| Age | Commit message (Collapse) | Author |
|---|
|
We should use SoC compatible string in stead of wildcard string for
PMIC child devices.
Fixes: 0419a75b1808 (arm64: dts: sprd: Remove wildcard compatible string)
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Since commit 6e2bd956936 ("i2c: omap: Use noirq system sleep pm ops to idle device for suspend")
on gta04 we have handle_twl4030_pih() called in situations where pm_runtime_get()
in i2c-omap.c returns -EACCES.
[ 86.474365] Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
[ 86.485473] printk: Suspending console(s) (use no_console_suspend to debug)
[ 86.555572] Disabling non-boot CPUs ...
[ 86.555664] Successfully put all powerdomains to target state
[ 86.563720] twl: Read failed (mod 1, reg 0x01 count 1)
[ 86.563751] twl4030: I2C error -13 reading PIH ISR
[ 86.563812] twl: Read failed (mod 1, reg 0x01 count 1)
[ 86.563812] twl4030: I2C error -13 reading PIH ISR
[ 86.563873] twl: Read failed (mod 1, reg 0x01 count 1)
[ 86.563903] twl4030: I2C error -13 reading PIH ISR
This happens when we wakeup via something behing twl4030 (powerbutton or rtc
alarm). This goes on for minutes until the system is finally resumed.
Disable the irq on suspend and enable it on resume to avoid
having i2c access problems when the irq registers are checked.
Fixes: 6e2bd956936 ("i2c: omap: Use noirq system sleep pm ops to idle device for suspend")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We don't want to overwrite "ret", it already holds the correct error
code. The "regmap" variable might be a valid pointer as this point.
Fixes: 8f83f26891e1 ("drm/mediatek: Add HDMI support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
We no longer set CFI when pushing vlan tags, therefore we remove
the CFI bit from push vlan.
Fixes: 1a1e586f54bf ("nfp: add basic action capabilities to flower offloads")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace vlan CFI bit with a vlan present bit that indicates the
presence of a vlan tag. Previously the driver incorrectly assumed
that an vlan id of 0 is not matchable, therefore we indicate vlan
presence with a vlan present bit.
Fixes: 5571e8c9f241 ("nfp: extend flower matching capabilities")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver is Intel-only so loading on anything which is not Intel is
pointless. Prevent it from doing so.
While at it, correct the "not supported" print statement to say CPU
"model" which is what that test does.
Fixes: 076b862c7e44 (cpufreq: intel_pstate: Add reasons for failure and debug messages)
Suggested-by: Erwan Velu <e.velu@criteo.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some devices don't use blk_integrity but still want stable pages
because they do their own checksumming. Examples include rbd and iSCSI
when data digests are negotiated. Stacking DM (and thus LVM) on top of
these devices results in sporadic checksum errors.
Set BDI_CAP_STABLE_WRITES if any underlying device has it set.
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
PAGE_SIZE")
The limit was already incorporated to dm-crypt with commit 4e870e948fba
("dm crypt: fix error with too large bios"), so we don't need to apply
it globally to all targets. The quantity BIO_MAX_PAGES * PAGE_SIZE is
wrong anyway because the variable ti->max_io_len it is supposed to be in
the units of 512-byte sectors not in bytes.
Reduction of the limit to 1048576 sectors could even cause data
corruption in rare cases - suppose that we have a dm-striped device with
stripe size 768MiB. The target will call dm_set_target_max_io_len with
the value 1572864. The buggy code would reduce it to 1048576. Now, the
dm-core will errorneously split the bios on 1048576-sector boundary
insetad of 1572864-sector boundary and pass these stripe-crossing bios
to the striped target.
Cc: stable@vger.kernel.org # v4.16+
Fixes: 8f50e358153d ("dm: limit the max bio size as BIO_MAX_PAGES * PAGE_SIZE")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
A non const pointer to const cannot be marked initconst.
Mark the array actually const.
Fixes: 6bbc923dfcf5 dm: add support to directly boot to a mapped device
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Fix sparse warnings:
drivers/md/dm-integrity.c:3619:12: warning:
symbol 'dm_integrity_init' was not declared. Should it be static?
drivers/md/dm-integrity.c:3638:6: warning:
symbol 'dm_integrity_exit' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
If the string opt_string is small, the function memcmp can access bytes
that are beyond the terminating nul character. In theory, it could cause
segfault, if opt_string were located just below some unmapped memory.
Change from memcmp to strncmp so that we don't read bytes beyond the end
of the string.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
In commit f3fef2b6e1cc ("i40e: Remove umem from VSI") a regression was
introduced; When the VSI was reset, the setup code would try to enable
AF_XDP ZC unconditionally (as long as there was a umem placed in the
netdev._rx struct). Here, we add a bitmap to the VSI that tracks if a
certain queue pair has been "zero-copy enabled" via the ndo_bpf. The
bitmap is used in i40e_xsk_umem, and enables zero-copy if and only if
XDP is enabled, the corresponding qid in the bitmap is set and the
umem is non-NULL.
Fixes: f3fef2b6e1cc ("i40e: Remove umem from VSI")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The i40e_xsk_umem function was explicitly inlined in i40e.h. There is
no reason for that, so move it to i40e_main.c instead.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If drm_modeset_lock() reports a deadlock it sets the ctx->contexted
field and insists that the caller calls drm_modeset_backoff() or else it
generates a WARN on cleanup.
<4> [1601.870376] WARNING: CPU: 3 PID: 8445 at drivers/gpu/drm/drm_modeset_lock.c:228 drm_modeset_drop_locks+0x35/0x40
<4> [1601.870395] Modules linked in: vgem snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic x86_pkg_temp_thermal i915 coretemp crct10dif_pclmul
<6> [1601.870403] Console: switching
<4> [1601.870403] snd_hda_intel
<4> [1601.870406] to colour frame buffer device 320x90
<4> [1601.870406] crc32_pclmul snd_hda_codec snd_hwdep ghash_clmulni_intel e1000e snd_hda_core cdc_ether ptp usbnet mii pps_core snd_pcm i2c_i801 mei_me mei prime_numbers
<4> [1601.870422] CPU: 3 PID: 8445 Comm: cat Tainted: G U 5.0.0-rc7-CI-CI_DRM_5650+ #1
<4> [1601.870424] Hardware name: Intel Corporation Ice Lake Client Platform/IceLake U DDR4 SODIMM PD RVP TLC, BIOS ICLSFWR1.R00.2402.AD3.1810170014 10/17/2018
<4> [1601.870427] RIP: 0010:drm_modeset_drop_locks+0x35/0x40
<4> [1601.870430] Code: 29 48 8b 43 60 48 8d 6b 60 48 39 c5 74 19 48 8b 43 60 48 8d b8 70 ff ff ff e8 87 ff ff ff 48 8b 43 60 48 39 c5 75 e7 5b 5d c3 <0f> 0b eb d3 0f 1f 80 00 00 00 00 41 56 41 55 41 54 55 53 48 8b 6f
<4> [1601.870432] RSP: 0018:ffffc90000d67ce8 EFLAGS: 00010282
<4> [1601.870435] RAX: 00000000ffffffdd RBX: ffffc90000d67d00 RCX: 5dbbe23d00000000
<4> [1601.870437] RDX: 0000000000000000 RSI: 0000000093e6194a RDI: ffffc90000d67d00
<4> [1601.870439] RBP: ffff88849e62e678 R08: 0000000003b7329a R09: 0000000000000001
<4> [1601.870441] R10: 0000000000000000 R11: 0000000000000000 R12: ffff888492100410
<4> [1601.870442] R13: ffff88849ea50958 R14: ffff8884a67eb028 R15: ffff8884a67eb028
<4> [1601.870445] FS: 00007fa7a27745c0(0000) GS:ffff8884aff80000(0000) knlGS:0000000000000000
<4> [1601.870447] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4> [1601.870449] CR2: 000055af07e66000 CR3: 00000004a8cc2006 CR4: 0000000000760ee0
<4> [1601.870451] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
<4> [1601.870453] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
<4> [1601.870454] PKRU: 55555554
<4> [1601.870456] Call Trace:
<4> [1601.870505] i915_dsc_fec_support_show+0x91/0x190 [i915]
<4> [1601.870522] seq_read+0xdb/0x3c0
<4> [1601.870531] full_proxy_read+0x51/0x80
<4> [1601.870538] __vfs_read+0x31/0x190
<4> [1601.870546] ? __se_sys_newfstat+0x3c/0x60
<4> [1601.870552] vfs_read+0x9e/0x150
<4> [1601.870557] ksys_read+0x50/0xc0
<4> [1601.870564] do_syscall_64+0x55/0x190
<4> [1601.870569] entry_SYSCALL_64_after_hwframe+0x49/0xbe
<4> [1601.870572] RIP: 0033:0x7fa7a226d081
<4> [1601.870574] Code: fe ff ff 48 8d 3d 67 9c 0a 00 48 83 ec 08 e8 a6 4c 02 00 66 0f 1f 44 00 00 48 8d 05 81 08 2e 00 8b 00 85 c0 75 13 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 57 f3 c3 0f 1f 44 00 00 41 54 55 49 89 d4 53
<4> [1601.870576] RSP: 002b:00007ffcc05140c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
<4> [1601.870579] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007fa7a226d081
<4> [1601.870581] RDX: 0000000000020000 RSI: 000055af07e63000 RDI: 0000000000000007
<4> [1601.870583] RBP: 0000000000020000 R08: 000000000000007b R09: 0000000000000000
<4> [1601.870585] R10: 000055af07e60010 R11: 0000000000000246 R12: 000055af07e63000
<4> [1601.870587] R13: 0000000000000007 R14: 000055af07e634bf R15: 0000000000020000
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109745
Fixes: e845f099f1c6 ("drm/i915/dsc: Add Per connector debugfs node for DSC support/enable")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190329165152.29259-1-chris@chris-wilson.co.uk
(cherry picked from commit ee6df5694a9a2e30566ae05e9c145a0f6d5e087f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
We have a new Dell laptop which has the synaptics I2C touchpad
(06cb:7e7e) on it. After booting up the Linux, the touchpad doesn't
work, there is no interrupt when touching the touchpad, after
disable the runtime PM, everything works well.
I also tried the quirk of I2C_HID_QUIRK_DELAY_AFTER_SLEEP, it is
better after applied this quirk, there are interrupts but data it
reports is invalid.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This is log is harmful as it can trigger multiple times per packet. Delete
it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets without the last descriptor set should be dropped early. If we
receive a frame larger than the DMA buffer, the HW will continue using the
next descriptor. Driver mistakes these as individual frames, and sometimes
a truncated frame (without the LD set) may look like a valid packet.
This fixes a strange issue where the system replies to 4098-byte ping
although the MTU/DMA buffer size is set to 4096, and yet at the same
time it's logging an oversized packet.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we have error bits set, the discard_frame status will get overwritten
by checksum bit checks, which might set the status back to good one.
Fix by checking the COE status only if the frame is good.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if we drop a packet, we exit from NAPI loop before the budget
is consumed. In some situations this will make the RX processing stall
e.g. when flood pinging the system with oversized packets, as the
errorneous packets are not dropped efficiently.
If we drop a packet, we should just continue to the next one as long as
the budget allows.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ratelimit RX error logs.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We always program the maximum DMA buffer size into the receive descriptor,
although the allocated size may be less. E.g. with the default MTU size
we allocate only 1536 bytes. If somebody sends us a bigger frame, then
memory may get corrupted.
Fix by using exact buffer sizes.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
- Revert "dmaengine: stm32-mdma: Add a check on read_u32_array" as that
caused regression
- Fix MAINTAINER file uniphier-mdmac.c file path
* tag 'dmaengine-fix-5.1-rc3' of git://git.infradead.org/users/vkoul/slave-dma:
MAINTAINERS: Fix uniphier-mdmac.c file path
dmaengine: stm32-mdma: Revert "dmaengine: stm32-mdma: Add a check on read_u32_array"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
- fix refcnt leak on interface rename
- use memcpy in device_name_store() to avoid including garbage from a
previous, longer value in the device_name
- fix a potential NULL pointer dereference in case of_match_device()
cannot find a match
* tag 'led-fixes-for-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: trigger: netdev: use memcpy in device_name_store
leds: pca9532: fix a potential NULL pointer dereference
leds: trigger: netdev: fix refcnt leak on interface rename
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"As you can see [in the git history] I was away on leave and Bartosz
kindly stepped in and collected a slew of fixes, I pulled them into my
tree in two sets and merged some two more fixes (fixing my own caused
bugs) on top.
Summary:
- Revert the extended use of gpio_set_config() and think about how we
can do this properly.
- Fix up the SPI CS GPIO handling so it now works properly on the SPI
bus children, as intended.
- Error paths and driver fixes"
* tag 'gpio-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mockup: use simple_read_from_buffer() in debugfs read callback
gpio: of: Fix of_gpiochip_add() error path
gpio: of: Check for "spi-cs-high" in child instead of parent node
gpio: of: Check propname before applying "cs-gpios" quirks
gpio: mockup: fix debugfs read
Revert "gpio: use new gpio_set_config() helper in more places"
gpio: aspeed: fix a potential NULL pointer dereference
gpio: amd-fch: Fix bogus SPDX identifier
gpio: adnp: Fix testing wrong value in adnp_gpio_direction_input
gpio: exar: add a check for the return value of ida_simple_get fails
|
|
If userspace doesn't end the input with a newline (which can easily
happen if the write happens from a C program that does write(fd,
iface, strlen(iface))), we may end up including garbage from a
previous, longer value in the device_name. For example
# cat device_name
# printf 'eth12' > device_name
# cat device_name
eth12
# printf 'eth3' > device_name
# cat device_name
eth32
I highly doubt anybody is relying on this behaviour, so switch to
simply copying the bytes (we've already checked that size is <
IFNAMSIZ) and unconditionally zero-terminate it; of course, we also
still have to strip a trailing newline.
This is also preparation for future patches.
Fixes: 06f502f57d0d ("leds: trigger: Introduce a NETDEV trigger")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
It was reported that re-introducing ASPM, in combination with RX
interrupt coalescing, results in significantly increased packet
latency, see [0]. Disabling ASPM or RX interrupt coalescing fixes
the issue. Therefore change the driver's default to disable RX
interrupt coalescing. Users still have the option to enable RX
coalescing via ethtool.
[0] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=925496
Fixes: a99790bf5c7f ("r8169: Reinstate ASPM Support")
Reported-by: Mike Crowe <mac@mcrowe.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of_match_device cannot find a match, return -EINVAL to avoid
NULL pointer dereference.
Fixes: fa4191a609f2 ("leds: pca9532: Add device tree support")
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some small staging driver fixes for 5.1-rc3, and one driver
removal.
The biggest thing here is the removal of the mt7621-eth driver as a
"real" network driver was merged in 5.1-rc1 for this hardware, so this
old driver can now be removed.
Other than that, there are just a number of small fixes, all resolving
reported issues and some potential corner cases for error handling
paths.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt6655: Remove vif check from vnt_interrupt
staging: erofs: keep corrupted fs from crashing kernel in erofs_readdir()
staging: octeon-ethernet: fix incorrect PHY mode
staging: vc04_services: Fix an error code in vchiq_probe()
staging: erofs: fix error handling when failed to read compresssed data
staging: vt6655: Fix interrupt race condition on device start up.
staging: rtlwifi: Fix potential NULL pointer dereference of kzalloc
staging: rtl8712: uninitialized memory in read_bbreg_hdl()
staging: rtlwifi: rtl8822b: fix to avoid potential NULL pointer dereference
staging: rtl8188eu: Fix potential NULL pointer dereference of kcalloc
staging, mt7621-pci: fix build without pci support
staging: speakup_soft: Fix alternate speech with other synths
staging: axis-fifo: add CONFIG_OF dependency
staging: olpc_dcon_xo_1: add missing 'const' qualifier
staging: comedi: ni_mio_common: Fix divide-by-zero for DIO cmdtest
staging: erofs: fix to handle error path of erofs_vmap()
staging: mt7621-dts: update ethernet settings.
staging: remove mt7621-eth
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 5.1-rc3.
Nothing major here, just a number of potential problems fixes for
error handling paths, as well as some other minor bugfixes for
reported issues with 5.1-rc1.
All of these have been in linux-next with no reported issues"
* tag 'tty-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: fix NULL pointer issue when tty_port ops is not set
Disable kgdboc failed by echo space to /sys/module/kgdboc/parameters/kgdboc
dt-bindings: serial: Add compatible for Mediatek MT8183
tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped
tty/serial: atmel: Add is_half_duplex helper
serial: sh-sci: Fix setting SCSCR_TIE while transferring data
serial: ar933x_uart: Fix build failure with disabled console
tty: serial: qcom_geni_serial: Initialize baud in qcom_geni_console_setup
sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()
tty: mxs-auart: fix a potential NULL pointer dereference
tty: atmel_serial: fix a potential NULL pointer dereference
serial: max310x: Fix to avoid potential NULL pointer dereference
serial: mvebu-uart: Fix to avoid a potential NULL pointer dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.1-rc3.
Nothing major at all here, just a small collection of fixes for
reported issues, and potential problems with error handling paths.
Also a few new device ids, as normal.
All of these have been in linux-next with no reported issues"
* tag 'usb-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: serial: option: add Olicard 600
USB: serial: cp210x: add new device id
usb: u132-hcd: fix resource leak
usb: cdc-acm: fix race during wakeup blocking TX traffic
usb: mtu3: fix EXTCON dependency
usb: usb251xb: fix to avoid potential NULL pointer dereference
usb: core: Try generic PHY_MODE_USB_HOST if usb_phy_roothub_set_mode fails
phy: sun4i-usb: Support set_mode to USB_HOST for non-OTG PHYs
xhci: Don't let USB3 ports stuck in polling state prevent suspend
usb: xhci: dbc: Don't free all memory with spinlock held
xhci: Fix port resume done detection for SS ports with LPM enabled
USB: serial: mos7720: fix mos_parport refcount imbalance on error path
USB: gadget: f_hid: fix deadlock in f_hidg_write()
usb: gadget: net2272: Fix net2272_dequeue()
usb: gadget: net2280: Fix net2280_dequeue()
usb: gadget: net2280: Fix overrun of OUT messages
usb: dwc3: pci: add support for Comet Lake PCH ID
usb: usb251xb: Remove unnecessary comparison of unsigned integer with >= 0
usb: common: Consider only available nodes for dr_mode
usb: typec: tcpm: Try PD-2.0 if sink does not respond to 3.0 source-caps
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"This corrects a previous attempt to make Linux use its own set of ACPI
debug flags different from the upstream ACPICA's default (Erik
Schmauss)"
* tag 'acpi-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: use different default debug value than ACPICA
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix CPU base frequency reporting in the intel_pstate driver and
a use-after-free in the scpi-cpufreq driver.
Specifics:
- Fix the ACPI CPPC library to actually follow the specification when
decoding the guaranteed performance register information and make
the intel_pstate driver to fall back to the nominal frequency when
reporting the base frequency if the guaranteed performance register
information is not there (Srinivas Pandruvada).
- Fix use-after-free in the exit callback of the scpi-cpufreq left
after an update during the 5.0 development cycle (Vincent Stehlé)"
* tag 'pm-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: scpi: Fix use after free
cpufreq: intel_pstate: Also use CPPC nominal_perf for base_frequency
ACPI / CPPC: Fix guaranteed performance handling
|
|
Merge misc fixes from Andrew Morton:
"22 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
fs/proc/proc_sysctl.c: fix NULL pointer dereference in put_links
fs: fs_parser: fix printk format warning
checkpatch: add %pt as a valid vsprintf extension
mm/migrate.c: add missing flush_dcache_page for non-mapped page migrate
drivers/block/zram/zram_drv.c: fix idle/writeback string compare
mm/page_isolation.c: fix a wrong flag in set_migratetype_isolate()
mm/memory_hotplug.c: fix notification in offline error path
ptrace: take into account saved_sigmask in PTRACE{GET,SET}SIGMASK
fs/proc/kcore.c: make kcore_modules static
include/linux/list.h: fix list_is_first() kernel-doc
mm/debug.c: fix __dump_page when mapping->host is not set
mm: mempolicy: make mbind() return -EIO when MPOL_MF_STRICT is specified
include/linux/hugetlb.h: convert to use vm_fault_t
iommu/io-pgtable-arm-v7s: request DMA32 memory, and improve debugging
mm: add support for kmem caches in DMA32 zone
ocfs2: fix inode bh swapping mixup in ocfs2_reflink_inodes_lock
mm/hotplug: fix offline undo_isolate_page_range()
fs/open.c: allow opening only regular files during execve()
mailmap: add Changbin Du
mm/debug.c: add a cast to u64 for atomic64_read()
...
|
|
https://github.com/BayLibre/clk-meson into clk-fixes
Pull more fixes for meson clocks from Neil Armstrong:
- clk-pll: fix rate rounding fixing meson8b boot failure
- vid-pll-div: fix recal_rate warning and return when invalid setting
* tag 'meson-clk-fixes-for-5.1-v2' of https://github.com/BayLibre/clk-meson:
clk: meson: vid-pll-div: remove warning and return 0 on invalid config
clk: meson: pll: fix rounding and setting a rate that matches precisely
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- Fix a bug in the AMD IOMMU driver not handling exclusion ranges
correctly. In fact the driver did not reserve these ranges for IOVA
allocations, so that dma-handles could be allocated in an exclusion
range, leading to data corruption. Exclusion ranges have not been
used by any firmware up to now, so this issue remained undiscovered
for quite some time.
- Fix wrong warning messages that the IOMMU core code prints when it
tries to allocate the default domain for an iommu group and the
driver does not support any of the default domain types (like Intel
VT-d).
* tag 'iommu-fixes-v5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Reserve exclusion range in iova-domain
iommu: Don't print warning when IOMMU driver only supports unmanaged domains
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-03-29
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.11
('net/mlx5: Decrease default mr cache size')
For -stable v4.12
('net/mlx5e: Add a lock on tir list')
For -stable v4.13
('net/mlx5e: Fix error handling when refreshing TIRs')
For -stable v4.18
('net/mlx5e: Update xon formula')
For -stable v4.19
('net: mlx5: Add a missing check on idr_find, free buf')
('net/mlx5e: Update xoff formula')
net-next merge Note:
When merged with net-next the following simple conflict will appear,
drivers/net/ethernet/mellanox/mlx5/core/en/port_buffer.c
++<<<<<<< HEAD (net)
+ * max_mtu: netdev's max_mtu
++=======
+ * @mtu: device's MTU
++>>>>>>> net-next
To resolve: just replace the line in net-next
* @mtu: device's MTU
to
* @max_mtu: netdev's max_mtu
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some binder, habanalabs, and vboxguest driver fixes for
5.1-rc3.
The Binder fixes resolve some reported issues found by testing, first
by the selinux developers, and then earlier today by syzbot.
The habanalabs fixes are all minor, resolving a number of tiny things.
The vboxguest patches are a bit larger. They resolve the fact that
virtual box decided to change their api in their latest release in a
way that broke the existing kernel code, despite saying that they were
never going to do that. So this is a bit of a "new feature", but is
good to get merged so that 5.1 will work with the latest release. The
changes are not large and of course virtual box "swears" they will not
break this again, but no one is holding their breath here.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
virt: vbox: Implement passing requestor info to the host for VirtualBox 6.0.x
binder: fix race between munmap() and direct reclaim
binder: fix BUG_ON found by selinux-testsuite
habanalabs: cast to expected type
habanalabs: prevent host crash during suspend/resume
habanalabs: perform accounting for active CS
habanalabs: fix mapping with page size bigger than 4KB
habanalabs: complete user context cleanup before hard reset
habanalabs: fix bug when mapping very large memory area
habanalabs: fix MMU number of pages calculation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Thirteen fixes, seven of which are for IBM fibre channel and three
additional for fairly serious bugs in drivers (qla2xxx, mpt3sas,
aacraid).
Of the three core fixes, the most significant is probably the missed
run queue causing an indefinite hang. The others are fixing a
potential use after free on device close and silencing an incorrect
warning"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ibmvfc: Clean up transport events
scsi: ibmvfc: Byte swap status and error codes when logging
scsi: ibmvfc: Add failed PRLI to cmd_status lookup array
scsi: ibmvfc: Remove "failed" from logged errors
scsi: zfcp: reduce flood of fcrscn1 trace records on multi-element RSCN
scsi: zfcp: fix scsi_eh host reset with port_forced ERP for non-NPIV FCP devices
scsi: zfcp: fix rport unblock if deleted SCSI devices on Scsi_Host
scsi: sd: Quiesce warning if device does not report optimal I/O size
scsi: sd: Fix a race between closing an sd device and sd I/O
scsi: core: Run queue when state is set to running after being blocked
scsi: qla4xxx: fix a potential NULL pointer dereference
scsi: aacraid: Insure we don't access PCIe space during AER/EEH
scsi: mpt3sas: Fix kernel panic during expander reset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"A new ID for the i801 driver and some Documentation fixes to make it
easier for people to find the bindings (which is also a basis for
further improvements in that area)"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: wmt: make bindings file name match the driver
i2c: sun6i-p2wi: make bindings file name match the driver
i2c: stu300: make bindings file name match the driver
i2c: mt65xx: make bindings file name match the driver
i2c: iop3xx: make bindings file name match the driver
i2c: i801: Add support for Intel Comet Lake
|
|
Pull block fixes from Jens Axboe:
"Small set of fixes that should go into this series. This contains:
- compat signal mask fix for io_uring (Arnd)
- EAGAIN corner case for direct vs buffered writes for io_uring
(Roman)
- NVMe pull request from Christoph with various little fixes
- sbitmap ws_active fix, which caused a perf regression for shared
tags (me)
- sbitmap bit ordering fix (Ming)
- libata on-stack DMA fix (Raymond)"
* tag 'for-linus-20190329' of git://git.kernel.dk/linux-block:
nvmet: fix error flow during ns enable
nvmet: fix building bvec from sg list
nvme-multipath: relax ANA state check
nvme-tcp: fix an endianess miss-annotation
libata: fix using DMA buffers on stack
io_uring: offload write to async worker in case of -EAGAIN
sbitmap: order READ/WRITE freed instance and setting clear bit
blk-mq: fix sbitmap ws_active for shared tags
io_uring: fix big-endian compat signal mask handling
blk-mq: update comment for blk_mq_hctx_has_pending()
blk-mq: use blk_mq_put_driver_tag() to put tag
|
|
This reverts commit 4d31c4fa3f9ef7b7e2e79fd57d21290f64c938f5.
Accidently applied this to the wrong tree.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change t4fw_version.h to update latest firmware version
number to 1.23.3.0.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After queue stopped, the wakeup mechanism may wake it up again
when ring buffer usage is lower than a threshold. This may cause
send path panic on NULL pointer when we stopped all tx queues in
netvsc_detach and start removing the netvsc device.
This patch fix it by adding a tx_disable flag to prevent unwanted
queue wakeup.
Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic")
Reported-by: Mohammed Gamal <mgamal@redhat.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bond expects ethernet hwaddr for its slave, but it can be longer than 6
bytes - infiniband interface for example.
# cat /sys/devices/<skipped>/net/ib0/address
80:00:02:08:fe:80:00:00:00:00:00:00:7c:fe:90:03:00:be:5d:e1
# cat /sys/devices/<skipped>/net/ib0/bonding_slave/perm_hwaddr
80:00:02:08:fe:80
So print full hwaddr in sysfs "bonding_slave/perm_hwaddr" as well.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver allocates an encap context based on the tunnel properties,
and reuse that context for all flows using the same tunnel properties.
Commit df2ef3bff193 ("net/mlx5e: Add GRE protocol offloading")
introduced another tunnel protocol other than the single VXLAN
previously supported. A flow that uses a tunnel with the same tunnel
properties but with a different tunnel type (GRE vs VXLAN for example)
would mistakenly reuse the previous alocated context, causing the
traffic to be sent with the wrong encapsulation. Fix that by
considering the tunnel type for encap contexts.
Fixes: df2ef3bff193 ("net/mlx5e: Add GRE protocol offloading")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Set xon = xoff - netdev's max_mtu.
netdev's max_mtu will give enough time for the pause frame to
arrive at the sender.
Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Set minimum speed in xoff threshold formula to 40Gbps
Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Make sure the struct mlx5_flow_destination is zero before
filling in the field.
Fixes: 8da202b24913 ("net/mlx5: E-Switch, Add support for VEPA in legacy mode.")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Traditionally, the PF (Physical Function) which resides on vport 0 was
the E-switch manager. Since the ECPF (Embedded CPU Physical Function),
which resides on vport 0xfffe, was introduced as the E-Switch manager,
the assumption that the E-switch manager is on vport 0 is incorrect.
Since the eswitch code already uses the actual vport value, all we
need is to always set other_vport=1.
Signed-off-by: Omri Kahalon <omrik@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The esw offloads structures share a union with the legacy mode structs.
Reset the offloads struct to zero in init to protect from null
assumptions made by the legacy mode code.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
