| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull new SoC support from Arnd Bergmann:
"These five newly supported chips come with both devicetree
descriptions and the changes to wire them up to the build system for
easier bisection.
The chips in question are:
- Marvell PXA1908 was the first 64-bit mobile phone chip from Marvell
in the product line that started with the Digital StrongARM SA1100
based PDAs and continued with the Intel PXA2xx that dominated early
smartphones. This one only made it only into a few products before
the entire product line was cut in 2015.
- The QiLai SoC is made by RISC-V core designer Andes Technologies
and is in the 'Voyager' reference board in MicroATX form factor. It
uses four in-order AX45MP cores, which is the midrange product from
Andes.
- CIX P1 is one of the few Arm chips designed for small workstations,
and this one uses 12 Cortex-A720/A520 cores, making it also one of
the only ARMv9.2 machines that one can but at the moment.
- Axiado AX3000 is an embedded chip with relative small Cortex-A53
CPU cores described as a "Trusted Control/Compute Unit" that can be
used as a BMC in servers. In addition to the usual I/O, this one
comes with 10GBit ethernet and and a 4TOPS NPU.
- Sophgo SG2000 is an embedded chip that comes with both RISC-V and
Arm cores that can run Linux. This was already supported for RISC-V
but now it also works on Arm
One more chip, the Black Sesame C1200 did not make it in tirm for the
merge window"
* tag 'soc-newsoc-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
arm64: defconfig: Enable rudimentary Sophgo SG2000 support
arm64: Add SOPHGO SOC family Kconfig support
arm64: dts: sophgo: Add Duo Module 01 Evaluation Board
arm64: dts: sophgo: Add Duo Module 01
arm64: dts: sophgo: Add initial SG2000 SoC device tree
MAINTAINERS: Add entry for Axiado
arm64: defconfig: enable the Axiado family
arm64: dts: axiado: Add initial support for AX3000 SoC and eval board
arm64: add Axiado SoC family
dt-bindings: i3c: cdns: add Axiado AX3000 I3C controller
dt-bindings: serial: cdns: add Axiado AX3000 UART controller
dt-bindings: gpio: cdns: add Axiado AX3000 GPIO variant
dt-bindings: gpio: cdns: convert to YAML
dt-bindings: arm: axiado: add AX3000 EVK compatible strings
dt-bindings: vendor-prefixes: Add Axiado Corporation
MAINTAINERS: Add CIX SoC maintainer entry
arm64: dts: cix: Add sky1 base dts initial support
dt-bindings: clock: cix: Add CIX sky1 scmi clock id
arm64: defconfig: Enable CIX SoC
mailbox: add CIX mailbox driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into gpio/for-next
Immutable branch between MFD, GPIO, Power and SoC due for the v6.17 merge window
|
|
The GPIO controllers in most Rockchip SoCs are part of power domains
that are always powered on, i.e. PD_BUS or PD_PMU. These always powered
on power domains have typically not been described in the device tree.
Because these power domains have been left out of the device tree there
has not been any real need to properly describe the GPIO controllers
power domain.
On RK3528 the GPIO controllers are spread out among the described
PD_RKVENC, PD_VO and PD_VPU power domains. However, one GPIO controller
belong to an undescribed always powered on power domain.
Add support to describe an optional power-domains for the GPIO
controllers in Rockchip SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250723085654.2273324-2-jonas@kwiboo.se
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Add the DT binding for the Apple Mac System Management Controller GPIOs.
Signed-off-by: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Signed-off-by: Sven Peter <sven@kernel.org>
Link: https://lore.kernel.org/r/20250610-smc-6-15-v7-1-556cafd771d3@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add binding for Axiado AX3000 GPIO controller. So far, no changes
are known, so it can fallback to default compatible.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Harshit Shah <hshah@axiado.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Convert Cadence family GPIO controller bindings to DT schema.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Harshit Shah <hshah@axiado.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Convert the Qualcomm Atheros AR7xxx/AR9xxx GPIO binding to DT schema
format.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250714202859.3012173-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the Maxim MAX3191x and similar GPIO binding to DT schema format.
It's a straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20250714202843.3011698-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The fsl,mpc8349-gpio, fsl,mpc8572-gpio, and fsl,mpc8610-gpio compatibles
are already documented in fsl,qoriq-gpio.yaml. Add the additional
compatibles that use fsl,mpc8349-gpio as a fallback. With that,
the 8xxx_gpio.txt binding document is redundant and can be removed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20250714202941.3013390-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Many simple GPIO controllers without interrupt capability have the same
schema other than their compatible value. Combine all these bindings
into a single schema. The criteria to be included here is must use 2
cells, have no interrupt capability, have 0 or 1 "reg" entries, and
have no other resources (like clocks).
Note that "ngpios" is now allowed in some cases it wasn't before and
constraints on it have been dropped.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250714201959.2983482-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the ST SPEAr SPI CS GPIO binding to DT schema format. It's a
straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20250714202753.3010240-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the Abilis TB10x GPIO binding to DT schema format. It's a
straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250714202934.3013189-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert APM X-Gene Standby GPIO binding to DT schema format. It's a
straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250714202821.3011099-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the TI TWL4030 PMIC GPIO binding to DT schema format. The number
of #interrupt-cells was wrong compared to what is in use. Correct it to
be 1.
Reviewed-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250714202829.3011298-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the Lantiq SoC External Bus memory mapped GPIO binding to DT
schema format. It's a straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250714202837.3011521-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the TI Keystone DSP GPIO binding to DT schema format. The
"ti,syscon-dev" property was wrong and should be "gpio,syscon-dev"
instead.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250714202850.3011952-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the altr,pio-1.0 binding to DT schema format. It's a
straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250714202905.3012386-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the cirrus,clps711x-mctrl-gpio binding to DT schema format.
Add the missing "gpio,syscon-dev" phandle property.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250714202919.3012764-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the Cavium Octeon 3860 GPIO binding to DT schema format. It's a
straight forward conversion.
Looks like Octeon has no maintainers, so Bartosz is listed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250714202927.3012974-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert XRA1403 16-bit GPIO Expander binding to DT schema format. It's a
straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250714202813.3010879-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the Microchip PIC32 GPIO binding to DT schema format. It's a
straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250714202807.3010652-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the Lacie NetxBig GPIO binding to DT schema format. It's a
straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250714202801.3010442-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The TCA6418E is a 18-channel I2C I/O expander with integrated ESD
protection.
Signed-off-by: Maria Garcia <mariagarcia7293@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250703205740.45385-2-mariagarcia7293@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
It is possible that the PL061 doesn't have any interrupt connected and
can't be an interrupt provider, so drop the interrupt properties as
required.
The LG LG131x SoCs are one example of this.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250609220900.3035642-1-robh@kernel.org
[Bartosz: g/pl011/pl061/]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
On Microblaze platforms there is no need to handle clocks because the
system is starting with clocks enabled (can be described via fixed clock
node or clock-frequency property or not described at all).
With using soft IPs with SOC platforms there is mandatory to handle clocks
as is explained in commit 60dbdc6e08d6 ("dt-bindings: net: emaclite: Add
clock support").
That's why make clock as required in dt binding because it is present in
both configurations and should be described even there is no way how to
handle it on Microblaze systems.
There is also need to describe missing axi gpio clock in fpga-region.yaml
not to introduce new error when make dt_binding_check runs.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Xu Yilun <yilun.xu@intel.com> # fpga
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/94151cfbcff5e4ae05894981c7e398b605d4b00a.1750059796.git.michal.simek@amd.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert nxp,lpc1850-gpio.txt to yaml format.
Additional changes:
- remove interrupt-controller and #interupt-cells from required list to
match existed dts files.
- remove gpio consumer in examples.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250602144259.944257-1-Frank.Li@nxp.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert gpio-74xx-mmio.txt to yaml format.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250604144631.1141430-1-Frank.Li@nxp.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Covert gpio-pisosr.txt to yaml format.
Additional changes:
- Add ref to spi-peripheral-props.yaml.
- Set ngpios max value to 32.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250522223742.516254-1-Frank.Li@nxp.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have three new drivers, some refactoring in the GPIO core, lots of
various changes across many drivers, new configfs interface for the
virtual gpio-aggregator module and DT-bindings updates.
The treewide conversion of GPIO drivers to using the new value setter
callbacks is ongoing with another round of GPIO drivers updated. You
will also see these commits coming in from other subsystems as with
the relevant changes merged into mainline last cycle, I've started
converting GPIO providers located elsewhere than drivers/gpio/.
GPIO core:
- use more lock guards where applicable
- refactor GPIO ACPI code and shrink it in the process by 8%
- move GPIO ACPI quirks into a separate file
- remove unneeded #ifdef
- convert GPIO devres helpers to using devm_add_action() where
applicable which shrinks and simplifies the code
- refactor GPIO descriptor validation in GPIO consumer interfaces
- don't allow setting values on input lines in the GPIO core which
will take off the burden from GPIO drivers of checking this down
the line
- provide gpiod_is_equal() as a way of safely comparing two GPIO
descriptors (the only current user is in regulator core)
New drivers:
- add the GPIO module for the max77759 multifunction device
- add the GPIO driver for the VeriSilicon BLZP1600 GPIO controller
- add the GPIO driver for the Spacemit K1 SoC
Driver improvements:
- convert more drivers to using the new GPIO line value setter
callbacks
- convert more drivers to making the irq_chip immutable as is
recommended by the interrupt subsystem
- extend build testing coverage by enabling more modules to be built
with COMPILE_TEST=y
- extend the gpio-aggregator module with a configfs interface that
makes the setup easier for user-space than the existing
driver-level sysfs attributes and also adds more advanced
configuration features (such as referring to aggregated lines by
their original names or modifying their names as exposed by the
aggregated chip)
- add a missing mutex_destroy() in gpio-imx-scu
- add an OF polarity quirk for s5m8767
- allow building gpio-vf610 as a loadable module
- make gpio-mxc not hardcode its GPIO base number with GPIO SYSFS
interface disabled (another small step towards getting rid of the
global GPIO numberspace)
- add support for level-triggered interrupts to gpio-pca953x
- don't double-check the ngpios property in gpio-ds4520 as GPIO core
already does it
- don't double-check the number of GPIOs in gpio-imx-scu as GPIO core
already does it
- remove unused callbacks from gpio-max3191x
DT bindings:
- add device-tree bindings for max77759, spacemit,k1 and blzp1600
(new drivers added this cycle)
- document more properties for gpio-vf610 and gpio-tegra186
- document a new pca95xx variant
- fix style of examples in several GPIO DT-binding documents
Misc:
- TODO list updates"
* tag 'gpio-updates-for-v6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (123 commits)
gpio: timberdale: select GPIOLIB_IRQCHIP
gpio: lpc18xx: select GPIOLIB_IRQCHIP
gpio: grgpio: select GPIOLIB_IRQCHIP
gpio: bcm-kona: select GPIOLIB_IRQCHIP
dt-bindings: gpio: vf610: add ngpios and gpio-reserved-ranges
gpio: davinci: select GPIOLIB_IRQCHIP
gpiolib-acpi: Update file references in the Documentation and MAINTAINERS
gpiolib: acpi: Move quirks to a separate file
gpiolib: acpi: Add acpi_gpio_need_run_edge_events_on_boot() getter
gpiolib: acpi: Handle deferred list via new API
gpiolib: acpi: Make sure we fill struct acpi_gpio_info
gpiolib: acpi: Switch to use enum in acpi_gpio_in_ignore_list()
gpiolib: acpi: Use temporary variable for struct acpi_gpio_info
gpiolib: remove unneeded #ifdef
gpio: mpc8xxx: select GPIOLIB_IRQCHIP
gpio: pxa: select GPIOLIB_IRQCHIP
gpio: pxa: Make irq_chip immutable
gpio: timberdale: Make irq_chip immutable
gpio: xgene-sb: Make irq_chip immutable
gpio: davinci: Make irq_chip immutable
...
|
|
Add optional ngpios and gpio-reserved-ranges property.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250520-gpio-dts-v3-1-04771c6cf325@nxp.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Add optional gpio-ranges property.
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250429-tegra186-pinctrl-v1-2-722c7c42394e@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into gpio/for-next
Immutable branch between MFD, GPIO and NVMEM due for the v6.16 merge window
|
|
The Maxim MAX77759 is a companion PMIC for USB Type-C applications and
includes Battery Charger, Fuel Gauge, temperature sensors, USB Type-C
Port Controller (TCPC), NVMEM, and a GPIO expander.
This describes its GPIO module.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250325-max77759-mfd-v6-1-c0870ca662ba@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The GPIO controller of K1 support basic functions as input/output,
all pins can be used as interrupt which route to one IRQ line,
trigger type can be select between rising edge, falling edge, or both.
There are four GPIO banks, each consisting of 32 pins.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Link: https://lore.kernel.org/r/20250412-03-k1-gpio-v8-1-1c6862d272ec@gentoo.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
As I am leaving AMD and will no longer be maintaining
these platform drivers, so removing myself from maintainership.
Signed-off-by: Mubin Sayyed <mubin.sayyed@amd.com>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250403060836.2602361-1-mubin.sayyed@amd.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
This is a custom silicon GPIO driver provided by VeriSilicon
Microelectronics. It has 32 input/output ports which can be
configured as edge or level triggered interrupts. It also provides
a de-bounce feature.
This controller is used on the Blaize BLZP1600 SoC.
Signed-off-by: Nikolaos Pasaloukos <nikolaos.pasaloukos@blaize.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250327-kernel-upstreaming-add_gpio_support-v2-1-bbe51f8d66da@blaize.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The Toradex ecgpiol16 is a 16-bit I2C I/O expander implemented using a
small MCU.
Its register interface and behavior are compatible with the PCAL6416.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250331072644.17921-1-francesco@dolcini.it
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
DTS example in the bindings should be indented with 2- or 4-spaces and
aligned with opening '- |', so correct any differences like 3-spaces or
mixtures 2- and 4-spaces in one binding. While re-indenting, drop
unused labels.
No functional changes here, but saves some comments during reviews of
new patches built on existing code.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250324125326.82270-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Add compatible string "fsl,imx94-gpio" for the i.MX94 chip, which is
backward compatible with i.MX8ULP. Set it to fall back to
"fsl,imx8ulp-gpio".
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250306170921.241690-1-Frank.Li@nxp.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Add the devicetree compatibles for Loongson-7A2000 and Loongson-3A6000
gpio chip.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20250303074552.3335186-1-zhoubinbin@loongson.cn
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The Marvell mvebu binding users already use 'gpio-ranges' and have hog
nodes, so add them to the binding.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250227175132.3734524-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
A few of the I2C GPIO expander chips supported by this binding have a
RESETN pin to be able to reset the chip. The chip is held in reset while
the pin is low, therefore the polarity of reset-gpios is expected to
reflect that, i.e. a GPIO_ACTIVE_HIGH means the GPIO will be driven high
for reset and then driven low, GPIO_ACTIVE_LOW means the GPIO will be
driven low for reset and then driven high. If a GPIO is directly routed
to RESETN pin on the IC without any inverter, GPIO_ACTIVE_LOW is thus
expected.
Out of the supported chips, only PCA9670, PCA9671, PCA9672 and PCA9673
show a RESETN pin in their datasheets. They all share the same reset
timings, that is 4+us reset pulse[0] and 100+us reset time[0].
When performing a reset, "The PCA9670 registers and I2C-bus state
machine will be held in their default state until the RESET input is
once again HIGH."[1] meaning we now know the state of each line
controlled by the GPIO expander. Therefore, setting lines-initial-states
and reset-gpios both does not make sense and their presence is XOR'ed.
[0] https://www.nxp.com/docs/en/data-sheet/PCA9670.pdf Fig 22.
[1] https://www.nxp.com/docs/en/data-sheet/PCA9670.pdf 8.5
Tested-by: Heiko Stuebner <heiko@sntech.de> # exclusion logic
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250224-pca976x-reset-driver-v3-1-58370ef405be@cherry.de
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Allow parsing GPIO controller children nodes with GPIO hogs.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://lore.kernel.org/r/20250204194115.3899174-3-ninad@linux.ibm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
This is for the MPC831{4,5}{,E} SoCs.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250102-mpc83xx-v1-11-86f78ba2a7af@posteo.net
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
From looking at the data sheets, it is not obvious that CS# and latch
clock can be treated at the same, but doing so works fine and saves the
hassle of (1) trying to specify a SPI device without CS, and (2) adding
another property to drive the latch clock[1].
[1]: https://lore.kernel.org/lkml/20241213-gpio74-v1-2-fa2c089caf41@posteo.net/
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241224-gpio74-v2-3-bbcf14183191@posteo.net
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
gpio-line-names is a generic property that can be supported by any
GPIO controller, so permit it through the binding.
It is permitted to have a variable number of GPIOs per node based
on brcm,gpio-bank-widths, so define an arbitrary maximum number of
items based on current users.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241212-dt-bcm2712-fixes-v3-3-44a7f3390331@raspberrypi.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
This adds the ngpios property to MMIO GPIO. We restrict the
property to 1..63 since there is no point in 0 GPIO lines and
we support up to 64bits wide registers for now.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241017-gpio-ngpios-v2-1-cecfdb38d40e@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The AST2700 is the 7th generation SoC from Aspeed, featuring two GPIO
controllers: one with 12 GPIO pins and another with 216 GPIO pins.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20241008081450.1490955-7-billy_tsai@aspeedtech.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Enabling dtc interrupt_provider check reveals the example is missing the
"#interrupt-cells" property as it is a dependency of
"interrupt-controller".
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240925173504.1906872-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC update from Arnd Bergmann:
"Convert ep93xx to devicetree
This concludes a long journey towards replacing the old board files
with devictree description on the Cirrus Logic EP93xx platform.
Nikita Shubin has been working on this for a long time, for details
see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/"
* tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
dt-bindings: gpio: ep9301: Add missing "#interrupt-cells" to examples
MAINTAINERS: Update EP93XX ARM ARCHITECTURE maintainer
soc: ep93xx: drop reference to removed EP93XX_SOC_COMMON config
net: cirrus: use u8 for addr to calm down sparse
dmaengine: cirrus: use snprintf() to calm down gcc 13.3.0
dmaengine: ep93xx: Fix a NULL vs IS_ERR() check in probe()
pinctrl: ep93xx: Fix raster pins typo
spi: ep93xx: update kerneldoc comments for ep93xx_spi
clk: ep93xx: Fix off by one in ep93xx_div_recalc_rate()
clk: ep93xx: add module license
dmaengine: cirrus: remove platform code
ASoC: cirrus: edb93xx: Delete driver
ARM: ep93xx: soc: drop defines
ARM: ep93xx: delete all boardfiles
ata: pata_ep93xx: remove legacy pinctrl use
pwm: ep93xx: drop legacy pinctrl
ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
ARM: dts: ep93xx: Add EDB9302 DT
ARM: dts: ep93xx: add ts7250 board
ARM: dts: add Cirrus EP93XX SoC .dtsi
...
|
