| Age | Commit message (Collapse) | Author |
|---|
|
[Why]
To know if the firmware is idle when logging.
[How]
Add the pwait status to the DMCUB diagnostics.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When analyzing some crash dumps, not all of the expected DMUB info was
available, so we want to add in-object storage for this data.
[How]
- dmub_srv_debug (renamed to dmub_timeout_info) is already a member of
dmub_diagnostic_data, therefore keep a dmub_diagnostic_data directly in
dmub_srv
- use dmub_srv->debug when collecting diagnostic info instead of stack
object to allow for easy inspection in crash dumps
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If we soft reset before halt finishes and there are outstanding
memory transactions then the memory interface may produce unexpected
results, such as out of order transactions when the firmware next runs.
These can manifest as random or unexpected load/store violations.
[How]
Increase the timeout before soft reset to ensure the DMCUB has quiesced.
This is effectively 1s maximum based on experimentation.
Use the enable bit check on DCN31 like we're doing on DCN35 and reorder
the reset writes to follow the HW programming guide.
Ensure we're reading SCRATCH7 instead of SCRATCH8 for the HALT code.
No current versions of DMCUB firmware use the SCRATCH8 boot bit to
dynamically switch where the HALT code goes to maintain backwards
compatibility with PSP.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 50f040c53ea9 ("drm/amd/display: Increase halt
timeout for DMCUB to 1s")
There's two issues here:
1. Each poll is closer to 10us than 1us so it stalls for 15s on PNP.
2. We're reading the wrong scratch register to check for the HALT code.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If we soft reset before halt finishes and there are outstanding
memory transactions then the memory interface may produce unexpected
results, such as out of order transactions when the firmware next runs.
These can manifest as random or unexpected load/store violations.
[How]
Increase the timeout before soft reset to ensure the DMCUB has quiesced.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Spread on DPREFCLK by 0.3 percent can have a negative effect on sink
when PHY SSC is also spread by 0.3 percent
[How]
Add boot option for DMU to lower PHY SSC
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The DP tunnel AUX reply is received through Outbox1. Print the Outbox1
status if an issue occurs.
Signed-off-by: Cruise <Cruise.Hung@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
- Add logging for first DMUB inbox message that timed out to diagnostic
data
- It is useful to track the first failed message for debug purposes
because once DMUB becomes hung (typically on a message), it will
remain hung and all subsequent messages. In these cases we're
interested in knowing which is the first message that failed.
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Read modify write hazards can occur when using a single shared scratch
register between driver and firmware leading to driver accessing DCN
in IPS2 and a system hang.
[How]
Add infrastructure for using REGION6 as a shared firmware state between
driver and firmware. This region is uncachable.
Replace the existing get/set idle calls with reads/writes to the
(volatile) shared firmware state blocks that a separated by at least
a cache line between firmware and driver.
Remove the workarounds that required rewriting/checking read modify
write hazards.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
To query the bits and print them out for debug purposes.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Cruise Hung <cruise.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
A number of parade TCONs are causing system hangs when utilized with
older DMUB firmware and PSR-SU. Some changes have been introduced into
DMUB firmware to add resilience against these failures.
Don't allow running PSR-SU unless on the newer firmware.
Cc: stable@vger.kernel.org
Cc: Sean Wang <sean.ns.wang@amd.com>
Cc: Marc Rossi <Marc.Rossi@amd.com>
Cc: Hamza Mahfooz <Hamza.Mahfooz@amd.com>
Cc: Tsung-hua (Ryan) Lin <Tsung-hua.Lin@amd.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2443
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
States may be desync after resume.
[How]
Sync sw state with hw state.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Dpia hpd interrupt processing is disabled when entering S4/S0i3 and
would be reenabled after detection completes during resuming. Because,
keeping hpd interrupts enabled during detection leads to multiple
detections for the same hpd transition. There is a S4 case where dpia
hpd interrupt is missed when driver is in transitioning from hpd
interrupt processing disable to enable and the display does not light
up.
[How]
- Added dmub inbox command DMUB_CMD__DPIA_HPD_INT_ENABLE to explicitly
control dmub to issue dpia hpd interrupt or not. If dpia hpd interrupt
is disabled, dmub will keep the hpd pending and post it once driver
reenables dpia hpd interrupt or when querying with
DMUB_CMD__QUERY_HPD_STATE.
- Added dmub boot option dpia_hpd_int_enable_supported to notify dmub
about whether DMUB_CMD__DPIA_HPD_INT_ENABLE command would be used.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Mustapha Ghaddar <Mustapha.Ghaddar@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DMUB Outbox0 read/write pointer not sync after resumed from S4.
And that caused old traces were sent to outbox.
[How]
Disable DMUB Outbox0 interrupt
and clear DMUB Outbox0 read/write pointer when resumes from S4.
And then enable Outbox0 interrupt before starts DMCUB.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Very low rate to cause memory access issue while resetting
DMCUB after the halt command was sent to it.
The process of stopping fw of DMCUB may be timeout, that means
it is not in idle state, such as the window frames may still be
kept in cache, so reset by force will cause MMHUB hang.
[HOW]
After the halt command was sent, keep checking the DMCUB state until
it is idle.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: hengzhou <Hengyong.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Boot up behaviour may differ depending on the Connection Manager
handling USB4 tunneling.
[How]
Send boot option to firmware to indicate Connection Manager.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Might potentially have truncation problem with the implicit casting
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
During Z10, root clock gating and memory low power registers needs to
to be restored if optimization is enabled in driver.
[How]
Added new DMUB boot option for root clock gating and memory low power.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DMUB binary is common for both A0 and B0. Hence, driver should
notify FW about the support for DPIA in B0.
[How]
Added dpia_supported bit in dmub_fw_boot_options and will be set
only for B0.
Assign dpia_supported to true before dm_dmub_hw_init
in B0 case.
v2: fix build without CONFIG_DRM_AMD_DC_DCN (Alex)
Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
B0 has pipe mux for DIGC and DIGD which can be connected to PHYF/PHYG or
PHYC/PHY D.
[How]
Based on chip internal hardware revision id determine it is B0 and set
DMUB scratch register so DMUBFW can connect the display pipe is
connected correctly to the dig.
Cc: Wayne Lin <wayne.lin@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Hansen <Hansen.Dsouza@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
To add support for dpia debug options.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When system is in Z10 HPD interrupts cannot fire, we may miss display
configuration changes.
[How]
When Zstate is enabled, if DMUB indicate DCN has lost power, do a
complete detection periodically.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If we're backdoor loading the DMCUB performs more work than just
the PHY reset so we can end up resetting before the cleanup has fully
finished.
[How]
Increase timeout, add udelay between spins to guarantee a minimum.
Reviewed-by: Roy Chan <roy.chan@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Otherwise we can end up processing whatever was left in the register
if the DMCUB was previously reset.
If DMCUB gets force reset too early from another client then we might
not have even acked the disable yet - causing DMCUB instantly shutdown
if the command was 10020000.
[How]
Move the GPINT clear outside of the reset loop and do it unconditionally
after the DMCUB has been properly reset.
Reviewed-by: Roy Chan <roy.chan@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why] On S4 resume we also need to fix detection of when to reload DMCUB
firmware because we're currently using the VBIOS version which isn't
compatible with the driver version.
[How] Update the hardware init check for DCN31 since it's the ASIC that
has this issue.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jude Shih <jude.shih@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Initializing was missing reg offsets for the dmcub test debug registers
causing assert
[How]
Add initialization
Reviewed-by: Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
dmub would notify x86 response time violation by GPINT_DATAOUT
[How]
1. Use GPINT_DATAOUT to trigger x86 interrupt
2. Register GPINT_DATAOUT interrupt handler.
3. Trigger ACR while GPINT_DATAOUT occurred.
Signed-off-by: Chun-Liang Chang <Chun-Liang.Chang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Extend existing support for DCN2.1 DMUB diagnostic logging to
DCN3.1 so we can collect useful information if the DMUB hangs.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
DMCU-B (Display Micro-Controller Unit B) is a display microcontroller
used for shared display functionality with BIOS and for advanced
power saving display features.
Extends the command header to include new DCN3.1 functionality.
Adds new interfaces to DC dmub interface as well for z-state support.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
