Merge branch 'enic-set-link-speed-only-after-link-up'

John Daley says:

====================
enic: Set link speed only after link up
====================

Link: https://patch.msgid.link/20250107214159.18807-1-johndale@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

1 files changed, 32 insertions, 32 deletions

diff --git a/drivers/net/ethernet/cisco/enic/enic_main.c b/drivers/net/ethernet/cisco/enic/enic_main.c
index 9913952ccb42..49f6cab01ed5 100644
--- a/drivers/net/ethernet/cisco/enic/enic_main.c
+++ b/drivers/net/ethernet/cisco/enic/enic_main.c
@@ -109,7 +109,7 @@ static struct enic_intr_mod_table mod_table[ENIC_MAX_COALESCE_TIMERS + 1] = {
 static struct enic_intr_mod_range mod_range[ENIC_MAX_LINK_SPEEDS] = {
 	{0,  0}, /* 0  - 4  Gbps */
 	{0,  3}, /* 4  - 10 Gbps */
-	{3,  6}, /* 10 - 40 Gbps */
+	{3,  6}, /* 10+ Gbps */
 };
 
 static void enic_init_affinity_hint(struct enic *enic)
@@ -428,6 +428,36 @@ static void enic_mtu_check(struct enic *enic)
 	}
 }
 
+static void enic_set_rx_coal_setting(struct enic *enic)
+{
+	unsigned int speed;
+	int index = -1;
+	struct enic_rx_coal *rx_coal = &enic->rx_coalesce_setting;
+
+	/* 1. Read the link speed from fw
+	 * 2. Pick the default range for the speed
+	 * 3. Update it in enic->rx_coalesce_setting
+	 */
+	speed = vnic_dev_port_speed(enic->vdev);
+	if (speed > ENIC_LINK_SPEED_10G)
+		index = ENIC_LINK_40G_INDEX;
+	else if (speed > ENIC_LINK_SPEED_4G)
+		index = ENIC_LINK_10G_INDEX;
+	else
+		index = ENIC_LINK_4G_INDEX;
+
+	rx_coal->small_pkt_range_start = mod_range[index].small_pkt_range_start;
+	rx_coal->large_pkt_range_start = mod_range[index].large_pkt_range_start;
+	rx_coal->range_end = ENIC_RX_COALESCE_RANGE_END;
+
+	/* Start with the value provided by UCSM */
+	for (index = 0; index < enic->rq_count; index++)
+		enic->cq[index].cur_rx_coal_timeval =
+				enic->config.intr_timer_usec;
+
+	rx_coal->use_adaptive_rx_coalesce = 1;
+}
+
 static void enic_link_check(struct enic *enic)
 {
 	int link_status = vnic_dev_link_status(enic->vdev);
@@ -436,6 +466,7 @@ static void enic_link_check(struct enic *enic)
 	if (link_status && !carrier_ok) {
 		netdev_info(enic->netdev, "Link UP\n");
 		netif_carrier_on(enic->netdev);
+		enic_set_rx_coal_setting(enic);
 	} else if (!link_status && carrier_ok) {
 		netdev_info(enic->netdev, "Link DOWN\n");
 		netif_carrier_off(enic->netdev);
@@ -1901,36 +1932,6 @@ static void enic_synchronize_irqs(struct enic *enic)
 	}
 }
 
-static void enic_set_rx_coal_setting(struct enic *enic)
-{
-	unsigned int speed;
-	int index = -1;
-	struct enic_rx_coal *rx_coal = &enic->rx_coalesce_setting;
-
-	/* 1. Read the link speed from fw
-	 * 2. Pick the default range for the speed
-	 * 3. Update it in enic->rx_coalesce_setting
-	 */
-	speed = vnic_dev_port_speed(enic->vdev);
-	if (ENIC_LINK_SPEED_10G < speed)
-		index = ENIC_LINK_40G_INDEX;
-	else if (ENIC_LINK_SPEED_4G < speed)
-		index = ENIC_LINK_10G_INDEX;
-	else
-		index = ENIC_LINK_4G_INDEX;
-
-	rx_coal->small_pkt_range_start = mod_range[index].small_pkt_range_start;
-	rx_coal->large_pkt_range_start = mod_range[index].large_pkt_range_start;
-	rx_coal->range_end = ENIC_RX_COALESCE_RANGE_END;
-
-	/* Start with the value provided by UCSM */
-	for (index = 0; index < enic->rq_count; index++)
-		enic->cq[index].cur_rx_coal_timeval =
-				enic->config.intr_timer_usec;
-
-	rx_coal->use_adaptive_rx_coalesce = 1;
-}
-
 static int enic_dev_notify_set(struct enic *enic)
 {
 	int err;
@@ -3063,7 +3064,6 @@ static int enic_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	timer_setup(&enic->notify_timer, enic_notify_timer, 0);
 
 	enic_rfs_flw_tbl_init(enic);
-	enic_set_rx_coal_setting(enic);
 	INIT_WORK(&enic->reset, enic_reset);
 	INIT_WORK(&enic->tx_hang_reset, enic_tx_hang_reset);
 	INIT_WORK(&enic->change_mtu_work, enic_change_mtu_work);