| Age | Commit message (Collapse) | Author |
|---|
|
On second and subsequent passes through quiescent-state forcing, the
isidle variable was initialized to false, which would prevent full sysidle
state from being reached if a grace period needed more than one round
of quiescent-state forcing (which most should not). However, the check
for offline CPUs in the quiescent-state forcing main loop had the wrong
sense, which could prevent CPUs from ever entering full sysidle state.
This commit fixes both of these bugs. Given that sysidle is not yet
wired up, this has no effect in old kernels, but might have proven
frustrating had anyone attempted to wire it up.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
The "if" statement at the beginning of rcu_torture_writer() should
use the same set of variables. In theory, this does not matter because
the corresponding variables (gp_sync and gp_sync1) have the same value
at this point in the code, but in practice such puzzles should be
removed. This commit therefore makes the use of variables consistent.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
This commit adds a CONFIG_RCU_EXPEDITE_BOOT Kconfig parameter
that emulates a very early boot rcu_expedite_gp(). A late-boot
call to rcu_end_inkernel_boot() will provide the corresponding
rcu_unexpedite_gp(). The late-boot call to rcu_end_inkernel_boot()
should be made just before init is spawned.
According to Arjan:
> To show the boot time, I'm using the timestamp of the "Write protecting"
> line, that's pretty much the last thing we print prior to ring 3 execution.
>
> A kernel with default RCU behavior (inside KVM, only virtual devices)
> looks like this:
>
> [ 0.038724] Write protecting the kernel read-only data: 10240k
>
> a kernel with expedited RCU (using the command line option, so that I
> don't have to recompile between measurements and thus am completely
> oranges-to-oranges)
>
> [ 0.031768] Write protecting the kernel read-only data: 10240k
>
> which, in percentage, is an 18% improvement.
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Arjan van de Ven <arjan@linux.intel.com>
|
|
This commit updates open-coded tests of the rcu_expedited variable
to instead use rcu_gp_is_expedited().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
Currently, expediting of normal synchronous grace-period primitives
(synchronize_rcu() and friends) is controlled by the rcu_expedited()
boot/sysfs parameter. This works well, but does not handle nesting.
This commit therefore provides rcu_expedite_gp() to enable expediting
and rcu_unexpedite_gp() to cancel a prior rcu_expedite_gp(), both of
which support nesting.
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
When a CPU comes online, it initializes its callback list. This
is a bad thing if this is the first time that the CPU has come
online and if that CPU has early boot callbacks. This commit therefore
avoid initializing the callback list if there are callbacks present,
in which case the initial call_rcu() did the initialization for us.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
Some diagnostics under CONFIG_PROVE_RCU in rcu_nocb_cpu_needs_barrier()
assume that there can be no early-boot callbacks. This commit therefore
qualifies the diagnostic with rcu_scheduler_fully_active to permit
early boot callbacks to avoid this splat.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
Currently, a call_rcu() that precedes rcu_init() will splat due to the
callback lists not having yet been initialized. This commit causes the
first such callback to initialize the boot CPU's RCU callback list.
Note that this commit does not change rcu_init()-time initialization,
which means that the callback will be discarded at rcu_init() time.
Fixing this is the job of later commits.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
This commit wires up the rcu_state structures' ->rda pointers to the
per-CPU rcu_data structures at compile time, thus ensuring that this
linkage is present at early boot, in turn allowing posting of callbacks
before rcu_init() is executed.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
In preparation for early-boot posting of callbacks, this commit abstracts
initialization of the default (non-no-CB) callbacks list from the
init_callback_list() function into a new init_default_callback_list()
function.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In rcu_gp_init(), rnp->completed equals to rsp->completed in THEORY,
we don't need to touch it normally. If something goes wrong,
it will complain and fixup rnp->completed and avoid oops.
This commit thus avoids the normal needless store to rnp->completed.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
There are currently duplicate identical definitions of the
rcu_synchronize() structure and the wakeme_after_rcu() function.
Thie commit therefore consolidates them.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
When CONFIG_PM_DEBUG=y, we provide a sysfs file (/sys/power/pm_test) for
selecting one of a few suspend test modes, where rather than entering a
full suspend state, the kernel will perform some subset of suspend
steps, wait 5 seconds, and then resume back to normal operation.
This mode is useful for (among other things) observing the state of the
system just before entering a sleep mode, for debugging or analysis
purposes. However, a constant 5 second wait is not sufficient for some
sorts of analysis; for example, on an SoC, one might want to use
external tools to probe the power states of various on-chip controllers
or clocks.
This patch turns this 5 second delay into a configurable module
parameter, so users can determine how long to wait in this
pseudo-suspend state before resuming the system.
Example (wait 30 seconds);
# echo 30 > /sys/module/suspend/parameters/pm_test_delay
# echo core > /sys/power/pm_test
# time echo mem > /sys/power/state
...
[ 17.583625] suspend debug: Waiting for 30 second(s).
...
real 0m30.381s
user 0m0.017s
sys 0m0.080s
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add support for task events as well as system-wide events. This change
has a big impact on the way that we gather LLC occupancy values in
intel_cqm_event_read().
Currently, for system-wide (per-cpu) events we defer processing to
userspace which knows how to discard all but one cpu result per package.
Things aren't so simple for task events because we need to do the value
aggregation ourselves. To do this, we defer updating the LLC occupancy
value in event->count from intel_cqm_event_read() and do an SMP
cross-call to read values for all packages in intel_cqm_event_count().
We need to ensure that we only do this for one task event per cache
group, otherwise we'll report duplicate values.
If we're a system-wide event we want to fallback to the default
perf_event_count() implementation. Refactor this into a common function
so that we don't duplicate the code.
Also, introduce PERF_TYPE_INTEL_CQM, since we need a way to track an
event's task (if the event isn't per-cpu) inside of the Intel CQM PMU
driver. This task information is only availble in the upper layers of
the perf infrastructure.
Other perf backends stash the target task in event->hw.*target so we
need to do something similar. The task is used to determine whether
events should share a cache group and an RMID.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kanaka Juvva <kanaka.d.juvva@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Cc: linux-api@vger.kernel.org
Link: http://lkml.kernel.org/r/1422038748-21397-8-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The Intel QoS PMU needs to know whether an event is part of a cgroup
during ->event_init(), because tasks in the same cgroup share a
monitoring ID.
Move the cgroup initialisation before calling into the PMU driver.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kanaka Juvva <kanaka.d.juvva@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Link: http://lkml.kernel.org/r/1422038748-21397-4-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
For PMU drivers that record per-package counters, the ->count variable
cannot be used to record an accurate aggregated value, since it's not
possible to perform SMP cross-calls to cpus on other packages from the
context in which we update ->count.
Introduce a new optional ->count() accessor function that can be used to
customize how values are collected. If a PMU driver doesn't provide a
->count() function, we fallback to the existing code.
There is necessarily a window of staleness with this approach because
the task that generated the counter value may not have been scheduled by
the cpu recently.
An alternative and more complex approach would be to use a hrtimer to
periodically refresh the values from a more permissive scheduling
context. So, we're trading off complexity for accuracy.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kanaka Juvva <kanaka.d.juvva@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Link: http://lkml.kernel.org/r/1422038748-21397-3-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Move perf_cgroup_from_task() from kernel/events/ to include/linux/ along
with the necessary struct definitions, so that it can be used by the PMU
code.
When the upcoming Intel Cache Monitoring PMU driver assigns monitoring
IDs to perf events, it needs to be able to check whether any two
monitoring events overlap (say, a cgroup and task event), which means we
need to be able to lookup the cgroup associated with a task (if any).
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kanaka Juvva <kanaka.d.juvva@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Link: http://lkml.kernel.org/r/1422038748-21397-2-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching
Pull livepatching fixes from Jiri Kosina:
"Two tiny fixes for livepatching infrastructure:
- extending RCU critical section to cover all accessess to
RCU-protected variable, by Petr Mladek
- proper format string passing to kobject_init_and_add(), by Jiri
Kosina"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: RCU protect struct klp_func all the time when used in klp_ftrace_handler()
livepatch: fix format string in kobject_init_and_add()
|
|
With the new standardized functions, we can replace all
ACCESS_ONCE() calls across relevant locking - this includes
lockref and seqlock while at it.
ACCESS_ONCE() does not work reliably on non-scalar types.
For example gcc 4.6 and 4.7 might remove the volatile tag
for such accesses during the SRA (scalar replacement of
aggregates) step:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=58145
Update the new calls regardless of if it is a scalar type,
this is cleaner than having three alternatives.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1424662301.6539.18.camel@stgolabs.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
new changes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The mm->exe_file is currently serialized with mmap_sem (shared)
in order to both safely (1) read the file and (2) audit it via
audit_log_d_path(). Good users will, on the other hand, make use
of the more standard get_mm_exe_file(), requiring only holding
the mmap_sem to read the value, and relying on reference counting
to make sure that the exe file won't dissapear underneath us.
Additionally, upon NULL return of get_mm_exe_file, we also call
audit_log_format(ab, " exe=(null)").
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
[PM: tweaked subject line]
Signed-off-by: Paul Moore <pmoore@redhat.com>
|
|
This patch adds a audit_log_d_path_exe() helper function
to share how we handle auditing of the exe_file's path.
Used by both audit and auditsc. No functionality is changed.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
[PM: tweaked subject line]
Signed-off-by: Paul Moore <pmoore@redhat.com>
|
|
Fixed a coding style issue (unnecessary parentheses , unnecessary braces)
Signed-off-by: Ameen-Ali <Ameenali023@gmail.com>
[PM: tweaked subject line]
Signed-off-by: Paul Moore <pmoore@redhat.com>
|
|
During a queue overflow condition while we are waiting for auditd to drain the
queue to make room for regular messages, we don't want a successful auditd that
has bypassed the queue check to reset the backlog wait time.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
|
|
Copy the set wait time to a working value to avoid losing the set
value if the queue overflows.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
|
|
When file auditing is enabled, during a low memory situation, a memory
allocation with __GFP_FS can lead to pruning the inode cache. Which can,
in turn lead to audit_tree_freeing_mark() being called. This can call
audit_schedule_prune(), that tries to fork a pruning thread, and
waits until the thread is created. But forking needs memory, and the
memory allocations there are done with __GFP_FS.
So we are waiting merrily for some __GFP_FS memory allocations to complete,
while holding some filesystem locks. This can take a while ...
This patch creates a single thread for pruning the tree from
audit_add_tree_rule(), and thus avoids the deadlock that the on-demand
thread creation can cause.
Reported-by: Matt Wilson <msw@amazon.com>
Cc: Matt Wilson <msw@amazon.com>
Signed-off-by: Imre Palik <imrep@amazon.de>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
|
|
klp_ftrace_handler()
func->new_func has been accessed after rcu_read_unlock() in klp_ftrace_handler()
and therefore the access was not protected.
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS:
- a number of fixes that didn't make the 3.19 release.
- a number of cleanups.
- preliminary support for Cavium's Octeon 3 SOCs which feature up to
48 MIPS64 R3 cores with FPU and hardware virtualization.
- support for MIPS R6 processors.
Revision 6 of the MIPS architecture is a major revision of the MIPS
architecture which does away with many of original sins of the
architecture such as branch delay slots. This and other changes in
R6 require major changes throughout the entire MIPS core
architecture code and make up for the lion share of this pull
request.
- finally some preparatory work for eXtendend Physical Address
support, which allows support of up to 40 bit of physical address
space on 32 bit processors"
[ Ahh, MIPS can't leave the PAE brain damage alone. It's like
every CPU architect has to make that mistake, but pee in the snow
by changing the TLA. But whether it's called PAE, LPAE or XPA,
it's horrid crud - Linus ]
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits)
MIPS: sead3: Corrected get_c0_perfcount_int
MIPS: mm: Remove dead macro definitions
MIPS: OCTEON: irq: add CIB and other fixes
MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs.
MIPS: OCTEON: More OCTEONIII support
MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits.
MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup.
MIPS: OCTEON: Update octeon-model.h code for new SoCs.
MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX
MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h
MIPS: OCTEON: Implement the core-16057 workaround
MIPS: OCTEON: Delete unused COP2 saving code
MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register
MIPS: OCTEON: Save and restore CP2 SHA3 state
MIPS: OCTEON: Fix FP context save.
MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs
MIPS: boot: Provide more uImage options
MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h
MIPS: ip22-gio: Remove legacy suspend/resume support
mips: pci: Add ifdef around pci_proc_domain
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull ntp fix from Ingo Molnar:
"An adjtimex interface regression fix for 32-bit systems"
[ A check that was added in a previous commit is really only a concern
for 64bit systems, but was applied to both 32 and 64bit systems, which
results in breaking 32bit systems.
Thus the fix here is to make the check only apply to 64bit systems ]
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ntp: Fixup adjtimex freq validation on 32-bit systems
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"Two fixes: the paravirt spin_unlock() corruption/crash fix, and an
rtmutex NULL dereference crash fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/spinlocks/paravirt: Fix memory corruption on unlock
locking/rtmutex: Avoid a NULL pointer dereference on deadlock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Thiscontains misc fixes: preempt_schedule_common() and io_schedule()
recursion fixes, sched/dl fixes, a completion_done() revert, two
sched/rt fixes and a comment update patch"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/rt: Avoid obvious configuration fail
sched/autogroup: Fix failure to set cpu.rt_runtime_us
sched/dl: Do update_rq_clock() in yield_task_dl()
sched: Prevent recursion in io_schedule()
sched/completion: Serialize completion_done() with complete()
sched: Fix preempt_schedule_common() triggering tracing recursion
sched/dl: Prevent enqueue of a sleeping task in dl_task_timer()
sched: Make dl_task_time() use task_rq_lock()
sched: Clarify ordering between task_rq_lock() and move_queued_task()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull rcu fix and x86 irq fix from Ingo Molnar:
- Fix a bug that caused an RCU warning splat.
- Two x86 irq related fixes: a hotplug crash fix and an ACPI IRQ
registry fix.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Clear need_qs flag to prevent splat
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Check for valid irq descriptor in check_irq_vectors_for_cpu_disable()
x86/irq: Fix regression caused by commit b568b8601f05
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull kgdb/kdb updates from Jason Wessel:
"KGDB/KDB New:
- KDB: improved searching
- No longer enter debug core on panic if panic timeout is set
KGDB/KDB regressions / cleanups
- fix pdf doc build errors
- prevent junk characters on kdb console from printk levels"
* tag 'for_linux-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kgdb, docs: Fix <para> pdfdocs build errors
debug: prevent entering debug mode on panic/exception.
kdb: Const qualifier for kdb_getstr's prompt argument
kdb: Provide forward search at more prompt
kdb: Fix a prompt management bug when using | grep
kdb: Remove stack dump when entering kgdb due to NMI
kdb: Avoid printing KERN_ levels to consoles
kdb: Fix off by one error in kdb_cpu()
kdb: fix incorrect counts in KDB summary command output
|
|
On non-developer devices, kgdb prevents the device from rebooting
after a panic.
Incase of panics and exceptions, to allow the device to reboot, prevent
entering debug mode to avoid getting stuck waiting for the user to
interact with debugger.
To avoid entering the debugger on panic/exception without any extra
configuration, panic_timeout is being used which can be set via
/proc/sys/kernel/panic at run time and CONFIG_PANIC_TIMEOUT sets the
default value.
Setting panic_timeout indicates that the user requested machine to
perform unattended reboot after panic. We dont want to get stuck waiting
for the user input incase of panic.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: kgdb-bugreport@lists.sourceforge.net
Cc: linux-kernel@vger.kernel.org
Cc: Android Kernel Team <kernel-team@android.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Colin Cross <ccross@android.com>
[Kiran: Added context to commit message.
panic_timeout is used instead of break_on_panic and
break_on_exception to honor CONFIG_PANIC_TIMEOUT
Modified the commit as per community feedback]
Signed-off-by: Kiran Raparthy <kiran.kumar@linaro.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
All current callers of kdb_getstr() can pass constant pointers via the
prompt argument. This patch adds a const qualification to make explicit
the fact that this is safe.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
Currently kdb allows the output of comamnds to be filtered using the
| grep feature. This is useful but does not permit the output emitted
shortly after a string match to be examined without wading through the
entire unfiltered output of the command. Such a feature is particularly
useful to navigate function traces because these traces often have a
useful trigger string *before* the point of interest.
This patch reuses the existing filtering logic to introduce a simple
forward search to kdb that can be triggered from the more prompt.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
Currently when the "| grep" feature is used to filter the output of a
command then the prompt is not displayed for the subsequent command.
Likewise any characters typed by the user are also not echoed to the
display. This rather disconcerting problem eventually corrects itself
when the user presses Enter and the kdb_grepping_flag is cleared as
kdb_parse() tries to make sense of whatever they typed.
This patch resolves the problem by moving the clearing of this flag
from the middle of command processing to the beginning.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
Issuing a stack dump feels ergonomically wrong when entering due to NMI.
Entering due to NMI is normally a reaction to a user request, either the
NMI button on a server or a "magic knock" on a UART. Therefore the
backtrace behaviour on entry due to NMI should be like SysRq-g (no stack
dump) rather than like oops.
Note also that the stack dump does not offer any information that
cannot be trivial retrieved using the 'bt' command.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
Currently when kdb traps printk messages then the raw log level prefix
(consisting of '\001' followed by a numeral) does not get stripped off
before the message is issued to the various I/O handlers supported by
kdb. This causes annoying visual noise as well as causing problems
grepping for ^. It is also a change of behaviour compared to normal usage
of printk() usage. For example <SysRq>-h ends up with different output to
that of kdb's "sr h".
This patch addresses the problem by stripping log levels from messages
before they are issued to the I/O handlers. printk() which can also
act as an i/o handler in some cases is special cased; if the caller
provided a log level then the prefix will be preserved when sent to
printk().
The addition of non-printable characters to the output of kdb commands is a
regression, albeit and extremely elderly one, introduced by commit
04d2c8c83d0e ("printk: convert the format for KERN_<LEVEL> to a 2 byte
pattern"). Note also that this patch does *not* restore the original
behaviour from v3.5. Instead it makes printk() from within a kdb command
display the message without any prefix (i.e. like printk() normally does).
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Joe Perches <joe@perches.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
There was a follow on replacement patch against the prior
"kgdb: Timeout if secondary CPUs ignore the roundup".
See: https://lkml.org/lkml/2015/1/7/442
This patch is the delta vs the patch that was committed upstream:
* Fix an off-by-one error in kdb_cpu().
* Replace NR_CPUS with CONFIG_NR_CPUS to tell checkpatch that we
really want a static limit.
* Removed the "KGDB: " prefix from the pr_crit() in debug_core.c
(kgdb-next contains a patch which introduced pr_fmt() to this file
to the tag will now be applied automatically).
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
The output of KDB 'summary' command should report MemTotal, MemFree
and Buffers output in kB. Current codes report in unit of pages.
A define of K(x) as
is defined in the code, but not used.
This patch would apply the define to convert the values to kB.
Please include me on Cc on replies. I do not subscribe to linux-kernel.
Signed-off-by: Jay Lan <jlan@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
- several cleanups in kbuild
- serialize multiple *config targets so that 'make defconfig kvmconfig'
works
- The cc-ifversion macro got support for an else-branch
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild,gcov: simplify kernel/gcov/Makefile more
kbuild: allow cc-ifversion to have the argument for false condition
kbuild,gcov: simplify kernel/gcov/Makefile
kbuild,gcov: remove unnecessary workaround
kbuild: do not add $(call ...) to invoke cc-version or cc-fullversion
kbuild: fix cc-ifversion macro
kbuild: drop $(version_h) from MRPROPER_FILES
kbuild: use mixed-targets when two or more config targets are given
kbuild: remove redundant line from bounds.h/asm-offsets.h
kbuild: merge bounds.h and asm-offsets.h rules
kbuild: Drop support for clean-rule
|
|
If registering the function with ftrace has previously succeeded,
unregistering will almost never fail. Even if it does, it's not a fatal
error. We can still carry on and disable the klp_func from being used
by removing it from the klp_ops func stack.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Petr Mladek <pmladek@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
User visible changes:
- No need to explicitely enable evsels for workload started from perf, let it
be enabled via perf_event_attr.enable_on_exec, removing some events that take
place in the 'perf trace' before a workload is really started by it.
(Arnaldo Carvalho de Melo)
- Fix to handle optimized not-inlined functions in 'perf probe' (Masami Hiramatsu)
- Update 'perf probe' man page (Masami Hiramatsu)
- 'perf trace': Allow mixing with tracepoints and suppressing plain syscalls
(Arnaldo Carvalho de Melo)
Infrastructure changes:
- Introduce {trace_seq_do,event_format_}_fprintf functions to allow
a default tracepoint field list printer to be used in tools that allows
redirecting output to a file. (Arnaldo Carvalho de Melo)
- The man page for pthread_attr_set_affinity_np states that _GNU_SOURCE
must be defined before pthread.h, do it to fix the build in some
systems (Josh Boyer)
- Cleanups in 'perf buildid-cache' (Masami Hiramatsu)
- Fix dso cache test case (Namhyung Kim)
- Do Not rely on dso__data_read_offset() to open DSO (Namhyung Kim)
- Make perf aware of tracefs (Steven Rostedt).
- Fix build by defining STT_GNU_IFUNC for glibc 2.9 and older (Vinson Lee)
- AArch64 symbol resolution fixes (Victor Kamensky)
- Kconfig beachhead (Jiri Olsa)
- Simplify nr_pages validity (Kaixu Xia)
- Fixup header positioning in 'perf list' (Yunlong Song)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If the CPU is running a realtime task that does not round-robin
with another realtime task of equal priority, there is no point
in keeping the scheduler tick going. After all, whenever the
scheduler tick runs, the kernel will just decide not to
reschedule.
Extend sched_can_stop_tick() to recognize these situations, and
inform the rest of the kernel that the scheduler tick can be
stopped.
Tested-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: fweisbec@redhat.com
Cc: mtosatti@redhat.com
Link: http://lkml.kernel.org/r/20150216152349.6a8ed824@annuminas.surriel.com
[ Small cleanliness tweak. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu into core/urgent
Pull RCU fix from Paul E. McKenney.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Use event->attr.branch_sample_type to replace
intel_pmu_needs_lbr_smpl() for avoiding duplicated code that
implicitly enables the LBR.
Currently, branch stack can be enabled by user explicitly requesting
branch sampling or implicit branch sampling to correct PEBS skid.
For user explicitly requested branch sampling, the branch_sample_type
is explicitly set by user. For PEBS case, the branch_sample_type is also
implicitly set to PERF_SAMPLE_BRANCH_ANY in x86_pmu_hw_config.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: eranian@google.com
Cc: jolsa@redhat.com
Link: http://lkml.kernel.org/r/1415156173-10035-11-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
