| Age | Commit message (Collapse) | Author |
|---|
|
Add SO_TIMESTAMP_NEW and SO_TIMESTAMPNS_NEW variants of
socket timestamp options.
These are the y2038 safe versions of the SO_TIMESTAMP_OLD
and SO_TIMESTAMPNS_OLD for all architectures.
Note that the format of scm_timestamping.ts[0] is not changed
in this patch.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Cc: jejb@parisc-linux.org
Cc: ralf@linux-mips.org
Cc: rth@twiddle.net
Cc: linux-alpha@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If driver did not fill the fw_version field, try to call into
the new devlink get_info op and collect the versions that way.
We assume ethtool was always reporting running versions.
v4:
- use IS_REACHABLE() to avoid problems with DEVLINK=m (kbuildbot).
v3 (Jiri):
- do a dump and then parse it instead of special handling;
- concatenate all versions (well, all that fit :)).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add defines and docs for generic info versions.
v3:
- add docs;
- separate patch (Jiri).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ethtool -i has a few fixed-size fields which can be used to report
firmware version and expansion ROM version. Unfortunately, modern
hardware has more firmware components. There is usually some
datapath microcode, management controller, PXE drivers, and a
CPLD load. Running ethtool -i on modern controllers reveals the
fact that vendors cram multiple values into firmware version field.
Here are some examples from systems I could lay my hands on quickly:
tg3: "FFV20.2.17 bc 5720-v1.39"
i40e: "6.01 0x800034a4 1.1747.0"
nfp: "0.0.3.5 0.25 sriov-2.1.16 nic"
Add a new devlink API to allow retrieving multiple versions, and
provide user-readable name for those versions.
While at it break down the versions into three categories:
- fixed - this is the board/fixed component version, usually vendors
report information like the board version in the PCI VPD,
but it will benefit from naming and common API as well;
- running - this is the running firmware version;
- stored - this is firmware in the flash, after firmware update
this value will reflect the flashed version, while the
running version may only be updated after reboot.
v3:
- add per-type helpers instead of using the special argument (Jiri).
RFCv2:
- remove the nesting in attr DEVLINK_ATTR_INFO_VERSIONS (now
versions are mixed with other info attrs)l
- have the driver report versions from the same callback as
other info.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ethtool -i has served us well for a long time, but its showing
its limitations more and more. The device information should
also be reported per device not per-netdev.
Lay foundation for a simple devlink-based way of reading device
info. Add driver name and device serial number as initial pieces
of information exposed via this new API.
v3:
- rename helpers (Jiri);
- rename driver name attr (Jiri);
- remove double spacing in commit message (Jiri).
RFC v2:
- wrap the skb into an opaque structure (Jiri);
- allow the serial number of be any length (Jiri & Andrew);
- add driver name (Jonathan).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we don't zerocopy if the crypto framework async bit is set.
However some crypto algorithms (such as x86 AESNI) support async,
but in the context of sendmsg, will never run asynchronously. Instead,
check for actual EINPROGRESS return code before assuming algorithm is
async.
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS 1.3 has minor changes from TLS 1.2 at the record layer.
* Header now hardcodes the same version and application content type in
the header.
* The real content type is appended after the data, before encryption (or
after decryption).
* The IV is xored with the sequence number, instead of concatinating four
bytes of IV with the explicit IV.
* Zero-padding: No exlicit length is given, we search backwards from the
end of the decrypted data for the first non-zero byte, which is the
content type. Currently recv supports reading zero-padding, but there
is no way for send to add zero padding.
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS 1.3 has a different AAD size, use a variable in the code to
make TLS 1.3 support easy.
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wire up support for 256 bit keys from the setsockopt to the crypto
framework
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the missing and malformed documentation that kernel-doc and
sphinx warn about. While at it, also add some things to the docs
to fix missing links.
Sadly, the only way I could find to fix this was to add some
trailing whitespace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add the missing documentation that kernel-doc continually warns
about, to get rid of all that noise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In typical cases, there's no need to pass both the maxattr
and the policy array pointer, as the maxattr should just be
ARRAY_SIZE(policy) - 1. Therefore, to be less error prone,
just remove the maxattr argument from the default macros
and deduce the size accordingly.
Leave the original macros with a leading underscore to use
here and in case somebody needs to pass a policy pointer
where the policy isn't declared in the same place and thus
ARRAY_SIZE() cannot be used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Merge net-next so that we get the changes from net, which would
otherwise conflict with the NLA_POLICY_NESTED/_ARRAY changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix spelling mistake in cfg80211.h: "lenght" -> "length".
The typo is also in the special comment block which
translates to documentation.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There was a typo in the documentation for weight_multiplier in mac80211.h,
and the doc was missing entirely for airtime and airtime_weight in sta_info.h.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
While implementing ipvlan l3 and l3s mode for kubernetes CNI plugin,
I ran into the issue that while l3 mode is working fine, l3s mode
does not have any connectivity to kube-apiserver and hence all pods
end up in Error state as well. The ipvlan master device sits on
top of a bond device and hostns traffic to kube-apiserver (also running
in hostns) is DNATed from 10.152.183.1:443 to 139.178.29.207:37573
where the latter is the address of the bond0. While in l3 mode, a
curl to https://10.152.183.1:443 or to https://139.178.29.207:37573
works fine from hostns, neither of them do in case of l3s. In the
latter only a curl to https://127.0.0.1:37573 appeared to work where
for local addresses of bond0 I saw kernel suddenly starting to emit
ARP requests to query HW address of bond0 which remained unanswered
and neighbor entries in INCOMPLETE state. These ARP requests only
happen while in l3s.
Debugging this further, I found the issue is that l3s mode is piggy-
backing on l3 master device, and in this case local routes are using
l3mdev_master_dev_rcu(dev) instead of net->loopback_dev as per commit
f5a0aab84b74 ("net: ipv4: dst for local input routes should use l3mdev
if relevant") and 5f02ce24c269 ("net: l3mdev: Allow the l3mdev to be
a loopback"). I found that reverting them back into using the
net->loopback_dev fixed ipvlan l3s connectivity and got everything
working for the CNI.
Now judging from 4fbae7d83c98 ("ipvlan: Introduce l3s mode") and the
l3mdev paper in [0] the only sole reason why ipvlan l3s is relying
on l3 master device is to get the l3mdev_ip_rcv() receive hook for
setting the dst entry of the input route without adding its own
ipvlan specific hacks into the receive path, however, any l3 domain
semantics beyond just that are breaking l3s operation. Note that
ipvlan also has the ability to dynamically switch its internal
operation from l3 to l3s for all ports via ipvlan_set_port_mode()
at runtime. In any case, l3 vs l3s soley distinguishes itself by
'de-confusing' netfilter through switching skb->dev to ipvlan slave
device late in NF_INET_LOCAL_IN before handing the skb to L4.
Minimal fix taken here is to add a IFF_L3MDEV_RX_HANDLER flag which,
if set from ipvlan setup, gets us only the wanted l3mdev_l3_rcv() hook
without any additional l3mdev semantics on top. This should also have
minimal impact since dev->priv_flags is already hot in cache. With
this set, l3s mode is working fine and I also get things like
masquerading pod traffic on the ipvlan master properly working.
[0] https://netdevconf.org/1.2/papers/ahern-what-is-l3mdev-paper.pdf
Fixes: f5a0aab84b74 ("net: ipv4: dst for local input routes should use l3mdev if relevant")
Fixes: 5f02ce24c269 ("net: l3mdev: Allow the l3mdev to be a loopback")
Fixes: 4fbae7d83c98 ("ipvlan: Introduce l3s mode")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: David Ahern <dsa@cumulusnetworks.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Martynas Pumputis <m@lambda.lt>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sockopt
Check with SCTP_ALL_ASSOC instead in sctp_setsockopt_scheduler and
check with SCTP_FUTURE_ASSOC instead in sctp_getsockopt_scheduler,
it's compatible with 0.
SCTP_CURRENT_ASSOC is supported for SCTP_STREAM_SCHEDULER in this
patch. It also adds default_ss in sctp_sock to support
SCTP_FUTURE_ASSOC.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check with SCTP_FUTURE_ASSOC instead in
sctp_set/getsockopt_paddr_thresholds, it's compatible with 0.
It also adds pf_retrans in sctp_sock to support SCTP_FUTURE_ASSOC.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
wake_on_lan - Enables Wake on Lan for this port. If enabled,
the controller asserts a wake pin based on the WOL type.
v2->v3:
- Define only WOL types used now and define them as bitfield, so that
mutliple WOL types can be enabled upon power on.
- Modify "wake-on-lan" name to "wake_on_lan" to be symmetric with
previous definitions.
- Rename DEVLINK_PARAM_WOL_XXX to DEVLINK_PARAM_WAKE_XXX to be
symmetrical with ethtool WOL definitions.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add notification call for devlink port param set, register and unregister
functions.
Add devlink_port_param_value_changed() function to enable the driver notify
devlink on value change. Driver should use this function after value was
changed on any configuration mode part to driverinit.
v7->v8:
Order devlink_port_param_value_changed() definitions followed by
devlink_param_value_changed()
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for "driverinit" configuration mode value for devlink_port
configuration parameters. Add devlink_port_param_driverinit_value_set()
function to help the driver set the value to devlink_port.
Also, move the common code to __devlink_param_driverinit_value_set()
to be used by both device and port params.
v7->v8:
Re-order the definitions as follows:
__devlink_param_driverinit_value_get
__devlink_param_driverinit_value_set
devlink_param_driverinit_value_get
devlink_param_driverinit_value_set
devlink_port_param_driverinit_value_get
devlink_port_param_driverinit_value_set
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for "driverinit" configuration mode value for devlink_port
configuration parameters. Add devlink_port_param_driverinit_value_get()
function to help the driver get the value from devlink_port.
Also, move the common code to __devlink_param_driverinit_value_get()
to be used by both device and port params.
v7->v8:
-Add the missing devlink_port_param_driverinit_value_get() declaration.
-Also, order devlink_port_param_driverinit_value_get() after
devlink_param_driverinit_value_get/set() calls
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add functions to register and unregister for the driver supported
configuration parameters table per port.
v7->v8:
- Order the definitions following way as suggested by Jiri.
__devlink_params_register
__devlink_params_unregister
devlink_params_register
devlink_params_unregister
devlink_port_params_register
devlink_port_params_unregister
- Append with Acked-by: Jiri Pirko <jiri@mellanox.com>.
v2->v3:
- Add a helper __devlink_params_register() with common code used by
both devlink_params_register() and devlink_port_params_register().
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
aead_request_set_crypt takes an iv pointer, and we change the iv
soon after setting it. Some async crypto algorithms don't save the iv,
so we need to save it in the tls_rec for async requests.
Found by hardcoding x64 aesni to use async crypto manager (to test the async
codepath), however I don't think this combination can happen in the wild.
Presumably other hardware offloads will need this fix, but there have been
no user reports.
Fixes: a42055e8d2c30 ("Add support for async encryption of records...")
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-01-29
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Teach verifier dead code removal, this also allows for optimizing /
removing conditional branches around dead code and to shrink the
resulting image. Code store constrained architectures like nfp would
have hard time doing this at JIT level, from Jakub.
2) Add JMP32 instructions to BPF ISA in order to allow for optimizing
code generation for 32-bit sub-registers. Evaluation shows that this
can result in code reduction of ~5-20% compared to 64 bit-only code
generation. Also add implementation for most JITs, from Jiong.
3) Add support for __int128 types in BTF which is also needed for
vmlinux's BTF conversion to work, from Yonghong.
4) Add a new command to bpftool in order to dump a list of BPF-related
parameters from the system or for a specific network device e.g. in
terms of available prog/map types or helper functions, from Quentin.
5) Add AF_XDP sock_diag interface for querying sockets from user
space which provides information about the RX/TX/fill/completion
rings, umem, memory usage etc, from Björn.
6) Add skb context access for skb_shared_info->gso_segs field, from Eric.
7) Add support for testing flow dissector BPF programs by extending
existing BPF_PROG_TEST_RUN infrastructure, from Stanislav.
8) Split BPF kselftest's test_verifier into various subgroups of tests
in order better deal with merge conflicts in this area, from Jakub.
9) Add support for queue/stack manipulations in bpftool, from Stanislav.
10) Document BTF, from Yonghong.
11) Dump supported ELF section names in libbpf on program load
failure, from Taeung.
12) Silence a false positive compiler warning in verifier's BTF
handling, from Peter.
13) Fix help string in bpftool's feature probing, from Prashant.
14) Remove duplicate includes in BPF kselftests, from Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next tree:
1) Introduce a hashtable to speed up object lookups, from Florian Westphal.
2) Make direct calls to built-in extension, also from Florian.
3) Call helper before confirming the conntrack as it used to be originally,
from Florian.
4) Call request_module() to autoload br_netfilter when physdev is used
to relax the dependency, also from Florian.
5) Allow to insert rules at a given position ID that is internal to the
batch, from Phil Sutter.
6) Several patches to replace conntrack indirections by direct calls,
and to reduce modularization, from Florian. This also includes
several follow up patches to deal with minor fallout from this
rework.
7) Use RCU from conntrack gre helper, from Florian.
8) GRE conntrack module becomes built-in into nf_conntrack, from Florian.
9) Replace nf_ct_invert_tuplepr() by calls to nf_ct_invert_tuple(),
from Florian.
10) Unify sysctl handling at the core of nf_conntrack, from Florian.
11) Provide modparam to register conntrack hooks.
12) Allow to match on the interface kind string, from wenxu.
13) Remove several exported symbols, not required anymore now after
a bit of de-modulatization work has been done, from Florian.
14) Remove built-in map support in the hash extension, this can be
done with the existing userspace infrastructure, from laura.
15) Remove indirection to calculate checksums in IPVS, from Matteo Croce.
16) Use call wrappers for indirection in IPVS, also from Matteo.
17) Remove superfluous __percpu parameter in nft_counter, patch from
Luc Van Oostenryck.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function pointer ip_vs_protocol->csum_check is only used in protocol
specific code, and never in the generic one.
Remove the function pointer from struct ip_vs_protocol and call the
checksum functions directly.
This reduces the performance impact of the Spectre mitigation, and
should give a small improvement even with RETPOLINES disabled.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In order to be more confident about an on-going interactive session, we
increment pingpong count by 1 for every interactive transaction and we
adjust TCP_PINGPONG_THRESH to 3.
This means, we only consider a session in pingpong mode after we see 3
interactive transactions, and start to activate delayed acks in quick
ack mode.
And in order to not over-count the credits, we only increase pingpong
count for the first packet sent in response for the previous received
packet.
This is mainly to prevent delaying the ack immediately after some
handshake protocol but no real interactive traffic pattern afterwards.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using pingpong as a single bit information, we refactor the
code to treat it as a counter. When interactive session is detected,
we set pingpong count to TCP_PINGPONG_THRESH. And when pingpong count
is >= TCP_PINGPONG_THRESH, we consider the session in pingpong mode.
This patch is a pure refactor and sets foundation for the next patch.
This patch itself does not change any pingpong logic.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Add tnl_update_pmtu in ip_md_tunnel_xmit to dynamic modify
the pmtu which packet send through collect_metadata mode
ip tunnel
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Accept MSG_ZEROCOPY in all the TCP states that allow sendmsg. Remove
the explicit check for ESTABLISHED and CLOSE_WAIT states.
This requires correctly handling zerocopy state (uarg, sk_zckey) in
all paths reachable from other TCP states. Such as the EPIPE case
in sk_stream_wait_connect, which a sendmsg() in incorrect state will
now hit. Most paths are already safe.
Only extension needed is for TCP Fastopen active open. This can build
an skb with data in tcp_send_syn_data. Pass the uarg along with other
fastopen state, so that this skb also generates a zerocopy
notification on release.
Tested with active and passive tcp fastopen packetdrill scripts at
https://github.com/wdebruij/packetdrill/commit/1747eef03d25a2404e8132817d0f1244fd6f129d
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, IPv6 defragmentation code drops non-last fragments that
are smaller than 1280 bytes: see
commit 0ed4229b08c1 ("ipv6: defrag: drop non-last frags smaller than min mtu")
This behavior is not specified in IPv6 RFCs and appears to break
compatibility with some IPv6 implemenations, as reported here:
https://www.spinics.net/lists/netdev/msg543846.html
This patch re-uses common IP defragmentation queueing and reassembly
code in IPv6, removing the 1280 byte restriction.
Signed-off-by: Peter Oskolkov <posk@google.com>
Reported-by: Tom Herbert <tom@herbertland.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a refactoring patch: without changing runtime behavior,
it moves rbtree-related code from IPv4-specific files/functions
into .h/.c defrag files shared with IPv6 defragmentation code.
Signed-off-by: Peter Oskolkov <posk@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 40cbfa90218b ("cfg80211/nl80211: Optional authentication
offload to userspace")' introduced authentication offload to user
space by the host drivers in station mode. This commit extends
the same for the AP mode too.
Extend NL80211_ATTR_EXTERNAL_AUTH_SUPPORT to also claim the
support of external authentication from the user space in AP mode.
A new flag parameter is introduced in cfg80211_ap_settings to
intend the same while "start ap".
Host driver to use NL80211_CMD_FRAME interface to transmit and
receive the authentication frames to / from the user space.
Host driver to indicate the flag NL80211_RXMGMT_FLAG_EXTERNAL_AUTH
while sending the authentication frame to the user space. This
intends to the user space that the driver wishes it to process
the authentication frame for certain protocols, though it had
initially advertised the support for SME functionality.
User space shall accordingly do the authentication and indicate
its final status through the command NL80211_CMD_EXTERNAL_AUTH.
Allow the command even if userspace doesn't include the attribute
NL80211_ATTR_SSID for AP interface.
Host driver shall continue with the association sequence and
indicate the STA connection status through cfg80211_new_sta.
To facilitate the host drivers in AP mode for matching the pmkid
by the stations during the association, NL80211_CMD_EXTERNAL_AUTH
is also enhanced to include the pmkid to drivers after
the authentication.
This pmkid can also be used in the STA mode to include in the
association request.
Also modify nl80211_external_auth to not mandate SSID in AP mode.
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
[remove useless nla_get_flag() usage]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This reverts the devlink health changes from 9/17/2019,
Jiri wants things to be designed differently and it was
agreed that the easiest way to do this is start from the
beginning again.
Commits reverted:
cb5ccfbe73b389470e1dc11061bb185ef4bc9aec
880ee82f0313453ec5a6cb122866ac057263066b
c7af343b4e33578b7de91786a3f639c8cfa0d97b
ff253fedab961b22117a73ab808fcfa9e6852b50
6f9d56132eb6d2603d4273cfc65bed914ec47acb
fcd852c69d776c0f46c8f79e8e431e5cc6ddc7b7
8a66704a13d9713593342e29b4f0c19762f5746b
12bd0dcefe88782ac1c9fff632958dd1b71d27e5
aba25279c10094c5c97d09c3491ca86d00b4ad5e
ce019faa70f81555fa17ebc1d5a03651f2e7e15a
b8c45a033acc607201588f7665ba84207e5149e0
And the follow-on build fix:
o33a0efa4baecd689da9474ce0e8b673eb6931c60
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There was no such capability advertisement from the driver and thus the
current user space has to assume the driver to support all the AKMs. While
that may be the case with some drivers (e.g., mac80211-based ones), there
are cfg80211-based drivers that implement SME and have constraints on
which AKMs can be supported (e.g., such drivers may need an update to
support SAE AKM using NL80211_CMD_EXTERNAL_AUTH). Allow such drivers to
advertise the exact set of supported AKMs so that user space tools can
determine what network profile options should be allowed to be configured.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
[pmsr data might be big, start a new netlink message section]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since we reworked ieee80211_return_txq() so it assumes that the caller
takes care of logging, we need another function that can be called without
holding any locks. Introduce ieee80211_schedule_txq() which serves this
purpose.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a hook to allow the BT driver to do device or command specific
handling in case of timeouts. This is to be used by Intel driver to
reset the device after certain number of timeouts.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Aggregation effects are extremely common with wifi, cellular, and cable
modem link technologies, ACK decimation in middleboxes, and LRO and GRO
in receiving hosts. The aggregation can happen in either direction,
data or ACKs, but in either case the aggregation effect is visible
to the sender in the ACK stream.
Previously BBR's sending was often limited by cwnd under severe ACK
aggregation/decimation because BBR sized the cwnd at 2*BDP. If packets
were acked in bursts after long delays (e.g. one ACK acking 5*BDP after
5*RTT), BBR's sending was halted after sending 2*BDP over 2*RTT, leaving
the bottleneck idle for potentially long periods. Note that loss-based
congestion control does not have this issue because when facing
aggregation it continues increasing cwnd after bursts of ACKs, growing
cwnd until the buffer is full.
To achieve good throughput in the presence of aggregation effects, this
algorithm allows the BBR sender to put extra data in flight to keep the
bottleneck utilized during silences in the ACK stream that it has evidence
to suggest were caused by aggregation.
A summary of the algorithm: when a burst of packets are acked by a
stretched ACK or a burst of ACKs or both, BBR first estimates the expected
amount of data that should have been acked, based on its estimated
bandwidth. Then the surplus ("extra_acked") is recorded in a windowed-max
filter to estimate the recent level of observed ACK aggregation. Then cwnd
is increased by the ACK aggregation estimate. The larger cwnd avoids BBR
being cwnd-limited in the face of ACK silences that recent history suggests
were caused by aggregation. As a sanity check, the ACK aggregation degree
is upper-bounded by the cwnd (at the time of measurement) and a global max
of BW * 100ms. The algorithm is further described by the following
presentation:
https://datatracker.ietf.org/meeting/101/materials/slides-101-iccrg-an-update-on-bbr-work-at-google-00
In our internal testing, we observed a significant increase in BBR
throughput (measured using netperf), in a basic wifi setup.
- Host1 (sender on ethernet) -> AP -> Host2 (receiver on wifi)
- 2.4 GHz -> BBR before: ~73 Mbps; BBR after: ~102 Mbps; CUBIC: ~100 Mbps
- 5.0 GHz -> BBR before: ~362 Mbps; BBR after: ~593 Mbps; CUBIC: ~601 Mbps
Also, this code is running globally on YouTube TCP connections and produced
significant bandwidth increases for YouTube traffic.
This is based on Ian Swett's max_ack_height_ algorithm from the
QUIC BBR implementation.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I made a dumb mistake when I summed up the slave stats, obviously slaves
can come and go which would make the master stats unreliable.
Count and export the master stats separately.
Fixes: a258aeacd7f0 ("bonding: add support for xstats and export 3ad stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds an id to the umem structure. The id uniquely
identifies a umem instance, and will be exposed to user-space via the
socket monitoring interface.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Track each AF_XDP socket in a per-netns list. This will be used later
by the sock_diag interface for querying sockets from userspace.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
syzbot found that ax25 routes where not properly protected
against concurrent use [1].
In this particular report the bug happened while
copying ax25->digipeat.
Fix this problem by making sure we call ax25_get_route()
while ax25_route_lock is held, so that no modification
could happen while using the route.
The current two ax25_get_route() callers do not sleep,
so this change should be fine.
Once we do that, ax25_get_route() no longer needs to
grab a reference on the found route.
[1]
ax25_connect(): syz-executor0 uses autobind, please contact jreuter@yaina.de
BUG: KASAN: use-after-free in memcpy include/linux/string.h:352 [inline]
BUG: KASAN: use-after-free in kmemdup+0x42/0x60 mm/util.c:113
Read of size 66 at addr ffff888066641a80 by task syz-executor2/531
ax25_connect(): syz-executor0 uses autobind, please contact jreuter@yaina.de
CPU: 1 PID: 531 Comm: syz-executor2 Not tainted 5.0.0-rc2+ #10
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1db/0x2d0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
check_memory_region_inline mm/kasan/generic.c:185 [inline]
check_memory_region+0x123/0x190 mm/kasan/generic.c:191
memcpy+0x24/0x50 mm/kasan/common.c:130
memcpy include/linux/string.h:352 [inline]
kmemdup+0x42/0x60 mm/util.c:113
kmemdup include/linux/string.h:425 [inline]
ax25_rt_autobind+0x25d/0x750 net/ax25/ax25_route.c:424
ax25_connect.cold+0x30/0xa4 net/ax25/af_ax25.c:1224
__sys_connect+0x357/0x490 net/socket.c:1664
__do_sys_connect net/socket.c:1675 [inline]
__se_sys_connect net/socket.c:1672 [inline]
__x64_sys_connect+0x73/0xb0 net/socket.c:1672
do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x458099
Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f870ee22c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000458099
RDX: 0000000000000048 RSI: 0000000020000080 RDI: 0000000000000005
RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000
ax25_connect(): syz-executor4 uses autobind, please contact jreuter@yaina.de
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f870ee236d4
R13: 00000000004be48e R14: 00000000004ce9a8 R15: 00000000ffffffff
Allocated by task 526:
save_stack+0x45/0xd0 mm/kasan/common.c:73
set_track mm/kasan/common.c:85 [inline]
__kasan_kmalloc mm/kasan/common.c:496 [inline]
__kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:469
kasan_kmalloc+0x9/0x10 mm/kasan/common.c:504
ax25_connect(): syz-executor5 uses autobind, please contact jreuter@yaina.de
kmem_cache_alloc_trace+0x151/0x760 mm/slab.c:3609
kmalloc include/linux/slab.h:545 [inline]
ax25_rt_add net/ax25/ax25_route.c:95 [inline]
ax25_rt_ioctl+0x3b9/0x1270 net/ax25/ax25_route.c:233
ax25_ioctl+0x322/0x10b0 net/ax25/af_ax25.c:1763
sock_do_ioctl+0xe2/0x400 net/socket.c:950
sock_ioctl+0x32f/0x6c0 net/socket.c:1074
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0x107b/0x17d0 fs/ioctl.c:696
ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
ax25_connect(): syz-executor5 uses autobind, please contact jreuter@yaina.de
Freed by task 550:
save_stack+0x45/0xd0 mm/kasan/common.c:73
set_track mm/kasan/common.c:85 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/common.c:458
kasan_slab_free+0xe/0x10 mm/kasan/common.c:466
__cache_free mm/slab.c:3487 [inline]
kfree+0xcf/0x230 mm/slab.c:3806
ax25_rt_add net/ax25/ax25_route.c:92 [inline]
ax25_rt_ioctl+0x304/0x1270 net/ax25/ax25_route.c:233
ax25_ioctl+0x322/0x10b0 net/ax25/af_ax25.c:1763
sock_do_ioctl+0xe2/0x400 net/socket.c:950
sock_ioctl+0x32f/0x6c0 net/socket.c:1074
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0x107b/0x17d0 fs/ioctl.c:696
ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff888066641a80
which belongs to the cache kmalloc-96 of size 96
The buggy address is located 0 bytes inside of
96-byte region [ffff888066641a80, ffff888066641ae0)
The buggy address belongs to the page:
page:ffffea0001999040 count:1 mapcount:0 mapping:ffff88812c3f04c0 index:0x0
flags: 0x1fffc0000000200(slab)
ax25_connect(): syz-executor4 uses autobind, please contact jreuter@yaina.de
raw: 01fffc0000000200 ffffea0001817948 ffffea0002341dc8 ffff88812c3f04c0
raw: 0000000000000000 ffff888066641000 0000000100000020 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888066641980: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
ffff888066641a00: 00 00 00 00 00 00 00 00 02 fc fc fc fc fc fc fc
>ffff888066641a80: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
^
ffff888066641b00: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
ffff888066641b80: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When multiple multicast routers are present in a broadcast domain then
only one of them will be detectable via IGMP/MLD query snooping. The
multicast router with the lowest IP address will become the selected and
active querier while all other multicast routers will then refrain from
sending queries.
To detect such rather silent multicast routers, too, RFC4286
("Multicast Router Discovery") provides a standardized protocol to
detect multicast routers for multicast snooping switches.
This patch implements the necessary MRD Advertisement message parsing
and after successful processing adds such routers to the internal
multicast router list.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch refactors ip_mc_check_igmp(), ipv6_mc_check_mld() and
their callers (more precisely, the Linux bridge) to not rely on
the skb_trimmed parameter anymore.
An skb with its tail trimmed to the IP packet length was initially
introduced for the following three reasons:
1) To be able to verify the ICMPv6 checksum.
2) To be able to distinguish the version of an IGMP or MLD query.
They are distinguishable only by their size.
3) To avoid parsing data for an IGMPv3 or MLDv2 report that is
beyond the IP packet but still within the skb.
The first case still uses a cloned and potentially trimmed skb to
verfiy. However, there is no need to propagate it to the caller.
For the second and third case explicit IP packet length checks were
added.
This hopefully makes ip_mc_check_igmp() and ipv6_mc_check_mld() easier
to read and verfiy, as well as easier to use.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for extended statistics (xstats) call to the
bonding. The first user would be the 3ad code which counts the following
events:
- LACPDU Rx/Tx
- LACPDU unknown type Rx
- LACPDU illegal Rx
- Marker Rx/Tx
- Marker response Rx/Tx
- Marker unknown type Rx
All of these are exported via netlink as separate attributes to be
easily extensible as we plan to add more in the future.
Similar to how the bridge and other xstats exports, the structure
inside is:
[ IFLA_STATS_LINK_XSTATS ]
-> [ LINK_XSTATS_TYPE_BOND ]
-> [ BOND_XSTATS_3AD ]
-> [ 3ad stats attributes ]
With this structure it's easy to add more stat types later.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Count the following types of 3ad packets per slave:
- rx/tx lacpdu
- rx/tx marker
- rx/tx marker response
- rx illegal lacpdus (right now counted on wrong length)
- rx unknown lacpdu type
- rx unknown marker type
The counters are using atomic64 since this is not fast path.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With commit e16337622016 ("Bluetooth: Handle bt_accept_enqueue() socket
atomically") lock_sock[_nested]() is used to acquire the socket lock
before manipulating the socket. lock_sock[_nested]() may block, which
is problematic since bt_accept_enqueue() can be called in bottom half
context (e.g. from rfcomm_connect_ind()):
[<ffffff80080d81ec>] __might_sleep+0x4c/0x80
[<ffffff800876c7b0>] lock_sock_nested+0x24/0x58
[<ffffff8000d7c27c>] bt_accept_enqueue+0x48/0xd4 [bluetooth]
[<ffffff8000e67d8c>] rfcomm_connect_ind+0x190/0x218 [rfcomm]
Add a parameter to bt_accept_enqueue() to indicate whether the
function is called from BH context, and acquire the socket lock
with bh_lock_sock_nested() if that's the case.
Also adapt all callers of bt_accept_enqueue() to pass the new
parameter:
- l2cap_sock_new_connection_cb()
- uses lock_sock() to lock the parent socket => process context
- rfcomm_connect_ind()
- acquires the parent socket lock with bh_lock_sock() => BH
context
- __sco_chan_add()
- called from sco_chan_add(), which is called from sco_connect().
parent is NULL, hence bt_accept_enqueue() isn't called in this
code path and we can ignore it
- also called from sco_conn_ready(). uses bh_lock_sock() to acquire
the parent lock => BH context
Fixes: e16337622016 ("Bluetooth: Handle bt_accept_enqueue() socket atomically")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
|
