA address limits
- improve GPU hangcheck
exynos:
- Decon Exynos7870 support
mediatek:
- add OF graph support
omap:
- locking fixes
bochs:
- convert to gem/shmem from simpledrm
v3d:
- support big/super pages
- add gemfs
vc4:
- BCM2712 support refactoring
- add YUV444 format support
udmabuf:
- folio related fixes
nouveau:
- add panic support on nv50+"
* tag 'drm-next-2024-11-21' of https://gitlab.freedesktop.org/drm/kernel: (1583 commits)
drm/xe/guc: Fix dereference before NULL check
drm/amd: Fix initialization mistake for NBIO 7.7.0
Revert "drm/amd/display: parse umc_info or vram_info based on ASIC"
drm/amd/display: Fix failure to read vram info due to static BP_RESULT
drm/amdgpu: enable GTT fallback handling for dGPUs only
drm/amd/amdgpu: limit single process inside MES
drm/fourcc: add AMD_FMT_MOD_TILE_GFX9_4K_D_X
drm/amdgpu/mes12: correct kiq unmap latency
drm/amdgpu: Support vcn and jpeg error info parsing
drm/amd : Update MES API header file for v11 & v12
drm/amd/amdkfd: add/remove kfd queues on start/stop KFD scheduling
drm/amdkfd: change kfd process kref count at creation
drm/amdgpu: Cleanup shift coding style
drm/amd/amdgpu: Increase MES log buffer to dump mes scratch data
drm/amdgpu: Implement virt req_ras_err_count
drm/amdgpu: VF Query RAS Caps from Host if supported
drm/amdgpu: Add msg handlers for SRIOV RAS Telemetry
drm/amdgpu: Update SRIOV Exchange Headers for RAS Telemetry Support
drm/amd/display: 3.2.309
drm/amd/display: Adjust VSDB parser for replay feature
...
|
|
Wait for the command transmission to be completed in the DSI transfer
function polling for the dc_start bit to go back to idle state after the
transmission is started.
This is documented in the datasheet and failures to do so lead to
commands corruption.
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240926141246.48282-1-francesco@dolcini.it
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240926141246.48282-1-francesco@dolcini.it
|
|
"data-lines" property is way too similar to "data-lanes". It is also
duplicating "bus-width" from video-interfaces.yaml schema. "data-lines"
was deprecated in the bindings and "bus-width" is preferred, so parse it
instead while keeping things backwards compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241003133904.69244-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241003133904.69244-2-krzysztof.kozlowski@linaro.org
|
|
The DSI horizontal timing calculations done by the driver seem to often
lead to underflows or overflows, depending on the videomode.
There are two main things the current driver doesn't seem to get right:
DSI HSW and HFP, and VSDly. However, even following Toshiba's
documentation it seems we don't always get a working display.
This patch attempts to fix the horizontal timings for DSI event mode, and
on a system with a DSI->HDMI encoder, a lot of standard HDMI modes now
seem to work. The work relies on Toshiba's documentation, but also quite
a bit on empirical testing.
This also adds timing related debug prints to make it easier to improve
on this later.
The DSI pulse mode has only been tested with a fixed-resolution panel,
which limits the testing of different modes on DSI pulse mode. However,
as the VSDly calculation also affects pulse mode, so this might cause a
regression.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-12-31725f008a50@ideasonboard.com
|
|
The tc358768_ns_to_cnt() is, most likely, supposed to do a div-round-up
operation, but it misses subtracting one from the dividend.
Fix this by just using DIV_ROUND_UP().
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-11-31725f008a50@ideasonboard.com
|
|
The driver defines TC358768_PRECISION as 1000, and uses "nsk" to refer
to clock periods. The original author does not remember where all this
came from. Effectively the driver is using picoseconds as the unit for
clock periods, yet referring to them by "nsk".
Clean this up by just saying the periods are in picoseconds.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-10-31725f008a50@ideasonboard.com
|
|
The Toshiba documentation talks about HSByteClk when referring to the
DSI HS byte clock, whereas the driver uses 'dsibclk' name. Also, in a
few places the driver calculates the byte clock from the DSI clock, even
if the byte clock is already available in a variable.
To align the driver with the documentation, change the 'dsibclk'
variable to 'hsbyteclk'. This also make it easier to visually separate
'dsibclk' and 'dsiclk' variables.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-9-31725f008a50@ideasonboard.com
|
|
Simplify the code by capturing the priv->dev value to dev variable, and
use it.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-8-31725f008a50@ideasonboard.com
|
|
The driver debug prints DSI related timings as raw register values in
hex. It is much more useful to see the "logical" value of the timing,
not the register value.
Change the prints to print the values separately, in case a single
register contains multiple values, and use %u to have it in a more human
consumable form.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-7-31725f008a50@ideasonboard.com
|
|
The TC358768 documentation uses HFP, HBP, etc. values to deal with the
video mode, while the driver currently uses the DRM display mode
(htotal, hsync_start, etc).
Change the driver to convert the DRM display mode to struct videomode,
which then allows us to use the same units the documentation uses. This
makes it much easier to work on the code when using the TC358768
documentation as a reference.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-6-31725f008a50@ideasonboard.com
|
|
As is quite common, some of TC358768's PLL register fields are to be
programmed with (value - 1). Specifically, the FBD and PRD, multiplier
and divider, are such fields.
However, what the driver currently does is that it considers that the
formula used for PLL rate calculation is:
RefClk * [(FBD + 1)/ (PRD + 1)] * [1 / (2^FRS)]
where FBD and PRD are values directly from the registers, while a more
sensible way to look at it is:
RefClk * FBD / PRD * (1 / (2^FRS))
and when the FBD and PRD values are written to the registers, they will
be subtracted by one.
Change the driver accordingly, as it simplifies the PLL code.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-5-31725f008a50@ideasonboard.com
|
|
The driver has a few places where it does:
if (thing_is_enabled_in_config)
update_thing_bit_in_hw()
This means that if the thing is _not_ enabled, the bit never gets
cleared. This affects the h/vsyncs and continuous DSI clock bits.
Fix the driver to always update the bit.
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-4-31725f008a50@ideasonboard.com
|
|
As the TC358768 is a DPI to DSI bridge, the DSI side does not need to
define h/v sync polarities. This means that sometimes we have a mode
without defined sync polarities, which does not work on the DPI side.
Add a mode_fixup hook to default to positive sync polarities.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-3-31725f008a50@ideasonboard.com
|
|
smatch reports:
drivers/gpu/drm/bridge/tc358768.c:223 tc358768_update_bits() error: uninitialized symbol 'orig'.
Fix this by bailing out from tc358768_update_bits() if the
tc358768_read() produces an error.
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-2-31725f008a50@ideasonboard.com
|
|
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526090709.1517297-1-u.kleine-koenig@pengutronix.de
|
|
Remove unneeded stray semicolon.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305152341.oiSjRpv6-lkp@intel.com/
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230515184408.9421-1-francesco@dolcini.it
|
|
Remove the unused phy_delay_nsk variable, before it was wrongly used
to compute some register value, the fixed computation is no longer using
it and therefore can be removed.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-10-francesco@dolcini.it
|
|
Correct computation of THS_TRAILCNT register.
This register must be set to a value that ensure that
THS_TRAIL > 60 ns + 4 x UI
and
THS_TRAIL > 8 x UI
and
THS_TRAIL < TEOT
with
TEOT = 105 ns + (12 x UI)
with the actual value of THS_TRAIL being
(1 + THS_TRAILCNT) x ByteClk cycle + ((1 to 2) + 2) xHSBYTECLK cycle +
- (PHY output delay)
with PHY output delay being about
(8 + (5 to 6)) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-9-francesco@dolcini.it
|
|
Correct computation of TXTAGOCNT register.
This register must be set to a value that ensure that the
TTA-GO period = (4 x TLPX)
with the actual value of TTA-GO being
4 x (TXTAGOCNT + 1) x (HSByteClk cycle)
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-8-francesco@dolcini.it
|
|
Correct computation of THS_ZEROCNT register.
This register must be set to a value that ensure that
THS_PREPARE + THS_ZERO > 145ns + 10*UI
with the actual value of (THS_PREPARE + THS_ZERO) being
((1 to 2) + 1 + (TCLK_ZEROCNT + 1) + (3 to 4)) x ByteClk cycle +
+ HSByteClk x (2 + (1 to 2)) + (PHY delay)
with PHY delay being about
(8 + (5 to 6)) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-7-francesco@dolcini.it
|
|
Correct computation of TCLK_TRAILCNT register.
The driver does not implement non-continuous clock mode, so the actual
value doesn't make a practical difference yet. However this change also
ensures that the value does not write to reserved registers bits in case
of under/overflow.
This register must be set to a value that ensures that
TCLK-TRAIL > 60ns
and
TEOT <= (105 ns + 12 x UI)
with the actual value of TCLK-TRAIL being
(TCLK_TRAILCNT + (1 to 2)) xHSByteClkCycle +
(2 + (1 to 2)) * HSBYTECLKCycle - (PHY output delay)
with PHY output delay being about
(2 to 3) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-2-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-3-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-4-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-5-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-2-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-3-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-4-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-5-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-2-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-3-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-4-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-5-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-2-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-3-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-4-francesco@dolcini.it
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-5-francesco@dolcini.it
|
|
Correct computation of TCLK_ZEROCNT register.
This register must be set to a value that ensure that
(TCLK-PREPARECNT + TCLK-ZERO) > 300ns
with the actual value of (TCLK-PREPARECNT + TCLK-ZERO) being
(1 to 2) + (TCLK_ZEROCNT + 1)) x HSByteClkCycle + (PHY output delay)
with PHY output delay being about
(2 to 3) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-5-francesco@dolcini.it
|
|
Correctly compute the PLL target frequency, the current formula works
correctly only when the input bus width is 24bit, actually to properly
compute the PLL target frequency what is relevant is the bits-per-pixel
on the DSI link.
No regression expected since the DSI format is currently hard-coded as
MIPI_DSI_FMT_RGB888.
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-4-francesco@dolcini.it
|
|
According to Toshiba documentation the PLL input clock after the divider
should be not less than 4MHz, fix the PLL parameters computation
accordingly.
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-3-francesco@dolcini.it
|
|
Always enable HS video mode setting the TXMD bit, without this change no
video output is present with DSI sinks that are setting
MIPI_DSI_MODE_LPM flag (tested with LT8912B DSI-HDMI bridge).
Previously the driver was enabling HS mode only when the DSI sink was
not explicitly setting the MIPI_DSI_MODE_LPM, however this is not
correct.
The MIPI_DSI_MODE_LPM is supposed to indicate that the sink is willing
to receive data in low power mode, however clearing the
TC358768_DSI_CONTROL_TXMD bit will make the TC358768 send video in
LP mode that is not the intended behavior.
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-2-francesco@dolcini.it
|
|
Add atomic_get_input_bus_fmts() implementation, tc358768 has a parallel
RGB input interface with the actual bus format depending on the amount
of parallel input data lines.
Without this change when the tc358768 is used with less than 24bit the
color mapping is completely wrong.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230330095941.428122-7-francesco@dolcini.it
|
|
Several source files include drm_crtc_helper.h without needing it or
only to get its transitive include statements; leading to unnecessary
compile-time dependencies.
Drop drm_crtc_helper.h where possible.
v2:
* update commit message (Sam)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230116131235.18917-8-tzimmermann@suse.de
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20221118224540.619276-34-uwe@kleine-koenig.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
|
|
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
TXTAGOCNT and RXTASURECNT bitfields of BTACNTRL1 register are swapped in
the code, correct them. Driver doesn't implement low power mode for now,
so this change doesn't make a practical difference yet.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # Asus TF700T
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> #TF700T
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211002233447.1105-6-digetx@gmail.com
|
|
Non-continuous clock mode doesn't work because driver doesn't support it
properly. The bridge driver programs wrong bitfields that are required by
the non-continuous mode (BTACNTRL1 register bitfields are swapped in the
code), but fixing them doesn't help.
Display panel of ASUS Transformer TF700T tablet supports non-continuous
mode and display doesn't work at all using that mode. There are no
device-trees that are actively using this DSI bridge in upstream yet,
so clearly the broken mode wasn't ever tested properly. It's a bit too
difficult to get LP mode working, hence let's disable the offending mode
for now and fall back to continuous mode.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # Asus TF700T
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> #TF700T
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211002233447.1105-5-digetx@gmail.com
|
|
Calculate video start delay based on the display timing instead
of hardcoding it to a default value. This fixes "trembling" display
output on Asus Transformer TF700T which uses Panasonic VVX10F004B00
display panel.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # Asus TF700T
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> #TF700T
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211002233447.1105-4-digetx@gmail.com
|
|
Support pulse-mode synchronization which is supported and used by simple
DSI panels like Panasonic VVX10F004B00.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # Asus TF700T
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> #TF700T
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211002233447.1105-3-digetx@gmail.com
|
|
The driver assumes that reference clock is always-enabled, but this is
hardware-dependent and not true for ASUS Transformer TF700T. Make driver
enable / disable the reference clock.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # Asus TF700T
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> #TF700T
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211002233447.1105-2-digetx@gmail.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.15:
UAPI Changes:
- Add modifiers for arm fixed rate compression.
Cross-subsystem Changes:
- Assorted dt binding fixes.
- Convert ssd1307fb to json-schema.
- Update a lot of irc channels to point to OFTC, as everyone moved there.
- Fix the same divide by zero for asilantfb, kyro, rivafb.
Core Changes:
- Document requirements for new atomic properties.
- Add drm_gem_fb_(begin/end)_cpu_access helpers, and use them in some drivers.
- Document drm_property_enum.value for bitfields.
- Add explicit _NO_ for MIPI_DSI flags that disable features.
- Assorted documentation fixes.
- Update fb_damage handling, and move drm_plane_enable_fb_damage_clips to core.
- Add logging and docs to RMFB ioctl.
- Assorted small fixes to dp_mst, master handling.
- Clarify drm lease usage.
Driver Changes:
- Assorted small fixes to panfrost, hibmc, bridge/nwl-dsi, rockchip, vc4.
- More drm -> linux irq conversions.
- Add support for some Logic Technologies and Multi-Inno panels.
- Expose phy-functionality for drm/rockchip, to allow controlling from the media subsystem.
- Add support for 2 AUO panels.
- Add damage handling to ssd1307fb.
- Improve FIFO handling on mxsfb.
- Assorted small fixes to vmwgfx, and bump version to 2.19 for the new ioctls.
- Improve sony acx424akp backlight handling.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a753221a-e23e-0dc4-7ca6-8c1b179738d0@linux.intel.com
|
|
Don't populate the const array frs_limits on the stack but instead make
it static. Makes the object code smaller by 128 bytes:
Before:
text data bss dec hex filename
24845 7440 64 32349 7e5d ./drivers/gpu/drm/bridge/tc358768.o
After:
text data bss dec hex filename
24749 7408 64 32221 7ddd ./drivers/gpu/drm/bridge/tc358768.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
Many of the DSI flags have names opposite to their actual effects,
e.g. MIPI_DSI_MODE_EOT_PACKET means that EoT packets will actually
be disabled. Fix this by including _NO_ in the flag names, e.g.
MIPI_DSI_MODE_NO_EOT_PACKET.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@samsung.com>
Reviewed-by: Xin Ji <xji@analogixsemi.com> # anx7625.c
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> # msm/dsi
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727094435.v3.1.I629b2366a6591410359c7fcf6d385b474b705ca2@changeid
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708121604.14292-1-grandmaster@al2klimov.de
|
|
When validating a mode, bridges may need to do so in the context of a
display, as specified by drm_display_info. An example is the meson
dw-hdmi bridge that needs to consider the YUV 4:2:0 output format to
perform clock calculations.
Bridges that need the display info currently retrieve it from the
drm_connector created by the bridge. This gets in the way of moving
connector creation out of bridge drivers. To make this possible, pass
the drm_display_info to drm_bridge_funcs .mode_valid().
Changes to the bridge drivers have been performed with the following
coccinelle semantic patch and have been compile-tested.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.mode_valid = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
identifier mode;
@@
enum drm_mode_status fn(
struct drm_bridge *bridge,
+ const struct drm_display_info *info,
const struct drm_display_mode *mode
)
{
...
}
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org> # for the nwl-dsi part:
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-11-laurent.pinchart+renesas@ideasonboard.com
|
|
Some older versions of gcc badly optimize code that passes
an inline function argument into another function by reference,
causing huge stack usage:
drivers/gpu/drm/bridge/tc358768.c: In function 'tc358768_bridge_pre_enable':
drivers/gpu/drm/bridge/tc358768.c:840:1: error: the frame size of 2256 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
Use a temporary variable as a workaround and add a comment pointing
to the gcc bug.
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428215408.4111675-1-arnd@arndb.de
|
|
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
|
|
Add basic support for the Toshiba TC358768 RGB to DSI bridge.
Not all the features of the TC358768 is implemented by the initial driver:
MIPI_DSI_MODE_VIDEO and MIPI_DSI_FMT_RGB888 is only supported and tested.
Only write is implemented for mipi_dsi_host_ops.transfer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200131111553.472-3-peter.ujfalusi@ti.com
|
