| Age | Commit message (Collapse) | Author |
|---|
|
commit 83997997252f5d3fc7f04abc24a89600c2b504ab upstream.
RX overflow interrupt (RXOFLW) is disabled even though xcan_interrupt()
processes it. This means that an RX overflow interrupt will only be
processed when another interrupt gets asserted (e.g. for RX/TX).
Fix that by enabling the RXOFLW interrupt.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 620050d9c2be15c47017ba95efe59e0832e99a56 upstream.
The xilinx_can driver assumes that the TXOK interrupt only clears after
it has been acknowledged as many times as there have been successfully
sent frames.
However, the documentation does not mention such behavior, instead
saying just that the interrupt is cleared when the clear bit is set.
Similarly, testing seems to also suggest that it is immediately cleared
regardless of the amount of frames having been sent. Performing some
heavy TX load and then going back to idle has the tx_head drifting
further away from tx_tail over time, steadily reducing the amount of
frames the driver keeps in the TX FIFO (but not to zero, as the TXOK
interrupt always frees up space for 1 frame from the driver's
perspective, so frames continue to be sent) and delaying the local echo
frames.
The TX FIFO tracking is also otherwise buggy as it does not account for
TX FIFO being cleared after software resets, causing
BUG!, TX FIFO full when queue awake!
messages to be output.
There does not seem to be any way to accurately track the state of the
TX FIFO for local echo support while using the full TX FIFO.
The Zynq version of the HW (but not the soft-AXI version) has watermark
programming support and with it an additional TX-FIFO-empty interrupt
bit.
Modify the driver to only put 1 frame into TX FIFO at a time on soft-AXI
and 2 frames at a time on Zynq. On Zynq the TXFEMP interrupt bit is used
to detect whether 1 or 2 frames have been sent at interrupt processing
time.
Tested with the integrated CAN on Zynq-7000 SoC. The 1-frame-FIFO mode
was also tested.
An alternative way to solve this would be to drop local echo support but
keep using the full TX FIFO.
v2: Add FIFO space check before TX queue wake with locking to
synchronize with queue stop. This avoids waking the queue when xmit()
had just filled it.
v3: Keep local echo support and reduce the amount of frames in FIFO
instead as suggested by Marc Kleine-Budde.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2574fe54515ed3487405de329e4e9f13d7098c10 upstream.
The xilinx_can driver performs a software reset when an RX overrun is
detected. This causes the device to enter Configuration mode where no
messages are received or transmitted.
The documentation does not mention any need to perform a reset on an RX
overrun, and testing by inducing an RX overflow also indicated that the
device continues to work just fine without a reset.
Remove the software reset.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 32852c561bffd613d4ed7ec464b1e03e1b7b6c5c upstream.
If the device gets into a state where RXNEMP (RX FIFO not empty)
interrupt is asserted without RXOK (new frame received successfully)
interrupt being asserted, xcan_rx_poll() will continue to try to clear
RXNEMP without actually reading frames from RX FIFO. If the RX FIFO is
not empty, the interrupt will not be cleared and napi_schedule() will
just be called again.
This situation can occur when:
(a) xcan_rx() returns without reading RX FIFO due to an error condition.
The code tries to clear both RXOK and RXNEMP but RXNEMP will not clear
due to a frame still being in the FIFO. The frame will never be read
from the FIFO as RXOK is no longer set.
(b) A frame is received between xcan_rx_poll() reading interrupt status
and clearing RXOK. RXOK will be cleared, but RXNEMP will again remain
set as the new message is still in the FIFO.
I'm able to trigger case (b) by flooding the bus with frames under load.
There does not seem to be any benefit in using both RXNEMP and RXOK in
the way the driver does, and the polling example in the reference manual
(UG585 v1.10 18.3.7 Read Messages from RxFIFO) also says that either
RXOK or RXNEMP can be used for detecting incoming messages.
Fix the issue and simplify the RX processing by only using RXNEMP
without RXOK.
Tested with the integrated CAN on Zynq-7000 SoC.
Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d644abf25698362bd33d17c9ddc8f7122c30f17 upstream.
Commit 1b9ba000 ("Allow function drivers to pause control
transfers") states that USB_GADGET_DELAYED_STATUS is only
supported if data phase is 0 bytes.
It seems that when the length is not 0 bytes, there is no
need to explicitly delay the data stage since the transfer
is not completed until the user responds. However, when the
length is 0, there is no data stage and the transfer is
finished once setup() returns, hence there is a need to
explicitly delay completion.
This manifests as the following bugs:
Prior to 946ef68ad4e4 ('Let setup() return
USB_GADGET_DELAYED_STATUS'), when setup is 0 bytes, ffs
would require user to queue a 0 byte request in order to
clear setup state. However, that 0 byte request was actually
not needed and would hang and cause errors in other setup
requests.
After the above commit, 0 byte setups work since the gadget
now accepts empty queues to ep0 to clear the delay, but all
other setups hang.
Fixes: 946ef68ad4e4 ("Let setup() return USB_GADGET_DELAYED_STATUS")
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 249a32b7eeb3edb6897dd38f89651a62163ac4ed upstream.
Based on USB2.0 Spec Section 11.12.5,
"If a hub has per-port power switching and per-port current limiting,
an over-current on one port may still cause the power on another port
to fall below specific minimums. In this case, the affected port is
placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the
port, but PORT_OVER_CURRENT is not set."
so let's check C_PORT_OVER_CURRENT too for over current condition.
Fixes: 08d1dec6f405 ("usb:hub set hub->change_bits when over-current happens")
Cc: <stable@vger.kernel.org>
Tested-by: Alessandro Antenucci <antenucci@korg.it>
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1445cbe476fc3dd09c0b380b206526a49403c071 upstream.
The device (a POS terminal) implements CDC ACM, but has not union
descriptor.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 958c696f5a7274d9447a458ad7aa70719b29a50a ]
Function mlx4_RST2INIT_QP_wrapper saved the qp number passed in the qp
context, rather than the one passed in the input modifier.
However, the qp number in the qp context is not defined as a
required parameter by the FW. Therefore, drivers may choose to not
specify the qp number in the qp context for the reset-to-init transition.
Thus, we must save the qp number passed in the command input modifier --
which is always present. (This saved qp number is used as the input
modifier for command 2RST_QP when a slave's qp's are destroyed).
Fixes: c82e9aa0a8bc ("mlx4_core: resource tracking for HCA resources used by guests")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9ba8376ce1e2cbf4ce44f7e4bee1d0648e10d594 ]
It seems that a *break* is missing in order to avoid falling through
to the default case. Otherwise, checking *chan* makes no sense.
Fixes: 72df7a7244c0 ("ptp: Allow reassigning calibration pin function")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d412c31dae053bf30a1bc15582a9990df297a660 ]
The command interface can work in two modes: Events and Polling.
In the general case, each time we invoke a command, a work is
queued to handle it.
When working in events, the interrupt handler completes the
command execution. On the other hand, when working in polling
mode, the work itself completes it.
Due to a bug in the work handler, a command could have been
completed by the interrupt handler, while the work handler
hasn't finished yet, causing the it to complete once again
if the command interface mode was changed from Events to
polling after the interrupt handler was called.
mlx5_unload_one()
mlx5_stop_eqs()
// Destroy the EQ before cmd EQ
...cmd_work_handler()
write_doorbell()
--> EVENT_TYPE_CMD
mlx5_cmd_comp_handler() // First free
free_ent(cmd, ent->idx)
complete(&ent->done)
<-- mlx5_stop_eqs //cmd was complete
// move to polling before destroying the last cmd EQ
mlx5_cmd_use_polling()
cmd->mode = POLL;
--> cmd_work_handler (continues)
if (cmd->mode == POLL)
mlx5_cmd_comp_handler() // Double free
The solution is to store the cmd->mode before writing the doorbell.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b8f1f65882f07913157c44673af7ec0b308d03eb ]
Sock will be NULL if we pass -1 to vhost_net_set_backend(), but when
we meet errors during ubuf allocation, the code does not check for
NULL before calling sockfd_put(), this will lead NULL
dereferencing. Fixing by checking sock pointer before.
Fixes: bab632d69ee4 ("vhost: vhost TX zero-copy support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 12b03558cef6d655d0d394f5e98a6fd07c1f6c0f ]
After commit 88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE
are friends"), sungem owners reported the infamous "eth0: hw csum failure"
message.
CHECKSUM_COMPLETE has in fact never worked for this driver, but this
was masked by the fact that upper stacks had to strip the FCS, and
therefore skb->ip_summed was set back to CHECKSUM_NONE before
my recent change.
Driver configures a number of bytes to skip when the chip computes
the checksum, and for some reason only half of the Ethernet header
was skipped.
Then a second problem is that we should strip the FCS by default,
unless the driver is updated to eventually support NETIF_F_RXFCS in
the future.
Finally, a driver should check if NETIF_F_RXCSUM feature is enabled
or not, so that the admin can turn off rx checksum if wanted.
Many thanks to Andreas Schwab and Mathieu Malaterre for their
help in debugging this issue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Mathieu Malaterre <malat@debian.org>
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Tested-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 603b7bcff824740500ddfa001d7a7168b0b38542 ]
The NULL character was not set correctly for the string containing
the command length, this caused failures reading the output of the
command due to a random length. The fix is to initialize the output
length string.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d59ad6eea82ef8df92b4109615a0dde9d8093e9 upstream.
If one of the later memory allocations in rypto4xx_build_pdr()
fails: dev->pdr (and/or) dev->pdr_uinfo wouldn't be freed.
crypto4xx_build_sdr() has the same issue with dev->sdr.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a728a196d253530f17da5c86dc7dfbe58c5f7094 upstream.
alg entries are only added to the list, after the registration
was successful. If the registration failed, it was never added
to the list in the first place.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d6213c1f2ad54a964b77471690264ed685718928 upstream.
The DMA controller regs actually point to DMA channel 0, so the write to
ENETDMA_CFG_REG will actually modify a random DMA channel.
Since DMA controller registers do not exist on BCM6345, guard the write
with the usual check for dma_has_sram.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9c86b846ce02f7e35d7234cf090b80553eba5389 upstream.
Check the return code of prepare_enable and change one last instance of
enable only to prepare_enable. Also properly disable and release the
clock in error paths and on remove for enetsw.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3349b6b3c373ac1fbfb040b810fcee5e2adc7e0 upstream.
syzbot is hitting WARN() triggered by memory allocation fault
injection [1] because loop module is calling sysfs_remove_group()
when sysfs_create_group() failed.
Fix this by remembering whether sysfs_create_group() succeeded.
[1] https://syzkaller.appspot.com/bug?id=3f86c0edf75c86d2633aeb9dd69eccc70bc7e90b
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+9f03168400f56df89dbc6f1751f4458fe739ff29@syzkaller.appspotmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renamed sysfs_ready -> sysfs_inited.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a8690ed6f5346f6738971892205e91d39b6b901 upstream.
In commit 357d23c811a7 ("Remove the obsolete libibcm library")
in rdma-core [1], we removed obsolete library which used the
/dev/infiniband/ucmX interface.
Following multiple syzkaller reports about non-sanitized
user input in the UCMA module, the short audit reveals the same
issues in UCM module too.
It is better to disable this interface in the kernel,
before syzkaller team invests time and energy to harden
this unused interface.
[1] https://github.com/linux-rdma/rdma-core/pull/279
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2ac838e4cd7e5e9891ecc094d626734b0245c99 upstream.
Refactor the validation code used in LOOP_SET_FD so it is also used in
LOOP_CHANGE_FD. Otherwise it is possible to construct a set of loop
devices that all refer to each other. This can lead to a infinite
loop in starting with "while (is_loop_device(f)) .." in loop_set_fd().
Fix this by refactoring out the validation code and using it for
LOOP_CHANGE_FD as well as LOOP_SET_FD.
Reported-by: syzbot+4349872271ece473a7c91190b68b4bac7c5dbc87@syzkaller.appspotmail.com
Reported-by: syzbot+40bd32c4d9a3cc12a339@syzkaller.appspotmail.com
Reported-by: syzbot+769c54e66f994b041be7@syzkaller.appspotmail.com
Reported-by: syzbot+0a89a9ce473936c57065@syzkaller.appspotmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 313db3d6488bb03b61b99de9dbca061f1fd838e1 upstream.
The > should be >= here so that we don't read one element beyond the end
of the ep->stream_info->stream_rings[] array.
Fixes: e9df17eb1408 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bba57eddadda936c94b5dccf73787cb9e159d0a5 upstream.
Corsair Strafe appears to suffer from the same issues
as the Corsair Strafe RGB.
Apply the same quirks (control message delay and init delay)
that the RGB version has to 1b1c:1b15.
With these quirks in place the keyboard works correctly upon
booting the system, and no longer requires reattaching the device.
Signed-off-by: Nico Sneck <snecknico@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 794744abfffef8b1f3c0c8a4896177d6d13d653d upstream.
Add missing transfer-length sanity check to the status-register
completion handler to avoid leaking bits of uninitialised slab data to
user space.
Fixes: 3f5429746d91 ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1e255d60ae66a9f672ff9a207ee6cd8e33d2679 upstream.
In general, accessing userspace memory beyond the length of the supplied
buffer in VFS read/write handlers can lead to both kernel memory corruption
(via kernel_read()/kernel_write(), which can e.g. be triggered via
sys_splice()) and privilege escalation inside userspace.
Fix it by using simple_read_from_buffer() instead of custom logic.
Fixes: 6bc235a2e24a ("USB: add driver for Meywa-Denki & Kayac YUREX")
Signed-off-by: Jann Horn <jannh@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 01b3cdfca263a17554f7b249d20a247b2a751521 upstream.
Fix broken modem-status error handling which could lead to bits of slab
data leaking to user space.
Fixes: 3b36a8fd6777 ("usb: fix uninitialized variable warning in keyspan_pda")
Cc: stable <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0341fc1981a950c1e902ab901e98f60e0e243f3 upstream.
This read handler had a lot of custom logic and wrote outside the bounds of
the provided buffer. This could lead to kernel and userspace memory
corruption. Just use simple_read_from_buffer() with a stack buffer.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 79ca484b613041ca223f74b34608bb6f5221724b upstream.
Currently the functions use to check both chip ready and good.
But the chip ready is not enough to check the operation status.
So change this to check the chip good instead of this.
About the retry functions to make sure the error handling remain it.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 45f75b8a919a4255f52df454f1ffdee0e42443b2 upstream.
For the word write functions it is retried for error.
But it is not implemented to retry for the erase functions.
To make sure for the erase functions change to retry as same.
This is needed to prevent the flash erase error caused only once.
It was caused by the error case of chip_good() in the do_erase_oneblock().
Also it was confirmed on the MACRONIX flash device MX29GL512FHT2I-11G.
But the error issue behavior is not able to reproduce at this moment.
The flash controller is parallel Flash interface integrated on BCM53003.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 85a82e28b023de9b259a86824afbd6ba07bd6475 upstream.
The definition can be used for other program and erase operations also.
So change the naming to MAX_RETRIES from MAX_WORD_RETRIES.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3f77f244d8ec28e3a0a81240ffac7d626390060c upstream.
The v21 version of the NAND flash controller contains a Spare Area Size
Register (SPAS) at offset 0x10. Its setting defaults to the maximum
spare area size of 218 bytes. The size that is set in this register is
used by the controller when it calculates the ECC bytes internally in
hardware.
Usually, this register is updated from settings in the IIM fuses when
the system is booting from NAND flash. For other boot media, however,
the SPAS register remains at the default setting, which may not work for
the particular flash chip on the board. The same goes for flash chips
whose configuration cannot be set in the IIM fuses (e.g. chips with 2k
sector size and 128 bytes spare area size can't be configured in the IIM
fuses on imx25 systems).
Set the SPAS register explicitly during the preset operation. Derive the
register value from mtd->oobsize that was detected during probe by
decoding the flash chip's ID bytes.
While at it, rename the define for the spare area register's offset to
NFC_V21_RSLTSPARE_AREA. The register at offset 0x10 on v1 controllers is
different from the register on v21 controllers.
Fixes: d484018 ("mtd: mxc_nand: set NFC registers after reset")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41c73a49df31151f4ff868f28fe4f129f113fa2c upstream.
If the first allocation attempt using GFP_NOWAIT fails, drop the lock
and retry using GFP_NOIO allocation (lock is dropped because the
allocation can take some time).
Note that we won't do GFP_NOIO allocation when we loop for the second
time, because the lock shouldn't be dropped between __wait_for_free_buffer
and __get_unclaimed_buffer.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ea61cac0b1ad0c09022f39fd97e9b99a2cfc2dc upstream.
We've seen in-field reports showing _lots_ (18 in one case, 41 in
another) of tasks all sitting there blocked on:
mutex_lock+0x4c/0x68
dm_bufio_shrink_count+0x38/0x78
shrink_slab.part.54.constprop.65+0x100/0x464
shrink_zone+0xa8/0x198
In the two cases analyzed, we see one task that looks like this:
Workqueue: kverityd verity_prefetch_io
__switch_to+0x9c/0xa8
__schedule+0x440/0x6d8
schedule+0x94/0xb4
schedule_timeout+0x204/0x27c
schedule_timeout_uninterruptible+0x44/0x50
wait_iff_congested+0x9c/0x1f0
shrink_inactive_list+0x3a0/0x4cc
shrink_lruvec+0x418/0x5cc
shrink_zone+0x88/0x198
try_to_free_pages+0x51c/0x588
__alloc_pages_nodemask+0x648/0xa88
__get_free_pages+0x34/0x7c
alloc_buffer+0xa4/0x144
__bufio_new+0x84/0x278
dm_bufio_prefetch+0x9c/0x154
verity_prefetch_io+0xe8/0x10c
process_one_work+0x240/0x424
worker_thread+0x2fc/0x424
kthread+0x10c/0x114
...and that looks to be the one holding the mutex.
The problem has been reproduced on fairly easily:
0. Be running Chrome OS w/ verity enabled on the root filesystem
1. Pick test patch: http://crosreview.com/412360
2. Install launchBalloons.sh and balloon.arm from
http://crbug.com/468342
...that's just a memory stress test app.
3. On a 4GB rk3399 machine, run
nice ./launchBalloons.sh 4 900 100000
...that tries to eat 4 * 900 MB of memory and keep accessing.
4. Login to the Chrome web browser and restore many tabs
With that, I've seen printouts like:
DOUG: long bufio 90758 ms
...and stack trace always show's we're in dm_bufio_prefetch().
The problem is that we try to allocate memory with GFP_NOIO while
we're holding the dm_bufio lock. Instead we should be using
GFP_NOWAIT. Using GFP_NOIO can cause us to sleep while holding the
lock and that causes the above problems.
The current behavior explained by David Rientjes:
It will still try reclaim initially because __GFP_WAIT (or
__GFP_KSWAPD_RECLAIM) is set by GFP_NOIO. This is the cause of
contention on dm_bufio_lock() that the thread holds. You want to
pass GFP_NOWAIT instead of GFP_NOIO to alloc_buffer() when holding a
mutex that can be contended by a concurrent slab shrinker (if
count_objects didn't use a trylock, this pattern would trivially
deadlock).
This change significantly increases responsiveness of the system while
in this state. It makes a real difference because it unblocks kswapd.
In the bug report analyzed, kswapd was hung:
kswapd0 D ffffffc000204fd8 0 72 2 0x00000000
Call trace:
[<ffffffc000204fd8>] __switch_to+0x9c/0xa8
[<ffffffc00090b794>] __schedule+0x440/0x6d8
[<ffffffc00090bac0>] schedule+0x94/0xb4
[<ffffffc00090be44>] schedule_preempt_disabled+0x28/0x44
[<ffffffc00090d900>] __mutex_lock_slowpath+0x120/0x1ac
[<ffffffc00090d9d8>] mutex_lock+0x4c/0x68
[<ffffffc000708e7c>] dm_bufio_shrink_count+0x38/0x78
[<ffffffc00030b268>] shrink_slab.part.54.constprop.65+0x100/0x464
[<ffffffc00030dbd8>] shrink_zone+0xa8/0x198
[<ffffffc00030e578>] balance_pgdat+0x328/0x508
[<ffffffc00030eb7c>] kswapd+0x424/0x51c
[<ffffffc00023f06c>] kthread+0x10c/0x114
[<ffffffc000203dd0>] ret_from_fork+0x10/0x40
By unblocking kswapd memory pressure should be reduced.
Suggested-by: David Rientjes <rientjes@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3ee9bc12342cf546313d300808ff47d7dbb8e7db upstream.
The cx25840 driver currently configures 885, 887, and 888 using
default divisors for each chip. This check to see if the cx23885
driver has passed the cx25840 a non-default clock rate for a
specific chip. If a cx23885 board has left clk_freq at 0, the
clock default values will be used to configure the PLLs.
This patch only has effect on 888 boards who set clk_freq to 25M.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 717adfdaf14704fd3ec7fa2c04520c0723247eac upstream.
If our length is greater than the size of the buffer, we
overflow the buffer
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Rosenberg <drosen@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef6eaf27274c0351f7059163918f3795da13199c upstream.
Commit ac75a041048b ("HID: i2c-hid: fix size check and type usage") started
writing messages when the ret_size is <= 2 from i2c_master_recv. However, my
device i2c-DLL07D1 returns 2 for a short period of time (~0.5s) after I stop
moving the pointing stick or touchpad. It varies, but you get ~50 messages
each time which spams the log hard.
[ 95.925055] i2c_hid i2c-DLL07D1:01: i2c_hid_get_input: incomplete report (83/2)
This has also been observed with a i2c-ALP0017.
[ 1781.266353] i2c_hid i2c-ALP0017:00: i2c_hid_get_input: incomplete report (30/2)
Only print the message when ret_size is totally invalid and less than 2 to cut
down on the log spam.
Fixes: ac75a041048b ("HID: i2c-hid: fix size check and type usage")
Reported-by: John Smith <john-s-84@gmx.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26b5b874aff5659a7e26e5b1997e3df2c41fa7fd upstream.
As Al Viro noted in commit 128394eff343 ("sg_write()/bsg_write() is not fit
to be called under KERNEL_DS"), sg improperly accesses userspace memory
outside the provided buffer, permitting kernel memory corruption via
splice(). But it doesn't just do it on ->write(), also on ->read().
As a band-aid, make sure that the ->read() and ->write() handlers can not
be called in weird contexts (kernel context or credentials different from
file opener), like for ib_safe_file_access().
If someone needs to use these interfaces from different security contexts,
a new interface should be written that goes through the ->ioctl() handler.
I've mostly copypasted ib_safe_file_access() over as sg_safe_file_access()
because I couldn't find a good common header - please tell me if you know a
better way.
[mkp: s/_safe_/_check_/]
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 26de0b76d9ba3200f09c6cb9d9618bda338be5f7 ]
With CONFIG_DMA_API_DEBUG=y, calling sonic_open() produces the
message, "DMA-API: device driver failed to check map error".
Add the missing dma_mapping_error() call.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2415f3bd059fe050eb98aedf93664d000ceb4e92 ]
Add support for Netgear Aircard 779S
Signed-off-by: Josh Hill <josh@joshuajhill.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f9c6442a8f0b1dde9e755eb4ff6fa22bcce4eabc ]
memcmp() returns int, but eprom_try_esi() cast it to unsigned char. One
can lose significant bits and get 0 from non-0 value returned by the
memcmp().
Signed-off-by: Ivan Bornyakov <brnkv.i1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 781932375ffc6411713ee0926ccae8596ed0261c upstream.
Fastmap cannot track the LEB unmap operation, therefore it can
happen that after an interrupted erasure the mapping still looks
good from Fastmap's point of view, while reading from the PEB will
cause an ECC error and confuses the upper layer.
Instead of teaching users of UBI how to deal with that, we read back
the VID header and check for errors. If the PEB is empty or shows ECC
errors we fixup the mapping and schedule the PEB for erasure.
Fixes: dbb7d2a88d2a ("UBI: Add fastmap core")
Cc: <stable@vger.kernel.org>
Reported-by: martin bayern <Martinbayern@outlook.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a2bc00341dcfcc793c0dbf4f8d43adf60458b05 upstream.
The expected return value from ion_map_kernel is an ERR_PTR. The error
path for a vmalloc failure currently just returns NULL, triggering
a warning in ion_buffer_kmap_get. Encode the vmalloc failure as an ERR_PTR.
Reported-by: syzbot+55b1d9f811650de944c6@syzkaller.appspotmail.com
Signed-off-by: Laura Abbott <labbott@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d63b7e4ae0dc5e02d28ddd2fa1f945defc68d81 upstream.
syzbot is reporting stalls at n_tty_receive_char_special() [1]. This is
because comparison is not working as expected since ldata->read_head can
change at any moment. Mitigate this by explicitly masking with buffer size
when checking condition for "while" loops.
[1] https://syzkaller.appspot.com/bug?id=3d7481a346958d9469bebbeb0537d5f056bdd6e8
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+18df353d7540aa6b5467@syzkaller.appspotmail.com>
Fixes: bc5a5e3f45d04784 ("n_tty: Don't wrap input buffer indices at buffer size")
Cc: stable <stable@vger.kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a685557fbbc3122ed11e8ad3fa63a11ebc5de8c3 upstream.
Discards issued to a DM thin device can complete to userspace (via
fstrim) _before_ the metadata changes associated with the discards is
reflected in the thinp superblock (e.g. free blocks). As such, if a
user constructs a test that loops repeatedly over these steps, block
allocation can fail due to discards not having completed yet:
1) fill thin device via filesystem file
2) remove file
3) fstrim
From initial report, here:
https://www.redhat.com/archives/dm-devel/2018-April/msg00022.html
"The root cause of this issue is that dm-thin will first remove
mapping and increase corresponding blocks' reference count to prevent
them from being reused before DISCARD bios get processed by the
underlying layers. However. increasing blocks' reference count could
also increase the nr_allocated_this_transaction in struct sm_disk
which makes smd->old_ll.nr_allocated +
smd->nr_allocated_this_transaction bigger than smd->old_ll.nr_blocks.
In this case, alloc_data_block() will never commit metadata to reset
the begin pointer of struct sm_disk, because sm_disk_get_nr_free()
always return an underflow value."
While there is room for improvement to the space-map accounting that
thinp is making use of: the reality is this test is inherently racey and
will result in the previous iteration's fstrim's discard(s) completing
vs concurrent block allocation, via dd, in the next iteration of the
loop.
No amount of space map accounting improvements will be able to allow
user's to use a block before a discard of that block has completed.
So the best we can really do is allow DM thinp to gracefully handle such
aggressive use of all the pool's data by degrading the pool into
out-of-data-space (OODS) mode. We _should_ get that behaviour already
(if space map accounting didn't falsely cause alloc_data_block() to
believe free space was available).. but short of that we handle the
current reality that dm_pool_alloc_data_block() can return -ENOSPC.
Reported-by: Dennis Yang <dennisyang@qnap.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eef04c7b3786ff0c9cb1019278b6c6c2ea0ad4ff upstream.
Commit 910f8befdf5b ("xen/pirq: fix error path cleanup when binding
MSIs") fixed a couple of errors in error cleanup path of
xen_bind_pirq_msi_to_irq(). This cleanup allowed a call to
__unbind_from_irq() with an unbound irq, which would result in
triggering the BUG_ON there.
Since there is really no reason for the BUG_ON (xen_free_irq() can
operate on unbound irqs) we can remove it.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f645bcc566a1e9f921bdae7528a01ced5bc3713 upstream.
cmap->len can get close to INT_MAX/2, allowing for an integer overflow in
allocation. This uses kmalloc_array() instead to catch the condition.
Reported-by: Dr Silvio Cesare of InfoSect <silvio.cesare@gmail.com>
Fixes: 8bdb3a2d7df48 ("uvesafb: the driver core")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 76d81243a487c09619822ef8e7201a756e58a87d upstream.
As warned by smatch:
drivers/media/dvb-core/dvb_frontend.c:314 dvb_frontend_get_event() warn: inconsistent returns 'sem:&fepriv->sem'.
Locked on: line 288
line 295
line 306
line 314
Unlocked on: line 303
The lock implementation for get event is wrong, as, if an
interrupt occurs, down_interruptible() will fail, and the
routine will call up() twice when userspace calls the ioctl
again.
The bad code is there since when Linux migrated to git, in
2005.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29e61d6ef061b012d320327af7dbb3990e75be45 upstream.
User reports AverMedia DVD EZMaker 7 can be driven by VIDEO_GRABBER.
Add the device to the id_table to make it work.
BugLink: https://bugs.launchpad.net/bugs/1620762
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea72fbf588ac9c017224dcdaa2019ff52ca56fee upstream.
As warned by smatch:
drivers/media/v4l2-core/v4l2-compat-ioctl32.c:879 put_v4l2_ext_controls32() warn: check for integer overflow 'count'
The access_ok() logic should check for too big arrays too.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2b12dfa124dbadf391cb9a616aaa6b056823bf75 upstream.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
This would only cause trouble if the child node is missing while there
is an unrelated node named "backlight" elsewhere in the tree.
Cc: stable <stable@vger.kernel.org> # 3.7
Fixes: eebfdc17cc6c ("backlight: Add TPS65217 WLED driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d1cc0ec3da23e44c23712579515494b374f111c9 upstream.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mfd node was also prematurely freed,
while the child backlight node was leaked.
Cc: stable <stable@vger.kernel.org> # 3.9
Fixes: 47ec340cb8e2 ("mfd: max8925: Support dt for backlight")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
