| Age | Commit message (Collapse) | Author |
|---|
|
When tag_set->nr_maps is 1, the block layer limits the number of hw queues
by nr_cpu_ids. No matter how many hw queues are used by virtio-scsi, as it
has (tag_set->nr_maps == 1), it can use at most nr_cpu_ids hw queues.
In addition, specifically for pci scenario, when the 'num_queues' specified
by qemu is more than maxcpus, virtio-scsi would not be able to allocate
more than maxcpus vectors in order to have a vector for each queue. As a
result, it falls back into MSI-X with one vector for config and one shared
for queues.
Considering above reasons, this patch limits the number of hw queues used
by virtio-scsi by nr_cpu_ids.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When tag_set->nr_maps is 1, the block layer limits the number of hw queues
by nr_cpu_ids. No matter how many hw queues are used by virtio-blk, as it
has (tag_set->nr_maps == 1), it can use at most nr_cpu_ids hw queues.
In addition, specifically for pci scenario, when the 'num-queues' specified
by qemu is more than maxcpus, virtio-blk would not be able to allocate more
than maxcpus vectors in order to have a vector for each queue. As a result,
it falls back into MSI-X with one vector for config and one shared for
queues.
Considering above reasons, this patch limits the number of hw queues used
by virtio-blk by nr_cpu_ids.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Badly-designed systems might have (for example) active-high wake pins
that default to high (e.g., because of external pull ups) until they
have an active firmware which starts driving it low. This can cause an
interrupt storm in the time between request_irq() and disable_irq().
We don't support shared interrupts here, so let's just pre-configure the
interrupt to avoid auto-enabling it.
Fixes: fd913ef7ce61 ("Bluetooth: btusb: Add out-of-band wakeup support")
Fixes: 5364a0b4f4be ("arm64: dts: rockchip: move QCA6174A wakeup pin into its USB node")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the third step to make MT2701 HDMI stable.
We should not change the rate of parent for hdmi phy when
doing round_rate for this clock. The parent clock of hdmi
phy must be the same as it. We change it when doing set_rate
only.
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
This is the second step to make MT2701 HDMI stable.
The factor depends on the divider of DPI in MT2701, therefore,
we should fix this factor to the right and new one.
Test: search ok
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
This is the first step to make MT2701 hdmi stable.
The parent rate of hdmi phy had set by DPI driver.
We should not set or change the parent rate of MT2701 hdmi phy,
as a result we should remove the flags of "CLK_SET_RATE_PARENT"
from the clock of MT2701 hdmi phy.
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
Recalculate the rate of this clock, by querying hardware to
make implementation of recalc_rate() to match the definition.
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
Due to a clerical error,there is one zero less for 12800000.
Fix it for 128000000
Fixes: 0fc721b2968e ("drm/mediatek: add hdmi driver for MT2701 and MT7623")
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
ACPICA commit b233720031a480abd438f2e9c643080929d144c3
ASL operation_regions declare a range of addresses that it uses. In a
perfect world, the range of addresses should be used exclusively by
the AML interpreter. The OS can use this information to decide which
drivers to load so that the AML interpreter and device drivers use
different regions of memory.
During table load, the address information is added to a global
address range list. Each node in this list contains an address range
as well as a namespace node of the operation_region. This list is
deleted at ACPI shutdown.
Unfortunately, ASL operation_regions can be declared inside of control
methods. Although this is not recommended, modern firmware contains
such code. New module level code changes unintentionally removed the
functionality of adding and removing nodes to the global address
range list.
A few months ago, support for adding addresses has been re-
implemented. However, the removal of the address range list was
missed and resulted in some systems to crash due to the address list
containing bogus namespace nodes from operation_regions declared in
control methods. In order to fix the crash, this change removes
dynamic operation_regions after control method termination.
Link: https://github.com/acpica/acpica/commit/b2337200
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202475
Fixes: 4abb951b73ff ("ACPICA: AML interpreter: add region addresses in global list during initialization")
Reported-by: Michael J Gruber <mjg@fedoraproject.org>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Cc: 4.20+ <stable@vger.kernel.org> # 4.20+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/gpu/drm/mediatek/mtk_hdmi.c:1521:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1509, but without a corresponding object release within this function.
drivers/gpu/drm/mediatek/mtk_hdmi.c:1524:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1509, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
Push getting the reference for the encoders' power domains into the
encoder get_power_domains() hook instead of doing this from the caller.
This way the encoder can store away the corresponding wakerefs.
This fixes the DSI encoder disabling, which didn't release these
power references it acquired during HW state readout.
Note that longtime ownership for the corresponding wakerefs can be thus
acquired / released in two ways. Nevertheless there is always only one
owner for them:
After HW readout (booting/system resume):
- encoder->get_power_domains() acquires
- encoder->disable*() releases
After a modeset (calling intel_atomic_commit()):
- encoder->enable*() acquires
- encoder->disable*() releases
* can be any of the encoder enable/disable hooks.
v2:
- Check that the DSI io_wakerefs are unset both during encoder HW
readout and enabling. (Chris)
Fixes: 0e6e0be4c9523 ("drm/i915: Markup paired operations on display power domains")
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190407124655.31536-1-imre.deak@intel.com
(cherry picked from commit 3a52fb7e7953f0b13df8c05d0d74b56a66888f30)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Pull networking fixes from David Miller:
1) Off by one and bounds checking fixes in NFC, from Dan Carpenter.
2) There have been many weird regressions in r8169 since we turned ASPM
support on, some are still not understood nor completely resolved.
Let's turn this back off for now. From Heiner Kallweit.
3) Signess fixes for ethtool speed value handling, from Michael
Zhivich.
4) Handle timestamps properly in macb driver, from Paul Thomas.
5) Two erspan fixes, it's the usual "skb ->data potentially reallocated
and we're holding a stale protocol header pointer". From Lorenzo
Bianconi.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bnxt_en: Reset device on RX buffer errors.
bnxt_en: Improve RX consumer index validity check.
net: macb driver, check for SKBTX_HW_TSTAMP
qlogic: qlcnic: fix use of SPEED_UNKNOWN ethtool constant
broadcom: tg3: fix use of SPEED_UNKNOWN ethtool constant
ethtool: avoid signed-unsigned comparison in ethtool_validate_speed()
net: ip6_gre: fix possible use-after-free in ip6erspan_rcv
net: ip_gre: fix possible use-after-free in erspan_rcv
r8169: disable ASPM again
MAINTAINERS: ieee802154: update documentation file pattern
net: vrf: Fix ping failed when vrf mtu is set to 0
selftests: add a tc matchall test case
nfc: nci: Potential off by one in ->pipes[] array
NFC: nci: Add some bounds checking in nci_hci_cmd_received()
|
|
If scsi cmd sglist is not suitable for DDP then csiostor driver uses
preallocated buffers for DDP, because of this data copy is required from
DDP buffer to scsi cmd sglist before calling ->scsi_done().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If the RX completion indicates RX buffers errors, the RX ring will be
disabled by firmware and no packets will be received on that ring from
that point on. Recover by resetting the device.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is logic to check that the RX/TPA consumer index is the expected
index to work around a hardware problem. However, the potentially bad
consumer index is first used to index into an array to reference an entry.
This can potentially crash if the bad consumer index is beyond legal
range. Improve the logic to use the consumer index for dereferencing
after the validity check and log an error message.
Fixes: fa7e28127a5a ("bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure SKBTX_HW_TSTAMP (i.e. SOF_TIMESTAMPING_TX_HARDWARE) has been
enabled for this skb. It does fix the issue where normal socks that
aren't expecting a timestamp will not wake up on select, but when a
user does want a SOF_TIMESTAMPING_TX_HARDWARE it does work.
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qlcnic driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.
For example, the following test will print "False":
u16 speed = SPEED_UNKNOWN;
if (speed == SPEED_UNKNOWN)
printf("True");
else
printf("False");
Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3 driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.
For example, the following test will print "False":
u16 speed = SPEED_UNKNOWN;
if (speed == SPEED_UNKNOWN)
printf("True");
else
printf("False");
Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
calc_tpm2_event_size() has an invalid signature because
it returns a 'size_t' where as its signature says that
it returns 'int'.
Cc: <stable@vger.kernel.org>
Fixes: 4d23cc323cdb ("tpm: add securityfs support for TPM 2.0 firmware event log")
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
The poll condition should only check response_length,
because reads should only be issued if there is data to read.
The response_read flag only prevents double writes.
The problem was that the write set the response_read to false,
enqued a tpm job, and returned. Then application called poll
which checked the response_read flag and returned EPOLLIN.
Then the application called read, but got nothing.
After all that the async_work kicked in.
Added also mutex_lock around the poll check to prevent
other possible race conditions.
Fixes: 9488585b21bef0df12 ("tpm: add support for partial reads")
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Tested-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
tpm_chip_start/stop() should be also called for TPM 1.x devices on
suspend. Add that functionality back. Do not lock the chip because
it is unnecessary as there are no multiple threads using it when
doing the suspend.
Fixes: a3fbfae82b4c ("tpm: take TPM chip power gating out of tpm_transmit()")
Reported-by: Paul Zimmerman <pauldzim@gmail.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
There's a significant number of reports that re-enabling ASPM causes
different issues, ranging from decreased performance to system not
booting at all. This affects only a minority of users, but the number
of affected users is big enough that we better switch off ASPM again.
This will hurt notebook users who are not affected by the issues, they
may see decreased battery runtime w/o ASPM. With the PCI core folks is
being discussed to add generic sysfs attributes to control ASPM.
Once this is in place brave enough users can re-enable ASPM on their
system.
Fixes: a99790bf5c7f ("r8169: Reinstate ASPM Support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vring_create_virtqueue() allows the caller to specify via the
may_reduce_num parameter whether the vring code is allowed to
allocate a smaller ring than specified.
However, the split ring allocation code tries to allocate a
smaller ring on allocation failure regardless of what the
caller specified. This may cause trouble for e.g. virtio-pci
in legacy mode, which does not support ring resizing. (The
packed ring code does not resize in any case.)
Let's fix this by bailing out immediately in the split ring code
if the requested size cannot be allocated and may_reduce_num has
not been specified.
While at it, fix a typo in the usage instructions.
Fixes: 2a2d1382fe9d ("virtio: Add improved queue allocation API")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
|
|
The method of hem free for SCC context is different from qp context.
In the current version, if free SCC hem during the execution of qp free,
there may be smmu error as below:
arm-smmu-v3 arm-smmu-v3.1.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.1.auto: 0x00007d0000000010
arm-smmu-v3 arm-smmu-v3.1.auto: 0x000012000000017c
arm-smmu-v3 arm-smmu-v3.1.auto: 0x00000000000009e0
arm-smmu-v3 arm-smmu-v3.1.auto: 0x0000000000000000
As SCC context is still used by hardware after qp free, we can solve this
problem by removing SCC hem free from hns_roce_qp_free.
Fixes: 6a157f7d1b14 ("RDMA/hns: Add SCC context allocation support for hip08")
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Due to the incorrect use of the seg and obj information, the position of
the mtt is calculated incorrectly, and the free space of the page is not
enough to store the entire mtt, resulting in access to the next page. This
patch fixes this problem.
Unable to handle kernel paging request at virtual address ffff00006e3cd000
...
Call trace:
hns_roce_write_mtt+0x154/0x2f0 [hns_roce]
hns_roce_buf_write_mtt+0xa8/0xd8 [hns_roce]
hns_roce_create_srq+0x74c/0x808 [hns_roce]
ib_create_srq+0x28/0xc8
Fixes: 0203b14c4f32 ("RDMA/hns: Unify the calculation for hem index in hip08")
Signed-off-by: chenglang <chenglang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Make sure to free the DSR on pvrdma_pci_remove() to avoid the memory leak.
Fixes: 29c8d9eba550 ("IB: Add vmw_pvrdma driver")
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Acked-by: Adit Ranadive <aditr@vmware.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The only bpc information in pipe registers for BXT/GLK DSI
is the PIPEMISC dither bpc. Let's try to use that to read
out pipe_bpp on these platforms. However, I'm not sure if
this will be correctly populated by the GOP since bspec
suggests it's only needed if dithering is actually enabled.
If not I guess we'll have to go one step further and
extract pipe_bpp from the DSI pixel format when dithering
is disabled.
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: ca0b04db14a5 ("drm/i915/dsi: Fix pipe_bpp for handling for 6 bpc pixel-formats")
References: https://bugs.freedesktop.org/show_bug.cgi?id=109516
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405141349.11950-1-ville.syrjala@linux.intel.com
(cherry picked from commit 499653501baf27d26e73cb5ce744869df3400509)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
[Why]
If the cursor pos passed from DM is less than the plane_state->dst_rect
top left corner then the unsigned cursor pos wraps around to a large
positive number since cursor pos is a u32.
There was an attempt to guard against this in hubp1_cursor_set_position
by checking the src_x_offset and src_y_offset and offseting the
cursor hotspot within hubp1_cursor_set_position.
However, the cursor position itself is still being programmed
incorrectly as a large value.
This manifests itself visually as the cursor disappearing or containing
strange artifacts near the middle of the screen on raven.
[How]
Don't subtract the destination rect top left corner from the pos but
add it to the hotspot instead. This happens before the pos gets
passed into hubp1_cursor_set_position.
This achieves the same result but avoids the subtraction wrap around.
With this fix the original cursor programming logic can be used again.
v2: add hunk that got dropped accidently when this patch was originally
committed. (Alex)
Fixes: 0921c41e1902831 ("drm/amd/display: Fix negative cursor pos programming")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Murton Liu <Murton.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If the msix_affinity_masks is alloced failed, then we'll
try to free some resources in vp_free_vectors() that may
access it directly.
We met the following stack in our production:
[ 29.296767] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 29.311151] IP: [<ffffffffc04fe35a>] vp_free_vectors+0x6a/0x150 [virtio_pci]
[ 29.324787] PGD 0
[ 29.333224] Oops: 0000 [#1] SMP
[...]
[ 29.425175] RIP: 0010:[<ffffffffc04fe35a>] [<ffffffffc04fe35a>] vp_free_vectors+0x6a/0x150 [virtio_pci]
[ 29.441405] RSP: 0018:ffff9a55c2dcfa10 EFLAGS: 00010206
[ 29.453491] RAX: 0000000000000000 RBX: ffff9a55c322c400 RCX: 0000000000000000
[ 29.467488] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9a55c322c400
[ 29.481461] RBP: ffff9a55c2dcfa20 R08: 0000000000000000 R09: ffffc1b6806ff020
[ 29.495427] R10: 0000000000000e95 R11: 0000000000aaaaaa R12: 0000000000000000
[ 29.509414] R13: 0000000000010000 R14: ffff9a55bd2d9e98 R15: ffff9a55c322c400
[ 29.523407] FS: 00007fdcba69f8c0(0000) GS:ffff9a55c2840000(0000) knlGS:0000000000000000
[ 29.538472] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 29.551621] CR2: 0000000000000000 CR3: 000000003ce52000 CR4: 00000000003607a0
[ 29.565886] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 29.580055] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 29.594122] Call Trace:
[ 29.603446] [<ffffffffc04fe8a2>] vp_request_msix_vectors+0xe2/0x260 [virtio_pci]
[ 29.618017] [<ffffffffc04fedc5>] vp_try_to_find_vqs+0x95/0x3b0 [virtio_pci]
[ 29.632152] [<ffffffffc04ff117>] vp_find_vqs+0x37/0xb0 [virtio_pci]
[ 29.645582] [<ffffffffc057bf63>] init_vq+0x153/0x260 [virtio_blk]
[ 29.658831] [<ffffffffc057c1e8>] virtblk_probe+0xe8/0x87f [virtio_blk]
[...]
Cc: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Longpeng <longpeng2@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
|
|
sun8i_tcon_top_un/bind
There are two problems here:
1. Not all clk_data->hws[] need to be initialized, depending on various
configured quirks. This leads to NULL ptr deref in
clk_hw_unregister_gate() in sun8i_tcon_top_unbind()
2. If there is error when registering the clk_data->hws[],
err_unregister_gates error path will try to unregister
IS_ERR()=true (invalid) pointer.
For problem (1) I have this stack trace:
Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000008
Call trace:
clk_hw_unregister+0x8/0x18
clk_hw_unregister_gate+0x14/0x28
sun8i_tcon_top_unbind+0x2c/0x60
component_unbind.isra.4+0x2c/0x50
component_bind_all+0x1d4/0x230
sun4i_drv_bind+0xc4/0x1a0
try_to_bring_up_master+0x164/0x1c0
__component_add+0xa0/0x168
component_add+0x10/0x18
sun8i_dw_hdmi_probe+0x18/0x20
platform_drv_probe+0x3c/0x70
really_probe+0xcc/0x278
driver_probe_device+0x34/0xa8
Problem (2) was identified by head scratching.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405233048.3823-1-megous@megous.com
|
|
We haven't backmerged for a while and this creates some coherency issues
across DRM drivers.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
If we unplug a udl device, the usb callback with deinit the
mode_config struct, however userspace will still have an open
file descriptor and a framebuffer on that device. When userspace
closes the fd, we'll oops because it'll try and look stuff up
in the object idr which we've destroyed.
This punts destroying the mode objects until release time instead.
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405031715.5959-2-airlied@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a bug in the implementation of xcbc and cmac in caam"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: caam - fix copy of next buffer for xcbc and cmac
|
|
When the mtu of a vrf device is set to 0, it would cause ping
failed. So I think we should limit vrf mtu in a reasonable range
to solve this problem. I set dev->min_mtu to IPV6_MIN_MTU, so it
will works for both ipv4 and ipv6. And if dev->max_mtu still be 0
can be confusing, so I set dev->max_mtu to ETH_MAX_MTU.
Here is the reproduce step:
1.Config vrf interface and set mtu to 0:
3: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel
master vrf1 state UP mode DEFAULT group default qlen 1000
link/ether 52:54:00:9e:dd:c1 brd ff:ff:ff:ff:ff:ff
2.Ping peer:
3: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel
master vrf1 state UP group default qlen 1000
link/ether 52:54:00:9e:dd:c1 brd ff:ff:ff:ff:ff:ff
inet 10.0.0.1/16 scope global enp4s0
valid_lft forever preferred_lft forever
connect: Network is unreachable
3.Set mtu to default value, ping works:
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
64 bytes from 10.0.0.2: icmp_seq=1 ttl=64 time=1.88 ms
Fixes: ad49bc6361ca2 ("net: vrf: remove MTU limits for vrf device")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ppgtt_free_all_spt() iterates the radixtree as it is deleting it,
forgoing all protection against the leaves being freed in the process
(leaving the iter pointing into the void).
A minimal fix seems to be to use the available post_shadow_list to
decompose the tree into a list prior to destroying the radixtree.
Alerted by the sparse warnings:
drivers/gpu/drm/i915/gvt/gtt.c:757:9: warning: incorrect type in assignment (different address spaces)
drivers/gpu/drm/i915/gvt/gtt.c:757:9: expected void **slot
drivers/gpu/drm/i915/gvt/gtt.c:757:9: got void [noderef] <asn:4> **
drivers/gpu/drm/i915/gvt/gtt.c:757:9: warning: incorrect type in assignment (different address spaces)
drivers/gpu/drm/i915/gvt/gtt.c:757:9: expected void **slot
drivers/gpu/drm/i915/gvt/gtt.c:757:9: got void [noderef] <asn:4> **
drivers/gpu/drm/i915/gvt/gtt.c:758:45: warning: incorrect type in argument 1 (different address spaces)
drivers/gpu/drm/i915/gvt/gtt.c:758:45: expected void [noderef] <asn:4> **slot
drivers/gpu/drm/i915/gvt/gtt.c:758:45: got void **slot
drivers/gpu/drm/i915/gvt/gtt.c:757:9: warning: incorrect type in argument 1 (different address spaces)
drivers/gpu/drm/i915/gvt/gtt.c:757:9: expected void [noderef] <asn:4> **slot
drivers/gpu/drm/i915/gvt/gtt.c:757:9: got void **slot
drivers/gpu/drm/i915/gvt/gtt.c:757:9: warning: incorrect type in assignment (different address spaces)
drivers/gpu/drm/i915/gvt/gtt.c:757:9: expected void **slot
drivers/gpu/drm/i915/gvt/gtt.c:757:9: got void [noderef] <asn:4> **
This would also have been loudly warning if run through CI for the
invalid RCU dereferences.
Fixes: b6c126a39345 ("drm/i915/gvt: Manage shadow pages with radix tree")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
Fix the sparse warning for blithely using iomem with normal memcpy:
drivers/gpu/drm/i915/gvt/kvmgt.c:916:21: warning: incorrect type in assignment (different address spaces)
drivers/gpu/drm/i915/gvt/kvmgt.c:916:21: expected void *aperture_va
drivers/gpu/drm/i915/gvt/kvmgt.c:916:21: got void [noderef] <asn:2> *
drivers/gpu/drm/i915/gvt/kvmgt.c:927:26: warning: incorrect type in argument 1 (different address spaces)
drivers/gpu/drm/i915/gvt/kvmgt.c:927:26: expected void [noderef] <asn:2> *vaddr
drivers/gpu/drm/i915/gvt/kvmgt.c:927:26: got void *aperture_va
Fixes: d480b28a41a6 ("drm/i915/gvt: Fix aperture read/write emulation when enable x-no-mmap=on")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes from the last few weeks. Most of them are
smaller tweaks and fixes to DT and hardware descriptions for boards.
Some of the more significant ones are:
- eMMC and RGMII stability tweaks for rk3288
- DDC fixes for Rock PI 4
- Audio fixes for two TI am335x eval boards
- D_CAN clock fix for am335x
- Compilation fixes for clang
- !HOTPLUG_CPU compilation fix for one of the new platforms this
release (milbeaut)
- A revert of a gpio fix for nomadik that instead was fixed in the
gpio subsystem
- Whitespace fix for the DT JSON schema (no tabs allowed)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
ARM: milbeaut: fix build with !CONFIG_HOTPLUG_CPU
ARM: iop: don't use using 64-bit DMA masks
ARM: orion: don't use using 64-bit DMA masks
Revert "ARM: dts: nomadik: Fix polarity of SPI CS"
dt-bindings: cpu: Fix JSON schema
arm/mach-at91/pm : fix possible object reference leak
ARM: dts: at91: Fix typo in ISC_D0 on PC9
ARM: dts: Fix dcan clkctrl clock for am3
reset: meson-audio-arb: Fix missing .owner setting of reset_controller_dev
dt-bindings: reset: meson-g12a: Add missing USB2 PHY resets
ARM: dts: rockchip: Remove #address/#size-cells from rk3288-veyron gpio-keys
ARM: dts: rockchip: Remove #address/#size-cells from rk3288 mipi_dsi
ARM: dts: rockchip: Fix gpu opp node names for rk3288
ARM: dts: am335x-evmsk: Correct the regulators for the audio codec
ARM: dts: am335x-evm: Correct the regulators for the audio codec
ARM: OMAP2+: add missing of_node_put after of_device_is_available
ARM: OMAP1: ams-delta: Fix broken GPIO ID allocation
arm64: dts: stratix10: add the sysmgr-syscon property from the gmac's
arm64: dts: rockchip: fix rk3328 sdmmc0 write errors
arm64: dts: rockchip: fix rk3328 rgmii high tx error rate
...
|
|
Pull block fixes from Jens Axboe:
- Fixups for the pf/pcd queue handling (YueHaibing)
- Revert of the three direct issue changes as they have been proven to
cause an issue with dm-mpath (Bart)
- Plug rq_count reset fix (Dongli)
- io_uring double free in fileset registration error handling (me)
- Make null_blk handle bad numa node passed in (John)
- BFQ ifdef fix (Konstantin)
- Flush queue leak fix (Shenghui)
- Plug trace fix (Yufen)
* tag 'for-linus-20190407' of git://git.kernel.dk/linux-block:
xsysace: Fix error handling in ace_setup
null_blk: prevent crash from bad home_node value
block: Revert v5.0 blk_mq_request_issue_directly() changes
paride/pcd: Fix potential NULL pointer dereference and mem leak
blk-mq: do not reset plug->rq_count before the list is sorted
paride/pf: Fix potential NULL pointer dereference
io_uring: fix double free in case of fileset regitration failure
blk-mq: add trace block plug and unplug for multiple queues
block: use blk_free_flush_queue() to free hctx->fq in blk_mq_init_hctx
block/bfq: fix ifdef for CONFIG_BFQ_GROUP_IOSCHED=y
|
|
arm/fixes
Reset controller fixes for v5.1
This tag adds missing USB PHY reset lines to the Meson G12A reset
controller header and fixes the Meson Audio ARB driver to prevent
module unloading while it is in use.
* tag 'reset-fixes-for-v5.1' of git://git.pengutronix.de/pza/linux:
reset: meson-audio-arb: Fix missing .owner setting of reset_controller_dev
dt-bindings: reset: meson-g12a: Add missing USB2 PHY resets
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"One minor fix and a small cleanup for the xen privcmd driver"
* tag 'for-linus-5.1b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Prevent buffer overflow in privcmd ioctl
xen: use struct_size() helper in kzalloc()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fix from Richard Weinberger:
"A single fix for a possible infinite loop in the cfi_cmdset_0002
driver"
* tag 'mtd/fixes-for-5.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: cfi: fix deadloop in cfi_cmdset_0002.c do_write_buffer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Five small fixes. Four in three drivers: qedi, lpfc and storvsc. The
final one is labelled core, but merely adds a dh rdac entry for Lenovo
systems"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Fix missing wakeups on abort threads
scsi: storvsc: Reduce default ring buffer size to 128 Kbytes
scsi: storvsc: Fix calculation of sub-channel count
scsi: core: add new RDAC LENOVO/DE_Series device
scsi: qedi: remove declaration of nvm_image from stack
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"A simple but wanted driver bugfix"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: don't leak the i2c adapter on error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"A 32-bit boot regression fix introduced in the merge window, a QEMU
detection fix and two fixes by Sven regarding ptrace & kprobes"
* 'parisc-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Detect QEMU earlier in boot process
parisc: also set iaoq_b in instruction_pointer_set()
parisc: regs_return_value() should return gpr28
Revert: parisc: Use F_EXTEND() macro in iosapic code
|
|
Revert parts of commit 97d7e2e3fd8a ("parisc: Use F_EXTEND() macro in
iosapic code"). It breaks booting the 32-bit kernel on some machines.
Reported-by: Sven Schnelle <svens@stackframe.org>
Tested-by: Sven Schnelle <svens@stackframe.org>
Fixes: 97d7e2e3fd8a ("parisc: Use F_EXTEND() macro in iosapic code")
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
run simultaneously without deadlock
Commit 9c225f2655e3 ("vfs: atomic f_pos accesses as per POSIX") added
locking for file.f_pos access and in particular made concurrent read and
write not possible - now both those functions take f_pos lock for the
whole run, and so if e.g. a read is blocked waiting for data, write will
deadlock waiting for that read to complete.
This caused regression for stream-like files where previously read and
write could run simultaneously, but after that patch could not do so
anymore. See e.g. commit 581d21a2d02a ("xenbus: fix deadlock on writes
to /proc/xen/xenbus") which fixes such regression for particular case of
/proc/xen/xenbus.
The patch that added f_pos lock in 2014 did so to guarantee POSIX thread
safety for read/write/lseek and added the locking to file descriptors of
all regular files. In 2014 that thread-safety problem was not new as it
was already discussed earlier in 2006.
However even though 2006'th version of Linus's patch was adding f_pos
locking "only for files that are marked seekable with FMODE_LSEEK (thus
avoiding the stream-like objects like pipes and sockets)", the 2014
version - the one that actually made it into the tree as 9c225f2655e3 -
is doing so irregardless of whether a file is seekable or not.
See
https://lore.kernel.org/lkml/53022DB1.4070805@gmail.com/
https://lwn.net/Articles/180387
https://lwn.net/Articles/180396
for historic context.
The reason that it did so is, probably, that there are many files that
are marked non-seekable, but e.g. their read implementation actually
depends on knowing current position to correctly handle the read. Some
examples:
kernel/power/user.c snapshot_read
fs/debugfs/file.c u32_array_read
fs/fuse/control.c fuse_conn_waiting_read + ...
drivers/hwmon/asus_atk0110.c atk_debugfs_ggrp_read
arch/s390/hypfs/inode.c hypfs_read_iter
...
Despite that, many nonseekable_open users implement read and write with
pure stream semantics - they don't depend on passed ppos at all. And for
those cases where read could wait for something inside, it creates a
situation similar to xenbus - the write could be never made to go until
read is done, and read is waiting for some, potentially external, event,
for potentially unbounded time -> deadlock.
Besides xenbus, there are 14 such places in the kernel that I've found
with semantic patch (see below):
drivers/xen/evtchn.c:667:8-24: ERROR: evtchn_fops: .read() can deadlock .write()
drivers/isdn/capi/capi.c:963:8-24: ERROR: capi_fops: .read() can deadlock .write()
drivers/input/evdev.c:527:1-17: ERROR: evdev_fops: .read() can deadlock .write()
drivers/char/pcmcia/cm4000_cs.c:1685:7-23: ERROR: cm4000_fops: .read() can deadlock .write()
net/rfkill/core.c:1146:8-24: ERROR: rfkill_fops: .read() can deadlock .write()
drivers/s390/char/fs3270.c:488:1-17: ERROR: fs3270_fops: .read() can deadlock .write()
drivers/usb/misc/ldusb.c:310:1-17: ERROR: ld_usb_fops: .read() can deadlock .write()
drivers/hid/uhid.c:635:1-17: ERROR: uhid_fops: .read() can deadlock .write()
net/batman-adv/icmp_socket.c:80:1-17: ERROR: batadv_fops: .read() can deadlock .write()
drivers/media/rc/lirc_dev.c:198:1-17: ERROR: lirc_fops: .read() can deadlock .write()
drivers/leds/uleds.c:77:1-17: ERROR: uleds_fops: .read() can deadlock .write()
drivers/input/misc/uinput.c:400:1-17: ERROR: uinput_fops: .read() can deadlock .write()
drivers/infiniband/core/user_mad.c:985:7-23: ERROR: umad_fops: .read() can deadlock .write()
drivers/gnss/core.c:45:1-17: ERROR: gnss_fops: .read() can deadlock .write()
In addition to the cases above another regression caused by f_pos
locking is that now FUSE filesystems that implement open with
FOPEN_NONSEEKABLE flag, can no longer implement bidirectional
stream-like files - for the same reason as above e.g. read can deadlock
write locking on file.f_pos in the kernel.
FUSE's FOPEN_NONSEEKABLE was added in 2008 in a7c1b990f715 ("fuse:
implement nonseekable open") to support OSSPD. OSSPD implements /dev/dsp
in userspace with FOPEN_NONSEEKABLE flag, with corresponding read and
write routines not depending on current position at all, and with both
read and write being potentially blocking operations:
See
https://github.com/libfuse/osspd
https://lwn.net/Articles/308445
https://github.com/libfuse/osspd/blob/14a9cff0/osspd.c#L1406
https://github.com/libfuse/osspd/blob/14a9cff0/osspd.c#L1438-L1477
https://github.com/libfuse/osspd/blob/14a9cff0/osspd.c#L1479-L1510
Corresponding libfuse example/test also describes FOPEN_NONSEEKABLE as
"somewhat pipe-like files ..." with read handler not using offset.
However that test implements only read without write and cannot exercise
the deadlock scenario:
https://github.com/libfuse/libfuse/blob/fuse-3.4.2-3-ga1bff7d/example/poll.c#L124-L131
https://github.com/libfuse/libfuse/blob/fuse-3.4.2-3-ga1bff7d/example/poll.c#L146-L163
https://github.com/libfuse/libfuse/blob/fuse-3.4.2-3-ga1bff7d/example/poll.c#L209-L216
I've actually hit the read vs write deadlock for real while implementing
my FUSE filesystem where there is /head/watch file, for which open
creates separate bidirectional socket-like stream in between filesystem
and its user with both read and write being later performed
simultaneously. And there it is semantically not easy to split the
stream into two separate read-only and write-only channels:
https://lab.nexedi.com/kirr/wendelin.core/blob/f13aa600/wcfs/wcfs.go#L88-169
Let's fix this regression. The plan is:
1. We can't change nonseekable_open to include &~FMODE_ATOMIC_POS -
doing so would break many in-kernel nonseekable_open users which
actually use ppos in read/write handlers.
2. Add stream_open() to kernel to open stream-like non-seekable file
descriptors. Read and write on such file descriptors would never use
nor change ppos. And with that property on stream-like files read and
write will be running without taking f_pos lock - i.e. read and write
could be running simultaneously.
3. With semantic patch search and convert to stream_open all in-kernel
nonseekable_open users for which read and write actually do not
depend on ppos and where there is no other methods in file_operations
which assume @offset access.
4. Add FOPEN_STREAM to fs/fuse/ and open in-kernel file-descriptors via
steam_open if that bit is present in filesystem open reply.
It was tempting to change fs/fuse/ open handler to use stream_open
instead of nonseekable_open on just FOPEN_NONSEEKABLE flags, but
grepping through Debian codesearch shows users of FOPEN_NONSEEKABLE,
and in particular GVFS which actually uses offset in its read and
write handlers
https://codesearch.debian.net/search?q=-%3Enonseekable+%3D
https://gitlab.gnome.org/GNOME/gvfs/blob/1.40.0-6-gcbc54396/client/gvfsfusedaemon.c#L1080
https://gitlab.gnome.org/GNOME/gvfs/blob/1.40.0-6-gcbc54396/client/gvfsfusedaemon.c#L1247-1346
https://gitlab.gnome.org/GNOME/gvfs/blob/1.40.0-6-gcbc54396/client/gvfsfusedaemon.c#L1399-1481
so if we would do such a change it will break a real user.
5. Add stream_open and FOPEN_STREAM handling to stable kernels starting
from v3.14+ (the kernel where 9c225f2655 first appeared).
This will allow to patch OSSPD and other FUSE filesystems that
provide stream-like files to return FOPEN_STREAM | FOPEN_NONSEEKABLE
in their open handler and this way avoid the deadlock on all kernel
versions. This should work because fs/fuse/ ignores unknown open
flags returned from a filesystem and so passing FOPEN_STREAM to a
kernel that is not aware of this flag cannot hurt. In turn the kernel
that is not aware of FOPEN_STREAM will be < v3.14 where just
FOPEN_NONSEEKABLE is sufficient to implement streams without read vs
write deadlock.
This patch adds stream_open, converts /proc/xen/xenbus to it and adds
semantic patch to automatically locate in-kernel places that are either
required to be converted due to read vs write deadlock, or that are just
safe to be converted because read and write do not use ppos and there
are no other funky methods in file_operations.
Regarding semantic patch I've verified each generated change manually -
that it is correct to convert - and each other nonseekable_open instance
left - that it is either not correct to convert there, or that it is not
converted due to current stream_open.cocci limitations.
The script also does not convert files that should be valid to convert,
but that currently have .llseek = noop_llseek or generic_file_llseek for
unknown reason despite file being opened with nonseekable_open (e.g.
drivers/input/mousedev.c)
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yongzhi Pan <panyongzhi@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Tejun Heo <tj@kernel.org>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Nikolaus Rath <Nikolaus@rath.org>
Cc: Han-Wen Nienhuys <hanwen@google.com>
Signed-off-by: Kirill Smelkov <kirr@nexedi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If xace hardware reports a bad version number, the error handling code
in ace_setup() calls put_disk(), followed by queue cleanup. However, since
the disk data structure has the queue pointer set, put_disk() also
cleans and releases the queue. This results in blk_cleanup_queue()
accessing an already released data structure, which in turn may result
in a crash such as the following.
[ 10.681671] BUG: Kernel NULL pointer dereference at 0x00000040
[ 10.681826] Faulting instruction address: 0xc0431480
[ 10.682072] Oops: Kernel access of bad area, sig: 11 [#1]
[ 10.682251] BE PAGE_SIZE=4K PREEMPT Xilinx Virtex440
[ 10.682387] Modules linked in:
[ 10.682528] CPU: 0 PID: 1 Comm: swapper Tainted: G W 5.0.0-rc6-next-20190218+ #2
[ 10.682733] NIP: c0431480 LR: c043147c CTR: c0422ad8
[ 10.682863] REGS: cf82fbe0 TRAP: 0300 Tainted: G W (5.0.0-rc6-next-20190218+)
[ 10.683065] MSR: 00029000 <CE,EE,ME> CR: 22000222 XER: 00000000
[ 10.683236] DEAR: 00000040 ESR: 00000000
[ 10.683236] GPR00: c043147c cf82fc90 cf82ccc0 00000000 00000000 00000000 00000002 00000000
[ 10.683236] GPR08: 00000000 00000000 c04310bc 00000000 22000222 00000000 c0002c54 00000000
[ 10.683236] GPR16: 00000000 00000001 c09aa39c c09021b0 c09021dc 00000007 c0a68c08 00000000
[ 10.683236] GPR24: 00000001 ced6d400 ced6dcf0 c0815d9c 00000000 00000000 00000000 cedf0800
[ 10.684331] NIP [c0431480] blk_mq_run_hw_queue+0x28/0x114
[ 10.684473] LR [c043147c] blk_mq_run_hw_queue+0x24/0x114
[ 10.684602] Call Trace:
[ 10.684671] [cf82fc90] [c043147c] blk_mq_run_hw_queue+0x24/0x114 (unreliable)
[ 10.684854] [cf82fcc0] [c04315bc] blk_mq_run_hw_queues+0x50/0x7c
[ 10.685002] [cf82fce0] [c0422b24] blk_set_queue_dying+0x30/0x68
[ 10.685154] [cf82fcf0] [c0423ec0] blk_cleanup_queue+0x34/0x14c
[ 10.685306] [cf82fd10] [c054d73c] ace_probe+0x3dc/0x508
[ 10.685445] [cf82fd50] [c052d740] platform_drv_probe+0x4c/0xb8
[ 10.685592] [cf82fd70] [c052abb0] really_probe+0x20c/0x32c
[ 10.685728] [cf82fda0] [c052ae58] driver_probe_device+0x68/0x464
[ 10.685877] [cf82fdc0] [c052b500] device_driver_attach+0xb4/0xe4
[ 10.686024] [cf82fde0] [c052b5dc] __driver_attach+0xac/0xfc
[ 10.686161] [cf82fe00] [c0528428] bus_for_each_dev+0x80/0xc0
[ 10.686314] [cf82fe30] [c0529b3c] bus_add_driver+0x144/0x234
[ 10.686457] [cf82fe50] [c052c46c] driver_register+0x88/0x15c
[ 10.686610] [cf82fe60] [c09de288] ace_init+0x4c/0xac
[ 10.686742] [cf82fe80] [c0002730] do_one_initcall+0xac/0x330
[ 10.686888] [cf82fee0] [c09aafd0] kernel_init_freeable+0x34c/0x478
[ 10.687043] [cf82ff30] [c0002c6c] kernel_init+0x18/0x114
[ 10.687188] [cf82ff40] [c000f2f0] ret_from_kernel_thread+0x14/0x1c
[ 10.687349] Instruction dump:
[ 10.687435] 3863ffd4 4bfffd70 9421ffd0 7c0802a6 93c10028 7c9e2378 93e1002c 38810008
[ 10.687637] 7c7f1b78 90010034 4bfffc25 813f008c <81290040> 75290100 4182002c 80810008
[ 10.688056] ---[ end trace 13c9ff51d41b9d40 ]---
Fix the problem by setting the disk queue pointer to NULL before calling
put_disk(). A more comprehensive fix might be to rearrange the code
to check the hardware version before initializing data structures,
but I don't know if this would have undesirable side effects, and
it would increase the complexity of backporting the fix to older kernels.
Fixes: 74489a91dd43a ("Add support for Xilinx SystemACE CompactFlash interface")
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
At module load, if the selected home_node value is greater than
the available numa nodes, the system will crash in
__alloc_pages_nodemask() due to a bad paging request. Prevent this
user error crash by detecting the bad value, logging an error, and
setting g_home_node back to the default of NUMA_NO_NODE.
Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
- Various alarm fixes for da9063, cros-ec and sh
- sd3078 manufacturer name fix as this was introduced this cycle
* tag 'rtc-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: da9063: set uie_unsupported when relevant
rtc: sd3078: fix manufacturer name
rtc: sh: Fix invalid alarm warning for non-enabled alarm
rtc: cros-ec: Fail suspend/resume if wake IRQ can't be configured
|
|
Make sure to free the i2c adapter on the error exit path.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: e1ab9a468e3b ("i2c: imx: improve the error handling in i2c_imx_dma_request()")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
