Merge tag 'sunxi-dt-for-6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt

Allwinner Device Tree changes for 6.18

This tag contains two DT binding header changes that are shared with
the clk tree.

In this cycle we gained support for the MCU PRCM clock and reset
controller on the A523/A527/T527 family of SoCs, the NPU which is a
Vivante GC9000 IP block, and the NPU clock that was missing. The other
PRCM clock controller gained default bus clock rate settings. These
were not configured in the upstream U-boot bootloader, leading to them
running at slower rates. The assigned rates are from the user manual.

There is also a new board, the NetCube Systems Nagami SoM and two of
its carrier boards.

The A523 family development boards now have their internal RTC clocks
configured correctly, so that the RTC does not drift wildly. The missing
functions for the AXP717 on these boards are added. Missing reset GPIOs
and delays for Ethernet PHYs are added. Last, the Cubie A5E now has its
LEDs described and usable.

An overlay for the Orange Pi Zero interface (addon) board was added.
This can be used with the Orange Pi Zero and Zero Plus 2. Default audio
routing for these two boards (to be used with the addon) were added to
complement the overlay.

* tag 'sunxi-dt-for-6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  arm64: dts: allwinner: sun55i: Complete AXP717A sub-functions
  arm64: dts: allwinner: t527: orangepi-4a: hook up external 32k crystal
  arm64: dts: allwinner: t527: avaota-a1: hook up external 32k crystal
  arm64: dts: allwinner: a527: cubie-a5e: Drop external 32.768 KHz crystal
  arm64: dts: sun55i: a523: Assign standard clock rates to PRCM bus clocks
  ARM: dts: sunxi: add support for NetCube Systems Nagami Keypad Carrier
  ARM: dts: sunxi: add support for NetCube Systems Nagami Basic Carrier
  ARM: dts: sunxi: add support for NetCube Systems Nagami SoM
  riscv: dts: allwinner: d1s-t113: Add pinctrl's required by NetCube Systems Nagami SoM
  dt-bindings: arm: sunxi: Add NetCube Systems Nagami SoM and carrier board bindings
  ARM: dts: allwinner: Add Orange Pi Zero Interface Board overlay
  ARM: dts: allwinner: orangepi-zero-plus2: Add default audio routing
  ARM: dts: allwinner: orangepi-zero: Add default audio routing
  arm64: dts: allwinner: a523: Add NPU device node
  arm64: dts: allwinner: a523: Add MCU PRCM CCU node
  dt-bindings: clock: sun55i-a523-ccu: Add A523 MCU CCU clock controller
  dt-bindings: clock: sun55i-a523-ccu: Add missing NPU module clock
  arm64: dts: allwinner: t527: avaota-a1: Add ethernet PHY reset setting
  arm64: dts: allwinner: a527: cubie-a5e: Add ethernet PHY reset setting
  arm64: dts: allwinner: a527: cubie-a5e: Add LEDs

Link: https://lore.kernel.org/r/aMrtuZg8HlR--TAt@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

17 files changed, 853 insertions, 7 deletions

diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index c25a22fe4d25..72ef861a0b68 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -595,6 +595,14 @@ properties:
           - const: netcube,kumquat
           - const: allwinner,sun8i-v3s
 
+      - description: NetCube Systems Nagami SoM based boards
+        items:
+          - enum:
+              - netcube,nagami-basic-carrier
+              - netcube,nagami-keypad-carrier
+          - const: netcube,nagami
+          - const: allwinner,sun8i-t113s
+
       - description: NextThing Co. CHIP
         items:
           - const: nextthing,chip
diff --git a/Documentation/devicetree/bindings/clock/allwinner,sun55i-a523-ccu.yaml b/Documentation/devicetree/bindings/clock/allwinner,sun55i-a523-ccu.yaml
index f5f62e9a10a1..58be701a720e 100644
--- a/Documentation/devicetree/bindings/clock/allwinner,sun55i-a523-ccu.yaml
+++ b/Documentation/devicetree/bindings/clock/allwinner,sun55i-a523-ccu.yaml
@@ -19,6 +19,7 @@ properties:
   compatible:
     enum:
       - allwinner,sun55i-a523-ccu
+      - allwinner,sun55i-a523-mcu-ccu
       - allwinner,sun55i-a523-r-ccu
 
   reg:
@@ -26,11 +27,11 @@ properties:
 
   clocks:
     minItems: 4
-    maxItems: 5
+    maxItems: 9
 
   clock-names:
     minItems: 4
-    maxItems: 5
+    maxItems: 9
 
 required:
   - "#clock-cells"
@@ -67,6 +68,38 @@ allOf:
       properties:
         compatible:
           enum:
+            - allwinner,sun55i-a523-mcu-ccu
+
+    then:
+      properties:
+        clocks:
+          items:
+            - description: High Frequency Oscillator (usually at 24MHz)
+            - description: Low Frequency Oscillator (usually at 32kHz)
+            - description: Internal Oscillator
+            - description: Audio PLL (4x)
+            - description: Peripherals PLL 0 (300 MHz output)
+            - description: DSP module clock
+            - description: MBUS clock
+            - description: PRCM AHB clock
+            - description: PRCM APB0 clock
+
+        clock-names:
+          items:
+            - const: hosc
+            - const: losc
+            - const: iosc
+            - const: pll-audio0-4x
+            - const: pll-periph0-300m
+            - const: dsp
+            - const: mbus
+            - const: r-ahb
+            - const: r-apb0
+
+  - if:
+      properties:
+        compatible:
+          enum:
             - allwinner,sun55i-a523-r-ccu
 
     then:
diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
index d799ad153b37..f71392a55df8 100644
--- a/arch/arm/boot/dts/allwinner/Makefile
+++ b/arch/arm/boot/dts/allwinner/Makefile
@@ -182,6 +182,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-wits-pro-a20-dkt.dtb
 
 # Enables support for device-tree overlays for all pis
+DTC_FLAGS_sun8i-h2-plus-orangepi-zero := -@
 DTC_FLAGS_sun8i-h3-orangepi-lite := -@
 DTC_FLAGS_sun8i-h3-bananapi-m2-plus := -@
 DTC_FLAGS_sun8i-h3-nanopi-m1-plus := -@
@@ -199,6 +200,7 @@ DTC_FLAGS_sun8i-h3-nanopi-r1 := -@
 DTC_FLAGS_sun8i-h3-orangepi-pc := -@
 DTC_FLAGS_sun8i-h3-bananapi-m2-plus-v1.2 := -@
 DTC_FLAGS_sun8i-h3-orangepi-pc-plus := -@
+DTC_FLAGS_sun8i-t113s-netcube-nagami-basic-carrier := -@
 DTC_FLAGS_sun8i-v3s-netcube-kumquat := -@
 dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a23-evb.dtb \
@@ -225,6 +227,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-h2-plus-libretech-all-h3-cc.dtb \
 	sun8i-h2-plus-orangepi-r1.dtb \
 	sun8i-h2-plus-orangepi-zero.dtb \
+	sun8i-h2-plus-orangepi-zero-interface-board.dtb \
 	sun8i-h3-bananapi-m2-plus.dtb \
 	sun8i-h3-bananapi-m2-plus-v1.2.dtb \
 	sun8i-h3-beelink-x2.dtb \
@@ -244,6 +247,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-h3-orangepi-plus.dtb \
 	sun8i-h3-orangepi-plus2e.dtb \
 	sun8i-h3-orangepi-zero-plus2.dtb \
+	sun8i-h3-orangepi-zero-plus2-interface-board.dtb \
 	sun8i-h3-rervision-dvk.dtb \
 	sun8i-h3-zeropi.dtb \
 	sun8i-h3-emlid-neutis-n5h3-devboard.dtb \
@@ -257,6 +261,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-s3-lichee-zero-plus.dtb \
 	sun8i-s3-pinecube.dtb \
 	sun8i-t113s-mangopi-mq-r-t113.dtb \
+	sun8i-t113s-netcube-nagami-basic-carrier.dtb \
+	sun8i-t113s-netcube-nagami-keypad-carrier.dtb \
 	sun8i-t3-cqa3t-bv3.dtb \
 	sun8i-v3-sl631-imx179.dtb \
 	sun8i-v3s-anbernic-rg-nano.dtb \
@@ -264,6 +270,10 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-v3s-licheepi-zero-dock.dtb \
 	sun8i-v3s-netcube-kumquat.dtb \
 	sun8i-v40-bananapi-m2-berry.dtb
+sun8i-h2-plus-orangepi-zero-interface-board-dtbs += \
+	sun8i-h2-plus-orangepi-zero.dtb sun8i-orangepi-zero-interface-board.dtbo
+sun8i-h3-orangepi-zero-plus2-interface-board-dtbs += \
+	sun8i-h3-orangepi-zero-plus2.dtb sun8i-orangepi-zero-interface-board.dtbo
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
 	sun9i-a80-cubieboard4.dtb
diff --git a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
index 1b001f2ad0ef..b23cec5b89eb 100644
--- a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
@@ -112,6 +112,20 @@
 	};
 };
 
+/*
+ * Audio input/output is exposed on the 13-pin header and can't be used for
+ * anything else. However, adapter boards may use different audio routing.
+ * - https://linux-sunxi.org/Xunlong_Orange_Pi_Zero#Expansion_Port
+ * - Allwinner H3 Datasheet, section 3.1. Pin Characteristics
+ */
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "disabled";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_vdd_cpux>;
 };
diff --git a/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
index 7a6444a10e25..97a3565ac7a8 100644
--- a/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
@@ -99,6 +99,20 @@
 	};
 };
 
+/*
+ * Audio input/output is exposed on the 13-pin header and can't be used for
+ * anything else. However, adapter boards may use different audio routing.
+ * - http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-Zero-Plus-2.html
+ * - Allwinner H3 Datasheet, section 3.1. Pin Characteristics
+ */
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "disabled";
+};
+
 &de {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/allwinner/sun8i-orangepi-zero-interface-board.dtso b/arch/arm/boot/dts/allwinner/sun8i-orangepi-zero-interface-board.dtso
new file mode 100644
index 000000000000..e137eefee341
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-orangepi-zero-interface-board.dtso
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR X11)
+/*
+ * Copyright (C) 2025 J. Neuschäfer <j.ne@posteo.net>
+ *
+ * Devicetree overlay for the Orange Pi Zero Interface board (OP0014).
+ *
+ *   https://orangepi.com/index.php?route=product/product&product_id=871
+ *
+ * This overlay applies to the following base files:
+ *
+ * - arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
+ * - arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
+ */
+
+/dts-v1/;
+/plugin/;
+
+&codec {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&r_ir_rx_pin>;
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-basic-carrier.dts b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-basic-carrier.dts
new file mode 100644
index 000000000000..5262102a85f6
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-basic-carrier.dts
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-t113s-netcube-nagami.dtsi"
+
+/ {
+	model = "NetCube Systems Nagami Basic Carrier Board";
+	compatible = "netcube,nagami-basic-carrier", "netcube,nagami",
+		     "allwinner,sun8i-t113s";
+};
+
+&can0 {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2s1 {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	broken-cd;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&spi1 {
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-keypad-carrier.dts b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-keypad-carrier.dts
new file mode 100644
index 000000000000..4ffa6a0216d8
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-keypad-carrier.dts
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-t113s-netcube-nagami.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "NetCube Systems Nagami Keypad Carrier Board";
+	compatible = "netcube,nagami-keypad-carrier", "netcube,nagami",
+		     "allwinner,sun8i-t113s";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_red: led-status-red {
+			gpios = <&pio 3 16 GPIO_ACTIVE_HIGH>;  /* PD16 */
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_STATUS;
+		};
+
+		led_status_green: led-status-green {
+			gpios = <&pio 3 22 GPIO_ACTIVE_HIGH>;  /* PD22 */
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	tca8418: keypad@34 {
+		compatible = "ti,tca8418";
+		reg = <0x34>;
+		interrupts-extended = <&pio 5 6 IRQ_TYPE_EDGE_FALLING>;  /* PF6 */
+		linux,keymap = <MATRIX_KEY(0x03, 0x00, KEY_NUMERIC_A)
+				MATRIX_KEY(0x03, 0x01, KEY_NUMERIC_1)
+				MATRIX_KEY(0x03, 0x02, KEY_NUMERIC_2)
+				MATRIX_KEY(0x03, 0x03, KEY_NUMERIC_3)
+				MATRIX_KEY(0x02, 0x00, KEY_NUMERIC_B)
+				MATRIX_KEY(0x02, 0x01, KEY_NUMERIC_4)
+				MATRIX_KEY(0x02, 0x02, KEY_NUMERIC_5)
+				MATRIX_KEY(0x02, 0x03, KEY_NUMERIC_6)
+				MATRIX_KEY(0x01, 0x00, KEY_NUMERIC_C)
+				MATRIX_KEY(0x01, 0x01, KEY_NUMERIC_7)
+				MATRIX_KEY(0x01, 0x02, KEY_NUMERIC_8)
+				MATRIX_KEY(0x01, 0x03, KEY_NUMERIC_9)
+				MATRIX_KEY(0x00, 0x00, KEY_NUMERIC_D)
+				MATRIX_KEY(0x00, 0x01, KEY_CLEAR)
+				MATRIX_KEY(0x00, 0x02, KEY_NUMERIC_0)
+				MATRIX_KEY(0x00, 0x03, KEY_OK)
+		>;
+		keypad,num-rows = <4>;
+		keypad,num-columns = <4>;
+	};
+};
+
+&pio {
+	gpio-line-names = "", "", "", "", // PA
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PB
+			  "", "", "UART3_TX", "UART3_RX",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "eMMC_CLK", "eMMC_CMD", // PC
+			  "eMMC_D2", "eMMC_D1", "eMMC_D0", "eMMC_D3",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PD
+			  "", "", "", "",
+			  "", "USB_SEC_EN", "", "",
+			  "", "", "", "",
+			  "LED_STATUS_RED", "", "", "",
+			  "I2C2_SCL", "I2C2_SDA", "LED_STATUS_GREEN", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ETH_CRSDV", "ETH_RXD0", "ETH_RXD1", "ETH_TXCK", // PE
+			  "ETH_TXD0", "ETH_TXD1", "ETH_TXEN", "",
+			  "ETH_MDC", "ETH_MDIO", "QWIIC_nINT", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PF
+			  "", "", "KEY_nINT", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ESP_CLK", "ESP_CMD", "ESP_D0", "ESP_D1", // PG
+			  "ESP_D2", "ESP_D3", "UART1_TXD", "UART1_RXD",
+			  "ESP_nBOOT", "ESP_nRST", "I2C3_SCL", "I2C3_SDA",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami.dtsi b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami.dtsi
new file mode 100644
index 000000000000..544d60cfc32e
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami.dtsi
@@ -0,0 +1,250 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-t113s.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "NetCube Systems Nagami SoM";
+	compatible = "netcube,nagami", "allwinner,sun8i-t113s";
+
+	aliases {
+		serial1 = &uart1; // ESP32 Bootloader UART
+		serial3 = &uart3; // Console UART on Card Edge
+		ethernet0 = &emac;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	/* module wide 3.3V supply directly from the card edge */
+	reg_vcc3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	/* SY8008 DC/DC regulator on the board, also supplying VDD-SYS */
+	reg_vcc_core: regulator-core {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-core";
+		regulator-min-microvolt = <880000>;
+		regulator-max-microvolt = <880000>;
+		vin-supply = <&reg_vcc3v3>;
+	};
+
+	/* USB0 MUX to switch connect to Card-Edge only after BootROM */
+	usb0_sec_mux: mux-controller{
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&pio 3 9 GPIO_ACTIVE_HIGH>; /* PD9 */
+		idle-state = <1>; /* USB connected to Card-Edge by default */
+	};
+
+	/* Reset of ESP32 */
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 9 GPIO_ACTIVE_LOW>; /* PG9 */
+		post-power-on-delay-ms = <1500>;
+		power-off-delay-us = <200>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&cpu1 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&emac {
+	nvmem-cells = <&eth0_macaddress>;
+	nvmem-cell-names = "mac-address";
+	phy-handle = <&lan8720a>;
+	phy-mode = "rmii";
+	pinctrl-0 = <&rmii_pe_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Default I2C Interface on Card-Edge */
+&i2c2 {
+	pinctrl-0 = <&i2c2_pd_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+/* Exposed as the QWIIC connector and used by the internal EEPROM */
+&i2c3 {
+	pinctrl-0 = <&i2c3_pg_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	eeprom0: eeprom@50 {
+		compatible = "atmel,24c02";		/* actually it's a 24AA02E48 */
+		reg = <0x50>;
+		pagesize = <16>;
+		read-only;
+		vcc-supply = <&reg_vcc3v3>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		eth0_macaddress: macaddress@fa {
+			reg = <0xfa 0x06>;
+		};
+	};
+};
+
+/* Default I2S Interface on Card-Edge */
+&i2s1 {
+	pinctrl-0 = <&i2s1_pins>, <&i2s1_din0_pin>, <&i2s1_dout0_pin>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+/* Phy is on SoM. MDI signals pre-magnetics are on the card edge */
+&mdio {
+	lan8720a: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+/* Default SD Interface on Card-Edge */
+&mmc0 {
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+/* Connected to the on-board ESP32 */
+&mmc1 {
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	status = "okay";
+};
+
+/* Connected to the on-board eMMC */
+&mmc2 {
+	pinctrl-0 = <&mmc2_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_vcc3v3>;
+	vcc-pc-supply = <&reg_vcc3v3>;
+	vcc-pd-supply = <&reg_vcc3v3>;
+	vcc-pe-supply = <&reg_vcc3v3>;
+	vcc-pf-supply = <&reg_vcc3v3>;
+	vcc-pg-supply = <&reg_vcc3v3>;
+
+	gpio-line-names = "", "", "", "", // PA
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "CAN0_TX", "CAN0_RX", // PB
+			  "CAN1_TX", "CAN1_RX", "UART3_TX", "UART3_RX",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "eMMC_CLK", "eMMC_CMD", // PC
+			  "eMMC_D2", "eMMC_D1", "eMMC_D0", "eMMC_D3",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PD
+			  "", "", "", "",
+			  "", "USB_SEC_EN", "SPI1_CS", "SPI1_CLK",
+			  "SPI1_MOSI", "SPI1_MISO", "SPI1_HOLD", "SPI1_WP",
+			  "PD16", "", "", "",
+			  "I2C2_SCL", "I2C2_SDA", "PD22", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ETH_CRSDV", "ETH_RXD0", "ETH_RXD1", "ETH_TXCK", // PE
+			  "ETH_TXD0", "ETH_TXD1", "ETH_TXEN", "",
+			  "ETH_MDC", "ETH_MDIO", "QWIIC_nINT", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "SD_D1", "SD_D0", "SD_CLK", "SD_CLK", // PF
+			  "SD_D3", "SD_D2", "PF6", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ESP_CLK", "ESP_CMD", "ESP_D0", "ESP_D1", // PG
+			  "ESP_D2", "ESP_D3", "UART1_TXD", "UART1_RXD",
+			  "ESP_nBOOT", "ESP_nRST", "I2C3_SCL", "I2C3_SDA",
+			  "I2S1_WS", "I2S1_CLK", "I2S1_DIN0", "I2S1_DOUT0",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+/* Remove the unused CK pin from the pinctl as it is unconnected */
+&rmii_pe_pins {
+	pins = "PE0", "PE1", "PE2", "PE3", "PE4",
+	       "PE5", "PE6", "PE8", "PE9";
+};
+
+/* Default SPI Interface on Card-Edge */
+&spi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-0 = <&spi1_pins>, <&spi1_hold_pin>, <&spi1_wp_pin>;
+	pinctrl-names = "default";
+	cs-gpios = <0>;
+	status = "disabled";
+};
+
+/* Connected to the Bootloader/Console of the ESP32 */
+&uart1 {
+	pinctrl-0 = <&uart1_pg6_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Console/Debug UART on Card-Edge */
+&uart3 {
+	pinctrl-0 = <&uart3_pb_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi b/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
index 6b6f2296bdff..7b36c47a3a13 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
@@ -4,8 +4,10 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun55i-a523-ccu.h>
+#include <dt-bindings/clock/sun55i-a523-mcu-ccu.h>
 #include <dt-bindings/clock/sun55i-a523-r-ccu.h>
 #include <dt-bindings/reset/sun55i-a523-ccu.h>
+#include <dt-bindings/reset/sun55i-a523-mcu-ccu.h>
 #include <dt-bindings/reset/sun55i-a523-r-ccu.h>
 #include <dt-bindings/power/allwinner,sun55i-a523-ppu.h>
 #include <dt-bindings/power/allwinner,sun55i-a523-pck-600.h>
@@ -624,6 +626,8 @@
 				      "pll-audio";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
+			assigned-clocks = <&r_ccu CLK_R_AHB>, <&r_ccu CLK_R_APB0>;
+			assigned-clock-rates = <200000000>, <100000000>;
 		};
 
 		nmi_intc: interrupt-controller@7010320 {
@@ -690,5 +694,42 @@
 			clock-names = "bus", "hosc", "ahb";
 			#clock-cells = <1>;
 		};
+
+		mcu_ccu: clock-controller@7102000 {
+			compatible = "allwinner,sun55i-a523-mcu-ccu";
+			reg = <0x7102000 0x200>;
+			clocks = <&osc24M>,
+				 <&rtc CLK_OSC32K>,
+				 <&rtc CLK_IOSC>,
+				 <&ccu CLK_PLL_AUDIO0_4X>,
+				 <&ccu CLK_PLL_PERIPH0_300M>,
+				 <&ccu CLK_DSP>,
+				 <&ccu CLK_MBUS>,
+				 <&r_ccu CLK_R_AHB>,
+				 <&r_ccu CLK_R_APB0>;
+			clock-names = "hosc",
+				      "losc",
+				      "iosc",
+				      "pll-audio0-4x",
+				      "pll-periph0-300m",
+				      "dsp",
+				      "mbus",
+				      "r-ahb",
+				      "r-apb0";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		npu: npu@7122000 {
+			compatible = "vivante,gc";
+			reg = <0x07122000 0x1000>;
+			interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mcu_ccu CLK_BUS_MCU_NPU_ACLK>,
+				 <&ccu CLK_NPU>,
+				 <&mcu_ccu CLK_BUS_MCU_NPU_HCLK>;
+			clock-names = "bus", "core", "reg";
+			resets = <&mcu_ccu RST_BUS_MCU_NPU>;
+			power-domains = <&ppu PD_NPU>;
+		};
 	};
 };
diff --git a/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts b/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
index 553ad774ed13..f82a8d121697 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
+++ b/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
@@ -6,6 +6,7 @@
 #include "sun55i-a523.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 
 / {
 	model = "Radxa Cubie A5E";
@@ -20,11 +21,28 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	ext_osc32k: ext-osc32k-clk {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <32768>;
-		clock-output-names = "ext_osc32k";
+	leds {
+		compatible = "gpio-leds";
+
+		power-led {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>; /* PL4 */
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		use-led {
+			function = LED_FUNCTION_ACTIVITY;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&axp717_adc 3>, /* vsys_v */
+			      <&axp717_adc 4>; /* pmic_temp */
 	};
 
 	reg_vcc5v: vcc5v {
@@ -75,6 +93,9 @@
 	ext_rgmii_phy: ethernet-phy@1 {
 		compatible = "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
+		reset-gpios = <&pio 7 8 GPIO_ACTIVE_LOW>; /* PH8 */
+		reset-assert-us = <10000>;
+		reset-deassert-us = <150000>;
 	};
 };
 
@@ -125,6 +146,17 @@
 		bldoin-supply = <&reg_vcc5v>;
 		cldoin-supply = <&reg_vcc5v>;
 
+		axp717_adc: adc {
+			compatible = "x-powers,axp717-adc";
+			#io-channel-cells = <1>;
+		};
+
+		battery-power {
+			compatible = "x-powers,axp717-battery-power-supply";
+			/* charger mode design but has no battery terminal */
+			status = "disabled";
+		};
+
 		regulators {
 			/* Supplies the "little" cluster (1.4 GHz cores) */
 			reg_dcdc1: dcdc1 {
@@ -228,6 +260,10 @@
 				regulator-name = "vdd-cpus";
 			};
 		};
+
+		usb-power {
+			compatible = "x-powers,axp717-usb-power-supply";
+		};
 	};
 
 	axp323: pmic@36 {
diff --git a/arch/arm64/boot/dts/allwinner/sun55i-t527-avaota-a1.dts b/arch/arm64/boot/dts/allwinner/sun55i-t527-avaota-a1.dts
index b9eeb6753e9e..1b054fa8ef74 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-t527-avaota-a1.dts
+++ b/arch/arm64/boot/dts/allwinner/sun55i-t527-avaota-a1.dts
@@ -27,6 +27,12 @@
 		clock-output-names = "ext_osc32k";
 	};
 
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&axp717_adc 3>, /* vsys_v */
+			      <&axp717_adc 4>; /* pmic_temp */
+	};
+
 	reg_vcc12v: vcc12v {
 		/* DC input jack */
 		compatible = "regulator-fixed";
@@ -85,6 +91,9 @@
 	ext_rgmii_phy: ethernet-phy@1 {
 		compatible = "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
+		reset-gpios = <&pio 7 8 GPIO_ACTIVE_LOW>; /* PH8 */
+		reset-assert-us = <10000>;
+		reset-deassert-us = <150000>;
 	};
 };
 
@@ -146,6 +155,17 @@
 		bldoin-supply = <&reg_vcc5v>;
 		cldoin-supply = <&reg_vcc5v>;
 
+		axp717_adc: adc {
+			compatible = "x-powers,axp717-adc";
+			#io-channel-cells = <1>;
+		};
+
+		battery-power {
+			compatible = "x-powers,axp717-battery-power-supply";
+			/* no battery; output used for dcdc4 instead */
+			status = "disabled";
+		};
+
 		regulators {
 			/* Supplies the "little" cluster (1.4 GHz cores) */
 			reg_dcdc1: dcdc1 {
@@ -252,6 +272,12 @@
 				regulator-name = "vdd-cpus";
 			};
 		};
+
+		usb-power {
+			compatible = "x-powers,axp717-usb-power-supply";
+			/* 12V-5V buck converter can supply up to 5A */
+			input-current-limit-microamp = <3250000>;
+		};
 	};
 
 	axp323: pmic@36 {
@@ -306,6 +332,14 @@
 	vcc-pm-supply = <&reg_aldo3>;
 };
 
+&rtc {
+	clocks = <&r_ccu CLK_BUS_R_RTC>, <&osc24M>,
+		 <&r_ccu CLK_R_AHB>, <&ext_osc32k>;
+	clock-names = "bus", "hosc", "ahb", "ext-osc32k";
+	assigned-clocks = <&rtc CLK_OSC32K>;
+	assigned-clock-rates = <32768>;
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pb_pins>;
diff --git a/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts b/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts
index d07bb9193b43..39a4e194712a 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts
+++ b/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts
@@ -40,6 +40,13 @@
 		};
 	};
 
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&axp717_adc 3>, /* vsys_v */
+			      <&axp717_adc 4>, /* pmic_temp */
+			      <&axp717_adc 7>; /* bkup_batt_v */
+	};
+
 	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 1 1 GPIO_ACTIVE_LOW>; /* PM1 */
@@ -174,6 +181,17 @@
 		bldoin-supply = <&reg_vcc5v>;
 		cldoin-supply = <&reg_vcc5v>;
 
+		axp717_adc: adc {
+			compatible = "x-powers,axp717-adc";
+			#io-channel-cells = <1>;
+		};
+
+		battery-power {
+			compatible = "x-powers,axp717-battery-power-supply";
+			/* no battery; output used for dcdc4 instead */
+			status = "disabled";
+		};
+
 		regulators {
 			/* Supplies the "little" cluster (1.4 GHz cores) */
 			reg_dcdc1: dcdc1 {
@@ -288,6 +306,11 @@
 				regulator-name = "vdd-cpus-usb-0v9";
 			};
 		};
+
+		usb-power {
+			compatible = "x-powers,axp717-usb-power-supply";
+			input-current-limit-microamp = <3000000>;
+		};
 	};
 
 	axp323: pmic@36 {
@@ -346,6 +369,14 @@
 	vcc-pm-supply = <&reg_bldo2>;
 };
 
+&rtc {
+	clocks = <&r_ccu CLK_BUS_R_RTC>, <&osc24M>,
+		 <&r_ccu CLK_R_AHB>, <&ext_osc32k>;
+	clock-names = "bus", "hosc", "ahb", "ext-osc32k";
+	assigned-clocks = <&rtc CLK_OSC32K>;
+	assigned-clock-rates = <32768>;
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pb_pins>;
diff --git a/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi
index e4175adb028d..63e252b44973 100644
--- a/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi
+++ b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi
@@ -79,6 +79,36 @@
 			};
 
 			/omit-if-no-ref/
+			i2c2_pd_pins: i2c2-pd-pins {
+				pins = "PD20", "PD21";
+				function = "i2c2";
+			};
+
+			/omit-if-no-ref/
+			i2c3_pg_pins: i2c3-pg-pins {
+				pins = "PG10", "PG11";
+				function = "i2c3";
+			};
+
+			/omit-if-no-ref/
+			i2s1_pins: i2s1-pins {
+				pins = "PG12", "PG13";
+				function = "i2s1";
+			};
+
+			/omit-if-no-ref/
+			i2s1_din0_pin: i2s1-din0-pin {
+				pins = "PG14";
+				function = "i2s1_din";
+			};
+
+			/omit-if-no-ref/
+			i2s1_dout0_pin: i2s1-dout0-pin {
+				pins = "PG15";
+				function = "i2s1_dout";
+			};
+
+			/omit-if-no-ref/
 			lcd_rgb666_pins: lcd-rgb666-pins {
 				pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5",
 				       "PD6", "PD7", "PD8", "PD9", "PD10", "PD11",
@@ -127,6 +157,24 @@
 			};
 
 			/omit-if-no-ref/
+			spi1_pins: spi1-pins {
+				pins = "PD10", "PD11", "PD12", "PD13";
+				function = "spi1";
+			};
+
+			/omit-if-no-ref/
+			spi1_hold_pin: spi1-hold-pin {
+				pins = "PD14";
+				function = "spi1";
+			};
+
+			/omit-if-no-ref/
+			spi1_wp_pin: spi1-wp-pin {
+				pins = "PD15";
+				function = "spi1";
+			};
+
+			/omit-if-no-ref/
 			uart1_pg6_pins: uart1-pg6-pins {
 				pins = "PG6", "PG7";
 				function = "uart1";
diff --git a/include/dt-bindings/clock/sun55i-a523-ccu.h b/include/dt-bindings/clock/sun55i-a523-ccu.h
index c8259ac5ada7..54808fcfd556 100644
--- a/include/dt-bindings/clock/sun55i-a523-ccu.h
+++ b/include/dt-bindings/clock/sun55i-a523-ccu.h
@@ -185,5 +185,6 @@
 #define CLK_FANOUT0		176
 #define CLK_FANOUT1		177
 #define CLK_FANOUT2		178
+#define CLK_NPU			179
 
 #endif /* _DT_BINDINGS_CLK_SUN55I_A523_CCU_H_ */
diff --git a/include/dt-bindings/clock/sun55i-a523-mcu-ccu.h b/include/dt-bindings/clock/sun55i-a523-mcu-ccu.h
new file mode 100644
index 000000000000..6efc6bc7e11a
--- /dev/null
+++ b/include/dt-bindings/clock/sun55i-a523-mcu-ccu.h
@@ -0,0 +1,54 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Copyright (C) 2025 Chen-Yu Tsai <wens@csie.org>
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN55I_A523_MCU_CCU_H_
+#define _DT_BINDINGS_CLK_SUN55I_A523_MCU_CCU_H_
+
+#define CLK_MCU_PLL_AUDIO1	0
+#define CLK_MCU_PLL_AUDIO1_DIV2	1
+#define CLK_MCU_PLL_AUDIO1_DIV5	2
+#define CLK_MCU_AUDIO_OUT	3
+#define CLK_MCU_DSP		4
+#define CLK_MCU_I2S0		5
+#define CLK_MCU_I2S1		6
+#define CLK_MCU_I2S2		7
+#define CLK_MCU_I2S3		8
+#define CLK_MCU_I2S3_ASRC	9
+#define CLK_BUS_MCU_I2S0	10
+#define CLK_BUS_MCU_I2S1	11
+#define CLK_BUS_MCU_I2S2	12
+#define CLK_BUS_MCU_I2S3	13
+#define CLK_MCU_SPDIF_TX	14
+#define CLK_MCU_SPDIF_RX	15
+#define CLK_BUS_MCU_SPDIF	16
+#define CLK_MCU_DMIC		17
+#define CLK_BUS_MCU_DMIC	18
+#define CLK_MCU_AUDIO_CODEC_DAC	19
+#define CLK_MCU_AUDIO_CODEC_ADC	20
+#define CLK_BUS_MCU_AUDIO_CODEC	21
+#define CLK_BUS_MCU_DSP_MSGBOX	22
+#define CLK_BUS_MCU_DSP_CFG	23
+#define CLK_BUS_MCU_NPU_HCLK	24
+#define CLK_BUS_MCU_NPU_ACLK	25
+#define CLK_MCU_TIMER0		26
+#define CLK_MCU_TIMER1		27
+#define CLK_MCU_TIMER2		28
+#define CLK_MCU_TIMER3		29
+#define CLK_MCU_TIMER4		30
+#define CLK_MCU_TIMER5		31
+#define CLK_BUS_MCU_TIMER	32
+#define CLK_BUS_MCU_DMA		33
+#define CLK_MCU_TZMA0		34
+#define CLK_MCU_TZMA1		35
+#define CLK_BUS_MCU_PUBSRAM	36
+#define CLK_MCU_MBUS_DMA	37
+#define CLK_MCU_MBUS		38
+#define CLK_MCU_RISCV		39
+#define CLK_BUS_MCU_RISCV_CFG	40
+#define CLK_BUS_MCU_RISCV_MSGBOX	41
+#define CLK_MCU_PWM0		42
+#define CLK_BUS_MCU_PWM0	43
+
+#endif /* _DT_BINDINGS_CLK_SUN55I_A523_MCU_CCU_H_ */
diff --git a/include/dt-bindings/reset/sun55i-a523-mcu-ccu.h b/include/dt-bindings/reset/sun55i-a523-mcu-ccu.h
new file mode 100644
index 000000000000..a89a0b44f08b
--- /dev/null
+++ b/include/dt-bindings/reset/sun55i-a523-mcu-ccu.h
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Copyright (C) 2025 Chen-Yu Tsai <wens@csie.org>
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN55I_A523_MCU_CCU_H_
+#define _DT_BINDINGS_RST_SUN55I_A523_MCU_CCU_H_
+
+#define RST_BUS_MCU_I2S0		0
+#define RST_BUS_MCU_I2S1		1
+#define RST_BUS_MCU_I2S2		2
+#define RST_BUS_MCU_I2S3		3
+#define RST_BUS_MCU_SPDIF		4
+#define RST_BUS_MCU_DMIC		5
+#define RST_BUS_MCU_AUDIO_CODEC		6
+#define RST_BUS_MCU_DSP_MSGBOX		7
+#define RST_BUS_MCU_DSP_CFG		8
+#define RST_BUS_MCU_NPU			9
+#define RST_BUS_MCU_TIMER		10
+#define RST_BUS_MCU_DSP_DEBUG		11
+#define RST_BUS_MCU_DSP			12
+#define RST_BUS_MCU_DMA			13
+#define RST_BUS_MCU_PUBSRAM		14
+#define RST_BUS_MCU_RISCV_CFG		15
+#define RST_BUS_MCU_RISCV_DEBUG		16
+#define RST_BUS_MCU_RISCV_CORE		17
+#define RST_BUS_MCU_RISCV_MSGBOX	18
+#define RST_BUS_MCU_PWM0		19
+
+#endif /* _DT_BINDINGS_RST_SUN55I_A523_MCU_CCU_H_ */