| Age | Commit message (Collapse) | Author |
|---|
|
Always call cs_dsp_power_up() and cs_dsp_run() in
cs35l56_hda_fw_load() even if there aren't any firmware files
to download. Also, if there aren't any firmware files to
download there is no need to do cs35l56_firmware_shutdown() and
cs35l56_system_reset().
If there aren't any firmware files there's no need to write
anything to the CS35L56 registers to make it work - it will
already be running the ROM firmware. So it's not strictly
necessary to start cs_dsp.
But it's perfectly ok to call cs_dsp_power_up() and
cs_dsp_run() without downloading any firmware. This avoids
having to support a state where audio is playing but cs_dsp
is not running.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-5-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When firmware is reloaded after a system resume cs_dsp_power_down() should
be called before calling cs_dsp_power_up().
The fw_patched flag should also be cleared and only set again if the
firmware download succeeded.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-4-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Only call regcache_mark_dirty() in cs35l56_hda_fw_load() if
the CS35L56 was SYSTEM_RESET.
recache_mark_dirty() changes the behaviour of regcache_sync()
to write out cache values that are not the default value, and
skip cache values that are the default.
AUDIO_REINIT does not reset the registers. regcache_mark_dirty()
after AUDIO_REINIT could cause the regcache_sync() to sync
registers incorrectly because it will assume that all registers
have reset to default.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-3-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Move the call to cs_dsp_run() in cs35l56_hda_fw_load() so that it
is after the CS35L56 has been reset/reinit'd and the regmap
cache has been synced.
cs_dsp_run() syncs up ALSA control cache values with the DSP memory
so this must not be done until the firmware has reinitialized.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-2-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
`strncpy` is deprecated for use on NUL-terminated destination strings [1].
A suitable replacement is `strscpy` [2] due to the fact that it
guarantees NUL-termination on its destination buffer argument which is
_not_ always the case for `strncpy`!
It should be noted that, in this case, the destination buffer has a
length strictly greater than the source string. Moreover, the source
string is NUL-terminated (and so is the destination) which means there
was no real bug happening here. Nonetheless, this patch would get us one
step closer to eliminating the `strncpy` API in the kernel, as its use
is too ambiguous. We need to favor less ambiguous replacements such as:
strscpy, strscpy_pad, strtomem and strtomem_pad (amongst others).
Technically, my patch yields subtly different behavior. The original
implementation with `strncpy` would fill the entire destination buffer
with null bytes [3] while `strscpy` will leave the junk, uninitialized
bytes trailing after the _mandatory_ NUL-termination. So, if somehow
`card->driver` or `card->shortname` require this NUL-padding behavior
then `strscpy_pad` should be used. My interpretation, though, is that
the aforementioned fields are just fine as NUL-terminated strings.
Please correct my assumptions if needed and I'll send in a v2.
[1]: www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings
[2]: manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html
[3]: https://linux.die.net/man/3/strncpy
Link: https://github.com/KSPP/linux/issues/90
Link: https://lore.kernel.org/r/20230727-sound-xen-v1-1-89dd161351f1@google.com (related ALSA patch)
Signed-off-by: Justin Stitt <justinstitt@google.com>
Link: https://lore.kernel.org/r/20230727-sound-usb-bcd2000-v1-1-0dc73684b2f0@google.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
`strncpy` is deprecated for use on NUL-terminated destination strings [1].
A suitable replacement is `strscpy` [2] due to the fact that it
guarantees NUL-termination on its destination buffer argument which is
_not_ always the case for `strncpy`!
It should be noted that, in this case, the destination buffer has a
length strictly greater than the source string. Moreover, the source
string is NUL-terminated (and so is the destination) which means there
was no real bug happening here. Nonetheless, this patch would get us one
step closer to eliminating the `strncpy` API in the kernel, as its use
is too ambiguous. We need to favor less ambiguous replacements such as:
strscpy, strscpy_pad, strtomem and strtomem_pad (amongst others).
Technically, my patch yields subtly different behavior. The original
implementation with `strncpy` would fill the entire destination buffer
with null bytes [3] while `strscpy` will leave the junk, uninitialized
bytes trailing after the _mandatory_ NUL-termination. So, if somehow
`pcm->name` or `card->driver/shortname/longname` require this
NUL-padding behavior then `strscpy_pad` should be used. My
interpretation, though, is that the aforementioned fields are just fine
as NUL-terminated strings. Please correct my assumptions if needed and
I'll send in a v2.
[1]: www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings
[2]: manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html
[3]: https://linux.die.net/man/3/strncpy
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230727-sound-xen-v1-1-89dd161351f1@google.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.5
A collection of device specific fixes, none particularly remarkable.
There's a set of repetitive fixes for the RealTek drivers fixing an
issue with suspend that was replicated in multiple drivers.
|
|
Smatch complains that this return should be a goto:
sound/pci/hda/cs35l56_hda.c:910 cs35l56_hda_common_probe()
warn: missing unwind goto?
The goto error disables cansleep so that seems reasonable.
Fixes: 73cfbfa9caea ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/465160f4-b7cf-41d5-931e-d6c9e68fa3c7@moroto.mountain
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This laptop has CS35L41 amp connected via I2C.
With this patch speakers begin to work if the
missing _DSD properties are added to ACPI tables.
Signed-off-by: Pavel Asyutchenko <svenpavel@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230726223732.20775-1-svenpavel@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Maintenance patch for native DSD support.
Remove incorrect T+A device quirks. Move set of device quirks to vendor
quirks. Add set of missing device and vendor quirks.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Link: https://lore.kernel.org/r/20230726165645.404311-1-jussi@sonarnerd.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Microsoft Modern Wireless Headset (appearing on the host as "Microsoft
USB Link") has a playback and a capture mixer volume/switch, but they
are fairly broken. The descriptor reports wrong dB ranges for
playback, and the capture volume/switch don't influence on the actual
recording at all. Moreover, there seem instabilities in the
connection, and at best, we should disable the runtime PM.
So this ended up with a quirk entry for:
- Correct the playback dB range;
I picked up some reasonable values but it's a guess work
- Disable the capture mixer;
it's completely useless and confuses PA/PW
- Suppress get-sample-rate, apply the delay for message handling,
and suppress the auto-suspend
The behavior of the wheel control on the headset is somehow flaky,
too, but it's an issue of HID.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1207129
Link: https://lore.kernel.org/r/20230725092057.15115-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This HP Notebook used ALC236 codec with COEF 0x07 idx 1 controlling
the mute LED. Enable already existing quirk for this device.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230725111509.623773-1-l.guzenko@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.6
Here's an initial batch of updates for ASoC for this release cycle.
We've got a bunch of new drivers in here, a bit of core work from
Morimoto-san and quite a lot of janitorial work. There's several
updates that pull in changes from other subsystems in order to build
on them:
- An adaptor to allow use of IIO DACs and ADCs in ASoC which pulls in
some IIO changes.
- Create a library function for intlog10() and use it in the NAU8825
driver.
- Include the ASoC tests, including the topology tests, in the default
KUnit full test coverage. This also involves enabling UML builds of
ALSA since that's the default KUnit test environment which pulls in
the addition of some stubs to the driver.
- More factoring out from Morimoto-san.
- Convert a lot of drivers to use the more modern maple tree register
cache.
- Support for AMD machines with MAX98388 and NAU8821, Cirrus Logic
CS35L36, Intel AVS machines with ES8336 and RT5663 and NXP i.MX93.
|
|
The 8K sample parameter of 12.288Mhz main system bus clock doesn't work
because the I2SC_MR.IMCKDIV must not be 0 according to the sama5d2
series datasheet(I2SC Mode Register of Register Summary).
So use the 6.144Mhz instead of 12.288Mhz to support 8K sample.
Signed-off-by: Guiting Shen <aarongt.shen@gmail.com>
Link: https://lore.kernel.org/r/20230715030620.62328-1-aarongt.shen@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the system suspends, peripheral SDCA interrupts are disabled.
When system level resume is invoked, the peripheral SDCA interrupts
should be enabled to handle JD events.
Enable SDCA interrupts in resume sequence when ClockStop Mode0 is applied.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reported-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230721090711.128247-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the system suspends, peripheral Imp-defined interrupt is disabled.
When system level resume is invoked, the peripheral Imp-defined interrupts
should be enabled to handle JD events.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reported-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230721090654.128230-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the system suspends, peripheral SDCA interrupts are disabled.
When system level resume is invoked, the peripheral SDCA interrupts
should be enabled to handle JD events.
Enable SDCA interrupts in resume sequence when ClockStop Mode0 is applied.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reported-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230721090732.128282-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the system suspends, peripheral SDCA interrupts are disabled.
When system level resume is invoked, the peripheral SDCA interrupts
should be enabled to handle JD events.
Enable SDCA interrupts in resume sequence when ClockStop Mode0 is applied.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reported-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230721090721.128264-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to the datasheet, the DMIC config should
be changed to { 0, 2 ,3 }
Signed-off-by: Edgar <ljijcj@163.com>
Link: https://lore.kernel.org/r/20230719054722.401954-1-ljijcj@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the system suspends, peripheral Imp-defined interrupt is disabled.
When system level resume is invoked, the peripheral Imp-defined interrupts
should be enabled to handle JD events.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reported-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230721090643.128213-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The WM8904_ADC_TEST_0 register is modified as part of updating the OSR
controls but does not have a cache default, leading to errors when we try
to modify these controls in cache only mode with no prior read:
wm8904 3-001a: ASoC: error at snd_soc_component_update_bits on wm8904.3-001a for register: [0x000000c6] -16
Add a read of the register to probe() to fill the cache and avoid both the
error messages and the misconfiguration of the chip which will result.
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230723-asoc-fix-wm8904-adc-test-read-v1-1-2cdf2edd83fd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Dmytro Maluka <dmy@semihalf.com>:
This series includes 2 patches related to (but not fixing) the following
I2C failure which occurs sometimes during system suspend or resume and
indicates a problem with a spurious DA7219 interrupt:
[ 355.876211] i2c_designware i2c_designware.3: Transfer while suspended
[ 355.876245] WARNING: CPU: 2 PID: 3576 at drivers/i2c/busses/i2c-designware-master.c:570 i2c_dw_xfer+0x411/0x440
...
[ 355.876462] Call Trace:
[ 355.876468] <TASK>
[ 355.876475] ? update_load_avg+0x1b3/0x615
[ 355.876484] __i2c_transfer+0x101/0x1d8
[ 355.876494] i2c_transfer+0x74/0x10d
[ 355.876504] regmap_i2c_read+0x6a/0x9c
[ 355.876513] _regmap_raw_read+0x179/0x223
[ 355.876521] regmap_raw_read+0x1e1/0x28e
[ 355.876527] regmap_bulk_read+0x17d/0x1ba
[ 355.876532] ? __wake_up+0xed/0x1bb
[ 355.876542] da7219_aad_irq_thread+0x54/0x2c9 [snd_soc_da7219 5fb8ebb2179cf2fea29af090f3145d68ed8e2184]
[ 355.876556] irq_thread+0x13c/0x231
[ 355.876563] ? irq_forced_thread_fn+0x5f/0x5f
[ 355.876570] ? irq_thread_fn+0x4d/0x4d
[ 355.876576] kthread+0x13a/0x152
[ 355.876581] ? synchronize_irq+0xc3/0xc3
[ 355.876587] ? kthread_blkcg+0x31/0x31
[ 355.876592] ret_from_fork+0x1f/0x30
[ 355.876601] </TASK>
This log shows that DA7219 AAD interrupt handler da7219_aad_irq_thread()
is unexpectedly running when DA7219 is suspended and should not generate
interrupts. As a result, the IRQ handler is trying to read AAD IRQ event
status over I2C and is hitting the I2C driver "Transfer while suspended"
failure.
Patch #1 adds synchronize_irq() when suspending DA7219, to prevent the
IRQ handler from running after suspending if there is a pending IRQ
generated before suspending. With this patch the above failure is still
reproducible, so this patch does not fix any real observed issue so far,
but at least is useful for confirming that the above issue is not caused
by a pending IRQ but rather looks like a DA7219 hardware issue with an
unexpectedly generated IRQ.
Patch #2 does not fix the above issue either, but it prevents its
potentially harmful side effects. With the existing code, if the issue
occurs and the IRQ handler fails to read the AAD IRQ events status over
I2C, it does not check that and tries to use the garbage uninitialized
value of the events status, potentially reporting bogus events. This
patch fixes that by adding missing error checking.
In fact I'm sending these patches not only to submit them for review but
also to ask Renesas folks for any hints on a possible cause of the
described DA7219 issue (AAD interrupts spuriously firing after jack
detection is already disabled) or how to debug it further.
|
|
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
This set of patches adds support for using the CS35L56 boosted smart
amplifier on HDA systems. In these systems the CS35L56 audio is
routed through a HDA-to-I2S bridge codec.
This doesn't include the changes to the Realtek driver to actually hook
up the CS35L56 driver, because we don't yet have the QUIRK IDs to
associate it with. But we want to publish the driver now so that it is
available for bringing up hardware with the CS35L56.
The first 9 patches are moving code out of the ASoC driver and into the
shared library so that it can be shared with the HDA driver.
Patch #10 fixes missing #includes in the HDA headers so that the CS35L56
driver doesn't have to #include headers that it doesn't use.
|
|
Currently we only mute after playback has finished, and unmute
prior to setting global enable. To prevent any possible pops
and clicks, mute at probe, and then only unmute after global
enable is set.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-12-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To ensure consistency between the HDA core and the CS35L41 HDA
driver, add a device_link between them. This ensures that the
HDA core will suspend first, and resume second, meaning the
amp driver will not miss any events from the playback hook from
the HDA core during system suspend and resume.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-11-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In order to correctly pause audio on suspend, amps using external boost
require parts of the pause sequence to be called for all amps before moving
on to the next steps.
For example, as part of pausing the audio, the VSPK GPIO must be disabled,
but since this GPIO is controlled by one amp, but controls the boost for
all amps, it is required to separate the calls.
During playback this is achieved by using the pre and post playback hooks,
however during system suspend, this is not possible, so to separate the
calls, we use both the .prepare and .suspend calls to pause the audio.
Currently, for this reason, we do not restart audio on system resume.
However, we can support this by relying on the playback hook to resume
playback after system suspend.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-10-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use new hooks to ensure separation between play/pause actions,
as required by external boost.
External Boost on CS35L41 requires the amp to go through a
particular sequence of steps. One of these steps involes
the setting of a GPIO. This GPIO is connected to one or
more of the amps, and it may control the boost for all of
the amps. To ensure that the GPIO is set when it is safe
to do so, and to ensure that boost is ready for the rest of
the sequence to be able to continue, we must ensure that
the each part of the sequence is executed for each amp
before moving on to the next part of the sequence.
Some of the Play and Pause actions have moved from Open to
Prepare. This is because Open is not guaranteed to be called
again on system resume, whereas Prepare should.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-9-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
These hooks can be used to add callbacks that would be run before and after
the main playback hooks. These hooks would be called for all amps, before
moving on to the next hook, i.e. pre_playback_hook would be called for
all amps, before the playback_hook is called for all amps, then finally
the post_playback_hook is called for all amps.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-8-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This allows play and pause to be called from multiple places,
which is necessary for system suspend and resume.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-7-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are several steps required to put the system into system suspend.
Some of these steps may fail, so the driver should pass up the errors
if they occur.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-6-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In order to properly system suspend, it is necessary to unload the firmware
and ensure the chip is ready for shutdown (if necessary). If the system
is currently in runtime suspend, it is necessary to wake up the device,
and then make it ready. Currently, the wake does not correctly resync
the device, which may mean it cannot suspend correctly. Fix this by
performaing a resync.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-5-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently, we do not check the return status of the pause command,
immediately after we load firmware. If the pause has failed,
the firmware is not running.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To ensure the chip has correctly powered up or down before continuing,
the driver will now poll a register, rather than wait a fixed delay.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To enable the speaker output in external boost mode, 2 registers must
be set, one after another. The longer the time between the writes of
the two registers, the more likely, and more loudly a pop may occur.
To minimize this, an mbox command can be used to allow the firmware
to perform this action, minimizing any delay between write, thus
minimizing any pop or click as a result. The old method will remain
when running without firmware.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The LPASS macro drivers all acquire a number of clocks, but give no
indication when clk_get() fails, making it hard to identify and debug
system configuration issues. Make these drivers provide useful debug
information when this happens.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230721165027.2155528-1-quic_bjorande@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a driver for the Cirrus Logic CS35L56 amplifier. This uses the same
component binding API as the CS35L41 driver. This is not a standalone
HDA device; it provides control of the CS35L56 for systems that use a
combination of an HDA codec and CS35L56 amplifiers with audio routed
through the HDA codec.
The CS35L56 combines a high-performance mono audio amplifier, Class-H
tracking inductive boost converter, Halo Core(TM) DSP and a DC-DC boost
converter supporting Class-H tracking.
Control interfaces are I2C or SPI through the standard Linux I2C or SPI
bus framework.
Most chip functionality is controlled by on-board ROM firmware that is
always running. Firmware patches can be applied by the driver in the form
of a .wmfw file (firmware patch) and/or a .bin file (system tuning).
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230721132120.5523-12-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add #includes of dependencies into hda_auto_parser.h and hda_generic.h
hda_auto_parser.h uses definitions in hda_local.h.
hda_generic.h uses definitions in hda_local.h and hda_auto_parser.h.
It also references struct hda_jack_callback, but only as a pointer.
This has been forward-declared so hda_jack.h only needs to be
included in source that actually uses it.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230721132120.5523-11-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move issuing of a CS35L56_MBOX_CMD_SHUTDOWN command and then waiting for
the DSP to reach CS35L56_HALO_STATE_SHUTDOWN in the register appropriate
for the hardware revision into a common function.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-10-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move the waits for CS35L56_CONTROL_PORT_READY_US into a common
function, and also allow a wider range of allowed wait times.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-9-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Part of the initialization code in cs35l56_init() can be re-used
by the HDA driver so move it into a new function in the shared
library.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-8-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move the code that initialized the struct cs_dsp members
into the shared library so that the HDA driver can use it.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-7-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The majority of runtime_suspend and runtime_resume handling
doesn't have anything specific to the ASoC driver, so can be
shared by the HDA driver. Move this code into the shared
library.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move the cs35l56 utility functions into the shared file so they are
available for use in HDA.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the new cs35l56_base struct for utility functions.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The function can be more easily reused in HDA if the tracking of whether
a soft reset is being performed and whether the device is connected to a
SoundWire bus is moved out of the function.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ASoC and HDA drivers have structures that contain some of the same
information - instead of maintaining two locations for this data the
drivers should share a common data structure as this will enable common
utility functions to be created.
The first step is to move the location of these members in the ASoC
driver.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a quirk mechanism to allow specifying that active-high jack-detection
should be used on platforms where this info is not available in devicetree.
And add an entry for the Positivo CW14Q01P-V2 to the DMI table, so that
jack-detection will work properly on this laptop.
Signed-off-by: Edson Juliano Drosdeck <edson.drosdeck@gmail.com>
Link: https://lore.kernel.org/r/20230719200241.4865-1-edson.drosdeck@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When handling an AAD interrupt, if IRQ events read failed (for example,
due to i2c "Transfer while suspended" failure, i.e. when attempting to
read it while DA7219 is suspended, which may happen due to a spurious
AAD interrupt), the events array contains garbage uninitialized values.
So instead of trying to interprete those values and doing any actions
based on them (potentially resulting in misbehavior, e.g. reporting
bogus events), refuse to handle the interrupt.
Signed-off-by: Dmytro Maluka <dmy@semihalf.com>
Link: https://lore.kernel.org/r/20230717193737.161784-3-dmy@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
da7219_aad_suspend() disables jack detection, which should prevent
generating new interrupts by DA7219 while suspended. However, there is a
theoretical possibility that there is a pending interrupt generated just
before suspending DA7219 and not handled yet, so the IRQ handler may
still run after DA7219 is suspended. To prevent that, wait until the
pending IRQ handling is done.
This patch arose as an attempt to fix the following I2C failure
occurring sometimes during system suspend or resume:
[ 355.876211] i2c_designware i2c_designware.3: Transfer while suspended
[ 355.876245] WARNING: CPU: 2 PID: 3576 at drivers/i2c/busses/i2c-designware-master.c:570 i2c_dw_xfer+0x411/0x440
...
[ 355.876462] Call Trace:
[ 355.876468] <TASK>
[ 355.876475] ? update_load_avg+0x1b3/0x615
[ 355.876484] __i2c_transfer+0x101/0x1d8
[ 355.876494] i2c_transfer+0x74/0x10d
[ 355.876504] regmap_i2c_read+0x6a/0x9c
[ 355.876513] _regmap_raw_read+0x179/0x223
[ 355.876521] regmap_raw_read+0x1e1/0x28e
[ 355.876527] regmap_bulk_read+0x17d/0x1ba
[ 355.876532] ? __wake_up+0xed/0x1bb
[ 355.876542] da7219_aad_irq_thread+0x54/0x2c9 [snd_soc_da7219 5fb8ebb2179cf2fea29af090f3145d68ed8e2184]
[ 355.876556] irq_thread+0x13c/0x231
[ 355.876563] ? irq_forced_thread_fn+0x5f/0x5f
[ 355.876570] ? irq_thread_fn+0x4d/0x4d
[ 355.876576] kthread+0x13a/0x152
[ 355.876581] ? synchronize_irq+0xc3/0xc3
[ 355.876587] ? kthread_blkcg+0x31/0x31
[ 355.876592] ret_from_fork+0x1f/0x30
[ 355.876601] </TASK>
which indicates that the AAD IRQ handler is unexpectedly running when
DA7219 is suspended, and as a result, is trying to read data from DA7219
over I2C and is hitting the I2C driver "Transfer while suspended"
failure.
However, with this patch the above failure is still reproducible. So
this patch does not fix any real observed issue so far, but at least is
useful for confirming that the above issue is not caused by a pending
IRQ but rather looks like a DA7219 hardware issue with an IRQ
unexpectedly generated after jack detection is already disabled.
Signed-off-by: Dmytro Maluka <dmy@semihalf.com>
Link: https://lore.kernel.org/r/20230717193737.161784-2-dmy@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There's several things here that will really help my CI.
|
