| Age | Commit message (Collapse) | Author |
|---|
|
[WHY]
For SQ128 pattern some vendor-specific overrides are required.
Previously a hardcoded clock gen source value was incorrectly programmed,
causing our override to retimer's clock source override to be ignored.
Due to some PHY issues on certain APU programs, we see failures on retimer
bypass ports extend to electrical testing downstream of PHY due to some host
clock jitter which the retimer follows.
[HOW]
Fix typo to use correct clock gen source override of 0xC4 rather than 0x4C.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
These are left required changes for dio encoder refactor.
[HOW]
1. original logic is separated by config option
2. new link encoder dp enable/disable code for dcn35
3. process fec only for DP 8b10b encoding
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
replace dio encoder access to work with new dio encoder
assignment.
[HOW}
1. before validation, access dio encoder by get_temp_dio_link_enc()
2. after validation, access dio encoder through pipe_ctx->link_res
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
The defines have also been updated with prefix AMD_ and atomfirmware.h
has been temporarily updated with both sets of defines to allow the
transition.
This update is being made to standardize workaround chip_cap flags,
in order to support more workaround flags in the future.
[HOW]
Updated EXT_DISPLAY_PATH_CAPS__DP_FIXED_VS_EN define, the flag is now
an enum masked by EXT_DISPLAY_PATH_CAPS__EXT_CHIP_MASK. All checks for
DP_FIXED_VS_EN are now performed by masking with EXT_CHIP_MASK and
checking for an exact match rather than the previous bitwise AND check.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
We like to have pretrain for dpia link so that dp and dp tunneling
have aligned behavior. The Main difficult for dpia pretrain is that
encoder can not get corresponded dpia port when link detection
in current implementation.
[HOW]
1. create enable/disable dpia output functions for dcn35 encoder
and have dpia_id and other necessary info as inputs.
2. dcn35 dpia use the new functions to enable/disable output.
3. have a option to enable/disable the change.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
We intend to consolidate dp tunneling and conventional dp link training.
[HOW]
1. Use the same link training entry for both dp and dpia
2. Move SET_CONFIG of non-transparent mode to dmub side
3. Add set_tps_notification dmub_cmd to notify tps request for
non-transparent dpia link training
4. Check dpcd request result and abort link training early if dpia
aux tunneling fails
5. Add option to avoid affect old product
6. Separately handle wait_time_microsec for dpia
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHAT & HOW]
Functions dp_enable_link_phy and dp_disable_link_phy can pass link_res
without initializing hpo_dp_link_enc and it is necessary to check for
null before dereferencing.
This fixes 1 FORWARD_NULL issue reported by Coverity.
Fixes: 0beca868cde8 ("drm/amd/display: Check link_res->hpo_dp_link_enc before using it")
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHAT & HOW]
Poniters, such as stream_enc and dc->bw_vbios, are null checked previously
in the same function, so Coverity warns "implies that stream_enc and
dc->bw_vbios might be null". They are used multiple times in the
subsequent code and need to be checked.
This fixes 10 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHAT & HOW]
Functions dp_enable_link_phy and dp_disable_link_phy can pass link_res
without initializing hpo_dp_link_enc and it is necessary to check for
null before dereferencing.
This fixes 2 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When building the kernel-doc, it complains with the below warning:
./drivers/gpu/drm/amd/display/dc/link/hwss/link_hwss_dio.h:1: warning: no structured comments found
./drivers/gpu/drm/amd/display/dc/link/hwss/link_hwss_dio.h:1: warning: no structured comments found
This warning was caused by the wrong use of the ':export:' and the lack
of function documentation in the file pointed under the ':internal:'.
This commit addresses those issues by relocating the overview
documentation to the correct C file, removing the ':export:' options,
and adding two simple kernel-doc to ensure that ':internal:' does not
have any warning.
Cc: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/dri-devel/20240715085918.68f5ecc9@canb.auug.org.au/
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Needed for PHY patterns as well to perform electrical compliance.
Also need to increase wait time from 30ms to 50ms to resolve very
intermittent UHBR20 link training failures.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
In order to support glitchless display clock ramping for virtual stream,
we must
turn on symclk for stream encoder. The code will power on phy and enable
symclk
for dio encoder during virtual stream dpms sequence.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY & HOW]
Make enable and disable sequences symmetric.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Input mode for the DIG FIFO should be programmed as part of stream
encoder setup.
[HOW]
Pre-calculate the pixels per cycle as part of the pixel clock params,
and program as part of stream encoder setup.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Avoid race condition which puts LTTPR into bad state during UHBR LT.
[HOW]
Delay 30ms between starting UHBR TPS1 PHY output and sending TPS1 via DPCD.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Need to fix some broken logic and sequencing in initial commit
[HOW]
Fix logic handling override deprogramming when exiting SQ128.
Don't exit early from dp_set_hw_lane_settings for DP2/FIXED_VS case.
Move LTTPR 128b/132b check out of requires_hwss and check during
runtime, as LTTPR caps are not populated on initial call.
Add pending_test_pattern to link state to allow HWSS to set FFE overrides
on retimer TX and/or skip setting APU TX FFE depending on requested pattern.
Use updated clock source for SQ128 override sequence.
Skip HW FFE preset programming when performing test pattern overrides.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For multi-GPU systems it is difficult to tell which GPU a particular
message is being printed for and that is undesirable because it
complicates debugging efforts. Also, the new macros allow us to enable
logging for particular parts of the codebase more selectively (since we
no longer need to throw everything at DRM_DEBUG_KMS()). So, for the
reasons outlined above we should switch to the new macros.
We can accomplish this by using the existing DC_LOGGER code to pass
around the relevant `struct drm_device` which will be fed to the new
macros in logger_types.h. Also, we must get rid of all instances of the
DC_LOG_.*() functions that are currently in amdgpu_dm since we don't use
the DC logger there and we can simply refer to the macros directly
there instead.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Certain retimer requires workarounds in order to correctly output test patterns.
[HOW]
Add vendor-specific aux sequences to program retimer's TX and pattern generator
when specific compliance test patterns are requested by sink.
Note: SQ128 w/a in DPMF mode only works in one flip orientation currently
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Using dig_stream_mapper, program symclk_en and symclk_fe_src_sel when
enabling or disabling the corresponding stream.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When RCO is enabled for symclk32_le we get failures during
DP2 link traing compliance tests.
[How]
Break out symclk32_le RCO into a separate function that is
called for hpo when link is enabled/disabled.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Drop dead code for Linux.
[How]
Remove all IS_FPGA_MAXIMUS_DC and IS_DIAG_DC
Reviewed-by: Ariel Bernstein <eric.bernstein@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
All dc subcomponents should call another dc component via function pointers
stored in a component structure. This is part of dc coding convention since
the beginning. The reason behind this is to improve encapsulation and
polymorphism. The function contract is extracted into a single link service
structure defined in link.h header file and implemented only in link_factory.c instead
of spreading across multiple files in link component file structure.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
dc_link contains over 30k line of code, the decision is to break it
down to files residing in link folder based on functionality. This
change is the last break down change which will remove dc_link.c
file after everything is broken down.
[how]
Move remaining dc_link.c functions into link_detection, link_dpms,
link_validation, link_resource, and link_fpga and remove dc_link.
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Temporarly merge dc_link_dp functions into dc_link for the
purpose of removing dc_link_dp files. This is a transitional
change for later commits where we will further refactor dc_link
file.
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
link component contains three sub folders:
accessories - utilities for improving testability, logging or tracing, doesn't impact
end user use cases.
protocols - specs defined protocols used in end user use cases
hwss - hwss owned link_hwss object, served as an abstraction layer in hwss to
access various types of encoder/phy/dpia endpoints in a unified interface.
sooner we will have files directly under link folder one for the implementation of
each major link behavior such as link_create, link_detect, link_validate
and link_set_dpms.
Reviewed-by: George Shen <George.Shen@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
