Add bridged amplifiers to cs42l43

Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>:

In some cs42l43 systems a couple of cs35l56 amplifiers are attached
to the cs42l43's SPI and I2S. On Windows the cs42l43 is controlled
by a SDCA class driver and these two amplifiers are controlled by
firmware running on the cs42l43. However, under Linux the decision
was made to interact with the cs42l43 directly, affording the user
greater control over the audio system. However, this has resulted
in an issue where these two bridged cs35l56 amplifiers are not
populated in ACPI and must be added manually. There is at least an
SDCA extension unit DT entry we can key off.

The process of adding this is handled using a software node, firstly the
ability to add native chip selects to software nodes must be added.
Secondly, an additional flag for naming the SPI devices is added this
allows the machine driver to key to the correct amplifier. Then finally,
the cs42l43 SPI driver adds the two amplifiers directly onto its SPI
bus.

An additional series will follow soon to add the audio machine driver
parts (in the sof-sdw driver), however that is fairly orthogonal to
this part of the process, getting the actual amplifiers registered.

1 files changed, 113 insertions, 69 deletions

diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 5e329156d1bae..93544f1cc2a51 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -107,6 +107,16 @@ s32 e1000e_phy_reset_dsp(struct e1000_hw *hw)
 	return e1e_wphy(hw, M88E1000_PHY_GEN_CONTROL, 0);
 }
 
+void e1000e_disable_phy_retry(struct e1000_hw *hw)
+{
+	hw->phy.retry_enabled = false;
+}
+
+void e1000e_enable_phy_retry(struct e1000_hw *hw)
+{
+	hw->phy.retry_enabled = true;
+}
+
 /**
  *  e1000e_read_phy_reg_mdic - Read MDI control register
  *  @hw: pointer to the HW structure
@@ -118,55 +128,73 @@ s32 e1000e_phy_reset_dsp(struct e1000_hw *hw)
  **/
 s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
 {
+	u32 i, mdic = 0, retry_counter, retry_max;
 	struct e1000_phy_info *phy = &hw->phy;
-	u32 i, mdic = 0;
+	bool success;
 
 	if (offset > MAX_PHY_REG_ADDRESS) {
 		e_dbg("PHY Address %d is out of range\n", offset);
 		return -E1000_ERR_PARAM;
 	}
 
+	retry_max = phy->retry_enabled ? phy->retry_count : 0;
+
 	/* Set up Op-code, Phy Address, and register offset in the MDI
 	 * Control register.  The MAC will take care of interfacing with the
 	 * PHY to retrieve the desired data.
 	 */
-	mdic = ((offset << E1000_MDIC_REG_SHIFT) |
-		(phy->addr << E1000_MDIC_PHY_SHIFT) |
-		(E1000_MDIC_OP_READ));
+	for (retry_counter = 0; retry_counter <= retry_max; retry_counter++) {
+		success = true;
 
-	ew32(MDIC, mdic);
+		mdic = ((offset << E1000_MDIC_REG_SHIFT) |
+			(phy->addr << E1000_MDIC_PHY_SHIFT) |
+			(E1000_MDIC_OP_READ));
 
-	/* Poll the ready bit to see if the MDI read completed
-	 * Increasing the time out as testing showed failures with
-	 * the lower time out
-	 */
-	for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
-		udelay(50);
-		mdic = er32(MDIC);
-		if (mdic & E1000_MDIC_READY)
-			break;
-	}
-	if (!(mdic & E1000_MDIC_READY)) {
-		e_dbg("MDI Read PHY Reg Address %d did not complete\n", offset);
-		return -E1000_ERR_PHY;
-	}
-	if (mdic & E1000_MDIC_ERROR) {
-		e_dbg("MDI Read PHY Reg Address %d Error\n", offset);
-		return -E1000_ERR_PHY;
-	}
-	if (FIELD_GET(E1000_MDIC_REG_MASK, mdic) != offset) {
-		e_dbg("MDI Read offset error - requested %d, returned %d\n",
-		      offset, FIELD_GET(E1000_MDIC_REG_MASK, mdic));
-		return -E1000_ERR_PHY;
+		ew32(MDIC, mdic);
+
+		/* Poll the ready bit to see if the MDI read completed
+		 * Increasing the time out as testing showed failures with
+		 * the lower time out
+		 */
+		for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
+			usleep_range(50, 60);
+			mdic = er32(MDIC);
+			if (mdic & E1000_MDIC_READY)
+				break;
+		}
+		if (!(mdic & E1000_MDIC_READY)) {
+			e_dbg("MDI Read PHY Reg Address %d did not complete\n",
+			      offset);
+			success = false;
+		}
+		if (mdic & E1000_MDIC_ERROR) {
+			e_dbg("MDI Read PHY Reg Address %d Error\n", offset);
+			success = false;
+		}
+		if (FIELD_GET(E1000_MDIC_REG_MASK, mdic) != offset) {
+			e_dbg("MDI Read offset error - requested %d, returned %d\n",
+			      offset, FIELD_GET(E1000_MDIC_REG_MASK, mdic));
+			success = false;
+		}
+
+		/* Allow some time after each MDIC transaction to avoid
+		 * reading duplicate data in the next MDIC transaction.
+		 */
+		if (hw->mac.type == e1000_pch2lan)
+			usleep_range(100, 150);
+
+		if (success) {
+			*data = (u16)mdic;
+			return 0;
+		}
+
+		if (retry_counter != retry_max) {
+			e_dbg("Perform retry on PHY transaction...\n");
+			mdelay(10);
+		}
 	}
-	*data = (u16)mdic;
 
-	/* Allow some time after each MDIC transaction to avoid
-	 * reading duplicate data in the next MDIC transaction.
-	 */
-	if (hw->mac.type == e1000_pch2lan)
-		udelay(100);
-	return 0;
+	return -E1000_ERR_PHY;
 }
 
 /**
@@ -179,56 +207,72 @@ s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
  **/
 s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
 {
+	u32 i, mdic = 0, retry_counter, retry_max;
 	struct e1000_phy_info *phy = &hw->phy;
-	u32 i, mdic = 0;
+	bool success;
 
 	if (offset > MAX_PHY_REG_ADDRESS) {
 		e_dbg("PHY Address %d is out of range\n", offset);
 		return -E1000_ERR_PARAM;
 	}
 
+	retry_max = phy->retry_enabled ? phy->retry_count : 0;
+
 	/* Set up Op-code, Phy Address, and register offset in the MDI
 	 * Control register.  The MAC will take care of interfacing with the
 	 * PHY to retrieve the desired data.
 	 */
-	mdic = (((u32)data) |
-		(offset << E1000_MDIC_REG_SHIFT) |
-		(phy->addr << E1000_MDIC_PHY_SHIFT) |
-		(E1000_MDIC_OP_WRITE));
+	for (retry_counter = 0; retry_counter <= retry_max; retry_counter++) {
+		success = true;
 
-	ew32(MDIC, mdic);
+		mdic = (((u32)data) |
+			(offset << E1000_MDIC_REG_SHIFT) |
+			(phy->addr << E1000_MDIC_PHY_SHIFT) |
+			(E1000_MDIC_OP_WRITE));
 
-	/* Poll the ready bit to see if the MDI read completed
-	 * Increasing the time out as testing showed failures with
-	 * the lower time out
-	 */
-	for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
-		udelay(50);
-		mdic = er32(MDIC);
-		if (mdic & E1000_MDIC_READY)
-			break;
-	}
-	if (!(mdic & E1000_MDIC_READY)) {
-		e_dbg("MDI Write PHY Reg Address %d did not complete\n", offset);
-		return -E1000_ERR_PHY;
-	}
-	if (mdic & E1000_MDIC_ERROR) {
-		e_dbg("MDI Write PHY Red Address %d Error\n", offset);
-		return -E1000_ERR_PHY;
-	}
-	if (FIELD_GET(E1000_MDIC_REG_MASK, mdic) != offset) {
-		e_dbg("MDI Write offset error - requested %d, returned %d\n",
-		      offset, FIELD_GET(E1000_MDIC_REG_MASK, mdic));
-		return -E1000_ERR_PHY;
-	}
+		ew32(MDIC, mdic);
 
-	/* Allow some time after each MDIC transaction to avoid
-	 * reading duplicate data in the next MDIC transaction.
-	 */
-	if (hw->mac.type == e1000_pch2lan)
-		udelay(100);
+		/* Poll the ready bit to see if the MDI read completed
+		 * Increasing the time out as testing showed failures with
+		 * the lower time out
+		 */
+		for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
+			usleep_range(50, 60);
+			mdic = er32(MDIC);
+			if (mdic & E1000_MDIC_READY)
+				break;
+		}
+		if (!(mdic & E1000_MDIC_READY)) {
+			e_dbg("MDI Write PHY Reg Address %d did not complete\n",
+			      offset);
+			success = false;
+		}
+		if (mdic & E1000_MDIC_ERROR) {
+			e_dbg("MDI Write PHY Reg Address %d Error\n", offset);
+			success = false;
+		}
+		if (FIELD_GET(E1000_MDIC_REG_MASK, mdic) != offset) {
+			e_dbg("MDI Write offset error - requested %d, returned %d\n",
+			      offset, FIELD_GET(E1000_MDIC_REG_MASK, mdic));
+			success = false;
+		}
 
-	return 0;
+		/* Allow some time after each MDIC transaction to avoid
+		 * reading duplicate data in the next MDIC transaction.
+		 */
+		if (hw->mac.type == e1000_pch2lan)
+			usleep_range(100, 150);
+
+		if (success)
+			return 0;
+
+		if (retry_counter != retry_max) {
+			e_dbg("Perform retry on PHY transaction...\n");
+			mdelay(10);
+		}
+	}
+
+	return -E1000_ERR_PHY;
 }
 
 /**