| Age | Commit message (Collapse) | Author |
|---|
|
To be consistent with the usual "get_resources" naming of driver
functions that acquire controller resources like clocks, PHY etc,
rename the function rockchip_pcie_parse_ep_dt() to
rockchip_pcie_ep_get_resources().
No functional changes.
Link: https://lore.kernel.org/r/20241017015849.190271-8-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The call to rockchip_pcie_prog_ep_ob_atu() used to map the PCI address
of MSI data to the memory window allocated on probe for IRQs is done
in rockchip_pcie_ep_send_msi_irq() assuming a fixed alignment to a
256B boundary of the PCI address. This is not correct as the alignment
constraint for the RK3399 PCI mapping depends on the number of bits of
address changing in the mapped region. This leads to an unstable system
which sometimes work and sometimes does not (crashing on paging faults
when memcpy_toio() or memcpy_fromio() are used).
Similar to regular data mapping, the MSI data mapping must thus be
handled according to the information provided by
rockchip_pcie_ep_align_addr(). Modify rockchip_pcie_ep_send_msi_irq()
to use rockchip_pcie_ep_align_addr() to correctly program entry 0 of
the ATU for sending MSI IRQs.
Link: https://lore.kernel.org/r/20241017015849.190271-7-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits from the CPU address space used for the
mapping. For a PCI mapping of size bytes starting from pci_addr, the
number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1], up to 20 bits, that is,
up to 1MB mappings.
This means that when preparing a PCI address mapping, an endpoint
function driver must use an offset into the allocated controller
memory region that is equal to the mask of the starting PCI address
over rockchip_pcie_ep_ob_atu_num_bits() bits. This offset also
determines the maximum size of the mapping given the starting PCI
address and the fixed 1MB controller memory window size.
Implement the ->align_addr() endpoint controller operation to allow the
mapping alignment to be transparently handled by endpoint function
drivers through the function pci_epc_mem_map().
Link: https://lore.kernel.org/r/20241017015849.190271-6-dlemoal@kernel.org
Co-developed-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: change local variable name for address offset]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add a check to verify that the outbound region to be used for mapping an
address is not already in use.
Link: https://lore.kernel.org/r/20241017015849.190271-5-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
There is no need to loop over all regions to find the memory window used
to map an address. We can use rockchip_ob_region() to determine the
region index, together with a check that the address passed as argument
is the address used to create the mapping. Furthermore, the
ob_region_map bitmap should also be checked to ensure that we are not
attempting to unmap an address that is not mapped.
Link: https://lore.kernel.org/r/20241017015849.190271-4-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Introduce the macro ROCKCHIP_PCIE_AT_SIZE_ALIGN to initialize the .align
field of the controller epc_features structure to 256. This is defined
as a shift using the macro ROCKCHIP_PCIE_AT_MIN_NUM_BITS (to avoid
using the "magic" value 8 directly).
Link: https://lore.kernel.org/r/20241017015849.190271-3-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits masked from the CPU address space used for the
mapping. For a PCI mapping of <size> bytes starting from <pci_addr>,
the number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1].
However, rockchip_pcie_prog_ep_ob_atu() calculates num_pass_bits only
using the size of the mapping, resulting in an incorrect number of mask
bits depending on the value of the PCI address to map.
Fix this by introducing the helper function
rockchip_pcie_ep_ob_atu_num_bits() to correctly calculate the number of
mask bits to use to program the address translation unit. The number of
mask bits is calculated depending on both the PCI address and size of
the mapping, and clamped between 8 and 20 using the macros
ROCKCHIP_PCIE_AT_MIN_NUM_BITS and ROCKCHIP_PCIE_AT_MAX_NUM_BITS. As
defined in the Rockchip RK3399 TRM V1.3 Part2, Sections 17.5.5.1.1 and
17.6.8.2.1, this clamping is necessary because:
1) The lower 8 bits of the PCI address to be mapped by the outbound
region are ignored. So a minimum of 8 address bits are needed and
imply that the PCI address must be aligned to 256.
2) The outbound memory regions are 1MB in size. So while we can specify
up to 63-bits for the PCI address (num_bits filed uses bits 0 to 5 of
the outbound address region 0 register), we must limit the number of
valid address bits to 20 to match the memory window maximum size (1
<< 20 = 1MB).
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Link: https://lore.kernel.org/r/20241017015849.190271-2-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
|
|
The portid_bits and deviceid_bits were set only for XP type nodes in
the arm_cmn_discover() and it confused other nodes to find XP nodes.
Copy the both bits from the XP nodes directly when it sets up a new
node.
Fixes: e79634b53e39 ("perf/arm-cmn: Refactor node ID handling. Again.")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20241121001334.331334-1-namhyung@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Same as
https://lore.kernel.org/all/20240514180050.182454-1-namhyung@kernel.org/,
we should skip `for_each_sibling_event()` for group leader since it
doesn't have the ctx yet.
Fixes: f3c0eba28704 ("perf: Add a few assertions")
Reported-by: Greg Thelen <gthelen@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Tuan Phan <tuanphan@os.amperecomputing.com>
Signed-off-by: Chun-Tse Shao <ctshao@google.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20241108050806.3730811-1-ctshao@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- support for NT36672A touchscreen added to novatek-nvt-ts driver
- a change to ads7846 driver to prevent XPT2046 from locking up
- a change switching platform input dirves back to using remove()
method (from remove_new())
- updates to a number of input drivers to use the new cleanup
facilities (__free(...), guard(), and scoped-guard()) which ensure
that the resources and locks are released properly and automatically
- other assorted driver cleanups and fixes.
* tag 'input-for-v6.13-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (109 commits)
Input: mpr121 - use devm_regulator_get_enable_read_voltage()
Input: sun4i-lradc-keys - don't include 'pm_wakeup.h' directly
Input: spear-keyboard - don't include 'pm_wakeup.h' directly
Input: cypress-sf - constify struct i2c_device_id
Input: ads7846 - increase xfer array size in 'struct ser_req'
Input: fix the input_event struct documentation
Input: i8042 - fix typo dublicate to duplicate
Input: ads7846 - add dummy command register clearing cycle
Input: cs40l50 - fix wrong usage of INIT_WORK()
Input: introduce notion of passive observers for input handlers
Input: maple_keyb - use guard notation when acquiring mutex
Input: locomokbd - use guard notation when acquiring spinlock
Input: hilkbd - use guard notation when acquiring spinlock
Input: synaptics-rmi4 - switch to using cleanup functions in F34
Input: synaptics - fix a typo
dt-bindings: input: rotary-encoder: Fix "rotary-encoder,rollover" type
Input: omap-keypad - use guard notation when acquiring mutex
Input: imagis - fix warning regarding 'imagis_3038_data' being unused
Input: userio - remove unneeded semicolon
Input: sparcspkr - use cleanup facility for device_node
...
|
|
This reverts commit 6fd47effe92b, and the related self-test update
commit e14e0eaeb040 ("selftests/hid: add test for assigning a given
device to hid-generic").
It results in things like the scroll wheel on Logitech mice not working
after a reboot due to the kernel being confused about the state of the
high-resolution mode.
Quoting Benjamin Tissoires:
"The idea of 6fd47effe92b was to be able to call hid_bpf_rdesc_fixup()
once per reprobe of the device.
However, because the bpf filter can now change the quirk value, the
call had to be moved before the driver gets bound (which was
previously ensuring the unicity of the call).
The net effect is that now, in the case hid-generic gets loaded first
and then the specific driver gets loaded once the disk is available,
the value of ->quirks is not reset, but kept to the value that was set
by hid-generic (HID_QUIRK_INPUT_PER_APP).
Once hid-logitech-hidpp kicks in, that quirk is now set, which creates
two inputs for the single mouse: one keyboard for fancy shortcuts, and
one mouse node.
However, hid-logitech-hidpp expects only one input node to be attached
(it stores it into hidpp->input), and when a wheel event is received,
because there is some processing with high-resolution wheel events,
the wheel event is injected into hidpp->input.
And of course, when HID_QUIRK_INPUT_PER_APP is set, hidpp->input gets
the keyboard node, which doesn't have wheel event type, and the events
are ignored"
Reported-and-bisected-by: Mike Galbraith <efault@gmx.de>
Link: https://lore.kernel.org/all/CAHk-=wiUkQM3uheit2cNM0Y0OOY5qqspJgC8LkmOkJ2p2LDxcw@mail.gmail.com/
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are cases where a PCIe extended capability should be hidden from
the user. For example, an unknown capability (i.e., capability with ID
greater than PCI_EXT_CAP_ID_MAX) or a capability that is intentionally
chosen to be hidden from the user.
Hiding a capability is done by virtualizing and modifying the 'Next
Capability Offset' field of the previous capability so it points to the
capability after the one that should be hidden.
The special case where the first capability in the list should be hidden
is handled differently because there is no previous capability that can
be modified. In this case, the capability ID and version are zeroed
while leaving the next pointer intact. This hides the capability and
leaves an anchor for the rest of the capability list.
However, today, hiding the first capability in the list is not done
properly if the capability is unknown, as struct
vfio_pci_core_device->pci_config_map is set to the capability ID during
initialization but the capability ID is not properly checked later when
used in vfio_config_do_rw(). This leads to the following warning [1] and
to an out-of-bounds access to ecap_perms array.
Fix it by checking cap_id in vfio_config_do_rw(), and if it is greater
than PCI_EXT_CAP_ID_MAX, use an alternative struct perm_bits for direct
read only access instead of the ecap_perms array.
Note that this is safe since the above is the only case where cap_id can
exceed PCI_EXT_CAP_ID_MAX (except for the special capabilities, which
are already checked before).
[1]
WARNING: CPU: 118 PID: 5329 at drivers/vfio/pci/vfio_pci_config.c:1900 vfio_pci_config_rw+0x395/0x430 [vfio_pci_core]
CPU: 118 UID: 0 PID: 5329 Comm: simx-qemu-syste Not tainted 6.12.0+ #1
(snip)
Call Trace:
<TASK>
? show_regs+0x69/0x80
? __warn+0x8d/0x140
? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core]
? report_bug+0x18f/0x1a0
? handle_bug+0x63/0xa0
? exc_invalid_op+0x19/0x70
? asm_exc_invalid_op+0x1b/0x20
? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core]
? vfio_pci_config_rw+0x244/0x430 [vfio_pci_core]
vfio_pci_rw+0x101/0x1b0 [vfio_pci_core]
vfio_pci_core_read+0x1d/0x30 [vfio_pci_core]
vfio_device_fops_read+0x27/0x40 [vfio]
vfs_read+0xbd/0x340
? vfio_device_fops_unl_ioctl+0xbb/0x740 [vfio]
? __rseq_handle_notify_resume+0xa4/0x4b0
__x64_sys_pread64+0x96/0xc0
x64_sys_call+0x1c3d/0x20d0
do_syscall_64+0x4d/0x120
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Fixes: 89e1f7d4c66d ("vfio: Add PCI device driver")
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Yi Liu <yi.l.liu@intel.com>
Tested-by: Yi Liu <yi.l.liu@intel.com>
Link: https://lore.kernel.org/r/20241124142739.21698-1-avihaih@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The group only contains a single entry and the conditionals around its
lifecycle make clear that this won't change.
Remove the unnecessary group.
This saves some memory and it's easier to read.
The removal of a non-const bin_attribute[] instance is also a
preparation for the constification of struct bin_attributes.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://patch.msgid.link/20241121-sysfs-const-bin_attr-int340x_thermal-v1-1-2436facf9dae@weissschuh.net
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When the current_uuid attribute is set to the active policy UUID,
reading back the same attribute is returning "INVALID" instead of
the active policy UUID on some platforms before Ice Lake.
In platforms before Ice Lake, firmware provides a list of supported
thermal policies. In this case, user space can select any of the
supported thermal policies via a write to attribute "current_uuid".
In commit c7ff29763989 ("thermal: int340x: Update OS policy capability
handshake")', the OS policy handshake was updated to support Ice Lake
and later platforms and it treated priv->current_uuid_index=0 as
invalid. However, priv->current_uuid_index=0 is for the active policy,
only priv->current_uuid_index=-1 is invalid.
Fix this issue by updating the priv->current_uuid_index check.
Fixes: c7ff29763989 ("thermal: int340x: Update OS policy capability handshake")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 5.18+ <stable@vger.kernel.org> # 5.18+
Link: https://patch.msgid.link/20241114200213.422303-1-srinivas.pandruvada@linux.intel.com
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Prepare input updates for 6.13 merge window.
|
|
VCAP API unit tests fail randomly with errors such as
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:387
Expected 134 + 7 == iter.offset, but
134 + 7 == 141 (0x8d)
iter.offset == 17214 (0x433e)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:388
Expected 5 == iter.reg_idx, but
iter.reg_idx == 702 (0x2be)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:389
Expected 11 == iter.reg_bitpos, but
iter.reg_bitpos == 15 (0xf)
# vcap_api_iterator_init_test: pass:0 fail:1 skip:0 total:1
Comments in the code state that "A typegroup table ends with an all-zero
terminator". Add the missing terminators.
Some of the typegroups did have a terminator of ".offset = 0, .width = 0,
.value = 0,". Replace those terminators with "{ }" (no trailing ',') for
consistency and to excplicitly state "this is a terminator".
Fixes: 67d637516fa9 ("net: microchip: sparx5: Adding KUNIT test for the VCAP API")
Cc: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241119213202.2884639-1-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Validate Wake-on-LAN (WoL) options in `lan78xx_set_wol` before calling
`usb_autopm_get_interface`. This prevents USB autopm refcounting issues
and ensures the adapter can properly enter autosuspend when invalid WoL
options are provided.
Fixes: eb9ad088f966 ("lan78xx: Check for supported Wake-on-LAN modes")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://patch.msgid.link/20241118140351.2398166-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The hardware on Broadcom 1G chipsets have a known limitation
where they cannot handle DMA addresses that cross over 4GB.
When such an address is encountered, the hardware sets the
address overflow error bit in the DMA status register and
triggers a reset.
However, BCM57766 hardware is setting the overflow bit and
triggering a reset in some cases when there is no actual
underlying address overflow. The hardware team analyzed the
issue and concluded that it is happening when the status
block update has an address with higher (b16 to b31) bits
as 0xffff following a previous update that had lowest bits
as 0xffff.
To work around this bug in the BCM57766 hardware, set the
coherent dma mask from the current 64b to 31b. This will
ensure that upper bits of the status block DMA address are
always at most 0x7fff, thus avoiding the improper overflow
check described above. This work around is intended for only
status block and ring memories and has no effect on TX and
RX buffers as they do not require coherent memory.
Fixes: 72f2afb8a685 ("[TG3]: Add DMA address workaround")
Reported-by: Salam Noureddine <noureddine@arista.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://patch.msgid.link/20241119055741.147144-1-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add calls to `phy_device_free` after `fixed_phy_unregister` to fix a
memory leak that occurs when the device is unplugged. This ensures
proper cleanup of pseudo fixed-link PHYs.
Fixes: 89b36fb5e532 ("lan78xx: Lan7801 Support for Fixed PHY")
Cc: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241116130558.1352230-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In lan78xx_probe(), the buffer `buf` was being freed twice: once
implicitly through `usb_free_urb(dev->urb_intr)` with the
`URB_FREE_BUFFER` flag and again explicitly by `kfree(buf)`. This caused
a double free issue.
To resolve this, reordered `kmalloc()` and `usb_alloc_urb()` calls to
simplify the initialization sequence and removed the redundant
`kfree(buf)`. Now, `buf` is allocated after `usb_alloc_urb()`, ensuring
it is correctly managed by `usb_fill_int_urb()` and freed by
`usb_free_urb()` as intended.
Fixes: a6df95cae40b ("lan78xx: Fix memory allocation bug")
Cc: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241116130558.1352230-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Type 4 PCC channels have an option to send back a response
to the platform when they are done processing the request.
The flag to indicate whether or not to respond is inside
the message body, and thus is not available to the pcc
mailbox.
If the flag is not set, still set command completion
bit after processing message.
In order to read the flag, this patch maps the shared
buffer to virtual memory. To avoid duplication of mapping
the shared buffer is then made available to be used by
the driver that uses the mailbox.
Signed-off-by: Adam Young <admiyo@os.amperecomputing.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/mailbox to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Make a few indentions consistent while touching these struct
initializers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
Replace %i with %u in snprintf() because it is "unsigned int".
Signed-off-by: zhang jiao <zhangjiao2@cmss.chinamobile.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
Both the inner and outer loops in this code use the "i" iterator.
The inner loop should really use a different iterator.
It doesn't affect things in practice because the data comes from the
device tree. The "protocol" and "windows" variables are going to be
zero. That means we're always going to hit the "return &chans[channel];"
statement and we're not going to want to iterate through the outer
loop again.
Still it's worth fixing this for future use cases.
Fixes: 5a6338cce9f4 ("mailbox: arm_mhuv2: Add driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
As per zynqmp-ipi bindings, zynqmp IPI node can have multiple child nodes.
Current IPI setup function is set only for first child node. If IPI node
has multiple child nodes in the device-tree, then IPI setup fails for
child nodes other than first child node. In such case kernel will crash.
Fix this crash by registering IPI setup function for each available child
node.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
This driver was tested using the drm/imagination GPU driver. It was able
to successfully power on the GPU, by passing a command through mailbox
from E910 core to E902 that's responsible for powering up the GPU. The
GPU driver was able to read the BVNC version from control registers,
which confirms it was successfully powered on.
[ 33.957467] powervr ffef400000.gpu: [drm] loaded firmware
powervr/rogue_36.52.104.182_v1.fw
[ 33.966008] powervr ffef400000.gpu: [drm] FW version v1.0 (build
6621747 OS)
[ 38.978542] powervr ffef400000.gpu: [drm] *ERROR* Firmware failed to
boot
Though the driver still fails to boot the firmware, the mailbox driver
works when used with the not-yet-upstreamed firmware AON driver. There
is ongoing work to get the BXM-4-64 supported with the drm/imagination
driver [1], though it's not completed yet.
This work is based on the driver from the vendor kernel [2].
Link: https://gitlab.freedesktop.org/imagination/linux-firmware/-/issues/2 [1]
Link: https://github.com/revyos/thead-kernel.git [2]
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
It should be size of the struct clk_bulk_data, not data pointer pass to
devm_kcalloc().
Fixes: aa1609f571ca ("mailbox: mtk-cmdq: Dynamically allocate clk_bulk_data structure")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
The TI message manager driver can be compiled without ARCH_KEYSTONE
nor ARCH_K3 enabled. Allow it to be built under COMPILE_TEST.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
When OF support is disabled the of_device_id struct match table can be
conditionally compiled out, this helper allows the assignment to also be
turned into a NULL conditionally. When the of_device_id struct is not
conditionally defined based on OF then the table will be unused causing a
warning. The two options are to either set the table as _maybe_unused, or
to just remove this helper since the table will always be defined.
Do the latter here.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
The qcom-cpucp mailbox irq is expected to function during suspend-resume
cycle particularly when the scmi cpufreq driver can query the current
frequency using the get_level message after the cpus are brought up during
resume. Hence mark the irq with IRQF_NO_SUSPEND flag to fix the do_xfer
failures we see during resume.
Err Logs:
arm-scmi firmware:scmi: timed out in resp(caller:do_xfer+0x164/0x568)
cpufreq: cpufreq_online: ->get() failed
Reported-by: Johan Hovold <johan+linaro@kernel.org>
Closes: https://lore.kernel.org/lkml/ZtgFj1y5ggipgEOS@hovoldconsulting.com/
Fixes: 0e2a9a03106c ("mailbox: Add support for QTI CPUCP mailbox controller")
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
pm_runtime_put_autosuspend() will soon be changed to include a call to
pm_runtime_mark_last_busy(). This patch switches the current users to
__pm_runtime_put_autosuspend() which will continue to have the
functionality of old pm_runtime_put_autosuspend().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
The two previous bindings for this hardware were incorrect, as the
control/status and interrupt register regions should have been described
as syscons and dealt with via regmap in the driver. Add support for
accessing these registers using that method now, so that the hwmon
driver can be supported without using auxdev or hacks with io_remap().
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
Commit 120584c728a6 ("hwmon: (aquacomputer_d5next) Add support for Octo
flow sensor") added support for reading Octo flow sensor, but didn't
update the priv->speed_input array length. Since Octo has 8 fans, with
the addition of the flow sensor the proper length for speed_input is 9.
Reported by Arne Schwabe on Github [1], who received a UBSAN warning.
Fixes: 120584c728a6 ("hwmon: (aquacomputer_d5next) Add support for Octo flow sensor")
Closes: https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/100 [1]
Reported-by: Arne Schwabe <arne@rfc2549.org>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Message-ID: <20241124152725.7205-1-savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
In commit 35eba185fd1a ("i2c: designware: Calculate SCL timing parameter
for High Speed Mode") the SCL high period count and low period count for
high speed mode are calculated based on fixed tHIGH = 160 and tLOW = 120.
However, the set of two fixed values is only applicable to the combination
of hardware parameters IC_CAP_LOADING is 400 and IC_CLK_FREQ_OPTIMIZATION
is true. Outside of this combination, the SCL frequency may not reach
3.4 MHz because the fixed tHIGH and tLOW are not small enough.
If IC_CAP_LOADING is 400, it means the bus capacitance is 400pF;
Otherwise, 100 pF. If IC_CLK_FREQ_OPTIMIZATION is true, it means that the
hardware reduces its internal clock frequency by reducing the internal
latency required to generate the high period and low period of the SCL line.
Section 3.15.4.5 in DesignWare DW_apb_i2b Databook v2.03 says that when
IC_CLK_FREQ_OPTIMIZATION = 0,
MIN_SCL_HIGHtime = 60 ns for 3.4 Mbps, bus loading = 100pF
= 120 ns for 3.4 Mbps, bus loading = 400pF
MIN_SCL_LOWtime = 160 ns for 3.4 Mbps, bus loading = 100pF
= 320 ns for 3.4 Mbps, bus loading = 400pF
and section 3.15.4.6 says that when IC_CLK_FREQ_OPTIMIZATION = 1,
MIN_SCL_HIGHtime = 60 ns for 3.4 Mbps, bus loading = 100pF
= 160 ns for 3.4 Mbps, bus loading = 400pF
MIN_SCL_LOWtime = 120 ns for 3.4 Mbps, bus loading = 100pF
= 320 ns for 3.4 Mbps, bus loading = 400pF
In order to calculate more accurate SCL high period count and low period
count for high speed mode, two hardware parameters IC_CAP_LOADING and
IC_CLK_FREQ_OPTIMIZATION must be considered together. Since there're no
registers controlliing these these two hardware parameters, users can
declare them in the device tree so that the driver can obtain them.
Signed-off-by: Michael Wu <michael.wu@kneron.us>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
- BRCR value must go into the BRCR1 field when in high-speed mode.
It goes into BRCR2 otherwise.
- Remove fallback to standard mode if priv->sm > I2C_FREQ_MODE_FAST.
- Set SM properly in probe; previously it only checked STANDARD versus
FAST. Now we set STANDARD, FAST, FAST_PLUS or HIGH_SPEED.
- Remove all comment sections saying we only support low-speeds.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Current BRCR computation is:
brcr = floor(i2cclk / (clkfreq * div))
With brcr: "baud rate counter", an internal clock divider,
and i2cclk: input clock rate (24MHz, 38.4MHz or 48MHz),
and clkfreq: desired bus rate,
and div: speed-mode dependent divider (2 for standard, 3 otherwise).
Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
then brcr = floor(48MHz / (3.4MHz * 3)) = 4
and resulting bus rate = 48MHz / (4 * 3) = 4MHz
Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
then brcr = floor(38.4MHz / (1.0MHz * 3)) = 12
and resulting bus rate = 38.4MHz / (12 * 3) = 1066kHz
The current computation means we always pick the smallest divider that
gives a bus rate above target. We should instead pick the largest
divider that gives a bus rate below target, using:
brcr = floor(i2cclk / (clkfreq * div)) + 1
If we redo the above examples:
Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
then brcr = floor(48MHz / (3.4MHz * 3)) + 1 = 5
and resulting bus rate = 48MHz / (5 * 3) = 3.2MHz
Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
then brcr = floor(38.4MHz / (1.0MHz * 3)) + 1 = 13
and resulting bus rate = 38.4MHz / (13 * 3) = 985kHz
In kernel C code, floor(x) is DIV_ROUND_DOWN() and,
floor(x)+1 is DIV_ROUND_UP().
This is much less of an issue with slower bus rates (ie those currently
supported), because the gap from one divider to the next is much
smaller. It however keeps us from always using bus rates superior to
the target.
This fix is required for later on supporting faster bus rates:
I2C_FREQ_MODE_FAST_PLUS (1MHz) and I2C_FREQ_MODE_HIGH_SPEED (3.4MHz).
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Add EyeQ6H support to the nmk-i2c AMBA driver. It shares the same quirk
as EyeQ5: the memory bus only supports 32-bit accesses. Avoid writeb()
and readb() by reusing the same `priv->has_32b_bus` flag.
It does NOT need to write speed-mode specific value into a register;
therefore it does not depend on the mobileye,olb DT property.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Compatible-specific behavior is implemented using a if-condition on the
return value from of_device_is_compatible(), from probe. It does not
scale well when compatible number increases. Switch to using a match
table and a call to of_match_device().
We DO NOT attach a .of_match_table field to our amba driver, as we do
not use the table to match our driver to devices.
Sort probe variable declarations in reverse christmas tree to try and
introduce some logic into the ordering.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Enable DWAPB I2C controller support on FUJITSU-MONAKA.
This will be used in the FUJITSU-MONAKA server scheduled
for shipment in 2027.
The DSDT information obtained when verified using an
in-house simulator is presented below.
Device (SMB0)
{
Name (_HID, "FUJI200B") // _HID: Hardware ID
Name (_UID, Zero) // _UID: Unique ID
...
Name (_CRS, ResourceTemplate ()
{
Memory32Fixed (ReadWrite,
0x2A4B0000, // Address Base
0x00010000, // Address Length
)
Interrupt (ResourceConsumer, Level, ActiveHigh, Exclusive, ,, )
{
0x00000159,
}
})
...
}
The expression SMB0 is used to indicate SMBus HC#0,
a string of up to four characters.
Created the SMB0 object according to the following
specifications:
ACPI Specification
13.2. Accessing the SMBus from ASL Code
https://uefi.org/htmlspecs/ACPI_Spec_6_4_html/13_ACPI_System_Mgmt_Bus_Interface_Spec/accessing-the-smbus-from-asl-code.html
IPMI Specification
Example 4: SSIF Interface(P574)
https://www.intel.co.jp/content/www/jp/ja/products/docs/servers/ipmi/ipmi-second-gen-interface-spec-v2-rev1-1.html
Signed-off-by: Yoshihiro Furudera <fj5100bi@fujitsu.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
There's no reason for this driver to use OF-specific property helpers.
Drop the last one in favor of the generic variant and no longer include
of.h.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
phydev->eee_cfg.eee_enabled
This is a follow-up to 41ffcd95015f ("net: phy: fix phylib's dual
eee_enabled") and resolves an issue with genphy_c45_an_config_eee_aneg()
(called from genphy_c45_ethtool_set_eee) not seeing the new value of
phydev->eee_cfg.eee_enabled.
Fixes: 49168d1980e2 ("net: phy: Add phy_support_eee() indicating MAC support EEE")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull kvm updates from Paolo Bonzini:
"The biggest change here is eliminating the awful idea that KVM had of
essentially guessing which pfns are refcounted pages.
The reason to do so was that KVM needs to map both non-refcounted
pages (for example BARs of VFIO devices) and VM_PFNMAP/VM_MIXMEDMAP
VMAs that contain refcounted pages.
However, the result was security issues in the past, and more recently
the inability to map VM_IO and VM_PFNMAP memory that _is_ backed by
struct page but is not refcounted. In particular this broke virtio-gpu
blob resources (which directly map host graphics buffers into the
guest as "vram" for the virtio-gpu device) with the amdgpu driver,
because amdgpu allocates non-compound higher order pages and the tail
pages could not be mapped into KVM.
This requires adjusting all uses of struct page in the
per-architecture code, to always work on the pfn whenever possible.
The large series that did this, from David Stevens and Sean
Christopherson, also cleaned up substantially the set of functions
that provided arch code with the pfn for a host virtual addresses.
The previous maze of twisty little passages, all different, is
replaced by five functions (__gfn_to_page, __kvm_faultin_pfn, the
non-__ versions of these two, and kvm_prefetch_pages) saving almost
200 lines of code.
ARM:
- Support for stage-1 permission indirection (FEAT_S1PIE) and
permission overlays (FEAT_S1POE), including nested virt + the
emulated page table walker
- Introduce PSCI SYSTEM_OFF2 support to KVM + client driver. This
call was introduced in PSCIv1.3 as a mechanism to request
hibernation, similar to the S4 state in ACPI
- Explicitly trap + hide FEAT_MPAM (QoS controls) from KVM guests. As
part of it, introduce trivial initialization of the host's MPAM
context so KVM can use the corresponding traps
- PMU support under nested virtualization, honoring the guest
hypervisor's trap configuration and event filtering when running a
nested guest
- Fixes to vgic ITS serialization where stale device/interrupt table
entries are not zeroed when the mapping is invalidated by the VM
- Avoid emulated MMIO completion if userspace has requested
synchronous external abort injection
- Various fixes and cleanups affecting pKVM, vCPU initialization, and
selftests
LoongArch:
- Add iocsr and mmio bus simulation in kernel.
- Add in-kernel interrupt controller emulation.
- Add support for virtualization extensions to the eiointc irqchip.
PPC:
- Drop lingering and utterly obsolete references to PPC970 KVM, which
was removed 10 years ago.
- Fix incorrect documentation references to non-existing ioctls
RISC-V:
- Accelerate KVM RISC-V when running as a guest
- Perf support to collect KVM guest statistics from host side
s390:
- New selftests: more ucontrol selftests and CPU model sanity checks
- Support for the gen17 CPU model
- List registers supported by KVM_GET/SET_ONE_REG in the
documentation
x86:
- Cleanup KVM's handling of Accessed and Dirty bits to dedup code,
improve documentation, harden against unexpected changes.
Even if the hardware A/D tracking is disabled, it is possible to
use the hardware-defined A/D bits to track if a PFN is Accessed
and/or Dirty, and that removes a lot of special cases.
- Elide TLB flushes when aging secondary PTEs, as has been done in
x86's primary MMU for over 10 years.
- Recover huge pages in-place in the TDP MMU when dirty page logging
is toggled off, instead of zapping them and waiting until the page
is re-accessed to create a huge mapping. This reduces vCPU jitter.
- Batch TLB flushes when dirty page logging is toggled off. This
reduces the time it takes to disable dirty logging by ~3x.
- Remove the shrinker that was (poorly) attempting to reclaim shadow
page tables in low-memory situations.
- Clean up and optimize KVM's handling of writes to
MSR_IA32_APICBASE.
- Advertise CPUIDs for new instructions in Clearwater Forest
- Quirk KVM's misguided behavior of initialized certain feature MSRs
to their maximum supported feature set, which can result in KVM
creating invalid vCPU state. E.g. initializing PERF_CAPABILITIES to
a non-zero value results in the vCPU having invalid state if
userspace hides PDCM from the guest, which in turn can lead to
save/restore failures.
- Fix KVM's handling of non-canonical checks for vCPUs that support
LA57 to better follow the "architecture", in quotes because the
actual behavior is poorly documented. E.g. most MSR writes and
descriptor table loads ignore CR4.LA57 and operate purely on
whether the CPU supports LA57.
- Bypass the register cache when querying CPL from kvm_sched_out(),
as filling the cache from IRQ context is generally unsafe; harden
the cache accessors to try to prevent similar issues from occuring
in the future. The issue that triggered this change was already
fixed in 6.12, but was still kinda latent.
- Advertise AMD_IBPB_RET to userspace, and fix a related bug where
KVM over-advertises SPEC_CTRL when trying to support cross-vendor
VMs.
- Minor cleanups
- Switch hugepage recovery thread to use vhost_task.
These kthreads can consume significant amounts of CPU time on
behalf of a VM or in response to how the VM behaves (for example
how it accesses its memory); therefore KVM tried to place the
thread in the VM's cgroups and charge the CPU time consumed by that
work to the VM's container.
However the kthreads did not process SIGSTOP/SIGCONT, and therefore
cgroups which had KVM instances inside could not complete freezing.
Fix this by replacing the kthread with a PF_USER_WORKER thread, via
the vhost_task abstraction. Another 100+ lines removed, with
generally better behavior too like having these threads properly
parented in the process tree.
- Revert a workaround for an old CPU erratum (Nehalem/Westmere) that
didn't really work; there was really nothing to work around anyway:
the broken patch was meant to fix nested virtualization, but the
PERF_GLOBAL_CTRL MSR is virtualized and therefore unaffected by the
erratum.
- Fix 6.12 regression where CONFIG_KVM will be built as a module even
if asked to be builtin, as long as neither KVM_INTEL nor KVM_AMD is
'y'.
x86 selftests:
- x86 selftests can now use AVX.
Documentation:
- Use rST internal links
- Reorganize the introduction to the API document
Generic:
- Protect vcpu->pid accesses outside of vcpu->mutex with a rwlock
instead of RCU, so that running a vCPU on a different task doesn't
encounter long due to having to wait for all CPUs become quiescent.
In general both reads and writes are rare, but userspace that
supports confidential computing is introducing the use of "helper"
vCPUs that may jump from one host processor to another. Those will
be very happy to trigger a synchronize_rcu(), and the effect on
performance is quite the disaster"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (298 commits)
KVM: x86: Break CONFIG_KVM_X86's direct dependency on KVM_INTEL || KVM_AMD
KVM: x86: add back X86_LOCAL_APIC dependency
Revert "KVM: VMX: Move LOAD_IA32_PERF_GLOBAL_CTRL errata handling out of setup_vmcs_config()"
KVM: x86: switch hugepage recovery thread to vhost_task
KVM: x86: expose MSR_PLATFORM_INFO as a feature MSR
x86: KVM: Advertise CPUIDs for new instructions in Clearwater Forest
Documentation: KVM: fix malformed table
irqchip/loongson-eiointc: Add virt extension support
LoongArch: KVM: Add irqfd support
LoongArch: KVM: Add PCHPIC user mode read and write functions
LoongArch: KVM: Add PCHPIC read and write functions
LoongArch: KVM: Add PCHPIC device support
LoongArch: KVM: Add EIOINTC user mode read and write functions
LoongArch: KVM: Add EIOINTC read and write functions
LoongArch: KVM: Add EIOINTC device support
LoongArch: KVM: Add IPI user mode read and write function
LoongArch: KVM: Add IPI read and write function
LoongArch: KVM: Add IPI device support
LoongArch: KVM: Add iocsr and mmio bus simulation in kernel
KVM: arm64: Pass on SVE mapping failures
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Rework kfence support for the HPT MMU to work on systems with >= 16TB
of RAM.
- Remove the powerpc "maple" platform, used by the "Yellow Dog
Powerstation".
- Add support for DYNAMIC_FTRACE_WITH_CALL_OPS,
DYNAMIC_FTRACE_WITH_DIRECT_CALLS & BPF Trampolines.
- Add support for running KVM nested guests on Power11.
- Other small features, cleanups and fixes.
Thanks to Amit Machhiwal, Arnd Bergmann, Christophe Leroy, Costa
Shulyupin, David Hunter, David Wang, Disha Goel, Gautam Menghani, Geert
Uytterhoeven, Hari Bathini, Julia Lawall, Kajol Jain, Keith Packard,
Lukas Bulwahn, Madhavan Srinivasan, Markus Elfring, Michal Suchanek,
Ming Lei, Mukesh Kumar Chaurasiya, Nathan Chancellor, Naveen N Rao,
Nicholas Piggin, Nysal Jan K.A, Paulo Miguel Almeida, Pavithra Prakash,
Ritesh Harjani (IBM), Rob Herring (Arm), Sachin P Bappalige, Shen
Lichuan, Simon Horman, Sourabh Jain, Thomas Weißschuh, Thorsten Blum,
Thorsten Leemhuis, Venkat Rao Bagalkote, Zhang Zekun, and zhang jiao.
* tag 'powerpc-6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (89 commits)
EDAC/powerpc: Remove PPC_MAPLE drivers
powerpc/perf: Add per-task/process monitoring to vpa_pmu driver
powerpc/kvm: Add vpa latency counters to kvm_vcpu_arch
docs: ABI: sysfs-bus-event_source-devices-vpa-pmu: Document sysfs event format entries for vpa_pmu
powerpc/perf: Add perf interface to expose vpa counters
MAINTAINERS: powerpc: Mark Maddy as "M"
powerpc/Makefile: Allow overriding CPP
powerpc-km82xx.c: replace of_node_put() with __free
ps3: Correct some typos in comments
powerpc/kexec: Fix return of uninitialized variable
macintosh: Use common error handling code in via_pmu_led_init()
powerpc/powermac: Use of_property_match_string() in pmac_has_backlight_type()
powerpc: remove dead config options for MPC85xx platform support
powerpc/xive: Use cpumask_intersects()
selftests/powerpc: Remove the path after initialization.
powerpc/xmon: symbol lookup length fixed
powerpc/ep8248e: Use %pa to format resource_size_t
powerpc/ps3: Reorganize kerneldoc parameter names
KVM: PPC: Book3S HV: Fix kmv -> kvm typo
powerpc/sstep: make emulate_vsx_load and emulate_vsx_store static
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- The series "zram: optimal post-processing target selection" from
Sergey Senozhatsky improves zram's post-processing selection
algorithm. This leads to improved memory savings.
- Wei Yang has gone to town on the mapletree code, contributing several
series which clean up the implementation:
- "refine mas_mab_cp()"
- "Reduce the space to be cleared for maple_big_node"
- "maple_tree: simplify mas_push_node()"
- "Following cleanup after introduce mas_wr_store_type()"
- "refine storing null"
- The series "selftests/mm: hugetlb_fault_after_madv improvements" from
David Hildenbrand fixes this selftest for s390.
- The series "introduce pte_offset_map_{ro|rw}_nolock()" from Qi Zheng
implements some rationaizations and cleanups in the page mapping
code.
- The series "mm: optimize shadow entries removal" from Shakeel Butt
optimizes the file truncation code by speeding up the handling of
shadow entries.
- The series "Remove PageKsm()" from Matthew Wilcox completes the
migration of this flag over to being a folio-based flag.
- The series "Unify hugetlb into arch_get_unmapped_area functions" from
Oscar Salvador implements a bunch of consolidations and cleanups in
the hugetlb code.
- The series "Do not shatter hugezeropage on wp-fault" from Dev Jain
takes away the wp-fault time practice of turning a huge zero page
into small pages. Instead we replace the whole thing with a THP. More
consistent cleaner and potentiall saves a large number of pagefaults.
- The series "percpu: Add a test case and fix for clang" from Andy
Shevchenko enhances and fixes the kernel's built in percpu test code.
- The series "mm/mremap: Remove extra vma tree walk" from Liam Howlett
optimizes mremap() by avoiding doing things which we didn't need to
do.
- The series "Improve the tmpfs large folio read performance" from
Baolin Wang teaches tmpfs to copy data into userspace at the folio
size rather than as individual pages. A 20% speedup was observed.
- The series "mm/damon/vaddr: Fix issue in
damon_va_evenly_split_region()" fro Zheng Yejian fixes DAMON
splitting.
- The series "memcg-v1: fully deprecate charge moving" from Shakeel
Butt removes the long-deprecated memcgv2 charge moving feature.
- The series "fix error handling in mmap_region() and refactor" from
Lorenzo Stoakes cleanup up some of the mmap() error handling and
addresses some potential performance issues.
- The series "x86/module: use large ROX pages for text allocations"
from Mike Rapoport teaches x86 to use large pages for
read-only-execute module text.
- The series "page allocation tag compression" from Suren Baghdasaryan
is followon maintenance work for the new page allocation profiling
feature.
- The series "page->index removals in mm" from Matthew Wilcox remove
most references to page->index in mm/. A slow march towards shrinking
struct page.
- The series "damon/{self,kunit}tests: minor fixups for DAMON debugfs
interface tests" from Andrew Paniakin performs maintenance work for
DAMON's self testing code.
- The series "mm: zswap swap-out of large folios" from Kanchana Sridhar
improves zswap's batching of compression and decompression. It is a
step along the way towards using Intel IAA hardware acceleration for
this zswap operation.
- The series "kasan: migrate the last module test to kunit" from
Sabyrzhan Tasbolatov completes the migration of the KASAN built-in
tests over to the KUnit framework.
- The series "implement lightweight guard pages" from Lorenzo Stoakes
permits userapace to place fault-generating guard pages within a
single VMA, rather than requiring that multiple VMAs be created for
this. Improved efficiencies for userspace memory allocators are
expected.
- The series "memcg: tracepoint for flushing stats" from JP Kobryn uses
tracepoints to provide increased visibility into memcg stats flushing
activity.
- The series "zram: IDLE flag handling fixes" from Sergey Senozhatsky
fixes a zram buglet which potentially affected performance.
- The series "mm: add more kernel parameters to control mTHP" from
Maíra Canal enhances our ability to control/configuremultisize THP
from the kernel boot command line.
- The series "kasan: few improvements on kunit tests" from Sabyrzhan
Tasbolatov has a couple of fixups for the KASAN KUnit tests.
- The series "mm/list_lru: Split list_lru lock into per-cgroup scope"
from Kairui Song optimizes list_lru memory utilization when lockdep
is enabled.
* tag 'mm-stable-2024-11-18-19-27' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (215 commits)
cma: enforce non-zero pageblock_order during cma_init_reserved_mem()
mm/kfence: add a new kunit test test_use_after_free_read_nofault()
zram: fix NULL pointer in comp_algorithm_show()
memcg/hugetlb: add hugeTLB counters to memcg
vmstat: call fold_vm_zone_numa_events() before show per zone NUMA event
mm: mmap_lock: check trace_mmap_lock_$type_enabled() instead of regcount
zram: ZRAM_DEF_COMP should depend on ZRAM
MAINTAINERS/MEMORY MANAGEMENT: add document files for mm
Docs/mm/damon: recommend academic papers to read and/or cite
mm: define general function pXd_init()
kmemleak: iommu/iova: fix transient kmemleak false positive
mm/list_lru: simplify the list_lru walk callback function
mm/list_lru: split the lock to per-cgroup scope
mm/list_lru: simplify reparenting and initial allocation
mm/list_lru: code clean up for reparenting
mm/list_lru: don't export list_lru_add
mm/list_lru: don't pass unnecessary key parameters
kasan: add kunit tests for kmalloc_track_caller, kmalloc_node_track_caller
kasan: change kasan_atomics kunit test as KUNIT_CASE_SLOW
kasan: use EXPORT_SYMBOL_IF_KUNIT to export symbols
...
|
|
Negative temperatures are reported as large positive temperatures
due to missing sign extension from unsigned int to long. Cast unsigned
raw register values to signed before performing the calculations
to fix the problem.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: fff7b8ab2255 ("hwmon: add Texas Instruments TPS23861 driver")
Signed-off-by: Murad Masimov <m.masimov@maxima.ru>
Message-ID: <20241121173604.2021-1-m.masimov@maxima.ru>
[groeck: Updated subject and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
I3C device probe fails when CONFIG_REGMAP_I3C=m:
p3t1085_i3c 0-23615290090: error -ENODEV: Failed to register i3c regmap
Fix this by using the IS_ENABLED(CONFIG_REGMAP_I3C) macro in the code.
Fixes: c40655e33106 ("hwmon: (tmp108) Add support for I3C device")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Message-ID: <20241121121819.393104-1-jarkko.nikula@linux.intel.com>
[groeck: Remove #ifdef entirely; it is not needed due to dead code elimination]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull rdma updates from Jason Gunthorpe:
"Seveal fixes scattered across the drivers and a few new features:
- Minor updates and bug fixes to hfi1, efa, iopob, bnxt, hns
- Force disassociate the userspace FD when hns does an async reset
- bnxt new features for optimized modify QP to skip certain stayes,
CQ coalescing, better debug dumping
- mlx5 new data placement ordering feature
- Faster destruction of mlx5 devx HW objects
- Improvements to RDMA CM mad handling"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (51 commits)
RDMA/bnxt_re: Correct the sequence of device suspend
RDMA/bnxt_re: Use the default mode of congestion control
RDMA/bnxt_re: Support different traffic class
IB/cm: Rework sending DREQ when destroying a cm_id
IB/cm: Do not hold reference on cm_id unless needed
IB/cm: Explicitly mark if a response MAD is a retransmission
RDMA/mlx5: Move events notifier registration to be after device registration
RDMA/bnxt_re: Cache MSIx info to a local structure
RDMA/bnxt_re: Refurbish CQ to NQ hash calculation
RDMA/bnxt_re: Refactor NQ allocation
RDMA/bnxt_re: Fail probe early when not enough MSI-x vectors are reserved
RDMA/hns: Fix different dgids mapping to the same dip_idx
RDMA/bnxt_re: Add set_func_resources support for P5/P7 adapters
RDMA/bnxt_re: Enhance RoCE SRIOV resource configuration design
bnxt_en: Add support for RoCE sriov configuration
RDMA/hns: Fix NULL pointer derefernce in hns_roce_map_mr_sg()
RDMA/hns: Fix out-of-order issue of requester when setting FENCE
RDMA/nldev: Add IB device and net device rename events
RDMA/mlx5: Add implementation for ufile_hw_cleanup device operation
RDMA/core: Move ib_uverbs_file struct to uverbs_types.h
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu updates from Joerg Roedel:
"Core Updates:
- Convert call-sites using iommu_domain_alloc() to more specific
versions and remove function
- Introduce iommu_paging_domain_alloc_flags()
- Extend support for allocating PASID-capable domains to more drivers
- Remove iommu_present()
- Some smaller improvements
New IOMMU driver for RISC-V
Intel VT-d Updates:
- Add domain_alloc_paging support
- Enable user space IOPFs in non-PASID and non-svm cases
- Small code refactoring and cleanups
- Add domain replacement support for pasid
AMD-Vi Updates:
- Adapt to iommu_paging_domain_alloc_flags() interface and alloc V2
page-tables by default
- Replace custom domain ID allocator with IDA allocator
- Add ops->release_domain() support
- Other improvements to device attach and domain allocation code
paths
ARM-SMMU Updates:
- SMMUv2:
- Return -EPROBE_DEFER for client devices probing before their
SMMU
- Devicetree binding updates for Qualcomm MMU-500 implementations
- SMMUv3:
- Minor fixes and cleanup for NVIDIA's virtual command queue
driver
- IO-PGTable:
- Fix indexing of concatenated PGDs and extend selftest coverage
- Remove unused block-splitting support
S390 IOMMU:
- Implement support for blocking domain
Mediatek IOMMU:
- Enable 35-bit physical address support for mt8186
OMAP IOMMU driver:
- Adapt to recent IOMMU core changes and unbreak driver"
* tag 'iommu-updates-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (92 commits)
iommu/tegra241-cmdqv: Fix alignment failure at max_n_shift
iommu: Make set_dev_pasid op support domain replacement
iommu/arm-smmu-v3: Make set_dev_pasid() op support replace
iommu/vt-d: Add set_dev_pasid callback for nested domain
iommu/vt-d: Make identity_domain_set_dev_pasid() to handle domain replacement
iommu/vt-d: Make intel_svm_set_dev_pasid() support domain replacement
iommu/vt-d: Limit intel_iommu_set_dev_pasid() for paging domain
iommu/vt-d: Make intel_iommu_set_dev_pasid() to handle domain replacement
iommu/vt-d: Add iommu_domain_did() to get did
iommu/vt-d: Consolidate the struct dev_pasid_info add/remove
iommu/vt-d: Add pasid replace helpers
iommu/vt-d: Refactor the pasid setup helpers
iommu/vt-d: Add a helper to flush cache for updating present pasid entry
iommu: Pass old domain to set_dev_pasid op
iommu/iova: Fix typo 'adderss'
iommu: Add a kdoc to iommu_unmap()
iommu/io-pgtable-arm-v7s: Remove split on unmap behavior
iommu/io-pgtable-arm: Remove split on unmap behavior
iommu/vt-d: Drain PRQs when domain removed from RID
iommu/vt-d: Drop pasid requirement for prq initialization
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more thermal control updates from Rafael Wysocki:
"These update a few thermal drivers used on ARM platforms and thermal
tools:
- Add SAR2130P compatible to DT bindings in the QCom Tsens driver
(Dmitry Baryshkov)
- Add static annotation to arrays describing platform sensors in the
LVTS Mediatek driver (Colin Ian King)
- Switch back to struct platform_driver::remove() from the previous
callbacks prototype rework (Uwe Kleine-König)
- Add MSM8937 compatible to DT bindings and its support in the QCom
Tsens driver (Barnabás Czémán)
- Remove a pointless sign test on an unsigned value in
k3_bgp_read_temp() in the k3_j72xx_bandgap driver (Rex Nie)
- Fix a pointer reference loss when realloc() fails in the thermal
library (Zhang Jiao)"
* tag 'thermal-6.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tools/thermal: Fix common realloc mistake
thermal/drivers/k3_j72xx_bandgap: Simplify code in k3_bgp_read_temp()
thermal/drivers/qcom/tsens-v1: Add support for MSM8937 tsens
dt-bindings: thermal: tsens: Add MSM8937
thermal: Switch back to struct platform_driver::remove()
thermal/drivers/mediatek/lvts_thermal: Make read-only arrays static const
dt-bindings: thermal: qcom-tsens: Add SAR2130P compatible
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These mostly are updates of cpufreq drivers used on ARM platforms plus
one new DT-based cpufreq driver for virtualized guests and two cpuidle
changes that should not make any difference on systems currently in
the field, but will be needed for future development:
- Add virtual cpufreq driver for guest kernels (David Dai)
- Minor cleanup to various cpufreq drivers (Andy Shevchenko, Dhruva
Gole, Jie Zhan, Jinjie Ruan, Shuosheng Huang, Sibi Sankar, and Yuan
Can)
- Revert "cpufreq: brcmstb-avs-cpufreq: Fix initial command check"
(Colin Ian King)
- Improve DT bindings for qcom-hw driver (Dmitry Baryshkov, Konrad
Dybcio, and Nikunj Kela)
- Make cpuidle_play_dead() try all idle states with :enter_dead()
callbacks and change their return type to void (Rafael Wysocki)"
* tag 'pm-6.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (22 commits)
cpuidle: Change :enter_dead() driver callback return type to void
cpuidle: Do not return from cpuidle_play_dead() on callback failures
arm64: dts: qcom: sc8180x: Add a SoC-specific compatible to cpufreq-hw
dt-bindings: cpufreq: cpufreq-qcom-hw: Add SC8180X compatible
cpufreq: sun50i: add a100 cpufreq support
cpufreq: mediatek-hw: Fix wrong return value in mtk_cpufreq_get_cpu_power()
cpufreq: CPPC: Fix wrong return value in cppc_get_cpu_power()
cpufreq: CPPC: Fix wrong return value in cppc_get_cpu_cost()
cpufreq: loongson3: Check for error code from devm_mutex_init() call
cpufreq: scmi: Fix cleanup path when boost enablement fails
cpufreq: CPPC: Fix possible null-ptr-deref for cppc_get_cpu_cost()
cpufreq: CPPC: Fix possible null-ptr-deref for cpufreq_cpu_get_raw()
Revert "cpufreq: brcmstb-avs-cpufreq: Fix initial command check"
dt-bindings: cpufreq: cpufreq-qcom-hw: Add SAR2130P compatible
cpufreq: add virtual-cpufreq driver
dt-bindings: cpufreq: add virtual cpufreq device
cpufreq: loongson2: Unregister platform_driver on failure
cpufreq: ti-cpufreq: Remove revision offsets in AM62 family
cpufreq: ti-cpufreq: Allow backward compatibility for efuse syscon
cppc_cpufreq: Remove HiSilicon CPPC workaround
...
|
