| Age | Commit message (Collapse) | Author |
|---|
|
The previous wrapper qcom_cc_really_probe takes the platform
device as parameter, which is limited to platform driver.
As for qca8k clock controller driver, which is registered as
the MDIO device, which also follows the qcom clock framework.
To commonize qcom_cc_really_probe, updating it to take the
struct device as parameter, so that the qcom_cc_really_probe
can be utilized by the previous platform device and the new
added MDIO device.
Also update the current clock controller drivers to take
&pdev->dev as parameter when calling qcom_cc_really_probe.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://lore.kernel.org/r/20240605124541.2711467-4-quic_luoj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
While the kernel is booting up, APSS PLL will be running at 800MHz with
GPLL0 as source. Once the cpufreq driver is available, APSS PLL will be
configured and select the rate based on the opp table and the source will
be changed to APSS_PLL_EARLY.
Without this patch, CPU Freq driver reports that CPU is running at 24MHz
instead of the 800MHz.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Link: https://lore.kernel.org/r/20230913-gpll_cleanup-v2-7-c8ceb1a37680@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Stromer Plus PLL found on IPQ53xx doesn't support dynamic
frequency scaling. To achieve the same, we need to park the APPS
PLL source to GPLL0, re configure the PLL and then switch the
source to APSS_PLL_EARLY.
To support this, register a clock notifier to get the PRE_RATE
and POST_RATE notification. Change the APSS PLL source to GPLL0
when PRE_RATE notification is received, then configure the PLL
and then change back the source to APSS_PLL_EARLY.
Additionally, not all SKUs of IPQ53xx support scaling. Hence,
do the above to the SKUs that support scaling.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/49422d258d67d33a2547fbb7f4f6e72d489c2301.1697781921.git.quic_varada@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
While fixing up the driver I noticed that my IPQ8074 board was hanging
after CPUFreq switched the frequency during boot, WDT would eventually
reset it.
So mark apcs_alias0_core_clk as critical since its the clock feeding the
CPU cluster and must never be disabled.
Fixes: 5e77b4ef1b19 ("clk: qcom: Add ipq6018 apss clock controller")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-3-robimarko@gmail.com
|
|
While working on IPQ8074 APSS driver it was discovered that IPQ6018 and
IPQ8074 use almost the same PLL and APSS clocks, however APSS driver is
currently broken.
More precisely apcs_alias0_clk_src is broken, it was added as regmap_mux
clock.
However after debugging why it was always stuck at 800Mhz, it was figured
out that its not regmap_mux compatible at all.
It is a simple mux but it uses RCG2 register layout and control bits, so
utilize the new clk_rcg2_mux_closest_ops to correctly drive it while not
having to provide a dummy frequency table.
While we are here, use ARRAY_SIZE for number of parents.
Tested on IPQ6018-CP01-C1 reference board and multiple IPQ8074 boards.
Fixes: 5e77b4ef1b19 ("clk: qcom: Add ipq6018 apss clock controller")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-2-robimarko@gmail.com
|
|
In case of error, the function dev_get_regmap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 5e77b4ef1b19 ("clk: qcom: Add ipq6018 apss clock controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200628023055.50608-1-weiyongjun1@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The CPU on Qualcomm ipq6018 devices are clocked primarily by a aplha PLL
and xo which are connected to a mux and enable block.
Add support for the mux and enable block which feeds the CPU on ipq6018
devices.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Link: https://lore.kernel.org/r/1592800092-20533-5-git-send-email-sivaprak@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
