| Age | Commit message (Collapse) | Author |
|---|
|
- Configure endpoint BAR to be 64-bit if the PCI_BASE_ADDRESS_MEM_TYPE_64
flag is set instead of depending on the new BAR value itself (Niklas
Cassel)
* pci/controller/cadence:
PCI: cadence: Set a 64-bit BAR if requested
|
|
- Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports because we can't get
them back out of D3cold (Mario Limonciello)
* pci/pm:
PCI/PM: Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports
|
|
- Check for kcalloc() failure and handle it gracefully (Duoming Zhou)
* pci/of:
PCI: of_property: Return error for int_map allocation failure
|
|
- Update coding style to "mainline is normal path, errors are the
exceptions" (Andy Shevchenko)
* pci/msi:
PCI/MSI: Make error path handling follow the standard pattern
|
|
- Update hotplug TODO notes (Nam Cao)
* pci/hotplug:
PCI: hotplug: Remove obsolete sgi_hotplug TODO notes
PCI: hotplug: Document unchecked return value of pci_hp_add_bridge()
|
|
- Clear bridge Secondary Status errors after enumeration since enumeration
causes many errors (Vidya Sagar)
- Wait for Link Training==0 before starting Link retrain to avoid a race;
this was done previously but broken by a faulty merge (Ilpo Järvinen)
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific about what
"LEGACY" means (Damien Le Moal)
- Update return types of pci_find_capability() stubs to match the extern
declarations for the actual implementations (Bjorn Helgaas)
- Drop unnecessary pci_enable_device_io() from pata_cs5520 (Heiner
Kallweit)
- Drop unused pci_enable_device_io() (Heiner Kallweit)
- On 2016 and newer BIOSes, skip early E820 check for ECAM regions
described in ACPI MCFG; there's no spec requirement for E820
reservations, and some machines don't provide them (Bjorn Helgaas)
- If devices were disconnected while suspended, don't wait for them when
resuming (Ilpo Järvinen)
* pci/enumeration:
PCI: Do not wait for disconnected devices when resuming
x86/pci: Skip early E820 check for ECAM region
PCI: Remove unused pci_enable_device_io()
ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io()
PCI: Update pci_find_capability() stub return types
PCI: Remove PCI_IRQ_LEGACY
scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY
scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
wifi: rtw88: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
wifi: ath10k: Refer to INTX instead of LEGACY
net: wangxun: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
r8169: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
net: alx: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
net: atlantic: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
net: amd-xgbe: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
VMCI: Use PCI_IRQ_ALL_TYPES to remove PCI_IRQ_LEGACY use
RDMA/vmw_pvrdma: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
IB/qib: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
drm/amdgpu: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
mfd: intel-lpss: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
ntb: idt: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
platform/x86: intel_ips: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
tty: 8250_pci: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
usb: hcd-pci: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
ASoC: Intel: avs: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
Documentation: PCI: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
PCI/portdrv: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
PCI/MSI: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
PCI: Clarify intent of LT wait
PCI: Wait for Link Training==0 before starting Link retrain
PCI: Clear Secondary Status errors after enumeration
|
|
- Specify Revision 6 of the "Enable DPC" _DSM function to match the
implementation (Kuppuswamy Sathyanarayanan)
- Check for failure of the "Locate Port" _DSM function (Kuppuswamy
Sathyanarayanan)
* pci/edr:
PCI/EDR: Align EDR_PORT_LOCATE_DSM with PCI Firmware r3.3
PCI/EDR: Align EDR_PORT_DPC_ENABLE_DSM with PCI Firmware r3.3
|
|
- Add support for DOE Discovery version 2 (Alexey Kardashevskiy)
* pci/doe:
PCI/DOE: Support discovery version 2
|
|
- Lock the upstream bridge while using it to perform a Secondary Bus Reset
(Dave Jiang)
- Return failure when attempting Secondary Bus Reset below a CXL Port that
has SBR masked (Dave Jiang)
- Add a "cxl_bus" reset method that temporarily unmasks SBR (Dave Jiang)
- Add a warning if we reset a CXL type 3 memory device that was in use
while being reset (Dave Jiang)
* pci/cxl:
cxl: Add post-reset warning if reset results in loss of previously committed HDM decoders
PCI/CXL: Add 'cxl_bus' reset method for devices below CXL Ports
PCI/CXL: Fail bus reset if upstream CXL Port has SBR masked
PCI: Lock upstream bridge for pci_reset_function()
PCI/CXL: Move CXL Vendor ID to pci_ids.h
|
|
- Consolidate #defines for link states (L0s, L1, L1.1, etc) to simplify
ASPM implementation (Ilpo Järvinen)
- Simplify ASPM disable/enable mask calculation (Ilpo Järvinen)
* pci/aspm:
PCI/ASPM: Clean up ASPM disable/enable mask calculation
PCI/ASPM: Consolidate link state defines
|
|
On runtime resume, pci_dev_wait() is called:
pci_pm_runtime_resume()
pci_pm_bridge_power_up_actions()
pci_bridge_wait_for_secondary_bus()
pci_dev_wait()
While a device is runtime suspended along with its PCI hierarchy, the
device could get disconnected. In such case, the link will not come up no
matter how long pci_dev_wait() waits for it.
Besides the above mentioned case, there could be other ways to get the
device disconnected while pci_dev_wait() is waiting for the link to come
up.
Make pci_dev_wait() exit if the device is already disconnected to avoid
unnecessary delay.
The use cases of pci_dev_wait() boil down to two:
1. Waiting for the device after reset
2. pci_bridge_wait_for_secondary_bus()
The callers in both cases seem to benefit from propagating the
disconnection as error even if device disconnection would be more
analoguous to the case where there is no device in the first place which
return 0 from pci_dev_wait(). In the case 2, it results in unnecessary
marking of the devices disconnected again but that is just harmless extra
work.
Also make sure compiler does not become too clever with dev->error_state
and use READ_ONCE() to force a fetch for the up-to-date value.
Link: https://lore.kernel.org/r/20240208132322.4811-1-ilpo.jarvinen@linux.intel.com
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
After the last user was removed, remove this PCI core function. It's very
unlikely that we'll see a new device requiring io space access, even though
memory space access is supported.
Link: https://lore.kernel.org/r/213ebf62-53a3-42b7-8518-ecd5cd6d6b08@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
|
|
A few lines earlier pcim_enable_device() is called, which includes the
functionality of pci_enable_device_io(). Therefore we can safely remove the
call to pci_enable_device_io().
Link: https://lore.kernel.org/r/5068d0ce-2140-4d3f-b305-e8f0d61eed1f@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
|
|
In pvscsi_probe(), initialize irq_flag using PCI_IRQ_ALL_TYPES to remove
the use of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-28-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-27-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-26-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-25-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-24-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-23-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-22-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-21-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The custom EC address space handler in the WMI driver was only needed
because the EC driver did not install its address space handler for
EC operation regions beyond the EC device scope in the ACPI namespace.
That has just changed, so the custom EC address handler is not needed
any more and it can be removed.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
It is reported that _DSM evaluation fails in ucsi_acpi_dsm() on Lenovo
IdeaPad Pro 5 due to a missing address space handler for the EC address
space:
ACPI Error: No handler for Region [ECSI] (000000007b8176ee) [EmbeddedControl] (20230628/evregion-130)
This happens because if there is no ECDT, the EC driver only registers
the EC address space handler for operation regions defined in the EC
device scope of the ACPI namespace while the operation region being
accessed by the _DSM in question is located beyond that scope.
To address this, modify the ACPI EC driver to install the EC address
space handler at the root of the ACPI namespace for the first EC that
can be found regardless of whether or not an ECDT is present.
Note that this change is consistent with some examples in the ACPI
specification in which EC operation regions located outside the EC
device scope are used (for example, see Section 9.17.15 in ACPI 6.5),
so the current behavior of the EC driver is arguably questionable.
Reported-by: webcaptcha <webcapcha@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218789
Link: https://uefi.org/specs/ACPI/6.5/09_ACPI_Defined_Devices_and_Device_Specific_Objects.html#example-asl-code
Link: https://lore.kernel.org/linux-acpi/Zi+0whTvDbAdveHq@kuha.fi.intel.com
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- New drivers/platform/arm64 directory for arm64 embedded-controller
drivers
- New drivers:
- Acer Aspire 1 embedded controllers (for arm64 models)
- ACPI quickstart PNP0C32 buttons
- Dell All-In-One backlight support (dell-uart-backlight)
- Lenovo WMI camera buttons
- Lenovo Yoga Tablet 2 Pro 1380F/L fast charging
- MeeGoPad ANX7428 Type-C Cross Switch (power sequencing only)
- MSI WMI sensors (fan speed sensors only for now)
- Asus WMI:
- 2024 ROG Mini-LED support
- MCU powersave support
- Vivobook GPU MUX support
- Misc. other improvements
- Ideapad laptop:
- Export FnLock LED as LED class device
- Switch platform profiles using thermal management key
- Intel drivers:
- IFS: various improvements
- PMC: Lunar Lake support
- SDSI: various improvements
- TPMI/ISST: various improvements
- tools: intel-speed-select: various improvements
- MS Surface drivers:
- Fan profile switching support
- Surface Pro thermal sensors support
- ThinkPad ACPI:
- Reworked hotkey support to use sparse keymaps
- Add support for new trackpoint-doubletap, Fn+N and Fn+G hotkeys
- WMI core:
- New WMI driver development guide
- x86 Android tablets:
- Lenovo Yoga Tablet 2 Pro 1380F/L support
- Xiaomi MiPad 2 status LED and bezel touch buttons backlight
support
- Miscellaneous cleanups / fixes / improvements
* tag 'platform-drivers-x86-v6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (128 commits)
platform/x86: Add new MeeGoPad ANX7428 Type-C Cross Switch driver
devm-helpers: Fix a misspelled cancellation in the comments
tools arch x86: Add dell-uart-backlight-emulator
platform/x86: Add new Dell UART backlight driver
platform/x86: x86-android-tablets: Create LED device for Xiaomi Pad 2 bottom bezel touch buttons
platform/x86: x86-android-tablets: Xiaomi pad2 RGB LED fwnode updates
platform/x86: x86-android-tablets: Pass struct device to init()
platform/x86/amd: pmc: Add new ACPI ID AMDI000B
platform/x86/amd: pmf: Add new ACPI ID AMDI0105
platform/x86: p2sb: Don't init until unassigned resources have been assigned
platform/surface: aggregator: Log critical errors during SAM probing
platform/x86: ISST: Support SST-BF and SST-TF per level
platform/x86/fujitsu-laptop: Replace sprintf() with sysfs_emit()
tools/power/x86/intel-speed-select: v1.19 release
tools/power/x86/intel-speed-select: Display CPU as None for -1
tools/power/x86/intel-speed-select: SST BF/TF support per level
tools/power/x86/intel-speed-select: Increase number of CPUs displayed
tools/power/x86/intel-speed-select: Present all TRL levels for turbo-freq
tools/power/x86/intel-speed-select: Fix display for unsupported levels
tools/power/x86/intel-speed-select: Support multiple dies
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD:
- Simon Glass wanted to support binman's output properties in order
to check their validity using the binding checks and proposed
changes with the missing properties as well as a binman compatible.
- Krzysztof Kozlowski on his side shared a new yaml for describing
Samsung's OneNAND interface.
- The interface with NVMEM has also been slightly improved/fixed,
especially now that OTP are also supported in the NAND subsystem.
- Along with these changes, small cleanups have also been contributed
around ID tables, structure sizes, arithmetic checks and comments.
Raw NAND subsystem:
- Two small fixes, one in the Hynix vendor code for properly
returning an error which might have been ignored and another in the
Davinci driver to properly synchronize the controller with the gpio
domain.
SPI NOR subsystem:
- SPI NOR now uses div_u64() instead of div64_u64() in places where
the divisor is 32 bits. Many 32 bit architectures can optimize this
variant better than a full 64 bit divide"
* tag 'mtd/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: replace unnecessary div64_u64() with div_u64()
mtd: mchp23k256: drop unneeded MODULE_ALIAS
dt-bindings: mtd: fixed-partition: Add binman compatibles
dt-bindings: mtd: fixed-partitions: Add alignment properties
mtd: maps: sa1100-flash: Prefer struct_size over open coded arithmetic
mtd: core: Align comment with an action in mtd_otp_nvmem_add()
mtd: rawnand: hynix: fixed typo
mtd: rawnand: davinci: Add dummy read after sending command
mtd: partitions: redboot: Added conversion of operands to a larger type
dt-bindings: mtd: Add Samsung S5Pv210 OneNAND
mtd: core: Don't fail mtd_otp_nvmem_add() if OTP is unsupported
mtd: core: Report error if first mtd_otp_size() call fails in mtd_otp_nvmem_add()
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Increase the timeout period of the ACMD41 command
- Add card entry for quirks to debugfs
- Add mmc_gpiod_set_cd_config() function
- Store owner from SDIO modules with sdio_register_driver()
MMC host:
- atmel-mci: Some cleanups and a switch to use dev_err_probe()
- renesas_sdhi:
- Add support for RZ/G2L, RZ/G3S and RZ/V2M variants
- Set the SDBUF after reset
- sdhci: Add support for "Tuning Error" interrupts
- sdhci-acpi:
- Add quirk to enable pull-up on the card-detect GPIO on Asus
T100TA
- Disable write protect detection on Toshiba WT10-A
- Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working
- sdhci_am654:
- Re-work and fix the tuning support for multiple speed-modes
- Add tuning algorithm for delay chain
- sdhci-esdhc-imx: Add NXP S32G3 support
- sdhci-of-dwcmshc:
- Add tuning support for Sophgo CV1800B and SG200X
- Implement SDHCI CQE support
- sdhci-pci-gli: Use the proper pci_set_power_state() instead of
PMCSR writes"
MEMSTICK:
- Convert a couple of drivers to use the ->remove_new() callback"
* tag 'mmc-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (59 commits)
mmc: renesas_sdhi: Add compatible string for RZ/G2L family, RZ/G3S, and RZ/V2M SoCs
dt-bindings: mmc: renesas,sdhi: Document RZ/G2L family compatibility
dt-bindings: mmc: renesas,sdhi: Group single const value items into an enum list
mmc: renesas_sdhi: Set the SDBUF after reset
mmc: core: Increase the timeout period of the ACMD41 command
mmc: core: Convert to use __mmc_poll_for_busy() SD_APP_OP_COND too
mmc: atmel-mci: Switch to use dev_err_probe()
mmc: atmel-mci: Incapsulate used to be a platform data into host structure
mmc: atmel-mci: Replace platform device pointer by generic one
mmc: atmel-mci: Use temporary variable for struct device
mmc: atmel-mci: Get rid of platform data leftovers
mmc: sdhci-of-dwcmshc: Add tuning support for Sophgo CV1800B and SG200X
mmc: sdhci-of-dwcmshc: Remove useless "&" of th1520_execute_tuning
mmc: sdhci-s3c: Choose sdhci_ops based on variant
mmc: sdhci_am654: Constify struct sdhci_ops
mmc: sdhci-sprd: Constify struct sdhci_ops
mmc: sdhci-omap: Constify struct sdhci_ops
mmc: sdhci-esdhc-mcf: Constify struct sdhci_ops
mmc: slot-gpio: Use irq_handler_t type
mmc: sdhci-acpi: Add quirk to enable pull-up on the card-detect GPIO on Asus T100TA
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain updates from Ulf Hansson:
"pmdomain core:
- Don't clear suspended_count at genpd_prepare()
- Update the rejected/usage counters at system suspend too
pmdomain providers:
- ti-sci: Fix duplicate PD referrals
- mediatek: Add MT8188 buck isolation setting
- renesas: Add R-Car M3-W power-off delay quirk
- renesas: Split R-Car M3-W and M3-W+ sub-drivers
cpuidle-psci:
- Update MAINTAINERS to set a git for DT IDLE PM DOMAIN/ARM PSCI PM
DOMAIN
- Update init level to core_initcall()
- Drop superfluous wrappers psci_dt_attach|detach_cpu()"
* tag 'pmdomain-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
pmdomain: ti-sci: Fix duplicate PD referrals
pmdomain: core: Don't clear suspended_count at genpd_prepare()
pmdomain: core: Update the rejected/usage counters at system suspend too
pmdomain: renesas: rcar-sysc: Add R-Car M3-W power-off delay quirk
pmdomain: renesas: rcar-sysc: Remove rcar_sysc_nullify() helper
pmdomain: renesas: rcar-sysc: Split R-Car M3-W and M3-W+ sub-drivers
pmdomain: renesas: rcar-sysc: Absorb rcar_sysc_ch into rcar_sysc_pd
MAINTAINERS: Add a git for the DT IDLE PM DOMAIN
MAINTAINERS: Add a git for the ARM PSCI PM DOMAIN
cpuidle: psci: Update init level to core_initcall()
cpuidle: psci: Drop superfluous wrappers psci_dt_attach|detach_cpu()
pmdomain: mediatek: Add MT8188 buck isolation setting
pmdomain: mediatek: scpsys: drop driver owner assignment
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New V4L2 ioctl VIDIOC_REMOVE_BUFS
- experimental support for using generic metaformats on V4L2 core
- New drivers: Intel IPU6 controller driver, Broadcom BCM283x/BCM271x
- More cleanups at atomisp driver
- Usual bunch of driver cleanups, improvements and fixes
* tag 'media/v6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (328 commits)
media: bcm2835-unicam: Depend on COMMON_CLK
Revert "media: v4l2-ctrls: show all owned controls in log_status"
media: ov2740: Ensure proper reset sequence on probe()
media: intel/ipu6: Don't print user-triggerable errors to kernel log
media: bcm2835-unicam: Fix driver path in MAINTAINERS
media: bcm2835-unicam: Fix a NULL vs IS_ERR() check
media: bcm2835-unicam: Do not print error when irq not found
media: bcm2835-unicam: Do not replace IRQ retcode during probe
media: bcm2835-unicam: Convert to platform remove callback returning void
media: media: intel/ipu6: Fix spelling mistake "remappinp" -> "remapping"
media: intel/ipu6: explicitly include vmalloc.h
media: cec.h: Fix kerneldoc
media: uvcvideo: Refactor iterators
media: v4l: async: refactor v4l2_async_create_ancillary_links
media: intel/ipu6: Don't re-allocate memory for firmware
media: dvb-frontends: tda10048: Fix integer overflow
media: tc358746: Use the correct div_ function
media: i2c: st-mipid02: Use the correct div function
media: tegra-vde: Refactor timeout handling
media: stk1160: Use min macro
...
|
|
Pull drm fix from Dave Airlie:
- fix breakage in buddy allocator
* tag 'drm-next-2024-05-16' of https://gitlab.freedesktop.org/drm/kernel:
drm/tests: Add a unit test for range bias allocation
drm/buddy: Fix the range bias clear memory allocation issue
|
|
A few of the ROHM PMICs allow setting low-power state specific voltages
for regulators. These voltages are then taken in use (by the hardware)
when the PMIC state is changed.
The voltages for these states can be given via device-tree. If
unsupported voltage has been given, the users have only seen print:
"driver callback failed to parse DT for regulator <name>". This does
help to pinpoint the problem to some extent, but there may be several
properties in device-tree so it should help if we can be a bit more
specific.
Print the voltage value and the run-state property if voltage can not be
supported.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://msgid.link/r/0937411855967cbefd9ff2d6045a52ca26712c4a.1715848512.git.mazziesaccount@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some of the regulators on the BD71828 have common voltage setting for
RUN/SUSPEND/IDLE/LPSR states. The enable control can be set for each
state though.
The driver allows setting the voltage values for these states via
device-tree. As a side effect, setting the voltages for
SUSPEND/IDLE/LPSR will also change the RUN level voltage which is not
desired and can break the system.
The comment in code reflects this behaviour, but it is likely to not
make people any happier. The right thing to do is to allow setting the
enable/disable state at SUSPEND/IDLE/LPSR via device-tree, but to
disallow setting state specific voltages for those regulators.
BUCK1 is a bit different. It only shares the SUSPEND and LPSR state
voltages. The former behaviour of allowing to silently overwrite the
SUSPEND state voltage by LPSR state voltage is also changed here so that
the SUSPEND voltage is prioritized over LPSR voltage.
Prevent setting PMIC state specific voltages for regulators which do not
support it.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: 522498f8cb8c ("regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators")
Link: https://msgid.link/r/e1883ae1e3ae5668f1030455d4750923561f3d68.1715848512.git.mazziesaccount@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
Raw NAND:
Two small fixes, one in the Hynix vendor code for properly returning an
error which might have been ignored and another in the Davinci driver to
properly synchronize the controller with the gpio domain.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI NOR now uses div_u64() instead of div64_u64() in places where the
divisor is 32 bits. Many 32 bit architectures can optimize this variant
better than a full 64 bit divide.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
A debugfs directory entry is create early during probe(). This entry is
not removed on error path leading to some "already present" issues in
case of EPROBE_DEFER.
Create this entry later in the probe() code to avoid the need to change
many 'return' in 'goto' and add the removal in the already present error
path.
Fixes: 942814840127 ("net: lan966x: Add VCAP debugFS support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpudata memory from kzalloc() in amd_pstate_epp_cpu_init() is
not freed in the analogous exit function, so fix that.
Signed-off-by: Peng Ma <andypma@tencent.com>
Acked-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Perry Yuan <Perry.Yuan@amd.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
With the mentioned commit (see the fixes tag) on every AP bus scan an
uevent "AP bus change bindings complete" is emitted. Furthermore if an AP
device switched from one driver to another, for example by manipulating the
apmask, there was never a "bindings complete" uevent generated.
The "bindings complete" event should be sent once when all AP devices have
been bound to device drivers and again if unbind/bind actions take place
and finally all AP devices are bound again. Therefore implement this.
Fixes: 778412ab915d ("s390/ap: rearm APQNs bindings complete completion")
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
A system crash like this
Failing address: 200000cb7df6f000 TEID: 200000cb7df6f403
Fault in home space mode while using kernel ASCE.
AS:00000002d71bc007 R3:00000003fe5b8007 S:000000011a446000 P:000000015660c13d
Oops: 0038 ilc:3 [#1] PREEMPT SMP
Modules linked in: mlx5_ib ...
CPU: 8 PID: 7556 Comm: bash Not tainted 6.9.0-rc7 #8
Hardware name: IBM 3931 A01 704 (LPAR)
Krnl PSW : 0704e00180000000 0000014b75e7b606 (ap_parse_bitmap_str+0x10e/0x1f8)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
Krnl GPRS: 0000000000000001 ffffffffffffffc0 0000000000000001 00000048f96b75d3
000000cb00000100 ffffffffffffffff ffffffffffffffff 000000cb7df6fce0
000000cb7df6fce0 00000000ffffffff 000000000000002b 00000048ffffffff
000003ff9b2dbc80 200000cb7df6fcd8 0000014bffffffc0 000000cb7df6fbc8
Krnl Code: 0000014b75e7b5fc: a7840047 brc 8,0000014b75e7b68a
0000014b75e7b600: 18b2 lr %r11,%r2
#0000014b75e7b602: a7f4000a brc 15,0000014b75e7b616
>0000014b75e7b606: eb22d00000e6 laog %r2,%r2,0(%r13)
0000014b75e7b60c: a7680001 lhi %r6,1
0000014b75e7b610: 187b lr %r7,%r11
0000014b75e7b612: 84960021 brxh %r9,%r6,0000014b75e7b654
0000014b75e7b616: 18e9 lr %r14,%r9
Call Trace:
[<0000014b75e7b606>] ap_parse_bitmap_str+0x10e/0x1f8
([<0000014b75e7b5dc>] ap_parse_bitmap_str+0xe4/0x1f8)
[<0000014b75e7b758>] apmask_store+0x68/0x140
[<0000014b75679196>] kernfs_fop_write_iter+0x14e/0x1e8
[<0000014b75598524>] vfs_write+0x1b4/0x448
[<0000014b7559894c>] ksys_write+0x74/0x100
[<0000014b7618a440>] __do_syscall+0x268/0x328
[<0000014b761a3558>] system_call+0x70/0x98
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<0000014b75e7b636>] ap_parse_bitmap_str+0x13e/0x1f8
Kernel panic - not syncing: Fatal exception: panic_on_oops
occured when /sys/bus/ap/a[pq]mask was updated with a relative mask value
(like +0x10-0x12,+60,-90) with one of the numeric values exceeding INT_MAX.
The fix is simple: use unsigned long values for the internal variables. The
correct checks are already in place in the function but a simple int for
the internal variables was used with the possibility to overflow.
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Tested-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Allocate cleared blocks in the bias range when the DRM
buddy's clear avail is zero. This will validate the bias
range allocation in scenarios like system boot when no
cleared blocks are available and exercise the fallback
path too. The resulting blocks should always be dirty.
v1:(Matthew)
- move the size to the variable declaration section.
- move the mm.clear_avail init to allocator init.
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240514145636.16253-2-Arunpravin.PaneerSelvam@amd.com
|
|
Problem statement: During the system boot time, an application request
for the bulk volume of cleared range bias memory when the clear_avail
is zero, we dont fallback into normal allocation method as we had an
unnecessary clear_avail check which prevents the fallback method leads
to fb allocation failure following system goes into unresponsive state.
Solution: Remove the unnecessary clear_avail check in the range bias
allocation function.
v2: add a kunit for this corner case (Daniel Vetter)
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Fixes: 96950929eb23 ("drm/buddy: Implement tracking clear page feature")
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240514145636.16253-1-Arunpravin.PaneerSelvam@amd.com
|
|
This reverts commit 810531a1af5393f010d6508b1cb48e6650fc5e8f.
IMS (Interrupt Message Store) support appeared in v6.2, but there are no
users yet.
Remove it for now. We can add it back when a user comes along.
Link: https://lore.kernel.org/r/20240410221307.2162676-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This reverts commit fa5745aca1dc819aee6463a2475b5c277f7cf8f6.
IMS (Interrupt Message Store) support appeared in v6.2, but there are no
users yet.
Remove it for now. We can add it back when a user comes along.
Link: https://lore.kernel.org/r/20240410221307.2162676-5-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This reverts commit 0194425af0c87acaad457989a2c6d90dba58e776.
IMS (Interrupt Message Store) support appeared in v6.2, but there are no
users yet.
Remove it for now. We can add it back when a user comes along. If this is
re-added later, the relevant part of 41efa431244f ("PCI/MSI: Provide stubs
for IMS functions") should be squashed into it.
Link: https://lore.kernel.org/r/20240410221307.2162676-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This reverts commit c9e5bea273834a63b5e9ba90ad94b305ba50704e.
IMS (Interrupt Message Store) support appeared in v6.2, but there are no
users yet.
Remove it for now. We can add it back when a user comes along. If this is
re-added later, the relevant part of 41efa431244f ("PCI/MSI: Provide stubs
for IMS functions") should be squashed into it.
Link: https://lore.kernel.org/r/20240410221307.2162676-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Pull KVM updates from Paolo Bonzini:
"ARM:
- Move a lot of state that was previously stored on a per vcpu basis
into a per-CPU area, because it is only pertinent to the host while
the vcpu is loaded. This results in better state tracking, and a
smaller vcpu structure.
- Add full handling of the ERET/ERETAA/ERETAB instructions in nested
virtualisation. The last two instructions also require emulating
part of the pointer authentication extension. As a result, the trap
handling of pointer authentication has been greatly simplified.
- Turn the global (and not very scalable) LPI translation cache into
a per-ITS, scalable cache, making non directly injected LPIs much
cheaper to make visible to the vcpu.
- A batch of pKVM patches, mostly fixes and cleanups, as the
upstreaming process seems to be resuming. Fingers crossed!
- Allocate PPIs and SGIs outside of the vcpu structure, allowing for
smaller EL2 mapping and some flexibility in implementing more or
less than 32 private IRQs.
- Purge stale mpidr_data if a vcpu is created after the MPIDR map has
been created.
- Preserve vcpu-specific ID registers across a vcpu reset.
- Various minor cleanups and improvements.
LoongArch:
- Add ParaVirt IPI support
- Add software breakpoint support
- Add mmio trace events support
RISC-V:
- Support guest breakpoints using ebreak
- Introduce per-VCPU mp_state_lock and reset_cntx_lock
- Virtualize SBI PMU snapshot and counter overflow interrupts
- New selftests for SBI PMU and Guest ebreak
- Some preparatory work for both TDX and SNP page fault handling.
This also cleans up the page fault path, so that the priorities of
various kinds of fauls (private page, no memory, write to read-only
slot, etc.) are easier to follow.
x86:
- Minimize amount of time that shadow PTEs remain in the special
REMOVED_SPTE state.
This is a state where the mmu_lock is held for reading but
concurrent accesses to the PTE have to spin; shortening its use
allows other vCPUs to repopulate the zapped region while the zapper
finishes tearing down the old, defunct page tables.
- Advertise the max mappable GPA in the "guest MAXPHYADDR" CPUID
field, which is defined by hardware but left for software use.
This lets KVM communicate its inability to map GPAs that set bits
51:48 on hosts without 5-level nested page tables. Guest firmware
is expected to use the information when mapping BARs; this avoids
that they end up at a legal, but unmappable, GPA.
- Fixed a bug where KVM would not reject accesses to MSR that aren't
supposed to exist given the vCPU model and/or KVM configuration.
- As usual, a bunch of code cleanups.
x86 (AMD):
- Implement a new and improved API to initialize SEV and SEV-ES VMs,
which will also be extendable to SEV-SNP.
The new API specifies the desired encryption in KVM_CREATE_VM and
then separately initializes the VM. The new API also allows
customizing the desired set of VMSA features; the features affect
the measurement of the VM's initial state, and therefore enabling
them cannot be done tout court by the hypervisor.
While at it, the new API includes two bugfixes that couldn't be
applied to the old one without a flag day in userspace or without
affecting the initial measurement. When a SEV-ES VM is created with
the new VM type, KVM_GET_REGS/KVM_SET_REGS and friends are rejected
once the VMSA has been encrypted. Also, the FPU and AVX state will
be synchronized and encrypted too.
- Support for GHCB version 2 as applicable to SEV-ES guests.
This, once more, is only accessible when using the new
KVM_SEV_INIT2 flow for initialization of SEV-ES VMs.
x86 (Intel):
- An initial bunch of prerequisite patches for Intel TDX were merged.
They generally don't do anything interesting. The only somewhat
user visible change is a new debugging mode that checks that KVM's
MMU never triggers a #VE virtualization exception in the guest.
- Clear vmcs.EXIT_QUALIFICATION when synthesizing an EPT Misconfig
VM-Exit to L1, as per the SDM.
Generic:
- Use vfree() instead of kvfree() for allocations that always use
vcalloc() or __vcalloc().
- Remove .change_pte() MMU notifier - the changes to non-KVM code are
small and Andrew Morton asked that I also take those through the
KVM tree.
The callback was only ever implemented by KVM (which was also the
original user of MMU notifiers) but it had been nonfunctional ever
since calls to set_pte_at_notify were wrapped with
invalidate_range_start and invalidate_range_end... in 2012.
Selftests:
- Enhance the demand paging test to allow for better reporting and
stressing of UFFD performance.
- Convert the steal time test to generate TAP-friendly output.
- Fix a flaky false positive in the xen_shinfo_test due to comparing
elapsed time across two different clock domains.
- Skip the MONITOR/MWAIT test if the host doesn't actually support
MWAIT.
- Avoid unnecessary use of "sudo" in the NX hugepage test wrapper
shell script, to play nice with running in a minimal userspace
environment.
- Allow skipping the RSEQ test's sanity check that the vCPU was able
to complete a reasonable number of KVM_RUNs, as the assert can fail
on a completely valid setup.
If the test is run on a large-ish system that is otherwise idle,
and the test isn't affined to a low-ish number of CPUs, the vCPU
task can be repeatedly migrated to CPUs that are in deep sleep
states, which results in the vCPU having very little net runtime
before the next migration due to high wakeup latencies.
- Define _GNU_SOURCE for all selftests to fix a warning that was
introduced by a change to kselftest_harness.h late in the 6.9
cycle, and because forcing every test to #define _GNU_SOURCE is
painful.
- Provide a global pseudo-RNG instance for all tests, so that library
code can generate random, but determinstic numbers.
- Use the global pRNG to randomly force emulation of select writes
from guest code on x86, e.g. to help validate KVM's emulation of
locked accesses.
- Allocate and initialize x86's GDT, IDT, TSS, segments, and default
exception handlers at VM creation, instead of forcing tests to
manually trigger the related setup.
Documentation:
- Fix a goof in the KVM_CREATE_GUEST_MEMFD documentation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (225 commits)
selftests/kvm: remove dead file
KVM: selftests: arm64: Test vCPU-scoped feature ID registers
KVM: selftests: arm64: Test that feature ID regs survive a reset
KVM: selftests: arm64: Store expected register value in set_id_regs
KVM: selftests: arm64: Rename helper in set_id_regs to imply VM scope
KVM: arm64: Only reset vCPU-scoped feature ID regs once
KVM: arm64: Reset VM feature ID regs from kvm_reset_sys_regs()
KVM: arm64: Rename is_id_reg() to imply VM scope
KVM: arm64: Destroy mpidr_data for 'late' vCPU creation
KVM: arm64: Use hVHE in pKVM by default on CPUs with VHE support
KVM: arm64: Fix hvhe/nvhe early alias parsing
KVM: SEV: Allow per-guest configuration of GHCB protocol version
KVM: SEV: Add GHCB handling for termination requests
KVM: SEV: Add GHCB handling for Hypervisor Feature Support requests
KVM: SEV: Add support to handle AP reset MSR protocol
KVM: x86: Explicitly zero kvm_caps during vendor module load
KVM: x86: Fully re-initialize supported_mce_cap on vendor module load
KVM: x86: Fully re-initialize supported_vm_types on vendor module load
KVM: x86/mmu: Sanity check that __kvm_faultin_pfn() doesn't create noslot pfns
KVM: x86/mmu: Initialize kvm_page_fault's pfn and hva to error values
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull CXL updates from Dave Jiang:
- Three CXL mailbox passthrough commands are added to support the
populating and clearing of vendor debug logs:
- Get Log Capabilities
- Get Supported Log Sub-List Commands
- Clear Log
- Add support of Device Phyiscal Address (DPA) to Host Physical Address
(HPA) translation for CXL events of cxl_dram and cxl_general media.
This allows user space to figure out which CXL region the event
occured via trace event.
- Connect CXL to CPER reporting.
If a device is configured for firmware first, CXL event records are
not sent directly to the host. Those records are reported through EFI
Common Platform Error Records (CPER). Add support to route the CPER
records through the CXL sub-system in order to provide DPA to HPA
translation and also event decoding and tracing. This is useful for
users to determine which system issues may correspond to specific
hardware events.
- A number of misc cleanups and fixes:
- Fix for compile warning of cxl_security_ops
- Add debug message for invalid interleave granularity
- Enhancement to cxl-test event testing
- Add dev_warn() on unsupported mixed mode decoder
- Fix use of phys_to_target_node() for x86
- Use helper function for decoder enum instead of open coding
- Include missing headers for cxl-event
- Fix MAINTAINERS file entry
- Fix cxlr_pmem memory leak
- Cleanup __cxl_parse_cfmws via scope-based resource menagement
- Convert cxl_pmem_region_alloc() to scope-based resource management
* tag 'cxl-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (21 commits)
cxl/cper: Remove duplicated GUID defines
cxl/cper: Fix non-ACPI-APEI-GHES build
cxl/pci: Process CPER events
acpi/ghes: Process CXL Component Events
cxl/region: Convert cxl_pmem_region_alloc to scope-based resource management
cxl/acpi: Cleanup __cxl_parse_cfmws()
cxl/region: Fix cxlr_pmem leaks
cxl/core: Add region info to cxl_general_media and cxl_dram events
cxl/region: Move cxl_trace_hpa() work to the region driver
cxl/region: Move cxl_dpa_to_region() work to the region driver
cxl/trace: Correct DPA field masks for general_media & dram events
MAINTAINERS: repair file entry in COMPUTE EXPRESS LINK
cxl/cxl-event: include missing <linux/types.h> and <linux/uuid.h>
cxl/hdm: Debug, use decoder name function
cxl: Fix use of phys_to_target_node() for x86
cxl/hdm: dev_warn() on unsupported mixed mode decoder
cxl/test: Enhance event testing
cxl/hdm: Add debug message for invalid interleave granularity
cxl: Fix compile warning for cxl_security_ops extern
cxl/mbox: Add Clear Log mailbox command
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull nvdimm updates from Ira Weiny:
"The changes include removing duplicate code and updating the nvdimm
tree to the current kernel interfaces such as using const for struct
device_type and changing the platform remove callback signature"
* tag 'libnvdimm-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: remove redundant assignment to variable rc
ndtest: Convert to platform remove callback returning void
nvdimm/btt: always set max_integrity_segments
nvdimm: remove nd_integrity_init
dax: constify the struct device_type usage
powerpc/papr_scm: Move duplicate definitions to common header files
|
|
Remove wrong mask on subsys_vendor_id. Both the Vendor ID and Subsystem
Vendor ID are u16 variables and are written to a u32 register of the
controller. The Subsystem Vendor ID was always 0 because the u16 value
was masked incorrectly with GENMASK(31,16) resulting in all lower 16
bits being set to 0 prior to the shift.
Remove both masks as they are unnecessary and set the register correctly
i.e., the lower 16-bits are the Vendor ID and the upper 16-bits are the
Subsystem Vendor ID.
This is documented in the RK3399 TRM section 17.6.7.1.17
[kwilczynski: removed unnecesary newline]
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Link: https://lore.kernel.org/linux-pci/20240403144508.489835-1-rick.wertenbroek@gmail.com
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Use no_printk() instead of "if (0) printk()" constructs to avoid
generating printk index for messages disabled at compile time
- Remove deprecated strncpy/strcpy from printk.c
- Remove redundant CONFIG_BASE_FULL in favor of CONFIG_BASE_SMALL
* tag 'printk-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: cleanup deprecated uses of strncpy/strcpy
printk: Remove redundant CONFIG_BASE_FULL
printk: Change type of CONFIG_BASE_SMALL to bool
printk: Fix LOG_CPU_MAX_BUF_SHIFT when BASE_SMALL is enabled
ceph: Use no_printk() helper
dyndbg: Use *no_printk() helpers
dev_printk: Add and use dev_no_printk()
printk: Let no_printk() use _printk()
|
|
When running syzkaller with the newly reintroduced signed integer wrap
sanitizer we encounter this splat:
[ 366.015950] UBSAN: signed-integer-overflow in ../drivers/cdrom/cdrom.c:2361:33
[ 366.021089] -9223372036854775808 - 346321 cannot be represented in type '__s64' (aka 'long long')
[ 366.025894] program syz-executor.4 is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 366.027502] CPU: 5 PID: 28472 Comm: syz-executor.7 Not tainted 6.8.0-rc2-00035-gb3ef86b5a957 #1
[ 366.027512] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[ 366.027518] Call Trace:
[ 366.027523] <TASK>
[ 366.027533] dump_stack_lvl+0x93/0xd0
[ 366.027899] handle_overflow+0x171/0x1b0
[ 366.038787] ata1.00: invalid multi_count 32 ignored
[ 366.043924] cdrom_ioctl+0x2c3f/0x2d10
[ 366.063932] ? __pm_runtime_resume+0xe6/0x130
[ 366.071923] sr_block_ioctl+0x15d/0x1d0
[ 366.074624] ? __pfx_sr_block_ioctl+0x10/0x10
[ 366.077642] blkdev_ioctl+0x419/0x500
[ 366.080231] ? __pfx_blkdev_ioctl+0x10/0x10
...
Historically, the signed integer overflow sanitizer did not work in the
kernel due to its interaction with `-fwrapv` but this has since been
changed [1] in the newest version of Clang. It was re-enabled in the
kernel with Commit 557f8c582a9ba8ab ("ubsan: Reintroduce signed overflow
sanitizer").
Let's rearrange the check to not perform any arithmetic, thus not
tripping the sanitizer.
Link: https://github.com/llvm/llvm-project/pull/82432 [1]
Closes: https://github.com/KSPP/linux/issues/354
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Justin Stitt <justinstitt@google.com>
Link: https://lore.kernel.org/lkml/20240507-b4-sio-ata1-v1-1-810ffac6080a@google.com
Reviewed-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/lkml/ZjqU0fbzHrlnad8D@equinox
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20240507222520.1445-2-phil@philpotter.co.uk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
