| Age | Commit message (Collapse) | Author |
|---|
|
Common name for Ethernet controllers is "ethernet", not "eth", also
recommended by Devicetree specification in "Generic Names
Recommendation". Verified lack of impact using dtx_diff.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20250717142245.92492-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
STM32MP157F-DK2 board embeds a STM32MP157F SoC. This SoC contains the same
level of feature than a STM32MP157C SOC but A7 clock frequency can reach
800MHz, hence the inclusion of the newly introduced stm32mp15xf.dtsi.
As for other latest STM32 MPU families, STM32MP157F-DK2 relies on OP-TEE
SCMI services for SoC clock and reset controllers resources, and for PMIC,
now under OP-TEE control. That's why stm32mp157f-dk2-scmi.dtsi is
introduced, to move all clocks, resets and regulators to SCMI-based ones.
To "disable" SCMI, just need to comment stm32mp157f-dk2-scmi.dtsi inclusion
and to replace &scmi_v3v3 with &v3v3, then to disable arm_wdt and to enable
i2c4 and its subnodes for PMIC support by Linux. Reconfigure usbotg for
dual role with type-C support if needed.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20250603-stm32mp157f-dk2-v2-7-5be0854a9299@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Define the interrupt used by OP-TEE async notif on stm32mp15 scmi based
platforms.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Link: https://lore.kernel.org/r/20250603-stm32mp157f-dk2-v2-5-5be0854a9299@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Use the SCMI voltage domain bindings for internal regulators on stm32mp15.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20250603-stm32mp157f-dk2-v2-4-5be0854a9299@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Adopt generic node name 'typec' for stusb1600, which is the USB Type-C
controller on stm32mp157x Discovery Kits.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20250603-stm32mp157f-dk2-v2-2-5be0854a9299@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
This commit creates new file to manage security features and supported OPP
on STM32MP15xF SOCs. On STM32MP15xY, "Y" gives information:
-Y = A means no cryp IP and no secure boot + A7-CPU@650MHz.
-Y = C means cryp IP + optee + secure boot + A7-CPU@650MHz.
-Y = D means no cryp IP and no secure boot + A7-CPU@800MHz.
-Y = F means cryp IP + optee + secure boot + A7-CPU@800MHz.
It fullfills the initial STM32MP15x SoC diversity introduced by
commit 0eda69b6c5f9 ("ARM: dts: stm32: Manage security diversity
for STM32M15x SOCs").
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20250603-stm32mp157f-dk2-v2-1-5be0854a9299@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The commit 5725bce709db
("ASoC: simple-card-utils: Unify clock direction by clk_direction")
corrupts the audio on STM32MP15 DK sound cards.
The parent clock is not correctly set, because set_sai_ck_rate() is not
executed in stm32_sai_set_sysclk() callback.
This occurs because set_sysclk() is called with the wrong direction,
SND_SOC_CLOCK_IN instead of SND_SOC_CLOCK_OUT.
Add system-clock-direction-out property in SAI2A endpoint node of
STM32MP15XX-DKX device tree, to specify the MCLK clock direction.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20250521150418.488152-1-olivier.moysan@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The efuse device tree description already has the two labels pointing to
the efuse nodes that specify the mac-addresses to be used. Wire them up
to the ethernet nodes. This is enough to make barebox pick the right
mac-addresses and pass them to Linux.
Suggested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20250328171406.3307778-2-u.kleine-koenig@baylibre.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.16, round 1
Highlights:
----------
- MCU:
- Add low power timer on STM32F746
- Add STM32H747 High end MCU support. It embeds:
- dual-core (Cortex-M7 + Cortex-M4)
- up to 2 Mbytes flash
- 1 Mbyte of internal RAM
- Add STM32H747i-disco board support. Detailed information can be
found at:
https://www.st.com/en/evaluation-tools/stm32h747i-disco.html
- MPU:
- STM32MP13:
- Add VREFINT calibration support based on ADC.
- STMP32MP15:
- Add new Ultratronik Fly board support:
- based on STM32MP157C SoC
- 1GB of DDR3
- Several connections are available on this boards:
2*USB2.0, 1*USB2.0 MiniUSB, Debug UART, 1*UART, 1*USART,
SDcard, RJ45, ...
- STM32MP25:
- Add OCTOSPI support on STM32MP25 SoCs
- Add SPI NOR flash support on STM32MP257F-EV1 connected to OSPI1
- Add Low power timer TIMER (LPTIM) on STM32MP25 SoCs and use
LPTIM3 as low power broadcast timer on STM32MP257F-EV1.
* tag 'stm32-dt-for-v6.16-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (22 commits)
ARM: dts: stm32: add initial support for stm32mp157-ultra-fly-sbc board
MAINTAINERS: Add entry for ULTRATRONIK BOARD SUPPORT
dt-bindings: arm: stm32: Document Ultratronik's Fly board DT binding
dt-bindings: vendor-prefixes: Add Ultratronik
arm64: dts: st: use lptimer3 as tick broadcast source on stm32mp257f-ev1
arm64: dts: st: add low-power timer nodes on stm32mp251
arm64: defconfig: enable STM32 LP timer clockevent driver
arm64: dts: st: Add SPI NOR flash support on stm32mp257f-ev1 board
arm64: dts: st: Add ospi port1 pinctrl entries in stm32mp25-pinctrl.dtsi
arm64: dts: st: Add OMM node on stm32mp251
ARM: dts: stm32: support STM32h747i-disco board
ARM: dts: stm32: add an extra pin map for USART1 on stm32h743
ARM: dts: stm32: add pin map for UART8 controller on stm32h743
ARM: dts: stm32: add uart8 node for stm32h743 MCU
dt-bindings: clock: stm32h7: rename USART{7,8}_CK to UART{7,8}_CK
ARM: stm32: add a new SoC - STM32H747
dt-bindings: arm: stm32: add compatible for stm32h747i-disco board
ARM: dts: stm32h7-pinctrl: add _a suffix to u[s]art_pins phandles
ARM: dts: st: stm32: Align wifi node name with bindings
ARM: dts: stm32: add low power timer on STM32F746
...
Link: https://lore.kernel.org/r/2f101efb-6d58-48d8-983a-57e30a34827c@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add support for Ultratronik's stm32mp157c fly board. This board embeds
a STM32MP157c SOC and 1GB of DDR3. Several connections are available on
this boards: 2*USB2.0, 1*USB2.0 MiniUSB, Debug UART, 1*UART, 1*USART,
SDcard, RJ45, ...
This patch enables basic support for a kernel boot - SD-card or eMMC.
Signed-off-by: Goran Rađenović <goran.radni@gmail.com>
Link: https://lore.kernel.org/r/20250508143818.2574558-5-goran.radni@gmail.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The board includes an STM32H747XI SoC with the following resources:
- 2 Mbytes Flash
- 1 Mbyte SRAM
- LCD-TFT controller
- MIPI-DSI interface
- FD-CAN
- USB 2.0 high-speed/full-speed
- Ethernet MAC
- camera interface
Detailed information can be found at:
https://www.st.com/en/evaluation-tools/stm32h747i-disco.html
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250427074404.3278732-9-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add an additional pin map configuration for using the USART1 controller
on the stm32h743 MCU.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250427074404.3278732-8-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add a pin map configuration for using the UART8 controller on the
stm32h743 MCU.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250427074404.3278732-7-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add support for UART8 by applying the settings specified in the
reference manual RM0433.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250427074404.3278732-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Allow expanding possible configurations for the same peripheral,
consistent with the scheme adopted in Linux.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250427074404.3278732-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Since commit 3c3606793f7e ("dt-bindings: wireless: bcm4329-fmac: Use
wireless-controller.yaml schema"), bindings expect 'wifi' as node name:
stm32h750i-art-pi.dtb: bcrmf@1: $nodename:0: 'bcrmf@1' does not match '^wifi(@.*)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250424084706.105049-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add device tree node for the low power timer on the STM32F746.
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Link: https://lore.kernel.org/r/20250404143514.860126-1-ben.wolsieffer@hefring.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Set STM32 ADC1&2 as consumers of BSEC, to retrieve vrefint calibration
data on STM32MP13x SoCs.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20250403115954.1061528-3-olivier.moysan@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Describe vrefint calibration cell to be retrieved through bsec,
on STM32MP13x SoCs family.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20250403115954.1061528-2-olivier.moysan@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
They should be named "usb@".
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250330193833.21970-10-wsa+renesas@sang-engineering.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pull SoC devicetree updates from Arnd Bergmann:
"There is new support for additional on-chip devices on Apple,
Mediatek, Renesas, Rockchip, Samsung, Google, TI, ST, Nvidia and
Amlogic devices.
The Arm Morello reference platform gets a devicetree for booting in
normal aarch64 mode. The hardware supports experimental CHERI support,
which requires a modified kernel.
The AMD (formerly Xilinx) Versal NET SoC gets added, this is a
combined FPGA with Cortex-A78 CPUs in a SoC.
Six new ST STM32MP2 SoC variants are added. Like the earlier
STM32MP25, the MP211, MP213, MP215, MP231, MP233 and MP235 models are
based on one or two Cortex-A35 cores but each feature a different set
of I/O devices.
Mediatek MT8370 is a minor variation of MT8390 with fewer CPU and GPU
cores
Apple T2 is the baseboard management controller on earlier Intel CPU
based Macs, with 16 models now gaining initial support.
All the above come with dts files for the reference boards. In
addition, these boards are added for the SoCs that are already
supported:
- The Milk-V Jupiter board based on SpacemiT K1/M1
- NetCube Systems Kumquat board based on the 32-bit Allwinner V3s SoC
- Three boards based on 32-bit stm32mp1
- 11 distinct board variants from Toradex and one from Variscite, all
based on i.MX6
- Google Pixel Pro 6 phone based on gs101 (Tensor)
- Three additional variants of the i.MX8MP based "Skov" board
- A second variant of the i.MX95 EVK board
- Two boards based on Renesas SoCs
- Four boards based the Rockchip RK35xx series, plus the RK3588 'MNT
Reform 2' laptop"
* tag 'soc-dt-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (538 commits)
arm64: dts: Add gpio_intc node for Amlogic A5 SoCs
arm64: dts: Add gpio_intc node for Amlogic A4 SoCs
arm64: dts: hi3660: Add property for fixing CPUIdle
arm64: dts: rockchip: remove ethm0_clk0_25m_out from Sige5 gmac0
arm64: dts: marvell: Use preferred node names for "simple-bus"
arm64: dts: marvell: Drop unused CP11X_TYPE define
arm64: dts: marvell: Move arch timer and pmu nodes to top-level
arm64: dts: rockchip: Fix PWM pinctrl names
arm64: dts: rockchip: fix RK3576 SCMI clock IDs
dt-bindings: clock: rk3576: add SCMI clocks
arm64: dts: rockchip: Fix pcie reset gpio on Orange Pi 5 Max
arm64: dts: amd/seattle: Drop undocumented "spi-controller" properties
arm64: dts: amd/seattle: Fix bus, mmc, and ethernet node names
arm64: dts: amd/seattle: Move and simplify fixed clocks
arm64: dts: amd/seattle: Base Overdrive B1 on top of B0 version
arm64: dts: rockchip: Enable HDMI audio output for ArmSoM Sige7
arm64: dts: rockchip: Enable onboard eMMC on Radxa E20C
arm64: dts: rockchip: Add SDHCI controller for RK3528
arm64: dts: rockchip: Remove bluetooth node from rock-3a
arm64: dts: rockchip: Move rk356x scmi SHMEM to reserved memory
...
|
|
Whether the MII transmit clock can be stopped is primarily a property
of the PHY (there is a capability bit that should be checked first.)
Whether the MAC is capable of stopping the transmit clock is a separate
issue, but this is already handled by the core DesignWare MAC code.
As commit "net: stmmac: stm32: use PHY capability for TX clock stop"
adds the flag to use the PHY capability, remove the DT property that is
now unecessary.
Cc: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsIUA-005vGX-8A@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce the devicetree for the Plymovent AQM board
(stm32mp151c-plyaqm), based on the STM32MP151 SoC.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20250305131425.1491769-5-o.rempel@pengutronix.de
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add pinmux groups required for the Plymovent AQM board.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20250305131425.1491769-4-o.rempel@pengutronix.de
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
LDO2 is expansion connector supply on STM32MP13xx DHCOR DHSBC rev.200.
LDO5 is carrier board supply on STM32MP13xx DHCOR DHSBC rev.200. Keep
both regulators always enabled to make sure both the carrier board and
the expansion connector is always powered on and supplied with correct
voltage.
Describe ST33TPHF2XSPI TPM 2.0 chip interrupt and reset lines.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20250302152605.54792-1-marex@denx.de
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Replace the number 2 with the appropriate numerical constant defined in
dt-bindings/interrupt-controller/irq.h.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Antonio Borneo <antonio.borneo@foss.st.com>
Link: https://lore.kernel.org/r/20250310122402.8795-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
As indicated by the board silkscreen, there are three user LEDs.
Add the missing one.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250217114513.1098844-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Associate the LED node name with the corresponding board silkscreen for
more precise identification. In fact, the board has a total of seven
LEDs, some of which are user-controllable (i. e. usr{1,2,3}), while
others are directly controlled by hardware (e. g. power, overcurrent,
...). All these LEDs are either green or red, so using the names
led-green and led-red for the two LEDs mapped in the DTS does not
simplify their identification on the board.
Moreover, this patch is a prerequisite for adding the usr3 LED, which
has not been included in the DTS.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250217114513.1098844-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add node for user push button.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250217114332.1098482-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add node for the user led.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250217114332.1098482-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Introduce the devicetree for the Priva E-Measuringbox board
(stm32mp133c-prihmb), based on the STM32MP133 SoC.
Signed-off-by: Roan van Dijk <roan@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20250203085820.609176-5-o.rempel@pengutronix.de
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add thermal zone configuration and sensor node for STM32MP131 SoC.
Signed-off-by: Roan van Dijk <roan@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20250203085820.609176-4-o.rempel@pengutronix.de
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The Linux Automation GmbH FairyTux2 is a small Linux device based on
an Octavo Systems OSD32MP153c SiP, that occupies just two slots on a
DIN rail.
The device contains an eMMC for storage, a gigabit Ethernet
connection, a CAN bus and a RS485 transceiver.
Add support for the lxa-fairytux2 generation 1 and 2 boards based on
the STM32MP153c.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into soc/dt
Add and enable MALI400 support for STiH410-b2260
* tag 'sti-dt-for-v6.14-round1' of https://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: st: enable the MALI gpu on the stih410-b2260
ARM: dts: st: add node for the MALI gpu on stih410.dtsi
dt-bindings: gpu: mali-utgard: Add st,stih410-mali compatible
Link: https://lore.kernel.org/r/f44cb1f0-4d91-4e25-8b1f-3dd9a7bed62b@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable the GPU on the stih410-b2260 board.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add the entry for the GPU (Mali400) on the stih410.dtsi
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Swap USART3 and UART8 aliases on STM32MP15xx DHCOM SoM,
make sure UART8 is listed first, USART3 second, because
the UART8 is labeled as UART2 on the SoM pinout, while
USART3 is labeled as UART3 on the SoM pinout.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Enable the counter nodes without dedicated pins. With such configuration,
the counter interface can be used on internal clock to generate events.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Enable the counter nodes without dedicated pins. With such configuration,
the counter interface can be used on internal clock to generate events.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Enable the counter nodes without dedicated pins. With such configuration,
the counter interface can be used on internal clock to generate events.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Counter driver originally had support limited to quadrature interface
and simple counter. It has been improved[1], so add the remaining
stm32 timer counter nodes.
[1] https://lore.kernel.org/linux-arm-kernel/20240307133306.383045-1-fabrice.gasnier@foss.st.com/
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Counter driver originally had support limited to quadrature interface
and simple counter. It has been improved[1], so add the remaining
stm32 timer counter nodes.
[1] https://lore.kernel.org/linux-arm-kernel/20240307133306.383045-1-fabrice.gasnier@foss.st.com/
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add support for the lxa-tac generation 3 board based on the
STM32MP153c.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
This is a preparation patch in order to add lxa-tac generation 3
board.
As the gen3 board has a different adc and gpio{e,g} setups, move these
from the stm32mp15xc-lxa-tac.dtsi to the gen{1,2}.dts files.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Allow providing the Ethernet and mass storage functions on the USB
peripheral port at the same time.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Some of the userspace software and tests depend on the can/i2c/spi
devices having the same name on every boot. This may not always be the
case based on e.g. parallel probe order.
Assign static device numbers to all can/i2c/spi devices.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The RTC was enabled under the false assumption that the SoM already
contains a suitable 32.768 kHz crystal.
It does however not contain such a crystal and since none is fitted
externally to the SoM the RTC can not be used on the hardware.
Reflect that in the devicetree.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The GIC IRQ type used for IPCC RX should be IRQ_TYPE_LEVEL_HIGH.
Replacing the interrupt with the EXTI event changes the type to
the numeric value 1, meaning IRQ_TYPE_EDGE_RISING.
The issue is that EXTI event 61 is a direct event.The IRQ type of
direct events is not used by EXTI and is propagated to the parent
IRQ controller of EXTI, the GIC.
Align the IRQ type to the value expected by the GIC by replacing
the second parameter "1" with IRQ_TYPE_LEVEL_HIGH.
Fixes: 7d9802bb0e34 ("ARM: dts: stm32: remove the IPCC "wakeup" IRQ on stm32mp151")
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Move the M24256E write-lockable page subnode after RTC subnode in
DH STM32MP13xx DHCOR SoM DT to keep the list of nodes sorted by I2C
address. No functional change.
Fixes: 3f2e7d167307 ("ARM: dts: stm32: Describe M24256E write-lockable page in DH STM32MP13xx DHCOR SoM DT")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The STM32MP13xx DHCOR DHSBC is populated with STM32MP13xx part capable
of 1 GHz operation, increase the CPU core voltage to 1.35 V to make
sure the SoC is stable even if the blobs unconditionally force the CPU
to 1 GHz operation.
It is not possible to make use of CPUfreq on the STM32MP13xx because
the SCMI protocol 0x13 is not implemented by upstream OpTee-OS which
is the SCMI provider.
Fixes: 6331bddce649 ("ARM: dts: stm32: Add support for STM32MP13xx DHCOR SoM and DHSBC board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
