Merge tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from Jakub Kicinski:
 "Core & protocols:

   - Wrap datapath globals into net_aligned_data, to avoid false sharing

   - Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container)

   - Add SO_INQ and SCM_INQ support to AF_UNIX

   - Add SIOCINQ support to AF_VSOCK

   - Add TCP_MAXSEG sockopt to MPTCP

   - Add IPv6 force_forwarding sysctl to enable forwarding per interface

   - Make TCP validation of whether packet fully fits in the receive
     window and the rcv_buf more strict. With increased use of HW
     aggregation a single "packet" can be multiple 100s of kB

   - Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
     improves latency up to 33% for sockmap users

   - Convert TCP send queue handling from tasklet to BH workque

   - Improve BPF iteration over TCP sockets to see each socket exactly
     once

   - Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code

   - Support enabling kernel threads for NAPI processing on per-NAPI
     instance basis rather than a whole device. Fully stop the kernel
     NAPI thread when threaded NAPI gets disabled. Previously thread
     would stick around until ifdown due to tricky synchronization

   - Allow multicast routing to take effect on locally-generated packets

   - Add output interface argument for End.X in segment routing

   - MCTP: add support for gateway routing, improve bind() handling

   - Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink

   - Add a new neighbor flag ("extern_valid"), which cedes refresh
     responsibilities to userspace. This is needed for EVPN multi-homing
     where a neighbor entry for a multi-homed host needs to be synced
     across all the VTEPs among which the host is multi-homed

   - Support NUD_PERMANENT for proxy neighbor entries

   - Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM

   - Add sequence numbers to netconsole messages. Unregister
     netconsole's console when all net targets are removed. Code
     refactoring. Add a number of selftests

   - Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
     should be used for an inbound SA lookup

   - Support inspecting ref_tracker state via DebugFS

   - Don't force bonding advertisement frames tx to ~333 ms boundaries.
     Add broadcast_neighbor option to send ARP/ND on all bonded links

   - Allow providing upcall pid for the 'execute' command in openvswitch

   - Remove DCCP support from Netfilter's conntrack

   - Disallow multiple packet duplications in the queuing layer

   - Prevent use of deprecated iptables code on PREEMPT_RT

  Driver API:

   - Support RSS and hashing configuration over ethtool Netlink

   - Add dedicated ethtool callbacks for getting and setting hashing
     fields

   - Add support for power budget evaluation strategy in PSE /
     Power-over-Ethernet. Generate Netlink events for overcurrent etc

   - Support DPLL phase offset monitoring across all device inputs.
     Support providing clock reference and SYNC over separate DPLL
     inputs

   - Support traffic classes in devlink rate API for bandwidth
     management

   - Remove rtnl_lock dependency from UDP tunnel port configuration

  Device drivers:

   - Add a new Broadcom driver for 800G Ethernet (bnge)

   - Add a standalone driver for Microchip ZL3073x DPLL

   - Remove IBM's NETIUCV device driver

   - Ethernet high-speed NICs:
      - Broadcom (bnxt):
         - support zero-copy Tx of DMABUF memory
         - take page size into account for page pool recycling rings
      - Intel (100G, ice, idpf):
         - idpf: XDP and AF_XDP support preparations
         - idpf: add flow steering
         - add link_down_events statistic
         - clean up the TSPLL code
         - preparations for live VM migration
      - nVidia/Mellanox:
         - support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
         - optimize context memory usage for matchers
         - expose serial numbers in devlink info
         - support PCIe congestion metrics
      - Meta (fbnic):
         - add 25G, 50G, and 100G link modes to phylink
         - support dumping FW logs
      - Marvell/Cavium:
         - support for CN20K generation of the Octeon chips
      - Amazon:
         - add HW clock (without timestamping, just hypervisor time access)

   - Ethernet virtual:
      - VirtIO net:
         - support segmentation of UDP-tunnel-encapsulated packets
      - Google (gve):
         - support packet timestamping and clock synchronization
      - Microsoft vNIC:
         - add handler for device-originated servicing events
         - allow dynamic MSI-X vector allocation
         - support Tx bandwidth clamping

   - Ethernet NICs consumer, and embedded:
      - AMD:
         - amd-xgbe: hardware timestamping and PTP clock support
      - Broadcom integrated MACs (bcmgenet, bcmasp):
         - use napi_complete_done() return value to support NAPI polling
         - add support for re-starting auto-negotiation
      - Broadcom switches (b53):
         - support BCM5325 switches
         - add bcm63xx EPHY power control
      - Synopsys (stmmac):
         - lots of code refactoring and cleanups
      - TI:
         - icssg-prueth: read firmware-names from device tree
         - icssg: PRP offload support
      - Microchip:
         - lan78xx: convert to PHYLINK for improved PHY and MAC management
         - ksz: add KSZ8463 switch support
      - Intel:
         - support similar queue priority scheme in multi-queue and
           time-sensitive networking (taprio)
         - support packet pre-emption in both
      - RealTek (r8169):
         - enable EEE at 5Gbps on RTL8126
      - Airoha:
         - add PPPoE offload support
         - MDIO bus controller for Airoha AN7583

   - Ethernet PHYs:
      - support for the IPQ5018 internal GE PHY
      - micrel KSZ9477 switch-integrated PHYs:
         - add MDI/MDI-X control support
         - add RX error counters
         - add cable test support
         - add Signal Quality Indicator (SQI) reporting
      - dp83tg720: improve reset handling and reduce link recovery time
      - support bcm54811 (and its MII-Lite interface type)
      - air_en8811h: support resume/suspend
      - support PHY counters for QCA807x and QCA808x
      - support WoL for QCA807x

   - CAN drivers:
      - rcar_canfd: support for Transceiver Delay Compensation
      - kvaser: report FW versions via devlink dev info

   - WiFi:
      - extended regulatory info support (6 GHz)
      - add statistics and beacon monitor for Multi-Link Operation (MLO)
      - support S1G aggregation, improve S1G support
      - add Radio Measurement action fields
      - support per-radio RTS threshold
      - some work around how FIPS affects wifi, which was wrong (RC4 is
        used by TKIP, not only WEP)
      - improvements for unsolicited probe response handling

   - WiFi drivers:
      - RealTek (rtw88):
         - IBSS mode for SDIO devices
      - RealTek (rtw89):
         - BT coexistence for MLO/WiFi7
         - concurrent station + P2P support
         - support for USB devices RTL8851BU/RTL8852BU
      - Intel (iwlwifi):
         - use embedded PNVM in (to be released) FW images to fix
           compatibility issues
         - many cleanups (unused FW APIs, PCIe code, WoWLAN)
         - some FIPS interoperability
      - MediaTek (mt76):
         - firmware recovery improvements
         - more MLO work
      - Qualcomm/Atheros (ath12k):
         - fix scan on multi-radio devices
         - more EHT/Wi-Fi 7 features
         - encapsulation/decapsulation offload
      - Broadcom (brcm80211):
         - support SDIO 43751 device

   - Bluetooth:
      - hci_event: add support for handling LE BIG Sync Lost event
      - ISO: add socket option to report packet seqnum via CMSG
      - ISO: support SCM_TIMESTAMPING for ISO TS

   - Bluetooth drivers:
      - intel_pcie: support Function Level Reset
      - nxpuart: add support for 4M baudrate
      - nxpuart: implement powerup sequence, reset, FW dump, and FW loading"

* tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1742 commits)
  dpll: zl3073x: Fix build failure
  selftests: bpf: fix legacy netfilter options
  ipv6: annotate data-races around rt->fib6_nsiblings
  ipv6: fix possible infinite loop in fib6_info_uses_dev()
  ipv6: prevent infinite loop in rt6_nlmsg_size()
  ipv6: add a retry logic in net6_rt_notify()
  vrf: Drop existing dst reference in vrf_ip6_input_dst
  net/sched: taprio: align entry index attr validation with mqprio
  net: fsl_pq_mdio: use dev_err_probe
  selftests: rtnetlink.sh: remove esp4_offload after test
  vsock: remove unnecessary null check in vsock_getname()
  igb: xsk: solve negative overflow of nb_pkts in zerocopy mode
  stmmac: xsk: fix negative overflow of budget in zerocopy mode
  dt-bindings: ieee802154: Convert at86rf230.txt yaml format
  net: dsa: microchip: Disable PTP function of KSZ8463
  net: dsa: microchip: Setup fiber ports for KSZ8463
  net: dsa: microchip: Write switch MAC address differently for KSZ8463
  net: dsa: microchip: Use different registers for KSZ8463
  net: dsa: microchip: Add KSZ8463 switch support to KSZ DSA driver
  dt-bindings: net: dsa: microchip: Add KSZ8463 switch support
  ...

1 files changed, 169 insertions, 22 deletions

diff --git a/drivers/net/dsa/microchip/ksz8.c b/drivers/net/dsa/microchip/ksz8.c
index be433b4e2b1c..76e490070e9c 100644
--- a/drivers/net/dsa/microchip/ksz8.c
+++ b/drivers/net/dsa/microchip/ksz8.c
@@ -3,6 +3,7 @@
  * Microchip KSZ8XXX series switch driver
  *
  * It supports the following switches:
+ * - KSZ8463
  * - KSZ8863, KSZ8873 aka KSZ88X3
  * - KSZ8895, KSZ8864 aka KSZ8895 family
  * - KSZ8794, KSZ8795, KSZ8765 aka KSZ87XX
@@ -41,7 +42,8 @@ static void ksz_cfg(struct ksz_device *dev, u32 addr, u8 bits, bool set)
 static void ksz_port_cfg(struct ksz_device *dev, int port, int offset, u8 bits,
 			 bool set)
 {
-	regmap_update_bits(ksz_regmap_8(dev), PORT_CTRL_ADDR(port, offset),
+	regmap_update_bits(ksz_regmap_8(dev),
+			   dev->dev_ops->get_port_addr(port, offset),
 			   bits, set ? bits : 0);
 }
 
@@ -140,6 +142,11 @@ int ksz8_reset_switch(struct ksz_device *dev)
 			KSZ8863_GLOBAL_SOFTWARE_RESET | KSZ8863_PCS_RESET, true);
 		ksz_cfg(dev, KSZ8863_REG_SW_RESET,
 			KSZ8863_GLOBAL_SOFTWARE_RESET | KSZ8863_PCS_RESET, false);
+	} else if (ksz_is_ksz8463(dev)) {
+		ksz_cfg(dev, KSZ8463_REG_SW_RESET,
+			KSZ8463_GLOBAL_SOFTWARE_RESET, true);
+		ksz_cfg(dev, KSZ8463_REG_SW_RESET,
+			KSZ8463_GLOBAL_SOFTWARE_RESET, false);
 	} else {
 		/* reset switch */
 		ksz_write8(dev, REG_POWER_MANAGEMENT_1,
@@ -194,6 +201,7 @@ int ksz8_change_mtu(struct ksz_device *dev, int port, int mtu)
 	case KSZ8794_CHIP_ID:
 	case KSZ8765_CHIP_ID:
 		return ksz8795_change_mtu(dev, frame_size);
+	case KSZ8463_CHIP_ID:
 	case KSZ88X3_CHIP_ID:
 	case KSZ8864_CHIP_ID:
 	case KSZ8895_CHIP_ID:
@@ -227,6 +235,11 @@ static int ksz8_port_queue_split(struct ksz_device *dev, int port, int queues)
 			       WEIGHTED_FAIR_QUEUE_ENABLE);
 		if (ret)
 			return ret;
+	} else if (ksz_is_ksz8463(dev)) {
+		mask_4q = KSZ8873_PORT_4QUEUE_SPLIT_EN;
+		mask_2q = KSZ8873_PORT_2QUEUE_SPLIT_EN;
+		reg_4q = P1CR1;
+		reg_2q = P1CR1 + 1;
 	} else {
 		mask_4q = KSZ8795_PORT_4QUEUE_SPLIT_EN;
 		mask_2q = KSZ8795_PORT_2QUEUE_SPLIT_EN;
@@ -371,6 +384,9 @@ static void ksz8863_r_mib_pkt(struct ksz_device *dev, int port, u16 addr,
 	addr -= dev->info->reg_mib_cnt;
 	ctrl_addr = addr ? KSZ8863_MIB_PACKET_DROPPED_TX_0 :
 			   KSZ8863_MIB_PACKET_DROPPED_RX_0;
+	if (ksz_is_8895_family(dev) &&
+	    ctrl_addr == KSZ8863_MIB_PACKET_DROPPED_RX_0)
+		ctrl_addr = KSZ8895_MIB_PACKET_DROPPED_RX_0;
 	ctrl_addr += port;
 	ctrl_addr |= IND_ACC_TABLE(TABLE_MIB | TABLE_READ);
 
@@ -1265,12 +1281,15 @@ int ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
 
 void ksz8_cfg_port_member(struct ksz_device *dev, int port, u8 member)
 {
+	int offset = P_MIRROR_CTRL;
 	u8 data;
 
-	ksz_pread8(dev, port, P_MIRROR_CTRL, &data);
-	data &= ~PORT_VLAN_MEMBERSHIP;
+	if (ksz_is_ksz8463(dev))
+		offset = P1CR2;
+	ksz_pread8(dev, port, offset, &data);
+	data &= ~dev->port_mask;
 	data |= (member & dev->port_mask);
-	ksz_pwrite8(dev, port, P_MIRROR_CTRL, data);
+	ksz_pwrite8(dev, port, offset, data);
 }
 
 void ksz8_flush_dyn_mac_table(struct ksz_device *dev, int port)
@@ -1278,6 +1297,8 @@ void ksz8_flush_dyn_mac_table(struct ksz_device *dev, int port)
 	u8 learn[DSA_MAX_PORTS];
 	int first, index, cnt;
 	const u16 *regs;
+	int reg = S_FLUSH_TABLE_CTRL;
+	int mask = SW_FLUSH_DYN_MAC_TABLE;
 
 	regs = dev->info->regs;
 
@@ -1295,7 +1316,11 @@ void ksz8_flush_dyn_mac_table(struct ksz_device *dev, int port)
 			ksz_pwrite8(dev, index, regs[P_STP_CTRL],
 				    learn[index] | PORT_LEARN_DISABLE);
 	}
-	ksz_cfg(dev, S_FLUSH_TABLE_CTRL, SW_FLUSH_DYN_MAC_TABLE, true);
+	if (ksz_is_ksz8463(dev)) {
+		reg = KSZ8463_FLUSH_TABLE_CTRL;
+		mask = KSZ8463_FLUSH_DYN_MAC_TABLE;
+	}
+	ksz_cfg(dev, reg, mask, true);
 	for (index = first; index < cnt; index++) {
 		if (!(learn[index] & PORT_LEARN_DISABLE))
 			ksz_pwrite8(dev, index, regs[P_STP_CTRL], learn[index]);
@@ -1434,7 +1459,7 @@ int ksz8_fdb_del(struct ksz_device *dev, int port, const unsigned char *addr,
 int ksz8_port_vlan_filtering(struct ksz_device *dev, int port, bool flag,
 			     struct netlink_ext_ack *extack)
 {
-	if (ksz_is_ksz88x3(dev))
+	if (ksz_is_ksz88x3(dev) || ksz_is_ksz8463(dev))
 		return -ENOTSUPP;
 
 	/* Discard packets with VID not enabled on the switch */
@@ -1450,9 +1475,12 @@ int ksz8_port_vlan_filtering(struct ksz_device *dev, int port, bool flag,
 
 static void ksz8_port_enable_pvid(struct ksz_device *dev, int port, bool state)
 {
-	if (ksz_is_ksz88x3(dev)) {
-		ksz_cfg(dev, REG_SW_INSERT_SRC_PVID,
-			0x03 << (4 - 2 * port), state);
+	if (ksz_is_ksz88x3(dev) || ksz_is_ksz8463(dev)) {
+		int reg = REG_SW_INSERT_SRC_PVID;
+
+		if (ksz_is_ksz8463(dev))
+			reg = KSZ8463_REG_SW_CTRL_9;
+		ksz_cfg(dev, reg, 0x03 << (4 - 2 * port), state);
 	} else {
 		ksz_pwrite8(dev, port, REG_PORT_CTRL_12, state ? 0x0f : 0x00);
 	}
@@ -1467,7 +1495,7 @@ int ksz8_port_vlan_add(struct ksz_device *dev, int port,
 	u16 data, new_pvid = 0;
 	u8 fid, member, valid;
 
-	if (ksz_is_ksz88x3(dev))
+	if (ksz_is_ksz88x3(dev) || ksz_is_ksz8463(dev))
 		return -ENOTSUPP;
 
 	/* If a VLAN is added with untagged flag different from the
@@ -1536,7 +1564,7 @@ int ksz8_port_vlan_del(struct ksz_device *dev, int port,
 	u16 data, pvid;
 	u8 fid, member, valid;
 
-	if (ksz_is_ksz88x3(dev))
+	if (ksz_is_ksz88x3(dev) || ksz_is_ksz8463(dev))
 		return -ENOTSUPP;
 
 	ksz_pread16(dev, port, REG_PORT_CTRL_VID, &pvid);
@@ -1566,19 +1594,23 @@ int ksz8_port_mirror_add(struct ksz_device *dev, int port,
 			 struct dsa_mall_mirror_tc_entry *mirror,
 			 bool ingress, struct netlink_ext_ack *extack)
 {
+	int offset = P_MIRROR_CTRL;
+
+	if (ksz_is_ksz8463(dev))
+		offset = P1CR2;
 	if (ingress) {
-		ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_RX, true);
+		ksz_port_cfg(dev, port, offset, PORT_MIRROR_RX, true);
 		dev->mirror_rx |= BIT(port);
 	} else {
-		ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_TX, true);
+		ksz_port_cfg(dev, port, offset, PORT_MIRROR_TX, true);
 		dev->mirror_tx |= BIT(port);
 	}
 
-	ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_SNIFFER, false);
+	ksz_port_cfg(dev, port, offset, PORT_MIRROR_SNIFFER, false);
 
 	/* configure mirror port */
 	if (dev->mirror_rx || dev->mirror_tx)
-		ksz_port_cfg(dev, mirror->to_local_port, P_MIRROR_CTRL,
+		ksz_port_cfg(dev, mirror->to_local_port, offset,
 			     PORT_MIRROR_SNIFFER, true);
 
 	return 0;
@@ -1587,20 +1619,23 @@ int ksz8_port_mirror_add(struct ksz_device *dev, int port,
 void ksz8_port_mirror_del(struct ksz_device *dev, int port,
 			  struct dsa_mall_mirror_tc_entry *mirror)
 {
+	int offset = P_MIRROR_CTRL;
 	u8 data;
 
+	if (ksz_is_ksz8463(dev))
+		offset = P1CR2;
 	if (mirror->ingress) {
-		ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_RX, false);
+		ksz_port_cfg(dev, port, offset, PORT_MIRROR_RX, false);
 		dev->mirror_rx &= ~BIT(port);
 	} else {
-		ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_TX, false);
+		ksz_port_cfg(dev, port, offset, PORT_MIRROR_TX, false);
 		dev->mirror_tx &= ~BIT(port);
 	}
 
-	ksz_pread8(dev, port, P_MIRROR_CTRL, &data);
+	ksz_pread8(dev, port, offset, &data);
 
 	if (!dev->mirror_rx && !dev->mirror_tx)
-		ksz_port_cfg(dev, mirror->to_local_port, P_MIRROR_CTRL,
+		ksz_port_cfg(dev, mirror->to_local_port, offset,
 			     PORT_MIRROR_SNIFFER, false);
 }
 
@@ -1625,17 +1660,24 @@ void ksz8_port_setup(struct ksz_device *dev, int port, bool cpu_port)
 	const u16 *regs = dev->info->regs;
 	struct dsa_switch *ds = dev->ds;
 	const u32 *masks;
+	int offset;
 	u8 member;
 
 	masks = dev->info->masks;
 
 	/* enable broadcast storm limit */
-	ksz_port_cfg(dev, port, P_BCAST_STORM_CTRL, PORT_BROADCAST_STORM, true);
+	offset = P_BCAST_STORM_CTRL;
+	if (ksz_is_ksz8463(dev))
+		offset = P1CR1;
+	ksz_port_cfg(dev, port, offset, PORT_BROADCAST_STORM, true);
 
 	ksz8_port_queue_split(dev, port, dev->info->num_tx_queues);
 
 	/* replace priority */
-	ksz_port_cfg(dev, port, P_802_1P_CTRL,
+	offset = P_802_1P_CTRL;
+	if (ksz_is_ksz8463(dev))
+		offset = P1CR2;
+	ksz_port_cfg(dev, port, offset,
 		     masks[PORT_802_1P_REMAPPING], false);
 
 	if (cpu_port)
@@ -1675,6 +1717,7 @@ void ksz8_config_cpu_port(struct dsa_switch *ds)
 	const u32 *masks;
 	const u16 *regs;
 	u8 remote;
+	u8 fiber_ports = 0;
 	int i;
 
 	masks = dev->info->masks;
@@ -1705,6 +1748,32 @@ void ksz8_config_cpu_port(struct dsa_switch *ds)
 		else
 			ksz_port_cfg(dev, i, regs[P_STP_CTRL],
 				     PORT_FORCE_FLOW_CTRL, false);
+		if (p->fiber)
+			fiber_ports |= (1 << i);
+	}
+	if (ksz_is_ksz8463(dev)) {
+		/* Setup fiber ports. */
+		if (fiber_ports) {
+			fiber_ports &= 3;
+			regmap_update_bits(ksz_regmap_16(dev),
+					   KSZ8463_REG_CFG_CTRL,
+					   fiber_ports << PORT_COPPER_MODE_S,
+					   0);
+			regmap_update_bits(ksz_regmap_16(dev),
+					   KSZ8463_REG_DSP_CTRL_6,
+					   COPPER_RECEIVE_ADJUSTMENT, 0);
+		}
+
+		/* Turn off PTP function as the switch's proprietary way of
+		 * handling timestamp is not supported in current Linux PTP
+		 * stack implementation.
+		 */
+		regmap_update_bits(ksz_regmap_16(dev),
+				   KSZ8463_PTP_MSG_CONF1,
+				   PTP_ENABLE, 0);
+		regmap_update_bits(ksz_regmap_16(dev),
+				   KSZ8463_PTP_CLK_CTRL,
+				   PTP_CLK_ENABLE, 0);
 	}
 }
 
@@ -1901,7 +1970,7 @@ int ksz8_setup(struct dsa_switch *ds)
 
 	ksz_cfg(dev, S_MIRROR_CTRL, SW_MIRROR_RX_TX, false);
 
-	if (!ksz_is_ksz88x3(dev))
+	if (!ksz_is_ksz88x3(dev) && !ksz_is_ksz8463(dev))
 		ksz_cfg(dev, REG_SW_CTRL_19, SW_INS_TAG_ENABLE, true);
 
 	for (i = 0; i < (dev->info->num_vlans / 4); i++)
@@ -1947,6 +2016,84 @@ u32 ksz8_get_port_addr(int port, int offset)
 	return PORT_CTRL_ADDR(port, offset);
 }
 
+u32 ksz8463_get_port_addr(int port, int offset)
+{
+	return offset + 0x18 * port;
+}
+
+static u16 ksz8463_get_phy_addr(u16 phy, u16 reg, u16 offset)
+{
+	return offset + reg * 2 + phy * (P2MBCR - P1MBCR);
+}
+
+int ksz8463_r_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 *val)
+{
+	u16 sw_reg = 0;
+	u16 data = 0;
+	int ret;
+
+	if (phy > 1)
+		return -ENOSPC;
+	switch (reg) {
+	case MII_PHYSID1:
+		sw_reg = ksz8463_get_phy_addr(phy, 0, PHY1IHR);
+		break;
+	case MII_PHYSID2:
+		sw_reg = ksz8463_get_phy_addr(phy, 0, PHY1ILR);
+		break;
+	case MII_BMCR:
+	case MII_BMSR:
+	case MII_ADVERTISE:
+	case MII_LPA:
+		sw_reg = ksz8463_get_phy_addr(phy, reg, P1MBCR);
+		break;
+	case MII_TPISTATUS:
+		/* This register holds the PHY interrupt status for simulated
+		 * Micrel KSZ PHY.
+		 */
+		data = 0x0505;
+		break;
+	default:
+		break;
+	}
+	if (sw_reg) {
+		ret = ksz_read16(dev, sw_reg, &data);
+		if (ret)
+			return ret;
+	}
+	*val = data;
+
+	return 0;
+}
+
+int ksz8463_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
+{
+	u16 sw_reg = 0;
+	int ret;
+
+	if (phy > 1)
+		return -ENOSPC;
+
+	/* No write to fiber port. */
+	if (dev->ports[phy].fiber)
+		return 0;
+	switch (reg) {
+	case MII_BMCR:
+	case MII_ADVERTISE:
+		sw_reg = ksz8463_get_phy_addr(phy, reg, P1MBCR);
+		break;
+	default:
+		break;
+	}
+	if (sw_reg) {
+		ret = ksz_write16(dev, sw_reg, val);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
 int ksz8_switch_init(struct ksz_device *dev)
 {
 	dev->cpu_port = fls(dev->info->cpu_ports) - 1;